PROFESSIONAL SERIES Model PL36WC50EC ENGLISH ..................................... 3 FRAN(_AmS................................
_, _ INTENDED FOR DOMESTIC COOKING ONLY _, WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR iNJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent power from being switched on accidentally.
OPERATION BLOWER Controls LIGHT SWITCH The hood is operated using the (4) push-buttons edge of the hood. MEDIUM PILOT SPEED LAMP located at eye-level, on the front BLOWER ON-LOW The light switch turns the halogen lamps on and off. BLOWER HIGH SPEED / OFF SWITCH The blower on-low / off switch turns the blower on to its lowest running speed. The blower must be turned on using this switch. Turn the blower off by pressing this switch a second time.
PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket 8 - Mounting Screws (4.8 x 38mm Pan Head) 4 - Mounting Screws (3.9 x 9.5mm Pan Head) 2 - Mounting Screws (3.9 x 6ram Flat Head) 8 - Drywall Anchors 1 - Installation Instructions DISCHARGE COLLAR MOUNTING BRACKET SCREWS (3.9 X 9.5ram Pan Head) 4 MOUNTING 2 MOUNTING BRACKET SCREWS (3.
iNSTALL [ THE DUCTWORK ] (DUCTED HOODS ONL Y) ,_ ROOF CAP \ CAUTION: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions wilt reduce the performance of the hood. Use as few of them as possible. Larger duct!rig may be required for best performance with longer duct runs. 4. Install a roof or wall cap.
INSTALL FLUE MOUNTING (DUCTED AND NON-DUCTED BRACKET HOODS) 1. Assemble the flue mounting bracket, adjusting outside width as shown. 2. Carefully See Figure 7. center the mounting bracket directly over the range hood location. 3. Secure the bracket assembly to the ceiling using (2) 4.8x38mm mounting screws and drywall anchors (Fig. 8). Make sure the bracket is pushed into the corner, tight against the wall and centered over the hood. FLUE MOUNTING BRACKET DRYWALL 3.
PREPARE THE HOOD (NON - DUCTED HOODS ONLY) Note: The following materials must be purchased separately o Non - Ducted Recirculation Kit, Model DFKTWC50EC. for non-ducted recirculation installations. o 5" diameter metal duct. 1. Discard discharge collar supplied with the hood. Install the 5" to 6" adapter supplied with the Non-Ducted Recirculation Kit. Fig. 10. 2. Secure the plenum to the flue mounting bracket with (2) 3.
MAKE ELECTRICAL CONNECTIONS WARNmNG: Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring. 1. Remove the wiring box cover. Remove a knockout from tile wiring box. 2. Secure the conduit to the wiring box through a conduit connector. 3. Make electrical connections. Connect white to white, black to black and green to green. 4.
iNSTALL FILTERS (DUCTED AND NON-DUCTED HOODS) 1. To remove the GREASE filter, push in on the metal latch tab and tilt filter downward to remove. 2. To install the GREASE filter, align rear filter tabs with slots in the hood. Depress the metal latch tab, push filter into position and release. Make sure filter is securely engaged after installation. NOTE: Prior to use, remove protective film from the filter frame. (NON-DUCTED HOODS ONL Y) 1.
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrotux wilt pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1. Products with original serial numbers that have been removed, altered or cannot be readily determined. 2.
SERVICE PARTS- LISTE PIECES DE RECHANGE MODELS PL36WCSOEC KEY No.
SERVICE PARTS - USTE PIECES DE RECHANGE MODEL PL36WCSOEC 120 86 116 115 ............ 152 119 118 62 407 230 ..... ALA & 234 240 223 229 26 _ - _PPPP ......
