Specs

Specifications
subject to change.
Meets
requirements of
ASSE 1006
USA
10200 David Taylor Drive
Charlotte, NC 28262
1-800-FRIGIDAIRE
frigidaire.com
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
1-800-265-8352
frigidaire.ca
*Height only adjustable to 35
3
/4" max. when installed in 35
3
/4" max.
standard cabinetry cutout. (Dimensions do NOT include insulation –
insulation blanket may be compressed during installation.)
33
3
/4"
Adjustable
to 35
3
/4"
*
Front
23
3
/4"
24" Built-In Dishwasher w/Integrated Controls (IC)
w/Stainless Tub (ST) Gallery (Q, R & S Models)
Left
24
1
/4"
Power supply & water inlet location
(bottom rear)
50
1
/4"
Right
Door in 90°
open position
27
3
/4"
22
1
/2"
3
1
/2"
min.
to
4
1
/2"
max.
1"
2
1
/4"2
1
/4"
**
NOTE: 35
3
/4"
max.
height for standard
cabinetry cutout.
(
5
/16"
min. clearance
required from unit to
underside of countertop.)
3"
18"
24"
min.
Electrical, water,
and drain
lines
must be confined
to shaded
area
1
1
/4"
24"
3
"
90°
90°
Preferred
drain areas
3
"
34"
min.
to
35
3
/4"
max.
**
Dishwasher Specifications
Product Shipping Weight (approx.) – 91 Lbs.
Voltage Rating – 120V / 60 Hz / 15 Amps (maximum 20 Amps if
connected with disposer)
Connected Load (kW Rating) @ 120 Volts = 1.44 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
Amps @ 120V = 15 Amps
Always consult local and national electric & plumbing codes.
Meets requirements of ASSE 1006 — integral air gap on supply.
Water Pressure – Hot water line to dishwasher must provide
between 20 and 120 pounds per square inch (psi) with at least 120° F
hot water temperature.
Make sure location has correct drain, water and electrical outlets
to make connections — MUST be confined to shaded areas.
Electrical and water supplies should enter cabinet opening on floor,
or through back or side walls, as shown in shaded areas.
Keep back free of drain, water & electrical supply.
Connections preferably located toward left side of dishwasher.
Do not cross drain, water or electrical lines in front of motor, blower
or frame.
If connecting drain hose to sink trap, local code may require
installation of Air Gap Kit (not included).
Leveling legs supplied to adjust height. (Note: Height only adjustable
to 35-3/4" max. when installed in 35-3/4" max. standard cabinetry
cutout. 5/16" min. clearance required from top of unit to underside
of countertop. Dimensions do NOT include insulation — insulation
blanket may be compressed during installation.)
When installing adjacent to wall, cabinet or other obstruction that
extends beyond front edge of unit, allow 2" minimum clearance
between opened door and obstruction.
Floor should be flat and free of obstructions with carpet removed
to provide motor clearance.
When installing at end of cabinet line, sides and back must be
fully enclosed.
Do not install unit under a cooktop, damage will occur.
Recommended to seal cabinets, enclosing all sides of dishwasher,
including underside of countertop, with oil-based paint or moisture-
proof polyurethane to prevent possible steam/moisture damage.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
FGID2476S 10/16 © 2016 Electrolux Home Products, Inc.
Dishwashers
FGID2476S F / W / B 24" Built-In