Fujian Newland A Auto-ID T Tech Co., Ltd.
Disclaimer © 2015 Fujian Newland Auto-ID Tech. Co., Ltd. All rights reserved. Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you should keep this manual for future reference. Do not disassemble the device or remove the seal label from the device. Otherwise, Fujian Newland Auto-ID Tech. Co., Ltd. does not assume responsibility for the warranty or replacement.
NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Revision History ................................................................................................................... 。 Preface ............................................................................................................................................................... 1 Introduction................................................................................................................................................... 1 Chapter Descriptions.......
Parameters of USB HID-KBW ................................................................................................................... 22 USB Country Keyboard Types ............................................................................................................. 22 Convert Case ....................................................................................................................................... 23 Inter-Keystroke Delay for KBW .............................................
Preface Introduction This manual provides detailed instructions for setting up and using the NLS-BS80 barcode scanner (hereinafter referred to as “the BS80” or “the scanner”). Chapter Descriptions Chapter 1, Getting Started : This chapter provides information on getting the scanner up and running for the first time. Chapter 2, System Settings : This chapter describes the barcode programming procedure and shows you how to configure system parameters.
Chapter 1 Getting Started Introduction The BS80 is a wireless pocket barcode scanner equipped with 1D or 2D scan engine to meet different needs. It is a great space-saver for busy or limited workspaces. It also supports iOS, Android, and Windows devices through Bluetooth HID or SPP communication. An illustrated introduction to the BS80 is included in this chapter. If you have the scanner at hand, make good use of it to develop a better understanding of this manual.
BS80 Scanner 3 1 Charging/Battery LED 2 Good Read LED 3 Data LED 4 Scan/Power Button 5 Delete/Reset Button 6 Function Button/Function LED 7 Micro USB Port 8 Product Label 9 Scan Window: Please remove the protective sticker from the window before use.
Functions of the Buttons Scan/Power Button *Press the button to scan barcode when the scanner is on. *Hold down the button for 3 seconds to power it on when the scanner is off. Delete/Reset Button *Press the button to remove the corresponding data from the FLASH memory in the USB mode before scanning the barcode to be deleted. *Hold down the button for 7 seconds to reset it when the scanner is on. Function Button *Press the button to turn on the HID keyboard of the connected iOS device in the Wireless mode.
Charging the Battery Charge the scanner by connecting it to a host device with USB cable, as shown below. Note: Low battery may result in failure or misoperation of the scanner. Before your first use, charge the battery for 3-4 hours.
Connecting the BS80 to Smartphone/Tablet 1. Make sure your device has HID or SPP profile. 2. Turn off the Power-Saving mode of your smartphone/tablet first. If the red Function LED on the scanner illuminates, hold down the Scan/Power button and Function button at the same time for 3 seconds or scan the barcode below to switch to the Wireless mode. Wireless Mode (Default) 3. Scan the appropriate barcode below to choose HID or SPP profile before connecting to smartphone/tablet.
(1) Click “Settings”. (2) Clickk “General”. (3) Clicck “Bluetootth”. (4) Turn itt on and search the devices. (5) Select “BS80XXX XX” to connect. (6) The e “Connecte ed” message e meanss the connecction is OK. BS80X XXXX BS80 0XXXX Co onnected t connectiion is comple eted, the blu ue Function LED on the scanner willl illuminate. 5. After the 6. Beforre using Wo ordPad file or relative APP, please e set keybo oard language of the d device to US SA langu uage.
LED Notifications Charging/Battery LED Red LED on Charging in progress. Green LED on Fully charged. Red and green LEDs flash alternately Battery not found. Red LED flashes Low battery alert. If the scanner is on and it is not connected to PC via USB cable, pressing the Scan/Power button and Delete/Reset button at the same time can display the battery level with the Charging/Battery LED. Green LED on Battery level is high. Red and green LEDs on Battery level is medium.
Turning the BS80 On/Off Turn the scanner on: Press the Scan/Power button. Turn the scanner off: By default, the scanner automatically powers off if no operation is performed on the scanner for 30 minutes. You can adjust the auto power-off time. You can also turn off the scanner by scanning the Power Off barcode. For more information, see Automatic/Manual Power-Off section in Chapter 2.
