Heated Pass Through Installation, Operation, Service, and Parts Manual Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians. *8195931* 24-Hour Service Hotline 1-800-551-8633 Price: $6.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS 1. Parts Ordering and Service Information Parts orders may be placed directly with your local Frymaster Factory Authorized Service Center (FASC)/Distributor. A list of Frymaster FASC/ Distributors was included with the unit when shipped from the factory. Your nearest FASC can also be found on Frymaster’s Web site, Frymaster.com. or you can contact the Frymaster Service Department at 1-800-24-FRYER or 1-318865-1711.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS Power Requirements: • Voltage – 208 VAC • Frequency - 60 Hz • Single Phase • 20 amp Service 4. Operation 1. Plug the unit into the power source. * 2. Press the ON/OFF rocker switch to the ON position. 3. Place product in the HPT in accordance with the restaurant’s established procedures. THIS APPLIANCE IS EQUIPPED WITH A GROUNDING PLUG FOR YOUR PROTECTION AGAINST SHOCK HAZARD AND MUST BE PLUGGED INTO A PROPERLY GROUNDED RECEPTACLE.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS 5. Maintenance Daily 1. Remove all product and turn the unit off. 2. Allow the unit to cool. 3. Use a wet sanitized cloth to clean the heated surfaces of the unit. Use a nylon pot brush on hard to remove stains or food items. Monthly Remove the filter screen and clean it with a wet sanitized cloth. Dry the screen thoroughly before reinstalling it in the unit. 6. Service Procedures 6.1 Adjusting the Temperature A.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS 6.2 Replacing the Temperature Probe or High Limit Thermostat A. B. C. D. E. F. G. H. I. J. Disconnect the unit from the electrical power source. Turn the unit on its side. Remove the five screws from the chassis bottom. Set the unit down on its base. Carefully lift the cowl assembly upward until it is clear of the blower assembly, then lay it on the table behind unit.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS G. H. I. J. K. L. M. N. O. P. Q. R. S. T. U. V. W. 6.4 Disconnect the plate ground wire from the push-on terminal on the back wall of the air tower. Using a thin, sharp knife inserted between the plate and the HPT chassis, carefully cut the silicon adhesive between the plate and the sides of the chassis. Pry up one end of the plate, lifting it away from the chassis.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS F. G. H. I. J. K. L. M. N. O. P. Q. R. 6.5 Cut the wire ties on the wiring bundle and, one at a time, disconnect the wires from the failed assembly and connect the corresponding wire from the replacement motor. Position the replacement motor over the mounting studs and secure it in place with the 5 ⁄16-inch nuts removed in Step D. Reinstall the blower bridge and secure it in place with the 5⁄16-inch nuts removed in Step C.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS 7.
HEATED PASS THROUGH INSTALLATION, OPERATION, SERVICE, AND PARTS 8 Common Repair Parts List 1 2 4 8 5 3 6 7 11 9 10 12 ITEM PART # 1 826-1561 2 823-3922 3 810-1724 4 807-3308 5 807-3533 6 807-2820 7 807-2819 8 106-2790 9 826-1549 10 826-1551 11 807-3036 12 826-1959 * 810-2226 * 816-0418 * 811-0511 * 811-1042 * Not illustrated. COMPONENT Pad, Leg (pkg of 4) Divider Assembly Screen, HPT Filter Switch, Black ON/OFF Rocker Relay, 18-Amp Solid State Block, .25 X 1.
NOTICE IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER/DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID.
THIS PAGE INTENTIONALLY LEFT BLANK
Frymaster, L.L.C., 8700 Line Avenue, PO Box 51000, Shreveport, Louisiana 71135-1000 Shipping Address: 8700 Line Avenue, Shreveport, Louisiana 71106 TEL 1-318-865-1711 FAX (Parts) 1-318-219-7140 PRINTED IN THE UNITED STATES FAX (Tech Support) 1-318-219-7135 SERVICE HOTLINE 1-800-551-8633 Price: $6.
