User`s manual

ManualsBrandsFte maximal ManualsNetworkingTSQ 310

User’s manual · TSQ 310

- 1 - TSQ 310 version_en_1.1 FTE maximal

NOTE:

This user’s guide is adapted to software version 000A/0003 of TSQ 310 dated

18/10/2010.

For future software updates, you can download the user’s guide from the following website:

http://www.ftemaximal.com/

Chapter 1. Installation.

1.1. Safety Measures

1.- Never place the device next to hot sources.

2.- Never undergo the device to temperatures that exceed its level of operation.

3.- Never expose the device to leakings nor spatterings.

4.- Never place objects that contain liquids over the device.

5.- Respect the ventilation slots of the device, do not cover them with any kind of object.

6.- The space around the device must be free of objects, in a minimum radius of 40cm.

7.- Avoid locations with possibilities of spilling liquids on the inside of the device, and with important changes of

temperature.

8.- Never open the device by yourself due to electric risk. In case of problems, go always to qualified technicians

9.- Never, under no circumstances, open the device when connected to the electrical net..

10.- During the handling it is better to disconnect the device from the electrical net.

11.- Obey the electricity security rules during the assembling. Use materials that obey the current law.

12.- The connecting plug must be accessible in a fast and simple way to have a fast disconnection.

13.- Never touch the plug with wet hands. Also, disconnect always the device before handling the connections.

14.- Never put any heavy object over the device, since it could get damaged.

15.- If the device is going to remain some time without use, it is recommendable to disconnect it from the electrical net.

16.- The repairmen and the maintenance of the device must be done by TV and radio specialised technicians.

1.2. Box content

Quick installation guide 2 x Bridge F male – F male DC Cable

TSQ 310 Cable 12 cm PIN to PIN RJ45 – RJ45

Summary of content (16 pages)

