Outlaw Manual.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 2 FTX Outlaw 1/10th Scale RTR 4WD Brushed Electric Powered Off Road Trail Vehicle Congratulations on your purchase of the FTX Outlaw 4x4 Trail vehicle. This 1/10th scale model has been factory assembled and all electrics installed and set up to make it the easiest possible introduction to the sport of driving RC cars.
Outlaw Manual.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 4 Aerial Assembly. Uncoil the aerial wire carefully so as not to kink or knot it in anyway, and first be sure to insert the wire up through the top chassis aerial mount hole from below. Pull the rubber tube cap off the aerial tube and push the wire all the way through the aerial tube until the first 5mm of wire shows out of the other end.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 5 FTX6557W ESC Instructions Features This ESC is setup in a simple way for ease of operation. When switch on it, it automatically searches for the neutral point. When the automatic setup is finished the motor sends out “Do” “Re” “Me” indicating the neutral point is set and it is ready to be operated. The ESC has 2 programmable running modes and a Low voltage protection mode that can be enabled for LiPo batteries. Specification Voltage Input: 7.2V-7.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 6 Etronix Pulse EX2 Sport 2.4GHZ RADIO SET-UP 2 Channel 2.4GHz Steer Wheel Transmitter 1) INTRODUCTION. 6) TRANSMITTER CHARGING. Thank you for choosing this Etronix 2.4GHz radio system, it has been designed for land use but could also suit any 2 channel boat. If you are using this type of product for the very first time, please make sure you read all the information provided before installing in your vehicle.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 7 9) TRANSMITTER FUNCTIONS. A vertical aerial achieves maximum range, so the short 2.4GHz aerial (A) can be folded and rotated to achieve the most vertical position once you are holding the handset comfortably. Then it allows you to fold the aerial away for safe storage.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 8 When at the mid position the model should remain stationary, if it creeps slightly adjust the throttle neutral dial accordingly. should brake (and then reverse if available), otherwise simply flick the Throttle Reverse switch (I) to the “Rev” position. Beneath the folding Control Panel Cover (D) you will find an array of useful adjustments, plus the Power Switch (P).
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 9 12) MATCHING THE RECEIVER TO THE TRANSMITTER. (BINDING) To make sure only one transmitter can control the receiver they need to be matched, and to do so you need to “Bind” them together so they only recognise each others signature code. There is a ‘Bind’ plug included with the receiver, and this is inserted in the third channel (Bind socket) before power is supplied to the receiver for the first time.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 10 Getting Started Switch on transmitter. Hold vehicle clear of the ground, connect battery pack and switch on receiver. Bind the Transmitter and receiver if required. Test the transmitter to check control of the vehicle with wheels off the ground. Start driving slowly and if the vehicle does not go straight, adjust steering trim dial on Transmitter.
Outlaw Manual.qxp_Brushed Oulaw 23/09/2016 16:14 Page 11 Notes: .................................................................................................................................................................. .................................................................................................................................................................. .........................................................................................................................
Outlaw Manual.
