TWSF 310 CI USER’S MANUAL
User’s manual · TWSF 310 CI NOTE: This user’s guide is adapted to software version v.0.1.37 of TWSF 310 CI dated 04/04/2012. For future software updates, you can download the user’s guide from the following website: http://www.ftemaximal.com/ Chapter 1. Installation. 1.1. Safety Measures 1.- Never place the device next to hot sources. 2.- Never undergo the device to temperatures that exceed its level of operation. 3.- Never expose the device to leakings nor spatterings. 4.
User’s manual · TWSF 310 CI The TWSF 310 CI will be provided with a double DVB-T output that will allow distributing the channels of the tuned transponders in two consecutive multiplex. In order to configure the device we will have two selectable modules. The options of configuration are independent. With the following exceptions: - The output channel of the second module will be set automatically as the consecutive channel after the one configured in the first module.
User’s manual · TWSF 310 CI Stages of transmodulator TWSF 310 CI Input 1 Input 2 Selection of a tuned satellite transponder Transmodulation TP 1 TP 2 The tuned channels of the transponders are modulated according to the DVB-T rules in two multiplex. In cases where the transponder has encoded channels, if you wish to distribute them freely, you will have to link a PCMCIA + subscriber card to each one of the two outputs of the multiplex.
User’s manual · TWSF 310 CI 1.4.2. Programming Below you will find the steps to follow in order to make the programming both from corresponding EVO and MINI field strength meter as well as from PRO 201. mediaMAX EVO / mediaMAX MINI In order to start programming the TWSF 310 CI transmodulator, you will have to go to “Tools” option through the key 8 of your field strength meter and to select the “Transmodulator Prog.“ option. Then, it will proceed to recognize the module and to show the main menu.
User’s manual · TWSF 310 CI 2. Device Status In the option “Device Status” are specified the main parameters of the module at this moment. - Front End: It indicates whether the module is hooked or without signal. - Input bit rate: Transfers of data in the satellite tuner input. - Output bit rate: Transfer of data in the module output. - BER before and after Viterbi: It indicates the error rate of bits of the input signal before and after the correction produced by Viterbi algorithm.
User’s manual · TWSF 310 CI - Modulation: Output modulation format: 4 (QPSK), 16 (16 QAM), 64 (64 QAM). - Advanced settings: - Mode: Selection of the modulation standard: DVB-T and DVB-H. Note: The output useful bits rate will depends on the following parameters: Bandwidth, guard interval, FEC codification and modulation. In the Attachment I you will find all the information related to the resulting useful bit rate in each configuration. 5.
User’s manual · TWSF 310 CI - Settings: This option allows saving and loading the configuration of the module, carrying out firmware update or making an adjustment of the time and date of the module. - Clock: - Set Date and time: Setting of the date and time of transmodulator. It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date.
User’s manual · TWSF 310 CI 7. Program management - New program: This option allows creating a program with the current configuration of a module or group of modules. - Load program: It allows loading a previously created program on a module or group of modules. - Delete program: It allows deleting a program. - Device to process: - Current: The creation or loading of a program will be applied only in the module that is currently connected.
User’s manual · TWSF 310 CI Note: It is not recommended to exceed the 85% of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services. Excessive capacity It is recommended to remove services Recomendad capacity (lower to 85%) Removing services: 1. Select the “Service to remove” option. 2. Select one of the transponder services you want to remove. 3.
User’s manual · TWSF 310 CI - Tables: It allows modifying the value of the following information tables of the DVB, NIT, SDT and PAT services. - Services: - Change service name: It allows changing the name of the service manually. In order to do so, please choose the service in the first line and then write the new name in the second line. Then you have to press “modify” in order to save the changes.
User’s manual · TWSF 310 CI 9. Common Interface This option allows checking the information and configuring the parameters regarding the conditional access. - Selecting Slot: It selects the Slot where the CAM for decoding the services is inserted. - CI Menu: From here you can reach the menu of the card inserted in the CAM. - Decrypted: From this option you can add or remove manually the services that are being decoded by the card.
