MAX S202E
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to “dangerous voltage” and to prevent from a risk of electric shock. Warning: To reduce the risk of electric shock, don’t open the cabinet. Refer servicing to qualified personnel only. The exclamation point within an equilateral triangle is intended to alert the user to important operating and maintenance (servicing). Please read the manual carefully before installing the receiver.
QUICK INSTALLATION GUIDE QUICK INSTALLATION GUIDE FOLLOW NEXT STEPS FOR THE CORRECT INSTALLATION OF THIS RECEIVER. STEP 1: CONNECTIONS Example 1 – Basic System rev 1.0 Example 2 – DISEqC switches Example 3 – Combined with terrestrial PAG. 3 Example 4 – Motorized system ENGLISH The coaxial cable, with satellite signal, must be connected to the “IF IN” connector. The “TV SCART” connector must be connector to the TV set. The receiver also includes an UHF modulator, allowing connecting a TV set or VCR.
QUICK INSTALLATION GUIDE STEP 2: BASIC CONFIGURATION OF THE RECEIVER Language: press [ ] to select languages. The selection of languages include: English, German, French, Spanish, Italian, Portuguese, Turkish, Polish, Russian, Danish, Greek, Hungarian, Arabic, Farsi. First Audio: Some channels offer more than one audio language. This function allows you to set the preferred audio language for those channels using [ ].
QUICK INSTALLATION GUIDE recommend you to contact your installer or to refer to the user manual of this system to get the correct information. Single search: You can edit the following items (Image 2): IMAGE 3 PAG. 5 ENGLISH rev 1.0 IMAGE 2 1. Satellite: Press [ ] to switch Satellites or press [OK] to enter satellite list to select directly. 2. LNB Configuration: Selecting this option and pressing [OK], the LNB Configuration menu will be displayed.
QUICK INSTALLATION GUIDE ENGLISH IMAGE 4 Multi search: You can edit the following items (Image 4): 1. On “Satellite” item press [OK] to open the satellite list. Then press [ ] to move the highlight and press [OK] to mark/unmark and [EXIT] to finish the selection. You can select several satellites in this menu. At the bottom of the screen you can see the selected satellites. The system will use DiSEqC1.0/1.1, DiSEqC1.2 and USALS functions to search the marked satellites and scan channels. 2.
QUICK INSTALLATION GUIDE GMT has to be turned off. NOTE: If the current channel provides the correct time information, you will see the current time after you entered “Time” menu. If the channel doesn’t provide time information, you have to input the date and time information manually. The most channels support the time signal. 5. Show time: Use [ ] to switch on/off this option. When the option is enabled, the time will be displayed at the TV in a frame in the top right margin. 6.
QUICK INSTALLATION GUIDE TV Channel List: This option shows the list of TV stored channels. Radio Channel List: This option shows the list of Radio stored channels. Channel Setup: This option allows setting the receiver to start in a predefined channel. Delete All: This option deletes all TV and Radio stored channels. Restore channel list and settings: This option loads the user TV and Radio channel list, saved previously.
QUICK INSTALLATION GUIDE Language: This option allows choosing the language of the menus. TV System: This option allows choosing the video Standard and other parameters of the screen. Time & Timer Setting: Timer setting menu. OSD Setting: This option allows configuring the subtitles of the channel information. Power setting: Turns on or off the LNB power. RCU position Switch: To chose the RCU position of the remote control. Information: Shows all the technical information for the selected channel.
Safety Precaution Caution…..…………………...............................………………………………………………13 1. Panel & Remote Control Description 1.1. Front Panel Description…….......................................…………………………14 1.2. Rear Panel Description……................................………….…………………..14 1.3. Remote Control Description…...............................................…………………………..15 2. Basic Operations 2.0. Switch on STB……………………….....................................………………………………...16 2.1. Standby ……………………..........
INDEX rev 1.0 PAG. 11 ENGLISH 3.1.4.4 Edit..........................…………………...………………………...24 3.1.5. Find…………….........................……………………..……..………………..…….24 3.2. Radio Channel List……..................................……………………………………......25 3.3 Channel Setup…………..................................………………………………......25 3.3.1. Start-up Channel……………................................……………………………......25 3.3.2. Channel Play Type………........................…………………………………......25 3.4. Favourite Channel List Name…….
