INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. 3, Tip Over Hazard = Child or adult can tip the range and be killed. + Verily the anti-tip device has been installed fo floor or wall. * Ensure e nil-tip device is re-engaged when the range is moved to floor or wall. *» Do not operate the range without the anti-tip device in place and engaged.
IMPORTANT SAFETY INSTRUCTIONS + Installation of this range must conform with local codes or, in the absences of local codes, with the National Fue Gas Code ANS! edition when installed in the United States.
Tools you will need {(Wear safely glasses when using loos: For leveling legs and Anti-Tip Bracket: = Adjustable wrench or channel lock pliers (Fig. a} + 5/16" Nut driver or flat head screwdriver (Fig. b) = Electric drill & 1/8° drill bit (318" Masonry drill bit if installing in concrete)} (Fig. ¢ + Level (Fig. d) For gas supply connection: + Adjustable wrench and pipe wrench (Figs. a & &) For burner flame adjustment: » Philips head and small flat-blade screwdrivers (Figs.
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions 1 Emmanuel between tha tango and adjacent combustible surfaces. 3 3 ailed. Check for proper electrical supply, and the stability of the floor. 3. Dimensions that are shown must be used. Sven dimensions provide minimum clearance. Contact surface must be solid and level.
Install anti-tip bracket IMPORTANT SAFETY WARNING! To reduce the risk of tipping of the range, the range must be secured to the floor by properly instated an{i-tip bracket and screws packed with the tangs. Failure to install the anti-lip bracket will allow the range to {ip over if excessive weight is placed on an open door or if a child climb upon it. Serious injury might result from spilled hot liquids or from the range itself.
Provide an adequate gas supply. When shipped from the factory, this unit is designation operate on 4” {10,186 om) water column (1,0 kPa) natural gas manifold pressure. A convertible pressure regulator is connected o be ranges manifold and must be connected in saris with the gas supply line. If an LP/Propane conversion kit has been used, follow the instructions provided with the kit for convincing the pressure regulator fo LPf Propane use.
¢ Tighten the gas supply lifting and for appliance conduit 1o flare union adaption an the right side of the pressure regulator (refer fo Fig. 10} using RO MORE THAN of torque. Be sure to stabilize the 1/2" flare union adapter with an adjustable wrench before tightening the gas supply fitting and/or appliance conduit. ig. 10 d. Insist flare union adapter to external manual shut-off valve {See Fig. 8). e. Almach flexible appliance conduit to flare union adapter on shut-off valve (See Fig. 8). f.
Read the following electrical connection details before connecting electricity to range. STEFANIE] Be tore servicing, disconnect electrical supply at circuit breaker, fuse or power cord. Electra] i nis: Dedicated, properly groused and polarized branch circuit protected by a 15 amp. circulate breaker or ime delay fuse. Ses serial plate for proper voltage. Extensive i dong: Because of potential safety hazards under certain conditions, we strongly recommend against the use of any extension cord.
Check ignition of surface burners. Operation of slack ignites should be checked after range and supply line connectors have been carefully checked for ‘sake and range has been connected fo elev tic power. a. To check for proper ignition, push in and turn a surface burner knob counterclockwise (o the LITE position. You will hear the ignite sparking. b The surface burner should ignite when gas is available 1o the boomer. Purge air from supply lines by leaving knob in the LITE position unit boomer ignites.
Make sure range is level. Level the range by placing a level horizontally on an oven rack. Check diagonally from front fo back, then elev the range by either adjusting the leveling legs or by placing shims under the corners of the range as needed. Mol After installation is complete, make sure alf controls are left in the off position. Care, cleaning and maintenance Refer to the User's manual for detailed dealing instructions.
« Nunca uss la estufa para calentar el cuarto. El uso prolongado de la estufa sin 'a adecuada ventilación puede resultar peligroso. » Almacenos ni utilice gasolina u loros vapores y [quedos inflamables an la proximidad de éste o de cualquier otro artefacto eléctrico. Puede provocar incendio o explosión. » Ajuste todos los controles a la posición "OFF” {apagada)} después de haber hecho una operación con tiempo programado. « Diferencia de la gama estándar cocinas de gas, ESTA PLANCHA DE COCINA NO ES MOVIBLE.