IMPORTANT INSTRUCTIONS & OPERATING MANUAL Valencia Wide Screen Log Flame Wall Hanging Electric Fireplace Item No: VWWF-1/0306 Read these instructions carefully before attempting to assemble, install, operate or maintain the product. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and / or property damage. Retain instructions for future reference.
GENERAL SAFETY INFORMATION When using this fireplace, basic precautions should always be taken to reduce the risk of fire, electric shock and injury to persons, including the following: CAUTION – Due to the high temperature, keep electrical cords, drapery and other furnishings at least 3 feet from the front, side and rear of the fireplace. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
23. Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that the fireplace plug properly fits into the outlet before each use. During use, make sure the fireplace plug does not overheat. If necessary, have a qualified electrician check and / or replace the wall outlet. 24. Do not place the fireplace near a bed for objects such as pillows or blankets can fall off the bed and be ignited by the fireplace. 25. Never clean this fireplace while it is plugged in.
Sr. No Item Description Quantity 001 Carton 1 002 Electric Fireplace 1 003 Foam Protection (Left) 1 004 Mounting Screws Tube ST5x40 005 Instruction Manual 1 006 Remote Control 1 007 Cable Plug 1 008 Foam Protection (Right) 1 and Screw 6 Helpful Advice Before Installation Please retain all packaging until you have checked and counted all the parts and other package contents.
Installation Do not connect the fireplace to the power supply until properly fixed to the wall and the instructions are carefully read. Make sure the area to be drilled does not have any hidden electrical wires or water and gas pipes. The minimum distances must be observed as shown in the diagrams below. During installation of the fireplace, avoid any possible damage to concealed cables. Please be careful when drilling holes. This fireplace is designed to be permanently fixed to a wall.
Step One Keep the top of the fireplace at least 3 feet away from the ceiling or other objects for optimum heat ventilation. For optimum viewing, place four marks on the wall with respect to the recommended fixed dimensions for the top screws (see figure below). Note: use a level when marking the positions of the holes to ensure that the bracket is mounted horizontally. Step Two Make sure the area to be drilled does not have any hidden electrical wires or water and gas pipes.
Turning On Plug the fireplace into a power outlet. Turn on the power switch which is located on the right side of the fireplace.
Description of Remote Control Power Switch Plug the fireplace into a power outlet. The fireplace is now in Standby mode. Press the button once to turn on the fireplace and flame effect. An indicator light will light up to indicate that the function is on. This will also turn on the flame effect. Press the button once to turn off the flame effect. This will put the fireplace back into Standby mode. Heat Control Press the “Heat Control” button once for the low heat setting.
Remote Control The remote control requires 2 AAA batteries, which are not included. Point the remote control directly at the fireplace. The range is about 11.5 feet. Replacing the Light Bulb This fireplace consists of 4 bulbs (E-12, 40W) that illuminate a flame effect. The light bulbs need to be replaced if you notice a dark section of the flame or when the flames lose clarity.
Troubleshooting Problem Possible Solution · Check if the unit is plugged in the power outlet. · Check if the unit is in Standby mode. If so, turn the unit ON. · Check if the heat is turned OFF. · Check for safety cut-off operation. Unit does not work / does not heat · Check if the unit is plugged in the power outlet. · Check if the unit is in Standby mode. Turn the unit ON.