Scanning Instructions Scanning 1D Barcode Adjust the scan angle (Do not read barcode at vertical degree) or the distance between barcode and the scanner to ensure that the length of the scan line is roughly 8mm greater than that of the barcode, as shown below.
Chapter 2 System Settings Introduction This chapter describes how to configure the basic system parameters on the scanner. Restore Factory Defaults Restore Factory Defaults Operating Modes The scanner provides two operating modes: Wireless mode (Bluetooth mode) and USB mode. 1. Wireless mode Wireless Mode (default) When the scanner is in the Wireless mode, scanning the following barcodes can switch between Bluetooth HID and SPP profiles.
There are two data transmission modes: Synchronous mode and Asynchronous mode. (1) Synchronous mode: When you scan barcodes, the data will be sent to smartphone/tablet directly. If you are out of Bluetooth service range, scanned data will be lost. (2) Asynchronous mode: When you are out of Bluetooth service range, scanned data will be saved in the FLASH memory. Once you are back to service range, the data will be sent to smartphone/tablet automatically.
Query Scanner Information Query the Firmware & Hardware Versions of Scanner Query the Firmware Version of Scan Engine Query the Manufacture Date of Scanner Query the Serial Number of Scanner Query/Delete the Data in FLASH The FLASH memory is divided into a USB storage area (used to save the data acquired in the USB mode) and a Bluetooth storage area (used to save the data acquired in Bluetooth asynchronous mode). You should note that removing data from the USB storage area may take a longer time.
Sound Notifications Turn sound notifications on or off by scanning the appropriate barcode below. After this feature is enabled, the scanner beeps when one of the following events occurs: 1. The scanner is turned on. 2. The scanner resets. 3. A barcode is decoded (including good read for removing barcode data from the FLASH memory). 4. The scanner switched to the Wireless mode or USB mode. 5. Transmitting data via Bluetooth failed. 6. iOS soft keyboard is turned on or off. 7.
Vibration Notifications Turn vibration notifications on or off by scanning the appropriate barcode below. After this feature is enabled, the scanner vibrates when one of the following events occurs: 1. A barcode is decoded (including good read for removing barcode data from the FLASH memory). 2. The scanner switched to the Wireless mode or USB mode. 3. iOS soft keyboard is turned on or off. 4. Paired Bluetooth device is unpaired from the scanner. 5. Data transmission via USB starts. 6.
Terminating Character Suffix Append CRLF as Terminating Character Suffix (default) Disable Terminating Character Suffix 16
Inter-Character Delay for Bluetooth HID Select an appropriate inter-character delay to avoid data loss during transmission. This parameter is only valid in the Bluetooth HID mode.
Automatic/Manual Power-Off By default, the scanner automatically powers off if no operation is performed on the scanner for 30 minutes. This feature can help to extend battery life.
You can power off your scanner manually by scanning the barcode below. Power Off Note: After the Power Off barcode is scanned, the scanner emits a long beep and then turns off.
Time Stamp You can decide whether to send date and time or not by enabling or disabling time stamp.
Set Date & Time Step 1: Double click on BS80Setting.exe to BS80 Date&Time Setting Tool. Then check the “Auto-sync dateand time with the host” item on it. Step 2: After the time in the box is in sync with the system clock, click the “Generate Barcode” button. Step 3: Scan the barcode generated to set the date and time on the scanner. Note: You need to run this tool on the Windows XP or WIN7 operating system.
Parameters of USB HID-KBW USB Country Keyboard Types US English (default) Japan Denmark Finland France Turkey_F Italy Spain Norway Turkey_Q U.K.
Convert Case No Case Conversion (default) Convert All to Lower Case Convert All to Upper Case Invert Upper and Lower Case Characters Inter-Keystroke Delay for KBW To set the inter-keystroke delay, scan the following barcode and a digit barcode (0~F). Note: 0~F corresponds to 3ms (default), 8ms, 13ms, 18ms, 23ms, 28ms, 33ms, 38ms, 43ms, 48ms, 53ms, 58ms, 63ms, 68ms, 73ms and 78ms respectively.
