Installation Instructions
Table Of Contents
- 30inch liner intruction manual V2
- 页 1
- 书签9BDCC503 Installation Instruction for Mounting Liners/Ventilators in Wood Range Hoods
- 书签35E61431 Rectangular Liners are to be used with Chimney and Mantel style Range Hoods.
- 书签3B095570 1\) Locate available studs in area where the Range Hood is to be installed. 2\) Align Range Hood so at least two screws will be secured through range hood mounting strip and into available studs on rear wall. 3\) Refer to manufacturers guidelines that accompany the stove/cooktop that will be located beneath the wooden range hood. 4\) Exposed wood edges should be no less than 30'' above cooking surface. 5\) Mount range hood securely to wall using minimum #8X2-1/2'' long framing screws\(not included\). 6\) Remove protective peel coat from liner \(if applicable\). 7\) Install ventilation Power Pack securely to Rectangular Shaped Steel Liner as outlined in ventilator instruction packet. Ventilator cut out to be oriented as shown in diagram below. 8\) Secure Liner/Ventilator assembly to inside of range hood opening using available mounting holes\(a\) and secure with wood screws\(#6X1/2'' not included\). 9\) Install duct work or ductless kit to ventilator power pack according to manufacturer's guideline. 10\) If Chimney Hood is being installed, attach chimney extension over ductwork and fasten to wall with framing screws, securing to studs where available. If studs are not present in mounting area, use drywall anchors. 11\) If Mantel Hood is being installed, mount doors or decorative panels as appropriate.
- 书签E0C4636E 720.5mm/28.3 in
- 书签0EEC997B 265.1mm/10.4 in
- 书签A2FA6656 495.3mm/19.5 in
- 书签07115CF6 259.1mm/10.2 in
- 书签41A91B4E 460.2mm/18.1 in
- 书签B5DE563F 102.2mm/4 in
- 书签9D14928C \(a\)
- 书签37300781 \(a\)
- 书签753D8E06 \(a\)
- 书签D99323CC \(a\)
- 书签F422FABA \(a\)
- 书签D5BAFB81 \(a\)
- 书签285EF69D HYT08US54002
- 页 1
- 36inch liner intruction manual V2
- 页 1
- 书签6158A826 871.7mm/34.3 in
- 书签73B7F933 265.1mm/10.4 in
- 书签D84BC458 495.3mm/19.5 in
- 书签0C959C54 259.1mm/10.2 in
- 书签64908364 460.2mm/18.1 in
- 书签69306CE3 Installation Instruction for Mounting Liners/Ventilators in Wood Range Hoods
- 书签28DA27F8 Rectangular Liners are to be used with Chimney and Mantel style Range Hoods.
- 书签203A5265 1\) Locate available studs in area where the Range Hood is to be installed. 2\) Align Range Hood so at least two screws will be secured through range hood mounting strip and into available studs on rear wall. 3\) Refer to manufacturers guidelines that accompany the stove/cooktop that will be located beneath the wooden range hood. 4\) Exposed wood edges should be no less than 30'' above cooking surface. 5\) Mount range hood securely to wall using minimum #8X2-1/2'' long framing screws\(not included\). 6\) Remove protective peel coat from liner \(if applicable\). 7\) Install ventilation Power Pack securely to Rectangular Shaped Steel Liner as outlined in ventilator instruction packet. Ventilator cut out to be oriented as shown in diagram below. 8\) Secure Liner/Ventilator assembly to inside of range hood opening using available mounting holes\(a\) and secure with wood screws\(#6X1/2'' not included\). 9\) Install duct work or ductless kit to ventilator power pack according to manufacturer's guideline. 10\) If Chimney Hood is being installed, attach chimney extension over ductwork and fasten to wall with framing screws, securing to studs where available. If studs are not present in mounting area, use drywall anchors. 11\) If Mantel Hood is being installed, mount doors or decorative panels as appropriate.
- 书签FEC2F18C \(a\)
- 书签8602C813 \(a\)
- 书签2AAD69A5 \(a\)
- 书签CBFB3407 \(a\)
- 书签B911D0FE \(a\)
- 书签F153426C \(a\)
- 书签670AFC1F 102.2mm/4 in
- 书签34F0E9E7 HYT03US54003
- 页 1