PAGE 1
User’s manual · TSQ 310 NOTE: This user’s guide is adapted to software version 000A/0003 of TSQ 310 dated 18/10/2010. For future software updates, you can download the user’s guide from the following website: http://www.ftemaximal.com/ Chapter 1. Installation. 1.1. Safety Measures 1.- Never place the device next to hot sources. 2.- Never undergo the device to temperatures that exceed its level of operation. 3.- Never expose the device to leakings nor spatterings. 4.
PAGE 2
User’s manual · TSQ 310 1.3. Description and connections The module TSQ 310 is used for the reception of free channels that obey the DVB-S / DVB-S2 standards. Each module allows the reception of a complete transponder in DVB-S (QPSK) / DVB-S2 (QPSK/8PSK), and the subsequent modulation in DVB-C (QAM) of it. A feature of this equipment is its modulator in Vestigial Side Band (or VSB). This modulation can be used to distribute adjacent channels in one distribution without any intermodulation problem.
PAGE 3
User’s manual · TSQ 310 Stages of transmodulator TSQ 310 Input Selection of a tuned satellite transponder Transmodulation The tuned channels of the transponder are modulated according to the DVB-C rules. If the transponder has encoded channels, the final user will need a receiver with CI+ subscriber card or an encrypted channels receiver. Out Configuration of the channels and output parameters 1.4. Programming TSQ 310 has two ethernet connectors.
PAGE 4
User’s manual · TSQ 310 1.4.2. Programming Below you will find the steps to follow in order to make the programming both from corresponding EVO and MINI field strength meter as well as from PRO 201. mediaMAX EVO / mediaMAX MINI In order to start programming the TSQ 310 transmodulator, you will have to go to “Tools” option through the key 8 of your field strength meter and to select the “Prog Transmodulators “option. Then, it will proceed to recognize the module and to show the main menu. In the “Prog.
PAGE 5
User’s manual · TSQ 310 2. State of the module In the option “State of the module” are specified the main parameters of the module at this moment. - Transmodulator input: It indicates whether the module is hooked or without signal. - Input bit rate: Transfers of data in the satellite tuner input. - Output bit rate: Transfer of data in the module output. - BER before and after Viterbi: It indicates the error rate of bits of the input signal before and after the correction produced by Viterbi algorithm.
PAGE 6
User’s manual · TSQ 310 4. Modulator configuration This option allows you to configure the DVB-C modulator that the device has. - Symbol speed: The available symbol speed ranges from 1 to 6.96 MS/s. In order to estimate the output symbol speed you have to take into account the following parameters: input modulation, input symbol speed, input FEC, output modulation.
PAGE 7
User’s manual · TSQ 310 6. System This option provides information of the transmodulator. - System logfile: In this field are indicated the registered events in the module. - Read log: It allows reading the registered events in the module. - Clear log: It allows deleting all events stored until this moment. - Export log to USB: It allows you to export all events registered to the connected USB device.
PAGE 8
User’s manual · TSQ 310 - Configure all devices: - Input values to all devices: It allows copying the current input configuration in all the interconnected modules. - Modulator values to all devices: It allows copying the configuration of the current modulator in all the interconnected modules. - Output values to all devices: It allows copying the current output configuration in all the interconnected modules.
PAGE 9
User’s manual · TSQ 310 Adding services: 1. Select “Service to add” option 2. Select one of the transponder services you want to add. 3. Once you have chosen the service, select the “Add/Remove” button to include the service in the multiplex. Note: It is not recommended to exceed the 85% of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services.
PAGE 10
User’s manual · TSQ 310 - Remove all services: It allows removing all the services included in the multiplex. - Modify LCN: The LNC function allows assigning automatically a predetermined position to each one of the services of the multiplex. This function will allow the users who have a receiver with LNC support to make the ordination of channels automatically.
PAGE 11
User’s manual · TSQ 310 Next it is attached the identification table (NID/ONID) of the main satellites. You will be able to find more information in the law ETSI TR 101 162 v1.2.1. Satellite Hotbird 13ºE (Eutelsat 13ºE) Astra 19.
PAGE 12
User’s manual · TSQ 310 Cable modulator ( Out Cable) This option allows you to configure the DVB-C modulator that the device has. TSQ 310 * Out Cable Modulacion: 64 >Roll-off: 1.5 Symbol speed: 1000 - Spectrum inversion: Activate or deactivate the spectrum inversion in the modulation. - Modulation: Modulation Format. Options: 16 QAM, 32 QAM, 64 QAM, 128 QAM, 256 QAM.
PAGE 13
User’s manual · TSQ 310 - Read from module: It stores the current configuration of the module in the memory of the programmer. The steps to make a correct reading of the headend are specified below: TSQ 310 TSQ 310 TSQ 310 CFG:03 > *Read from Module* *Write to Module * 1. Select the option “Read from module” through Up/Down buttons. Press OK to continue Operation finish Free position 2. Select the position of “CFG” memory where you wish to save the current configuration of the module. 3.
PAGE 14
User’s manual · TSQ 310 - Add Services TSQ 310 BW usage 000% Delete services >Add services TSQ 310 Input 035 % PID:06200 arte HD +Add 1. Select the option “Add services” through Up/Down buttons. Press OK to continue. 2. Select one of the transponder services you want to add, through Left/Right keys and select the “+Add” button to include the service in the multiplex TSQ 310 Operation finish 3. A window will appear and it will let you know that the operation made has been correct.
PAGE 15
User’s manual · TSQ 310 1.5. Accessories and example of installation Example of installation Installation that consist of 6 TSQ 310 and that will allow tuning channels up to 6 different transponders and to distribute them through a network of modulated cable in DVB-C. The distributed channels need a cable receiver in order to be decoded, in this case we propose a PVR C130 CI HDMI receiver that would decode free channels and also encoded channels if we insert a PCMCIA with the corresponding subscriber card.
PAGE 16
User’s manual · TSQ 310 Chapter 2. Technical features Ref.