全漢企業股份有限公司 FSP TECHNOLOGY INC. 台灣 桃園市建國東路 22 號 NO.22,Jianguo E, Rd.,Taoyuan City,Taiwan,R.O.C. TEL:+886-3-375-9888 FAX:+886-3-375-6966 SPECIFICATION FSP350-60GHC With -5V Output 9PA35092XX Main Feature: Meet 80plus Meet 2010 ErP Active PFC Circuit Full Range Input ATX2.3 Version MAR. 31, 2010 REV : 1.
全漢企業股份有限公司 FSP TECHNOLOGY INC. MODEL: FSP350-60GHC Revision History Rev Description Date 1.
1. GENERAL DESCRIPTION AND SCOPE This is the specification of Model FSP350-60GHC; AC-line powered switching power supply with active PFC (Power Factor Correction) circuit, meet EN61000-3-2 and with Full Range Input features. Also, 5Vsb power is less than 1Winput at power off mode (PS_ON input at high state) which is comply with ErP Lot 6 year 2010 requirement. The specification below is intended to describe as detailedly as possible the functions and performance of the subject power supply.
3. INPUT ELECTRICAL SPECIFICATIONS 3.1. AC INPUT Parameter Min. Nom.(1) Max. Unit 90 115 135 Vin (115VAC) VAC rms 180 230 265 Vin (230VAC) VAC rms 47 -63 Vin Frequency HZ ◆ Nominal voltages for test purposes are considered to be within ±1.0V of nominal. 3.2.
Table 1. Loading Table for Efficiency Measurements 350W(loading shown in Amps) Loading +12V1 +12V2 +5V +3.3V -12V +5Vsb FULL 10.66 10.66 9.45 9.92 0.38 1.90 TYPICAL 5.33 5.33 4.72 4.96 0.19 0.95 LIGHT 2.13 2.13 1.89 1.98 0.08 0.38 Table 2. Minimum Efficiency Vs Load Loading Voltage FULL TYPICAL LIGHT Required Minimum Efficiency 115V 80% 81% 80% Required Minimum Efficiency 230V 80% 82% 80% 3.4.
4.2. LOAD CAPACITY SPECIFICATIONS The cross regulation defined as follows, the voltage regulation limits DC include DC Output ripple & noise. LOAD +3.3V +5V +12V1 +12V2 -12V -5V +5VSB Condition_1 X X X X X X 2.5A Condition _2 0.2A 0.2A 0.1A 0.5A 0A 0A 0A Condition _3 0.3A 0.2A 1A 0.5A 0.5A 0A 0.05A Condition _4 0.5A 3A 15A 12.5A 0A 0A 0.5A Condition _5 0.1A 15A 2A 2A 0A 0.3A 0.5A Condition _6 1A 20A 10A 9A 0.5A 0A 2.
4.4. OUTPUT RISE TIME (10% TO 95% OF FINAL OUTPUT VALUE, @ FULL LOAD) 115V-rms or 230V-rms + 3.3Vdc : 20ms Maximum + 5Vdc : 20ms Maximum + 12Vdc : 20ms Maximum + 5Vsb : 20ms Maximum - 12Vdc : 20ms Maximum - 5Vdc : 20ms Maximum 4.5. OVER VOLTAGE PROTECTION Voltage Source +3.3V +5V +12V Protection Point 3.76V-4.8V 5.6V-7.0V 13.0V-16.5V 4.6. OVER CURRENT PROTECTION Output Voltage +3.3V +5V +12V1 +12V2 Max. over current limit 60A 48A 25A 30A 4.7.
4.8. POWER SIGNAL POWER GOOD @115/230V, FULL LOAD POWER FAIL @115/230V, FULL LOAD 100 –500mSec. 1 mSec. minimum Figure: T1: Power-on time shall be less than 500 ms (T1 < 500 ms). T2: Rise time : 0.1 ms to 20 ms (0.1 ms ≤ T2 ≤ 20 ms). T3: Power-ok delay time: 100 ms < T3 < 500 ms T4: Power-ok rise time: T4 ≦ 1 ms T5 + T6: AC loss to PWR_OK hold-up time :T5 + T6 ≥ 17 ms 4.9. The main power supply shall be off when the PS_ON pin is floating (open collector).
6.1. TEMPERATURE RANGE Operating +10 to +50 deg. C Storage -20 to +80 deg. C Operating 5 –95% RH, Non-condensing Storage 5 –95% RH, Non-condensing 6.2. HUMIDITY 6.3. VIBRATION The subject power supply will withstand the following imposed conditions without experiencing non-recoverable failure or deviation from specified output characteristics. Vibration Operating – Sine wave excited, 0.25 G maximum acceleration, 10-250 Hz swept at one octave / min.
6.7. INSULATION RESISTANCE Primary to Frame Ground : 20 Meg.ohms Minimum Primary to Secondary : 20 Meg.ohms Minimum 7. LABELLING Label marking will be permanent, legible and complied with all agency requirements. 7.1. MODEL NUMBER LABEL Labels will be affixed to the sides of the power supply showing the following: - Manufacturer’s name and logo. - Model no., serial no., revision level, location of manufacturer. - The total power output and the maximum load for each output. - AC input rating. 8.
MECHANICAL DRAWING OAD10029937 Released Date:2010/5/18-16:2:35
1/1禁禁禁禁禁禁 文文文文文文 文文文文文文 文文文文文文 OAD10029937-R1.