7. DVR Management 7.1. Media management.............................................................................................42 7.1.1. Recording management.............................................................................43 7.1.1.1. How to reproduce a recording..................…………..……………43 7.1.1.2. How to rename a recording.................……………………………43 7.1.1.3. How to block a recording………….........…………………………43 7.1.1.4. How to delete a recording..................……………………………43 7.1.1.5.
SAFETY PRECAUTION Warning: To reduce the risk of electric shock, don’t open the cabinet. Refer servicing to qualified personnel only. The exclamation point within an equilateral triangle is intended to alert the user to important operating and maintenance (servicing). Please read the manual carefully before installing the receiver. Caution: Never open the device by yourself. Dangerously high voltages are present inside the unit. Refer servicing to qualified staff only.
PANEL & REMOTE CONTROL DESCRIPTION 1. PANEL & REMOTE CONTROL DESCRIPTION 1 2 3 4 5 6 1. POWER: Switches the receiver on, or enters standby mode. To completely switch off the receiver, you have to use the switch on the back of the receiver. 2. LOCK LED: Indicates a sufficient signal level at the IF IN input. 3. DISPLAY: 4 Digits to display the program numbers. 4. IR-SENSOR: Reception sensor for the IR remote control signals. 5.
PANEL & REMOTE CONTROL DESCRIPTION 1 3 6 8 10 16 17 19 22 21 26 25 29 30 33 7 9 12 11 13 15 18 20 23 24 27 28 31 32 34 35 ■ rev 1.0 ■ PAG. 15 ENGLISH 14 2 4 5 1.- POWER: Switches receiver ON or in stand-by-mode. 2.- LEDs: Shines as function control, showing the selected transmission code 1, 2 or 3. 3.- TV/R: Switches between TV and Radio channels. 4.- CODE: Changes transmission code of the remote control. 5.- MUTE: Switches audio on and off. 6.- NUMERIC KEYS: For direct typing values and names.
BASIC OPERATIONS 2. BASIC OPERATIONS 2.0. SWITCH ON STB Switch the [Device’s Main Power] switch on. When the STB is first used it will display the quick setup page where the receiver can be configured quickly. For further use the STB will play the same channel as last time when it was switched off.
BASIC OPERATIONS 2.3. MUTE OSD 2 1. Press the [Mute] button to mute the sound. On the screen an icon will be displayed to indicate the muted sound (OSD 2). 2. Press the [Mute] button again to restore the sound. 2.4. CHANNEL NUMBER In TV mode you can enter the channel number directly with your remote control unit and confirm the number with the OK button to change to the desired channel. In TV mode, press [0] button to enter the Multi-Picture mode (OSD 3). 1.
BASIC OPERATIONS OSD 4 OSD 5 OSD 6 In TV mode press [OK] button to open the Channel List window. Reduced Channel List (OSD 4): ] keys to navigate this list. You can use [ 1. Press [Yellow] button to open the SAT list. After selecting a satellite the channel list will be reduced to the channels of this satellite. 2. Press [Blue] button to open the “Find” window. You can use this feature to find channel by their names. 3. Press [Red] button to open the expanded channel list. 4.
BASIC OPERATIONS and date of this event. (To program a recording, the event does not have to be started). 4. To close the EPG menu press [Exit]. 2.14. LIST In TV mode, press [List] button to access directly to the “TV Channel List” menu or to the “Radio Channel List” menu. 2.15. FAVOURITES OSD 9 ? FREQUENTLY ASKED QUESTION Q: Why the screen displays “No Favourite Channel” after pressing the [Favourite] button? A: No channels have been assigned to a Favourite Group yet.
BASIC OPERATIONS 2.21. LNB SHORT When LNB is short, it will notify user on screen “LNB Short!” (OSD 14). Please check your cables and connections for shorts. When the short is removed the warning message will disappear. OSD 14 2.22 CODE It shows and changes the selected code on the remote control. This code has to correspond with the one selected on the receiver’s menu. (Chapter 5.7) ENGLISH 2.23. REC To start the recording (OSD 15).
BASIC OPERATIONS In order to stop a recording before the ending of the programmed length, press the [Stop]-Key. A new window will be shown in order to confirm the end of the recording (OSD 16). If you press the Key [Rec], the recording will continue. Press the key [Stop] again to end the recording manually, if you want to end the recording before the programmed length. 2.24. PVR OSD 16 It opens directly the recording administration menu (Chapter 7.1). 2.25. TIME SHIFT ■ ■ OSD 17 ■ 2.26.
