IMPORTANT INSTRUCTIONS & OPERATING MANUAL Vienna 2 in 1 (Wall Mount & Floor Standing) Color Changing LED Fireplace Item No: VWF-1/0305 Read these instructions carefully before attempting to assemble, install, operate or maintain the product. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and / or property damage. Retain instructions for future reference.
GENERAL SAFETY INFORMATION When using this fireplace, basic precautions should always be taken to reduce the risk of fire, electric shock and injury to persons, including the following: CAUTION – Due to the high temperature, keep electrical cords, drapery and other furnishings at least 3 feet from the front, side and rear of the fireplace. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
23. Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that the fireplace plug properly fits into the outlet before each use. During use, make sure the fireplace plug does not overheat. If necessary, have a qualified electrician check and / or replace the wall outlet. 24. Do not place the fireplace near a bed for objects such as pillows or blankets can fall off the bed and be ignited by the fireplace. 25. Never clean this fireplace while it is plugged in.
Quick Reference Guide Sr. No Prior to installation, please ensure that the voltage and capacity of your power outlet is compatible with your fireplace. Your fireplace may emit a slight, harmless odor during its first use. This odor is a normal reaction caused by the initial heating of internal fireplace parts and it will not occur again. It is normal for fireplace to make a rattling sound for a short duration of time during its first use.
Helpful Advice Before Installation Please retain all packaging until you have checked and counted all the parts and other package contents. The package contains small apparatus which should be kept away from young children and infants. We suggest that you move all the smaller parts into a container to reduce the risk of losing them. At least 2 people are required to install this fireplace. It is recommended to place your fireplace near an existing outlet, for ease of electric connection.
34.6 inch 22 inch 6.3 inch 2 feet Step One Keep the top of the fireplace at least 3 feet away from the ceiling or other objects for optimum heat ventilation. For optimum viewing, place four marks on the wall with respect to the recommended fixed dimensions for the top screws (see figure below). Note: use a level when marking the positions of the holes to ensure that the bracket is mounted horizontally.
Step Two Make sure the area to be drilled does not have any hidden electrical wires or water and gas pipes. The wall fixings provided is for concrete walls only; please use suitable fixings for your wall type. If in doubt, contact a qualified hardware expert. Drill holes into the wall with respect to the four markings and then insert the screw anchors. Next, place the bracket onto the wall such that the holes are aligned.
Step Five Place the front glass panel over the front of the fireplace aligning the slots in the brackets at each side of the front panel with the knobs on the sides of the fireplace. Slot the front facade down ensuring that the brackets are fully interlocked.
Installation (Floor Standing) Place the fireplace on a flat table. Attach the floor standing base to the fireplace using the provided screws. Place the fireplace upright. Unpack the pebbles from the bag and place them along the unit in the desired position. Please note the pebbles are located inside the polystyrene bag.
Place the front glass panel over the front of the fireplace aligning the slots in the brackets at each side of the front panel with the knobs on the sides of the fireplace. Slot the front facade down ensuring that the brackets are fully interlocked. ↓ . Instructions for Use This fireplace can be operated either by the switches located on the top right hand side of the fireplace or the supplied remote control.
Remote Control Operation (continued) Press the standby button on the remote control once to turn on the fireplace with flame effect. Press the “750W” button once for low heat setting. Press the button again to switch off the heat. Press the “1500W” button once for high heat setting. Press the button again to switch off the heat. Press the “DIMMER” button to change the flame color.
Cleaning & Maintenance Disconnect from the power supply before attempting any maintenance or cleaning in order to reduce the risk of fire, electric shock to persons or damage to property. Warning - Always disconnect from the power supply before cleaning fireplace. For general cleaning, use a soft, clean duster. Never use abrasive cleaners. The glass viewing screen should be cleaned thoroughly with a soft cloth. Do NOT use proprietary glass cleaners.