Sideboard Version:05/16/2022 1/16
IMPORTANT INFORMATION! please read the entire manual before starting to assemble and/or using this product.follow the manual thoroughly and keep it for further reference. AVOID SCRATCHES! In order to avoid scratching this furnuture should be assembled on a soft layer-could be a rug. IMPROVE EFFICIENCY ! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time. ANTI-TOPPLE WARNING ! Overturned furniture can cause serious or fatal crush injuries.
Please prepare the following tools When installing, please carefully confirm whether each screw corresponds to the manual, accessories with similar shapes can be distinguished by size A x 44 7 x 35 mm F x 48 B x 44 15 x 9 mm DR x 6 C x 38 DL x 6 6x30 mm I x 20 Jx4 4x14 mm CR x 6 M x 20 6x30 mm Px2 E x 12 4 x 16 mm 4 x 40 mm 3.5 x 12 mm CL x 6 Dx6 Qx2 Rx4 12 x 4 mm Ux4 8 x 30 mm 3/16 N x 28 Ox6 2.5x14 mm Sx1 6 mm Tx2 3.
14 8 16 15 15 16 13 9 13 10 7 11 11 12 11 11 4 3 6 2 5 4/16 1 x6
1 A x 30 Dx6 E x 12 7 x 35 mm 4 x 16 mm Insert quickfit screws (A) to part 1 , as shown. Fix handle (D) to part 1 using bolts (E), as shown. Do not use an electric screwdriver, do not use force during the rotation of the accessories, otherwise it may cause the board to crack A E E A A A x6 E A A D 2 C x 30 4 x 40 mm Attach parts 2, 4 and 5 to part 3 using screws (C), as shown. Slide part 6 into available slot of parts 2, 3 and 4, as shown.
B x 30 3 15 x 9 mm Insert cam locks (B) to parts 2, 4 and 5 and attach part 1, as shown. Turn cam locks clockwise to tighten. B B B B 180° x6 B B DR x 6 F x 24 4 DL x 6 3.5 x 12 mm Fix right inner drawer runner (DR) and left inner drawer runner ( DL) to assembled unit using screws (F), as shown. T F 3.5 x 14 mm DL DR F F 3.
5 F x 24 CL x 6 CR x 6 3.5 x 14 mm Fix left outer drawer runner ( CL) and right outer drawer runner (CR) to parts 7 and 8 using screws (F), as shown. T F 3.5 x 14 mm F F CR F F F CR F F CR F CL FF F F CL F CR F CL CL F 3.5 x 14 mm Fix left outer drawer runner ( CR ) and right outer drawer runner( CL ) to both sides of part 9 using screws (F), as shown.
6 I x 20 Jx4 4 x 14 mm Fix leg supports (J) to part 10 using screws (I), as shown. I I I J J J I I J J 7 Sx1 Ux4 6 mm 8 x 30 mm Fix 11 by rotating clockwise to leg support as shown. Fix 12 to part 10 and adjust feet(S) to leg 12 as shown.
8 Ax8 7 x 35 mm Insert screws (A) into part 7,8,9 as shown.
9 Bx4 Mx4 15 x 9 mm 6x30 mm Insert quickfit screws (A) and wooden dowels (M) to parts 7 and 9, as shown. Insert cam locks into parts 13 &1 6 and attach parts 7 and 9, as shown. Turn cam locks clockwise to tighten.
10 Bx4 15 x 9 mm Mx4 6x30 mm Insert quickfit screws (A) and wooden dowels (M) into parts 9 and 8, as shown. Insert cam locks (B) into parts 13 &16 and attach parts 9 and 8, as shown. Turn cam locks clockwise to tighten.
11 Mx6 Cx6 6x30 mm 4 x 40 mm Insert wooden dowels (M) into assembled unit, as shown. Attach part 10 into assembled unit using screws (C), as shown.
12 Ax6 7 x 35 mm Insert screws (A) into part 14 as shown.
13 Bx6 Mx6 15 x 9 mm 6x30 mm Insert quickfit screws (A) and wooden dowels (M) into part 14, as shown. Add cam locks (B) into assembled unit as shown and attach part 14 to assembled unit. Turn cam locks clockwise to tighten.
N x 28 14 Ox6 2.5x14 mm Fix parts 15 using nails (N) and square washers (O) into assembled unit, as shown. N N N N O N N O N N N N NN N N O N 15 The drawer slides must be aligned with the internal rails, otherwise the drawer will tilt.
Px2 Tx2 Cx2 4 x 40 mm 3.5 x 14 mm 6 x 30 mm Qx2 Rx4 12 x 4 mm For extra stability, it is recommended that you fix your drawer to the wall using the additional hardwares (C, T, R,P and Q), as shown. Should you choose not to affix the product to the wall, serious injury may be caused if the product tips over.
WARRANTY WARRANTY CLAIMS •There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase. •Before making a claim, we may be able to answer your query, simply visit feedbackstation@163.com for further information. Our dedicated After-sale Team will endeavour to answer all messages within 48 hours.
RETURNS CHANGED YOUR MIND AND NEED TO RETURN YOU ITEM? PLEASE FOLLOW THE BELOW INSTRUCTIONS: •If you have purchased and have simply changed your mind, follow the retailer’s instructions for returns. DEFECTIVE ITEMS •If your item is defective in any way, i.e. it doesn’t work but you can’t identify why, in the first instance, please consult our FAQ section at feedbackstation@163.com as there may be a simple solution to the issue.