CHANNEL 3. CHANNEL ENGLISH OSD 20 Press [Menu] in the TV mode to enter the main menu (OSD 20). ] to select the Channel item. 1. Press [ 2. Press [OK] to enter the selected item. In the Channel menu (OSD 21): 3. Press [ ] to select the wanted menu item. 4. Press [OK] to enter the selected item among. - TV Channel List - Radio Channel List - Channel setup - Favourite channel list name - Delete All - Restore channel list and settings - Save channel list and settings 3.1.
CHANNEL 3.1.2. MOVE OSD 24 1. To move/change channels: Pushing the [Red] button, you will see a picture like OSD 24. You will be able to move or change the position of the channels: - Push again the [Red] button to move the channel. - Push the [Green] button to change the position of the channel. 2. Move the channel to the desired position with [ ]. Press [OK] to confirm the position. OSD 25 1. Press [Green] to open the Sort window (OSD 25). Press [ ] to select and [OK] to confirm your choice. 2.
CHANNEL this menu. OSD 30 3.1.4.3 LOCK In Channel Edit menu, press [Yellow] button to place a Lock icon behind the name of the highlighted channel. Marked channels (OSD 30) will be locked and displayed only after password has been entered if you confirm to save the changes when you leave this menu. OSD 31 OSD 32 OSD 33 Pressing the [Blue] button in the TV Channel List Edit menu will open another window where you can choose between Edit the actual channel or create a new channel (OSD 31). 1.
CHANNEL 3.2. RADIO CHANNEL LIST Basically the operation of “Radio Channel List” is same as “TV Channel List”, except that in the small channel window the Fte Logo will be displayed (OSD 35). 3.3. CHANNEL SETUP OSD 35 When you enter the “Channel Setup” menu you will see a screen like beside (OSD 36): OSD 36 Press [OK] to enter “Start-up Channel” menu to see the screen like showed beside (OSD 37): 1. If you set of “Boot on Channel” to “On” you can edit the following two items.
CHANNEL 2. After entering the password correct a safety question will show up where you have to confirm first (OSD 41). 3. Select “Yes” to delete all channels or “No” to cancel and confirm with [OK]. 4. In step 2 and step 3, pressing [Exit] will exit the function directly without saving. ENGLISH OSD 40 ? FREQUENTLY ASKED QUESTION Q: IF I incautiously delete all channels, what should I do? A: There are three ways to restore: - To re-search all channels at the “Installation” menu.
INSTALLATION 4. INSTALLATION OSD 44 4.1. SINGLE SEARCH OSD 45 rev 1.0 OSD 46 After selecting Antenna Setup another window will be opened (OSD 46). You can edit the following items: 1. Satellite: Press [ ] to switch Satellites or press [OK] to enter satellite list to select directly. 2. LNB Configuration: Selecting this option and pressing [OK], the LNB Configuration menu will be displayed (OSD 47).
INSTALLATION ENGLISH OSD 48 3. DiSEqC1.0: Use [ ] to switch the options of DiSEqC switches. 4. On “TP Index” item use [ ] to select the desired transponder. 5. In the “FTA Only” item, press [ ] to select to scan only free channels or even scrambled channels. If you select “Yes” it will scan free channels only. 6. In “Scan Channel” item, press [ ] to select to scan TV + Radio Channels, or just TV channels or just Radio channels. 7.
INSTALLATION 4.3. TP SCAN OSD 52 rev 1.0 OSD 54 OSD 55 PAG. 29 ENGLISH OSD 53 When you enter “TP Scan” menu a window like the one beside will be displayed (OSD 52): ] to select the satellite 1. On “Satellite” item, press [ you want to scan or press [OK] to open the satellite list for selection. 2. On “TP Index” item use [ ] to select the desired transponder.
INSTALLATION will search the selected TP. In case you select “On”, the NIT (Network Identification) will be identified and the receiver will automatically search all the TP of this network. 6. Press [OK] to start scanning. 7. On the “TP Scan” item, press [Exit] to cancel the scanning and saving the found channels. 4.4. SATELLITE LIST OSD 57 OSD 58 OSD 59 OSD 60 When you enter the “Satellite List” menu you can see a window like the one beside (OSD 56): ] and mark/ 1.