User’s manual · TWSF 310 CI 1. This field shows the type of parameter that is selected at the moment. Options: Input Sat, Out Terr, Out TV. 2. This field shows the parameter that is selected. In order to move around the different options we have to use the “Up” and “Down” buttons of the keyboard.. Click on OK to edit the selected parameter and Right/Left for changing it. Once it is configured press OK.
User’s manual · TWSF 310 CI Summary table: Satellite input - L.O. frequency - Input Frequency - Symbol Rate - Antenna - Diseqc - Symbol rate auto - DVB Mode Terrestrial output - Modulation - Invert (Spectrum Inversion) - Guard Interval (GI) - Bandwith (BW) - Tx Mode (FFT Mode) - FEC - Mode TV output - RF Channel - RF Level 2. Auto This option allows saving and loading the configuration of the module in the PRO 201 programmer.
User’s manual · TWSF 310 CI - Read log: It allows reading the registered events in the module. TWSF 310 CI LCN >Read LOG file Delete LOG file 1. Select the option “Read LOG file” through Up/Down buttons. Press OK to continue TWSF 310 CI TWSF 310 CI N:00001 Status:03 07/02/11 09:05:02 Front-end lock OK to Show LOG 2. Press OK again to show the log file. 3. A new window will appear. It will show the information about the registered events in the module.
User’s manual · TWSF 310 CI - (1) Change service name: It allows changing the name of the service manually. - (1) LCN: The LNC function allows assigning automatically a predetermined position to each one of the services of the multiplex. This function will allow the users who have a receiver with LNC support to make the ordination of channels automatically. Select a channel through Left/Right buttons and introduce the position. Press the “OK” button and the cursor will be placed over the number.
User’s manual · TWSF 310 CI 1.5. Accessories and example of installation Example of installation Installation that consist of 6 TWSF 310 CI and that will allow tuning channels up to 12 different transponders and to distribute them through a TV network in DVB-T. The TWSF 310 CI with twin output allow distributing up to 12 multiplex in the installation. The distributed channels need a terrestrial receiver in order to be decoded.
User’s manual · TWSF 310 CI Parabolic antenna OS series Mod. OS 100 STB Code 0701105 Chapter 2. Wide band amplifier 47-862MHz Mod. AMP 310 P Code 2003520 Technical features Ref.
User’s manual · TWSF 310 CI ATACHMENT I Depending on the configured parameters we are going to obtain one particular channel capacity (output useful bit rate).
User’s manual · TWSF 310 CI Useful channel capacity (8 MHz) Modulation QPSK 16-QAM 64-QAM FEC codification 1/2 2/3 3/4 5/6 7/8 1/2 2/3 3/4 5/6 7/8 1/2 2/3 3/4 5/6 7/8 Guad Interval 1/4 4.976 6.635 7.465 8.294 8.709 9.953 13.271 14.929 16.588 17.418 14.929 19.906 22.394 24.882 26.126 1/8 5.529 7.373 8.294 9.216 9.676 11.059 14.745 16.588 18.431 19.353 16.588 22.118 24.882 27.647 29.029 1/4 4.354 5.806 6.532 7.257 7.62 8.709 11.612 13.063 14.515 15.24 13.063 17.418 19.595 21.772 22.861 1/8 4.838 6.
ESPAÑA Mogoda, 110 Pol. Industrial Can Salvatella 08210 Barberà del Vallès (Barcelona) España Tel. 00 34 93 729 27 00 Fax. 00 34 93 729 30 73 ftemaximal@ftemaximal.com www.ftemaximal.com FRANCE 16 ZAE Les Mouilles 74570 Groisy Tel. 00 33 450 68 80 17 Fax. 00 33 450 68 84 68 sav@ftemaximal.fr www.ftemaximal.com ITALIA Via Edison, 29 42040 Calerno di Sant’Ilario d’Enza (RE) Tel. 00 39 05 22 90 97 01 Fax. 00 39 05 22 90 97 48 fte@fte.it www.ftemaximal.com DEUTSCHLAND BCN Distribuciones S.A.
