THIS INSTRUCTION BOOKLET CONTAINS ‐ ‐ ‐ ‐ IMPORTANT Unit can tip over causing severe injury or death. Anchor unit to stud in wall (if instructed to). Do Not allow children to climb on unit. Put heavy items on lower shelves or drawers. SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Helpful Hints PEOPLE NEEDED FOR ASSEMBLY: 1 - 2 ESTIMATED ASSEMBLY TIME: 1 HOUR ‐ Open your item in the area you plan to keep it to avoid excessive heavy lifting. ‐ Identify, sort and count the parts before attempting assembly. ‐ Compression dowels are lightly tapped in with a hammer. ‐ Slides are labeled with a R (right) and L (left) for proper placement. ‐ Make sure to always face the point on the top of the Cam Lock towards the outer edge.
Before You Start ‐Read through each step carefully and follow the proper order ‐Separate and count all your parts and hardware ‐Give yourself enough room for the assembly process ‐Have the following tools: Hammer ‐Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.
A B Quickfit Screw C Camlock 77 F Handl e scr ew H Smal l scr ew 5 1 2 Long screw 77 G 3 Parts assembly diagram 8 D E Long scr ew nut 24 I Dr awer l i mi t scr ew 24 10 J Dr awer handl e Scr ew of t he mi r r or 3
installation drawing 1 First install the drawer .
installation drawing 2 A B I F The installation steps of other drawers are the same 40 B 40 A 3 1 5 1.Screw A into the corresponding hole of No. 4 plate, then insert No. 1 plate into A, and finally lock A with B 5 3 2.Screw A into the corresponding hole of No. 2 plate, then insert No. 1 plate into A, and finally lock A with B A 1 1 3.Align the sheet with the slot of plate 1 and push it forward 1 2 2 4.Screw A into the corresponding hole of No. 2 plate, then connect No.
installation drawing 3 Screw in the eccentric screw on the 4 and 6 plates first First install the drawer .
installation drawing 4 C D 13 4 4 14 10 When placing D, it should be noted that the round hole should be aligned with the direction of screw in C 13 11 15 12 16 Second install the cabinet. 1.Place D in the corresponding position of plate 13 and plate 14 When placing D, it should be noted that the round hole should be aligned with the direction of screw in C 10 2.
installation drawing 5 B A 4 4 D C 8 8 1.Place D into the corresponding hole of No. 13 plate When placing D, it should be noted that the round hole should be aligned with the direction of screw in C D D 13 A 14 D 11 A D 13 12 2.
installation drawing 6 Align the sheet with the slot of plate 10, 11 and 15 and push forward
installation drawing 7 B A 6 6 E A 10 A A A A A Screw A into the corresponding hole of 14 plate Align the slide rail of the drawer with the slide rail of the cabinet and push it forward Align the panel with the previously installed part and connect it.
installation drawing 8 A 26 10 18 18 17 18 20 19 22 21 23 Connect plate 19.20.21.22.
installation drawing 9 B A 18 6 16 C D 18 17 4 19 18 4 B Connect plates 17, 18 and 19 with A B C B 26 C D B B C D B B D B Lock A with B and fix it; Put D into the corresponding hole of plate 21, and then screw in with C C D Lock A with B, place D in plate 18, and screw C in
installation drawing 10 A 7 B 7 Screw in A on the panel Align the upper part with A and connect it with the lower part, then lock and fix it with B
installation drawing 11 J 3 Screw F into the hole of plate 20 to fix the mirror Align the mirror with the hole of plate 20
installation drawing 12 C 24 8 25 D 24 25 8 G 24 8 24 25 25 Put D into the corresponding hole of plate 24, and then screw C into plate 25 h h Fix H on the inside of two 25 plates with G Fix H under the soft bag with G