SYSTEM SETUP 4.6. SATELLITE GUIDE OSD 61 OSD 62 rev 1.0 OSD 63 OSD 64 PAG. 31 ENGLISH When you enter “Satellite Guide” menu, you will see the screen like beside (OSD 63). Here you can enter your local longitude and latitude and the satellite’s longitude. The receiver calculates the antenna’s azimuth and elevation to point your antenna to the selected satellite. 1. Use the [Number] buttons to input the values of “Local Longitude”, “Local Latitude” and “Satellite Longitude”. 2.
SYSTEM SETUP 5. SYSTEM SETUP ENGLISH OSD 65 Press [Menu] in the TV mode to enter the main menu (OSD 65). ] to select the System Setup item. 1. Press [ 2. Press [OK] to enter the selected item. In the System Setup menu (OSD 66): 3. Press [ ] to select the wanted menu item. 4. Press [OK] to enter the selected item among. - Language - TV System - Time & Timer Setting - OSD Setting - Parental Lock - Power setting - RCU Position Switch 5.1. LANGUAGE OSD 67 5.2.
SYSTEM SETUP OSD 69 5.3. TIME & TIMER SETTING When you enter “Time” “Local Time Setting” or “Sleep Timer” a menu with three items will be opened (OSD 69). Use [ ] to select between the three options and confirm with [OK]. 5.3.1. TIMER rev 1.0 OSD 70 OSD 71 Select “Timer” item and press [OK] to enter the “Timer list” menu (OSD 70). The current time will be displayed in the first column. If the current time is incorrect, please modify it with the [Number] buttons at the “Time” menu.
OSD 72 OSD 73 date. - On time: Introduce BY using the numerical keys on the remote control; the time when you want to start recording. By default, when you enter this option, it shows the current time. - Length: Settle the length of time you want the receiver to record a channel. Once it is finished, the receiver will be settled in Stand-By. Note: If the date/ start time is prior to the current date/hour, a warning message will be shown and you have to change the date/start time.
SYSTEM SETUP Note: If the date/ start time is prior to the current date/hour, a warning message will be shown and you have to change the date/start time. 7. Press [Exit] to leave the “Timer” menu. Note: If the receiver is in stand-by, and Low Power Consumption mode is active, the receiver will switch on 1 minute before the programmed event. 5.3.2. LOCAL TIME SETTING OSD 74 OSD 76 5.3.3. SLEEP TIMER Press [OK] button in this option to set the sleep timer.
SYSTEM SETUP Press [ ] to set the time between 1 to 10 seconds. 3. Position: To define the position of the information’s bar (top/bottom). 4. OSD Transparency: With this parameter you can set the transparency of the menus. Press [ ] select the value between 10%, 20%, 30%, and 40% and “NO” (means no transparency function). 5. Load OSD Setting Default: If you want to reset your OSD settings to the default settings then select this item and press [OK]. 6. Press [Exit] button to leave the “OSD Setting” menu.
SYSTEM SETUP OSD 80 5.7. RCU POSITION SWITCH In order to avoid interferences between remote controls, you have the possibility to change the code of it, to do that you have to change the position of a switch in the remote control. But first of all you have to change this code in the receiver. You can do this in the menu “RCU Position” (OSD 80). You have to select the same position in the receiver than in the remote control (OSD 81). rev 1.0 OSD 81 PAG. 37 ENGLISH 1.
TOOLS 6. TOOLS ENGLISH OSD 82 Press [Menu] in the TV mode to enter the main menu (OSD 82). ] to select the Tools item. 1. Press [ 2. Press [OK] to enter the selected item. In the Tools menu (OSD 83): 3. Press [ ] to select the wanted menu item. 4. Press [OK] to enter the selected item among. - Information - Quick Setup - Game - Factory Default - Software Upgrade - SatcoDX Auto Programing - Smartcard 6.1. INFORMATION OSD 83 1.
TOOLS 6.3. GAME When you enter “Game” menu, you will see three Games include Tetris, Snake and Othello (OSD 86). 6.3.1. TETRIS OSD 86 6.3.2. SNAKE 1. Mark “Setup” and press [ ] to select the level (speed). 2. Mark “Start” and press [OK] to start the game. 3. Mark “Cancel” and press [OK] to leave the game. 4. Play the game: - Press [ ] to guide the snake to the red blocks. Every block you ate increases the length of the snake. If the snake runs against a wall or against itself then it dies.
