Q X7 ACCESS User Manual

FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
Due to unforeseen changes in production, the information contained in this manual is subject to change without notice. Pay spec ial
attention to safety where indicated by the following marks:
Meanings of Special Markings
DANGER - procedures which may lead to dangerous conditions and cause death/serious injury if not carried out properly.
WARNING - Procedures which may lead to a dangerous condition or cause serious injury and even death to the user if not carried
out properly or procedures where the probability of superficial injury or physical damage is high.
CAUTION - Procedures where the possibility of serious injury to the user is small, but there is a danger of injury or physical damage,
if not carried out properly.
NOTE – Steps, Tips or information
WARNING - Always keep electrical components away from children.
Introduction
Version
1.0
FrSky 2.4GHz Taranis Q X7/X7S ACCESS Manual
Version
1.0
FrSky 2.4GHz Taranis Q X7/X7S ACCESS Manual
Version
1.0
FrSky 2.4GHz Taranis Q X7/X7S ACCESS Manual
Version
1.0
FrSky 2.4GHz Taranis Q X7/X7S ACCESS Manual
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [e-mail]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [e-mail]
Long press the Encoder Button there will generate a pop-up where the user can reset timer, reset telemetry values,
reset all above, jump to the tele setup page.
Quick select options
Navigate the Menu
To navigate the menus, Taranis Q X7/X7S ACCESS has the following elements:
● Encoder Button
● MENU Button
● PAGE Button
● EXIT Button
Warnings for Battery
Do not remove the battery from the
Taranis Q X7/X7S ACCESS transmitter while the voltage warning is blinking
as this could cause internal settings and memories to be destroyed.
Do not use the transmitter if a “Backup Error” warning occurs.
Taranis Q X7/X7S ACCESS supports OpenTX system
Encoder Button
To navigate menus or widgets, turn the button to left or right as navigation.
MENU Button
To go to the [Model] menu, press the button.
To go to the [RADIO SETUP] menu, press the button, and hold for one second.
PAGE Button
To go to switch the page, press the button.
To go to the [Telemetry] menu, press the button, and hold for one second.
EXIT Button
To exit current page or operation widgets.
System item Currently selected page
Where am I in the menu tree
Overview of the menu tree
Press the MENU button and hold for one second.Press the MENU button.
Press the PAGE button and hold for one second.
To change the data in other
items, firstly Encoder
Button turn to the left or
right until the cursor stays
at the needed item.
Secondly, press Encoder
Button and turn the button
to the left or right.
To go to the next page, move the
cursor to the item, then Encoder
Button turn to the left or right.
The cursor will firstly stay at the item
which indicates the current page.
The Taranis Q X7/X7S ACCESS features 24 channels with a faster baud rate and lower latency thanks to its
high-speed module digital interface. As with the rest of the ACCESS transmitters, it provides a secure and reliable
link, along with wireless firmware updating making it fully compatible with our newest line of OTA receivers. The
battery compartment now uses 2 18650 Li-Ion batteries and can be balance charged via the Mini USB interface.
The Taranis Q X7S ACCESS version features Hall-sensor gimbals and the PARA wireless trainer function, making
it compatible with the FrSky Free Link App and AirLink S, while the wired training port is still retained.
Specifications
● Model name: Taranis Q X7/X7S ACCESS
● Dimension: 202.2mm*189.4mm*96mm
● Weight: Taranis Q X7 ACCESS: 613g (without battery)
Taranis Q X7S ACCESS: 639g (without battery)
● Operating system: Open source operating system
● Number of channels: 16 (ACCST D16) / 24 (ACCESS) channels
● Operating Voltage Range: 6.5V~8.4V (2 S LI-battery, not including LiFePO battery)
● Operating Current: 160mA@7.2V typ
● Operating Temperature: -10℃~60℃ (14℉~140℉)
● Backlight LCD resolution: 128*64
● Model memories: 60 models (expandable by Micro SD card)
● Smart Port, Micro SD card slot, Mini USB Port and DSC Port
Overview
About USB 2S Li-battery balance charging :
The Green Power indicator LED state:
Led on: charging Led off: charge end Led flash: charge fault
Note:
1. Charge the battery with the USB adapter (Voltage:5V+0.2V Current:＞2.0A) when you use the USB
charging function.
