Specifications
INSTALLATION SPECIFICATIONS
•
Product Shipping Weight (approx.) – 365 Lbs.
•
An electrical supply with grounded three-prong receptacle is required. The
power supply circuit must be installed in accordance with current edition of
National Electrical Code (NFPA 70) and local codes & ordinances.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.02 kW
•
Amps @ 120 Volts = 8.5 Amps
•
Always consult local and national electric & plumbing codes.
•
Floor should be level surface of hard material, capable of supporting fully
loaded refrigerator.
•
Minimum 3/8" clearance required for sides and top of refrigerator or freezer
with 1" clearance at rear to allow for ease of installation, proper air circulation,
and plumbing / electrical connections.
•
When installing refrigerator adjacent to wall, cabinet or other appliance that
extends beyond front edge of unit, 20" minimum clearance recommended
to allow for optimum 120° to 180° door swing, providing complete drawer /
crisper access and removal. (Absolute 4-1/2" minimum clearance will ONLY
allow for 90° door swing which will provide drawer / crisper access with
restricted removal.)
Minimum 3/8" clearance required for sides and top of
refrigerator or freezer with 1" clearance at rear to allow for ease of installation,
proper air circulation, and plumbing / electrical connections.
•
To ensure optimum performance, (do not install in areas where temperature
drops below 55° F or rises above 110° F) and avoid installing in direct sunlight
or close proximity to range, dishwasher or other heat source.
•
Refrigerator must be placed on level surface of hard material, same height
as flooring. Surface must support approximately 800 lbs. when fully loaded.
Unit equipped with 4-point leveling.
•
For proper ventilation, front grille MUST remain unobstructed.
•
Recess electrical outlet when possible.
•
Water recess on rear wall recommended to prevent water line damage.
•
Water Pressure – Cold water line must provide between 30 and 100 pounds
per square inch (psi).
•
Copper or stainless steel tubing with 1/4" O.D. recommended for water supply
line with length equal to distance from rear of unit to household water supply
line plus 7 additional feet. Optional Water Supply Installation Kits available.
•
Adjustable front rollers to assist with door alignment.
“BUILT-IN LOOK” SPECIFICATIONS
•
Minimum opening of 70-1/4" H x 36" W x 28-7/8" D required to allow for ease
of installation, proper air circulation, and plumbing / electrical connections.
•
Remove all wall / floor molding prior to installation.
FPBS2778UF 9/18
© 2018 Electrolux Home Products, Inc.
Specifications subject to change. Accessories information available on the web at frigidaire.com / frigidaire.ca
Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes.
Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com / frigidaire.ca.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FPBS2778UF
FRENCH DOOR REFRIGERATOR
26.7 CU. FT.
54 "
B
C
A
“Built-In Look”
Cutout Dimensions
(A) 70
1
/4" (B) 36" (C) 28
7
/8"
23
7
/8"
28
3
/4"
Standard
Refrigerator Depth
vs. Counter Depth
Counter Depth
Standard Depth
5"
34
3
/4
3
/8
"
68
5
/8"
with
3
/8"
rollers
32 "
28
3
/4"
69
7
/8"
with
3
/8"
rollers
Power
cord
location
(right
bottom
rear)
Water
line inlet
location
(left
bottom
rear)
35
5
/8"
Cabinet
36"
Doors
(with drawer
fully extended
including handle)
47
3
/8"
(with doors
90°
open)
28
7
/8" Side Panels,
1
/2" min. width
Top View
24"
Cabinet
25"
Countertop
Allow 1" min. clearance at rear
for proper air circulation and
water
/
electrical connections
Recessed
water line
Recessed
electrical outlet