Installation Manual

ManualsBrandsFront Runner Manuals4WD & CampingGas/Propane Bottle Holder

GBHO012_REV_A01

Gas / Propane

Bottle Holder

front runner

GBHO012

ENG

Thank you for purchasing a Front Runner Gas / Propane Bottle Holder.

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.

Refer to Page 2 for a list of all the components, quantities and tools required.

READ ME !

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD

RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT

RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND

DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO

INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY

FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

Summary of content (5 pages)

PAGE 1
front runner ENG Gas / Propane Bottle Holder GBHO012 READ ME ! Thank you for purchasing a Front Runner Gas / Propane Bottle Holder. Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received. Refer to Page 2 for a list of all the components, quantities and tools required. IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
PAGE 2
GET ORGANIZED 1 IN THE BOX 1 2 3 4 5 6 7 8 1X 2X 2X 2X 4X 4X 4X 4X TOOLS NEEDED Top Collar Base Clamp Bracket Tensioner Bar T - Slot Rubber M8 Nut Cap M8 Nyloc Nut M8 x 16 x 1.6 SS Flat Washer M8 x 16 Hex Bolt 13mm 13mm FIGURE 1.
PAGE 3
FIT AND SECURE - MOUNTING BRACKETS ON TOP OF SLATS 2 2.1 Find a suitable place between two slats to mount your Gas Bottle Holder. Slide two M8 x 16 Hex Bolts (Item 8) into the machined slots of the slats you have chosen, followed by the Base Clamp Bracket (Item 2). 5 6 7 13mm 2 Loosely ﬁt using M8 x 16 x 1,6SS Flat Washers and M8 Nyloc Nuts (Items 6 & 7). The position of the Base Clamp Brackets will depend on the size of your gas bottle. 8 Place your gas bottle between the two Base Clamp Brackets.
PAGE 4
FIT AND SECURE - MOUNTING BRACKETS AT THE BOTTOM OF THE SLATS 3 3.1 Find a suitable place between two slats to mount your Gas Bottle Holder. Slide two M8 x 16 Hex Bolts (Item 8) into the machined slots underneath the slats you have chosen, followed by the Base Clamp Brackets (Item 2). 8 2 13mm 7 Loosely ﬁt using M8 x 16 x 1,6SS Flat Washers and M8 Nyloc Nuts (Items 6 & 7). 6 The position of the Base Clamp Brackets will depend on the size of your gas bottle.
PAGE 5
4 FINISH Congratulations! You did it. Take a step back and admire your work! 5 INSTALL OTHER VEHICLE AND RACK ACCESSORIES Now's the time to visit your favorite Front Runner Dealer in person or online. Be sure to tag us.