THIS INSTRUCTION BOOKLET CONTAINS ‐ ‐ ‐ ‐ IMPORTANT Unit can tip over causing severe injury or death. Anchor unit to stud in wall (if instructed to). Do Not allow children to climb on unit. Put heavy items on lower shelves or drawers. SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Helpful Hints PEOPLE NEEDED FOR ASSEMBLY: 1 - 2 ESTIMATED ASSEMBLY TIME: 1 HOUR ‐ Open your item in the area you plan to keep it to avoid excessive heavy lifting. ‐ Identify, sort and count the parts before attempting assembly. ‐ Compression dowels are lightly tapped in with a hammer. ‐ Slides are labeled with a R (right) and L (left) for proper placement. ‐ Make sure to always face the point on the top of the Cam Lock towards the outer edge.
Before You Start ‐Read through each step carefully and follow the proper order ‐Separate and count all your parts and hardware ‐Give yourself enough room for the assembly process ‐Have the following tools: Hammer ‐Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.
A Cam bolt 35×6 B Cam lock 83 F Screw 20×8 83 G Short screws 10×7 6 K Cabinet shoe C Handle I Long screws 14×3.5 16 H 28 L 10 D E Plastic plug 16 I 2 Positioning pin Φ12×8 8 J 2 Drawer rails Hinge 2 N 4 Handle II 1 Please align the triangle arrow with the screw.
installation drawing 1 A L F B N First install the drawer . Cam bolt Cam lock 32 Handle I Screw 20mm×8mm 32 1.Use A to connect No.2 board and No.3 board respectively, and then use B to lock and fix A Handle II 5 1 3 2.Align the No. 4 board with the slot of the two No. 2 boards and push it in A 3 2 A A F 4.Fix L in front of plate 1 with F 3.Use A to connect the No.
installation drawing 2 C A Second install the cabinet. D Long screws 14mm×3.5m Cam bolt 8 K Plastic plug 4 Cabinet shoe 4 4 Attention: 6 When placing D, make sure that the round hole is aligned with the direction of C 7 9 C 8 C K 9 8 1.Punch K into the bottom hole of plate 6 and 7 12 11 A K 11 7 A K K 6 C 7 10 2.Place D into the corresponding holes of No. 8 and No. 9 boards. When placing, pay attention to the round hole of D aligned with the socket of C A 11 3.
installation drawing 3 A B K Second install the cabinet. Cam lock Cam bolt Cabinet shoe 8 16 2 11 12 7 10 11 11 B K B K 11 1.Use A to connect the part installed in the previous step with plates 10, 11 and 12 12 6 7 11 9 8 11 10 During installation, it is necessary to pay attention to the direction of holes in two No. 11 boards facing backward, and the direction of holes in one No. 11 board and No. 12 board facing downward B B B 2.
installation drawing 4 A B Cam bolt C Cam lock ６ Long screws 14mm×3.5m ６ E D Positioning pin Plastic plug 2 2 8 A 2 A A A D 14 D 13 E A E A B E E E E E B C C E 14 13 1.Insert the sheet of corresponding size into the slot of No. 6, 7 and 9 plate 2.Place E in the corresponding holes of plate 6, 7 and 10 3.Use A to connect plate 13 and 14 with the part installed in the previous step, and then use B to lock A and fix it 4.
installation drawing 5 Push the drawer into the cupboard 9
installation drawing 6 A B Cam bolt C Cam lock 22 22 A D Long screws 14mm×3.5mm C B D B 18 A C 16 B D 2 1.Place D into the corresponding hole of plate 16，17 When placing, note that the round hole of D needs to be aligned with the jack direction of C 17 15 Plastic plug 2 Use A to connect plate 19, 20 with plate 21, 22, 23 and 24, and then use B to lock and fix plate A 2.Fix plate 16,17 in front of plate 18 with C 3.
installation drawing 7 21 19 Insert the corresponding size sheet into the slot of plate 19, 20 and 21 20 21 22 21 19 19 15 20 20 22 17 24 15 17 18 24 18 16 16 23 23 22 22 11
installation drawing 8 A B G Cam lock Cam bolt 7 7 Short screws 10mm×7mm I Drawer rails 4 I1 2 I2 I2 I1 Drawer rails Press the arrow to toggle the buckle, and then pull out the track. G B B B A G I1 Connect the upper and lower parts with A, and then A lock A with B A G It is recommended to turn it over and install it flat on the ground G Fix I in front of No.
installation drawing 9 G Short screws 10mm×7mm 4 Align the slide rail of plate 26 with the slide way and push it forward G I2 G I2 G G Attention： The slide rail should be inserted in line with the slide way 14
installation drawing 10 F J G Screw 20mm×8mm Short screws 10mm×7mm 1 L Handle I Hinge 12 2 1 Leave a little space between the cabinet door and the desktop G 25 F 25 G The hinge can be loosened with a screwdriver to control the gap of the door. 1.Fix L in front of plate 25 with F 2.Fix J on the inner side of No. 25 plate with G The hinge can be loosened with a screwdriver to control the distance between the door and the side plank.
installation drawing 11 C G D Long screws 14mm×3.5mm Plastic plug 8 H Short screws 10mm×7mm 8 Comer connection 4 2 C C D C C 27 27 D C C D C C 1.Place D in the hole corresponding to plate 27 26 26 When placing, pay attention to align the round hole of D with the socket of C 27 26 27 26 2.Use A to punch into the corresponding holes of the two No. 26 plates to connect them with the two No. 27 plates 3.
installation drawing 12 G K Short screws 10mm×7mm 4 Cabinet shoe 4 27 26 27 26 H K K K K Punch K into the corresponding hole at the bottom of two 26 plates G G Use G to punch into the hole corresponding to H to fix it with soft roll 17
