Installation Guide

ManualsBrandsFrigidaire ManualsAppliance AccessoriesGallery 27" Black Stainless Steel Microwave Trim Kit

Installation Instructions

Installation

Instructions

Built-in Trim Kit

Model #

BEFORE YOU BEGIN

•

IMPORTANT

– Save these instructions

for local inspector's use.

•

IMPORTANT

– Observe all governing

codes and ordinaces.

•

Note to Installer

– Be sure to leave

these instructions with the Consumer.

•

Note to Consumer

– Keep these

instructions for future reference.

• Skill level - Installation of this appliance

requires basic mechanical and electrical

skills.

Read these instructions completely and carefully.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

• Unplug the microwave oven before

attempting installation of this kit.

• Because the kit includes metal parts, caution

should be used in handling and installation to

avoid the possibility of injury.

• Do not remove permanently affixed labels,

warnings, or plates from the product. This

may void the warranty.

FOR YOUR SAFETY:

WARNING

– Before beginning the installation,

switch power off at service panel and lock out

When the service

cannot be locked, securely

fasten

a prominent warning device,

such as a tag, to

the service panel.

IMPORTANT - PLEASE READ

AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE

ONLY WITH ELECTROLUX MICROWAVE

OVENS SPECIFYING BUILT-IN KIT

QUESTIONS?

For customers in the United States call:1-800-944-9044

For customers in Canada call: 1-800-265-8352 (English)

1-800-668-4606 ext.8199 (French)

Visit our Website at: www.frigidaire.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

PN:

EN-1

A06823528

September 2021

to prevent being switched on accidentally.

GMTK3068AF GMTK2768AF GMTK3068AD

GMTK2768AD

Please make sure the cabinet is level orvertical

to front panel of cabinet before installation.

Uneven cabinets may cause the trim kits to be

noncoplanar with the door panels of microwave

oven.

•

PN:16170000A87093

A statement shall be included in the instructions

warning the user that the appliance must be

disconnected from the source of supply before

attempting the installation of the accessory, and

that the accessory is intended for use only with

an appliance that is marked to indicate such use.

•

Summary of content (5 pages)

PAGE 1
Installation Instructions Installation Built-in Trim Kit Instructions Model # GMTK3068AF GMTK2768AF GMTK3068AD GMTK2768AD BEFORE YOU BEGIN • Read these instructions completely and carefully. IMPORTANT – Save these instructions • for local inspector's use. • IMPORTANT – Observe all governing codes and ordinaces. • Note to Installer – Be sure to leave these instructions with the Consumer. • • • • Note to Consumer – Keep these instructions for future reference.
PAGE 2
Installation Instructions PARTS INCLUDED IN THE KIT 1. Front Frame Assembly- QTY 1 2. Exhaust Duct - QTY 1 Bottom Mounting Rail – QTY 2 3. Screw A - QTY 11+ 3 extra Screw A 4. Screw B - QTY 4 + 2 extra CHOOSING A LOCATION FOR YOUR MICROWAVE OVEN IF BUILT-IN Front Frame Assembly Screw B Built-In Trim Kit allows for the installation of microwaves listed below to be built into a cabinet or wall by itself or over an electric wall oven*.
PAGE 3
Installation Instructions Screw A Center Line Illustration 3 ELECTRICAL OUTLET LOCATION Outlet should NOT be in the shaded area as indicated on Illustration 3 NOTE 1: The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven. Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling and rear partition.
PAGE 4
Installation Instructions Bottom Mounting Rail Turn microwave upside down so you are looking at oven bottom. Secure the bottom Mounting Rail on oven with four SCREWS A. See Illustration 5. NOTE: Please make sure to align the holes(marked with “36”) of bottom mounting rail and the holes(marked with “36”) of microwave oven's bottom plate. OVEN INSTALLATION 1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet. 2.
PAGE 5
Installation Instructions FRAME INSTALLATION 1. 2. Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven. See Illustration 7. Check that it is level and then secure with two SCREWS B. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS B. See Illustration 8.