Upgrade the Firmware Step 1: Install the driver: Run the CDC - Virtual COM Driver v1.1.0 program and then follow the on-screen instructions to complete the installation processs. (Skip this step if it is already installed on your PC.) Make sure that the driver is properly installed. You cannot upgrade the firmware without it. Step 2: Run the BS80Update program. Then click “Start”. Step 3: Turn on the scanner and connect it to your PC with the USB cable.
Step 4: Hold down the Function button and the Delete/Reset button on the scanner at the same time for 7 seconds to upgrade the firmware. The red and blue Function LEDs flash alternately during the updating process. Step 5: Wait for the “Firmware upgraded!” window to pop up and click “OK” to exit the program. Note: If this utility does not operate normally, check to see if the FirmwarePath in the UpdataTool.ini file is correct (its value should be identical with the name of the .bin file).
26
Chapter 3 Symbologies Introduction Every symbology (barcode type) has its own unique attributes. This chapter provides programming barcodes for configuring the scanner so that it can identify various barcode symbologies. It is recommended to disable those that are rarely used to increase the efficiency of the scanner.
Code 128 Enable (default) Disable UCC/EAN-128 Enable (default) Disable Enable (default) Disable Enable (default) Disable EAN-8 EAN-13 28
ISSN Enable (default) Disable Enable (default) Disable Enable (default) Disable Enable (default) Disable ISBN UPC-E UPC-A 29
Interleaved 2 of 5 Enable (default) Disable Enable (default) Disable Enable (default) Disable Enable (default) Disable Matrix 25 Industrial 25 Codabar 30
Code 93 Enable (default) Disable GS1 Databar (RSS) Enable (default) Disable Enable (default) Disable Enable (default) Disable Code 11 Plessey 31
MSI-Plessey Enable (default) Disable 32
Appendix Factory Defaults Table Parameter Factory Default Remark System Settings Operating Mode Wireless mode (Bluetooth mode) Bluetooth Profile HID USB Interface Type USB HID-KBW Data Transmission Mode for Bluetooth Asynchronous mode Sound Notifications Enabled Vibration Notifications Disabled Append CRLF as Terminating Terminating Character Suffix Character Suffix Inter-Character Delay for Bluetooth HID 15ms Auto Power-Off Timer 30 minutes Time Stamp Enabled Date Format Format 3:
Parameter Factory Default Remark Symbologies Code 39 Code 39 Enabled Transmit Start/Stop Character Enabled Code 39 Full ASCII Enabled Code 128 Code 128 Enabled UCC/EAN-128 UCC/EAN-128 Enabled EAN-8 EAN-8 Enabled EAN-13 EAN-13 Enabled ISSN ISSN Enabled ISBN ISBN Enabled UPC-E UPC-E Enabled UPC-A UPC-A Enabled Interleaved 2 of 5 Interleaved 2 of 5 Enabled Matrix 25 Matrix 25 Enabled Industrial 25 Industrial 25 Enabled Codabar Codabar Enabled 34
Code 93 Code 93 Enabled GS1 Databar (RSS) GS1 Databar (RSS) Enabled Code 11 Code 11 Enabled Plessey Plessey Enabled MSI-Plessey MSI-Plessey 35 Enabled
NLS-BS80 Specifications Performance Light Source 620 nm visible red LED 1D: Code 128, EAN-13, EAN-8, Code 39, UPC-A, UPC-E, Codabar, ISSN, Symbologies Interleaved 2 of 5, ISBN, Code 93, UCC/EAN-128, GS1 Databar, etc.
Digit Barcodes 0~9 37 0 1 2 3
4 5 6 7 8 9 38
A~F 39 A B C D E F
Headquarterss Fujian Newland Auto-ID Tecch Co., Ltd. Address：New wland Science e & Technologyy Park No.1 Ru ujiang West Rd., Ma awei district, Fuzhou, Fujian, China ZIP CODE：350015 TEL：+86 - （0）591-83979222 FAX：+86 - （0）591-839 979208 E-mail：markketing@nlscan n.com WEB：www.n nlscan.com Newland Euro ope BV Rolweg 25， 4104 AV Cule emborg， The e Netherlands TEL： +31 （0） 345 87 00 33 FAX： +31 （0） 345 87 00 39 Email：saless@newland-id..com WEB：www.n newland-id.com Tech Supportt： tech-suppo ort@newland--id.
