Datasheet

ManualsBrandsFSP FORTRON ManualsPower Supply UnitsIndustrial PC PSU 350 W 80 PLUS Bronze

SPECIFICATION

ESD11001280

Released Date:2011/07/14-09:18:54

FSP350-70PFL

Summary of content (11 pages)

PAGE 1
SPECIFICATION ESD11001280 FSP350-70PFL Released Date:2011/07/14-09:18:54
PAGE 2
1/10禁止翻印外洩文件資料管制文件資料管制文件資料管制台灣桃園市建國東路 22 號 NO.22,Jianguo E, Rd.,Taoyuan City,Taiwan,R.O.C. TEL:+886-3-375-9888 FAX:+886-3-375-6966 SPECIFICATION FSP350-70PFL Main Feature: Active PFC Circuit Full Range Input JAN 31,2011 REV: 1.3 ESD11001280-R6.
PAGE 3
文件資料管制文件資料管制文件資料管制 MODEL: FSP350-70PFL Revision History Rev Description Date Author 1.1 Update 4.1.1. OUTPUT RATING & 4.2. OUTPUT TRANSIENT LOAD RESPONSE 1.12.2011 Karl 1.2 Update 4.3.3. INRUSH CURRENT 1.20.2011 Karl 1.3 Update 4.1.1. OUTPUT RATING 1.31.2011 Karl 2/10禁止翻印外洩 2 ESD11001280-R6.
PAGE 4
文件資料管制文件資料管制文件資料管制 1. GENERAL DESCRIPTION AND SCOPE This is the specification of Model FSP350-70PFL; AC-line powered switching power supply with active PFC (Power Factor Correction) circuit, meet EN61000-3-2 and with Full Range Input features. Designed and manufactured by FSP GROUP. The 5Vsb power is less than 1Winput at power off mode (PS_ON input at high state) which is comply with EuP Lot 6 year 2010 requirement.
PAGE 5
文件資料管制文件資料管制文件資料管制 Output 1 2 3 4 5 6 Nominal +3.3V +5V +12V1 +12V2 -12V +5VSB Regulation ±5% ±5% ±5% ±5% ±10% ±5% Ripple/Noise 50mV 50mV 120mV 120mV 150mV 50mV Min 0.5A 0.5A 0.5A 0.5A 0A 0.1 A Max 21.0 A 16.0 A 17.0 A 17.0 A 0.5 A 3A 7 -5V ±10% 100mV 0A 0.3A peak 3.5A *-5V Option, +5vsb peak <= 10ms. (1) The +3.3V and +5V total output shall not exceed 105watts. (2)total output for this subject power supply is 350 watts.
PAGE 6
文件資料管制文件資料管制文件資料管制 115V-rms or 230V-rms + 5Vdc : 20ms Maximum 4.1.5.OVER VOLTAGE PROTECTION Voltage Source + 3.3 Vdc +5Vdc Protection Point 3.7V-4.8V 5.7V-7.0V +12Vdc AND +12Vdc 13.3V – 16V 4.1.6.SHORT CIRCUIT PROTECTION Output short circuit is defined to be a short circuit load of less than 0.1 ohm. In the event of an output short circuit condition on +3.3V, +5V or +12V or output, the power supply will shutdown and latch off without damage to the power supply.
PAGE 7
文件資料管制文件資料管制文件資料管制 POWER GOOD @ 115/230V,FULL LOAD POWER FAIL @115/230V, FULL LOAD PS_ON 100 –500mSec. 1 mSec. minimum ON OFF P.G. SENSE LEVEL 95% Main O/P P.G. T1 T1 < 20mS T2 = 100~500mS T3 > 1mS T2 T3 4.2. OUTPUT TRANSIENT LOAD RESPONSE +5V and +12V must be within specification for a step change in current as specified below. The outputs will be tested one section at a time with all other sections at maximum load. The test transition will be from IA to IB and IB to IA.
PAGE 8
文件資料管制文件資料管制文件資料管制 IA: IB: 21.0 amps 14.7 amps Volts variation: 400 mV max (p-p) Setting time: 10 ms max +12V1/0.5A,+12V2/0.5A,+5V/2A, -12V/0.1A,+5VSB/0.1A IA IB 10ms 10ms 4.2.1 Transient Load Requirement Output +3.3V +5V +12V1,+12V2 △Step Load Size 30% of max load 30% of max load 30% of max load Load Slew Rate 0.5 A/μs 0.5 A/μs 1.0 A/μs Capacitive Load 6000μF 6000μF 4700μF 4.3. INPUT ELECTRICAL SPECIFICATIONS 4.3.1. VOLTAGE RANGE PARAMETER V-in Range UNITS V-rms 90 - 264 4.3.2.
PAGE 9
文件資料管制文件資料管制文件資料管制 4.4. EFFICIENCY Full load (100%) 82% 115VAC Typical load (50%) 85% Light load (20%) 82% (loading shown in Amps) Loading +12V1 +12V2 +5V +3.3V -12V +5Vsb Full (100%) 11.14 11.14 7.38 9.68 0.33 1.97 Typical (50%) Light (20%) 5.57 2.23 5.57 2.23 3.69 1.48 4.84 1.94 0.16 0.07 0.98 0.39 4.5. Standby Power Consumption (5Vsb): Input Power < 1W @ 5Vsb/100mA & 230Vac input PS_ON input signal @ High State 4.6.
PAGE 10
文件資料管制文件資料管制文件資料管制 Environmental conditions. 5.1. TEMPERATURE RANGE Operating Storage 350W 0 to +50 deg. C -20 to +80 deg. C Operating Storage 5 –85% RH, Non-condensing 5 –95% RH, Non-condensing 5.2. HUMIDITY 5.3. VIBRATION The subject power supply will withstand the following imposed conditions without experiencing non-recoverable failure or deviation from specified output characteristics. Vibration Operating – Sine wave excited, 0.25 G maximum acceleration, 10-250 Hz swept at one octave / min.
PAGE 11
文件資料管制文件資料管制文件資料管制 The subject power suppy will meet FCC and CISPR 22 requirements under normal load conditions. 8. LABELLING Label marking will be permanent, legible and complied with all agency requirements. 8.1. MODEL NUMBER LABEL Labels will be affixed to the sides of the power supply showing the following: - Manufacturer’s name and logo. - Model no., serial no., revision level, location of manufacturer. - The total power output and the maximum load for each output. - AC input rating. 8.2.