Shoe Storage Cabinet Version:12/15/2022 1/21
IMPORTANT INFORMATION! please read the entire manual before starting to assemble and/or using this product.follow the manual thoroughly and keep it for further reference. AVOID SCRATCHES! In order to avoid scratching this furnuture should be assembled on a soft layer-could be a rug. IMPROVE EFFICIENCY ! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time. ANTI-TOPPLE WARNING ! Overturned furniture can cause serious or fatal crush injuries.
Please prepare the following tools When installing, please carefully confirm whether each screw corresponds to the manual, accessories with similar shapes can be distinguished by size A x 36 B x 36 Cx8 Fx8 Gx5 G2 G1 6 x 28 mm H x 50 15 x 9.5 mm I x 16 8 x 40 mm Jx2 3.5 x 30 mm Kx6 Lx3 Qx4 J1 J2 200 mm 3.5 x 14 mm Mx3 Nx6 Ox6 Px6 Rx2 Sx2 Tx2 U x 18 3.5 x 20 mm 3/21 3.
3 5 6 4 7 1 8 7 8 16 x2 14 2 7 19 x2 18 x2 10 17 x2 15 11 x3 12 x6 13 x3 4/21 9
STEP1: Extend Slide Extender la diapositiva Extendre la diapositive STEP2: Push lever UP Empujar hacia arriba Lever le levier STEP3: Remove Runner Quitar el corredor Enlever le coureur 5/21
A x 20 1 Ox6 J1 x 1 Px6 Hx4 6 x 28 mm 3 x 14 mm Knock part(P) and (O) into corresponding holes in plate 1 and 2 as shown. Screw quickfit screw(A) into corresponding holes in plate 1 and 2 with a screwdriver as shown. Fix slide rail(J1) to plate 1 and 2 respectively using screw(H) as shown.
Ax2 2 Bx2 Hx4 J1 x 1 6 x 28 mm 3 x 14 mm Screw quickfit screw(A) into plate 4 as shown. Attach plate 5 to plate 4, put cam lock(B) into holes in plate 5 and turn clockwise to tighten at first. FIx slide rail(J1) to two sides of plate 5 using screw(H) as shown.
B x 20 3 Cx4 15 x 9.5 mm 8 x 40 mm Slide plate 8 along grooves in plate 4,8 and 9 at first. Insert wooden dowel(C) into plate 4 as shown. Connect plate 1 and 2 with plate 4,8,9 and 10, put cam lock(B) into holes in plate 4,8,9,10 and turn clockwise to tighten at first.
Ax6 4 Bx6 6 x 28 mm Cx4 15 x 9.5 mm 8 x 40 mm Screw quickfit screw(A) into corresponding holes in plate 3 as shown. Cover plate 3 to the top with wooden dowel(C), put cam lock(B) into holes in plate 1,4,2 and turn clockwise to tighten as shown.
I x 16 5 H x 16 Tx2 Rx2 3.5 x 14 mm 3.5 x 20 mm Reinforce back plate using part(I) and screw(H) as shown. Fix part(R) to plate 1 and 2 respectively using screw(T) as shown.
6 Fx8 3.5 x 30 mm Fix plate 16 and 17 to plate 19 using screw(F) as show. Slide plate 18 along grooves as shown.
Ax8 7 6 x 28 mm Screw quickfit screw(A) into plate 14 and 15 as shown.
Bx8 8 Gx2 G2 G1 15 x 9.5 mm Attach plate 14 and 15 respectively to the component, put cam lock(B) into holes in plate 16,17 and turn clockwise to tighten as shown. Fix handle(G1) to plate 14 and 15 using screw(G2) as shown.
J2 x 2 9 200 mm Hx8 3.5 x 14 mm Fix runner(J2) to drawer side using screw(H) as shown.
10 Gx3 U x 18 Mx3 Lx3 G2 G1 3.5 x 12 mm Fix plastic hinge(L) and (M) to plate 13 using screw(U) as shown. Fix handle(G1) to plate 13 using screw(G2) as shown.
11 Hx6 3.5 x 14 mm Fix plate 11 to plastic hinge(L) and (M) using screw(H) as shown.
Hx6 12 3.5 x 14 mm Fix plate 12 to plastic hinge(L) and (M) using screw(H) as shown.
Nx6 13 Kx6 Assemble the drawers to plate 1 and 2, knock part(N) into the holes in plastic hinges, and fix using screw(K) as shown.
14 Place plate 12 in.
15 Hx6 3.5 x 14 mm Fix plate 12 to plastic hinge(L) and (M) using screw(H) as shown.
16 Qx2 Sx2 Install anti-tipping device as shown.
