Installation guide

ManualsBrandsFrigidaire ManualsLaundry centerOfficial Frigidaire stacked laundry center

Tumble Action Laundry Center

Gas & Electric

Before beginning installation, carefully read these instructions. This will simplify the installation

and ensure the laundry center is installed correctly and safely. Leave these instructions near the

laundry center after installation for future reference.

NOTE: The electrical service to the laundry center must conform with local codes and ordinances

and the latest edition of the NationalElectrical Code, ANSI/NFPA 70, or in Canada, the Canadian

Electrical Code, CSA C22. I

NOTE: The gas service to the laundry center must conform with local codes and ordinances and

the latest edition of the Nationa/Fue/ Gas Code ANS/Z223. 1/NFPA 54, or in Canada, the Canadian

Natural Gas and Propane Installation Code. CSA B 149. 1.

NOTE: Thelaundry center is designed under ANSI Z21.5.1 or ANSI/UL 2158- CAN/CSA C22.2 (latest

edition) for HOME USE only. This laundry center is not recommended for commercial applications

such as restaurants or beauty salons, etc.

For your safety the information in

this manuaI must be foIIowed to minimize the risk

of fire or expIosion or to prevent property damage,

personal injury or loss of life.

- Do not store or use gasoiine or other flammable

vapors and Iiquid in the vicinity of this or any

other appIiance.

- WHAT TO DO IF YOU SMELL GAS

® Do not try to light any appliance.

0 Do not touch any electrical switch; do not use

any phone in your building.

® Clear the room, building or area of all

occupants.

0 immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

® if you cannot reach your gas supplier, call the

fire department.

installation and service must be preformed by a

qualified installer, service agency or the gas

supplier.

Contents

SUBJECT PAGE

Pre-lnstallation Requirements

Electrical Requirements

Water Supply Requirements

Drain Requirements

Exhaust System Requirements

Gas Supply Requirements

Location

Mobile Home Installation

Rough-In Dimensions

Unpacking

Electrical Installation

Grounding Requirements

3 & 4-Wire Connections

Installation

Replacement Parts

Printed in U.S.A. P/N134395100C (0408)

Summary of content (8 pages)

PAGE 1
Tumble Action Before beginning and ensure laundry installation, the laundry center after the latest Electrical NOTE: the latest Natural of the The gas service edition instructions. correctly and safely. is installed for future This will Leave simplify these the installation instructions near the reference.
PAGE 2
PRE-INSTALLATION REQUIREMENTS Tools and Materials Required for Installation: 1. Phillips head screwdriver 2. Channel-lock adjustable pliers 3. Carpenter's level 4. Flat or straight blade screwdriver 5. Duct tape 6. Rigid or flexible metal 4 inch (10.16 cm) duct 7. Vent hood 8. Pipe thread sealer (Gas) 9. 1/4 inch socket w/ratchet 10.3/8 inch socket w/ratchet 11.3/8 inch open end wrench 12.7/16 inch open end wrench 13.
PAGE 3
EXHAUST SYSTEM REQUIREMENTS Use only 4 inch (10=16 cm) diameter
PAGE 4
GAS SUPPLY REQUIREMENTS 1. Installation MUSTconform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition) or in Canada, the current AN/CGA B149. 2. The gas supply line should be of 1/2 inch (1.27 cm) pipe. 3. If codes allow, flexible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be constructed of stainless steel or plastic-coated brass. 4. The gas supply line MUST have an individual shutoff valve. 5.
PAGE 5
ROUGH-IN DIMENSIONS 25_ iN. (64.13CM) 2 _/_IN. (6.35cM) 47" -- 16_/4IN. (41.27 CM) _-- T 5 Y4IN. (13.33 CM) O_gNNECTION 53 raN. 134.62 CM.) 1_ t 421/4IN. -OO J_ (107.32 CM.) WA%RINLEIS 1 7/8 IN. (4.76 OM) \\\\ / (191.14 CM. 751/4IN. \ GAS8JFFLY 351N. (91.44 CM.) -- 31/_1N. (7.94 CM.) 401/2IN. (102.87 CM, (8&65 G 441N, (111.76 CM.) I 27 IN. __ (66.58CM) UNPACKING 1.
PAGE 6
ELECTRICAL INSTALLATION ALL ELECTRICLaundry Centers _ The following for proper center. are specific and safe electrical Failure electrical to follow shock and/or installation Canadian requirements _ of your laundry these instructions can create Improper grounding an with a fire hazard.
PAGE 7
2. The laundry center is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from the plug. ELECTRICAL CONNECTIONS 3-WIRE SYSTEM FOR A NON-CANADIAN ELECTRICLaundry L_nter 1 1. Remove the screw securing the terminal block access cover to the rear panel and remove cover. 2. Install a U.
PAGE 8
7. GAS CONNECTION 10. Connect the exhaust duct to outside duct work. Use duct tape to seal all joints. 11. Plug the power cord into a grounded outlet. NOTE: Check to ensure the power is off at a circuit breaker/fuse box before plugging the power cord into an outlet. 12. Turn on the power at a circuit breaker/fuse box. (Gaslaundry centers only) a. Remove the shipping cap from gas pipe at the rear of the dryen NOTE: DO NOT connect the laundry center to LR gas service without converting the gas valve.