TOOLS 6.5. SOFTWARE UPGRADE There are three ways of upgrading the software of the receiver as you can see at OSD 88. 6.5.1. RS232 UPGRADE ENGLISH OSD 88 OSD 89 OSD 90 1. This function allows you to upgrade the software of the receiver. This can be done from PC to receiver or from a master receiver to a slave receiver. 2. Connect master receiver or PC to the slave receiver via serial interface (0-Modem cable).
TOOLS OSD 92 For further information about the upgrading of the receivers, please visit http://www.ftemaximal.com, in the chapter about upgrading receivers. OSD 93 OSD 94 6.6. SATCODX AUTO PROGRAMMING This function is using the tables of the SatcoDX websites to update your channel and satellite lists. 1. Start the SatcoDX application on your PC. 2. Select “SatcoDX Auto Programming” item from the “Tools” menu and press [OK]. The screen will show the message “OK to Proceed” (OSD 93). 3.
DVR MANAGEMENT 7. MEDIA MANAGEMENT ENGLISH OSD 96 Press the key [Menu] on the remote control to go to the main menu (OSD 96). ] to settle the 1. Press the arrows on the remote control [ option of DVR management. 2. Press [Ok] to enter the submenu DVR Management In the submenu DVR management (OSD 97): 3. Press the keys on the remote control [ ] to move to the different options on the menu. 4. Press [Ok] to go to the selected option on the submenu.
DVR MANAGEMENT 7.1.1. RECORD MANAGEMENT - RECORD LIST With this option of the menu, you can reproduce, rename, block and delete recordings. You can go to this option using the menu or directly pressing the key [PVR] on the remote control. Information on the window (OSD 98): OSD 99 7.1.1.1. HOW TO REPRODUCE A RECORDING 7.1.1.2. HOW TO RENAME A RECORDING OSD 100 Press the key [Red] to rename a recording. - A window will appear where you can change the name of the record (OSD 99).
DVR MANAGEMENT 7.1.1.5. HOW TO DELETE ALL THE RECORDINGS OSD 103 To delete all of the recordings, press the [Blue] key. - A window appears and asks for the password to delete all the recordings. If it has not been modified, it is by default the code “0000”. - A mark will appear on the names of the channels (OSD 102). - The marked recordings will be deleted once you confirmed that you want to save the changes by leaving the menu. ENGLISH 7.1.2.
DVR MANAGEMENT - RENAME 1. Press the [Red] button to rename the file. 2. A new window appears where you can change the name of the recording moving through cursors. Press OK to exit and modify the name. 3. Once the change is done, i will be not modified until you do not exit from the list. 4. Press the [Menu] button to exit. A new window will request information to save the changes. OSD 107 -DELETE -MOVE 1. Press the [Yellow] button to move the file. 2.
DVR MANAGEMENT Press [OK] to confirm the characters. (OSD 110) 2. After writing down the characters, select OK and press [OK] on the remote control. 7.1.2.4. LOGO OSD 111 *Only available for the picture list of the Hard Disk. Press the [Yellow] button over the picture you want it to appear as background when you are listening to the radio or the Audio playlist. ENGLISH To restore the Fte logo background, delete the picture of the Hard Disk or disconnect it from the Receiver. 7.1.2.5.
DVR MANAGEMENT You can rotate the picture with the buttons [ 113) ]. (OSD 7.1.2.8. VIDEO .MPG PLAYER OSD 114 1. Press the button [OK] over a .MPG video or a list of .MPG videos. 2. The file will be played on the screen. In case that you play a playlist, it will play all the files one by one. (OSD 114) 7.2.- HDD CONTROL 7.2.1. TMS RESERVED SIZE Reserved Size for the storage of the Time Shifting. The available options can vary depending on the capacity of the external Hard Disk. 7.2.2.
DVR MANAGEMENT 7.2.6. FORMAT DISK This option will format the hard disk, erasing it completely. When you select this option, a window appears and asks for a password to format the hard disk. If it has not been modified, it is by default the code “0000”. Once this code is given, the hard disk will be formatted and you will lose all the saved recordings. Note: This process is irreversible. Once you have selected this option and you have given the password, the data will be lost. OSD 116 ENGLISH 7.3.
TECHNICAL SPECIFICATION 8.
CONFORMITY DECLARATION “WE , FTE MAXIMAL, DECLARE THAT THE PRODUCTS IS IN CONFORMITY WITH FOLLOWING DIRECTIVES LOW VOLTAGE DIRECTIVE 2006/95/EC EMC DIRECTIVE 2004/108/EC” rev 1.0 ENGLISH MAX S202E PAG.