2. The lower the initial charging voltage, the better the charging effect is when the voltage difference
between the two cells exceed 50 mV.
LiFePO battery is not supported.
*USB adapter Voltage: 5V+0.2V Current:＞2.0A
Features
● Ergonomic and compact design
● Installed with ACCESS protocol
● Supports spectrum analyzer function
● High-speed module digital interface
● Supports wired training function
● Haptic vibration alerts and voice speech outputs
● Easily accessible battery compartment (*Batteries not included, adaptive with replaceable 18650 Li-ion batteries)
● SA: 3 positions; Short Lever
● SB: 3 positions; Long Lever
● SC: 3 positions; Long Lever
● SD: 3 positions; Short Lever
● SF: 2 positions; Long Lever
● SH: 2 positions; Momentary, Long lever
Ensure that the battery connector polarity
is correct when connecting batteries into
the battery compartment, otherwise the
Taranis Q X7/X7S ACCESS might be
damaged.
Antenna
Antenna
Earphone port
S1
SF
SB
SA
S2
SH
SC
SD
Hook
Trainer Port
Stick Stick
J3
J4
J2
J1
Page
Menu
Exit
Digital Trim
LCD Display
ENT
Carrying Bar
Module Bay
Battery Cover
Smart Port TF Card USB Port
Comparison List
Taranis Q X7 ACCESS Taranis Q X7S ACCESS
Communication Protocol
Gimbal
High-speed module digital interface
Wired Training System
Haptic Vibration Alerts
Voice Speech Outputs
Easily Accessible Battery Compartment
Battery Charging System
(via mini USB Port) - 2S Li-battery
New PARA wireless training system
• High-speed training system with a lower latency
• Compatible with FrSky Free Link App and
AirLink S via mobile devices
ACCESS/ACCST D16
G7 Noble potentiometer gimbal
√
√
√
√
√
√
×
ACCESS/ACCST D16
M7 hall gimbal
√
√
√
√
√
√
√
Model Setup for Taranis Q X7/X7S ACCESS Internal RF Module
Enter the MODEL SETUP menu.
Step 1: Set the Mode for Taranis Q X7/X7S ACCESS Internal RF.
Go to the MODEL SETUP menu, and select the Internal RF, select [Mode] [ACCESS].
Step 2: Set the Channel Range
The Internal RF module of
Taranis Q X7/X7S ACCESS supports up to 24 channels. The channel range is configu-
rable,and needs to be confirmed before use.
Step 3: Set the Receiver Number
When you create a new model, the system will assign you a receiver number automatically, but this can be easily
changed. The range of the receiver number is 00-63, with the default number being 01 (use 00 is not recommend-
ed). Once the receiver is set to desired number and is bound to the
Taranis Q X7/X7S ACCESS , the bind procedure
will not need to be repeated unless the receiver number is changed. In this case, either set the receiver number to
the previous one or repeat the bind procedure.
Step 4: Registration
In ACCESS, select the Module [Reg] into Registration status. Then Press the F/S button and power on your
receiver, and select the “RX Name XX” and [ENTER] to complete the Registration process then power down the
receiver.
Note:
If two or three receivers are used at the same time, the UID should be set to different values.
Step 5: Automatic binding (Smart Match )
Move the cursor to Receiver1[Bnd],and select it , power your receiver, select the RX, and complete the process, the
system will confirm "Bind successful". (You do not need to press the "F/S" button in ACCESS to Bind. Refer to the
receivers manual for details)
TM