NLS-HR20-BT Barcode Scanner User Guide
Disclaimer © 2018 Fujian Newland Auto-ID Tech Co., Ltd. All rights reserved. Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you should keep this manual for future reference. Do not disassemble the device or remove the seal label from the device, doing so will void the product warranty provided by Fujian Newland Auto-ID Tech Co., Ltd. Allpicturesinthismanualareforreferenceonlyandactualproductmaydiffer.
Warrning Sta atementt FCC Regullations: This device co omplies with part p 15 of the FCC F Rules. O Operation is su ubject to the fo ollowing two co onditions: (1) This T device may m not cause harrmful interference, and (2) th his device must accept any interference received, r inclu uding interfere ence that may cause undesired ope eration. Changes or modifications m n expressly approved not a by th he party respo onsible for com mpliance could d void the use er‘s authority to o operate the eq quipment.
Table of Contents Preface ..................................................................................................................................................................................................... 1 Introduction ................................................................................................................................................................................. 1 Chapter Description ........................................................................
Reread Timeout ........................................................................................................................................................................ 23 Image Decoding Timeout .......................................................................................................................................................... 24 Scanning Preference ............................................................................................................................
Convert Case ..................................................................................................................................................................... 54 Emulate Numeric Keypad .................................................................................................................................................. 55 Fast Mode ...................................................................................................................................................
Code 128 .................................................................................................................................................................................. 79 Restore Factory Defaults ................................................................................................................................................... 79 Enable/Disable Code 128 .........................................................................................................................
2-Digit Add-On Code.......................................................................................................................................................... 99 5-Digit Add-On Code........................................................................................................................................................ 100 Add-On Code Required ..........................................................................................................................................
Codabar .................................................................................................................................................................................. 123 Restore Factory Defaults ................................................................................................................................................. 123 Enable/Disable Codabar ...........................................................................................................................
ISSN........................................................................................................................................................................................ 143 Restore Factory Defaults ................................................................................................................................................. 143 Enable/Disable ISSN ............................................................................................................................
PDF417 ECI Output ......................................................................................................................................................... 164 Micro PDF417 ......................................................................................................................................................................... 165 Restore Factory Defaults ............................................................................................................................
Chapter 7 Data Formatter ................................................................................................................................................................... 185 Introduction ............................................................................................................................................................................. 185 Add a Data Format ..............................................................................................................
Terminating Character Suffix .................................................................................................................................................. 224 Enable/Disable Terminating CharacterSuffix ................................................................................................................... 224 Set Terminating Character Suffix .....................................................................................................................................
Preface Introduction This manual provides detailed instructions for setting up and using the NLS-HR20-BTwireless barcode scanner (hereinafter referred to as “the HR20-BT” or “the scanner”). Chapter Description Chapter 1AboutNLS-HR20-BT : Gives a general description of HR20-BTscanner. Chapter2EasySet : Introduces a useful tool you can use to set up HR20 canner and develop newapplications.
Explanation of Icons This icon indicates something relevant to this manual. This icon indicates this information requires extra attention from the reader. This icon indicates handy tips that can help you use or configure the scanner with ease. This icon indicates practical examples that can help you to acquaint yourself with operations.
Chapter 1Getting Started Introduction HR20-BT scanner reads a 1D or 2D barcode by capturing its image. Adopting the advancedtechnology independently developed by Newland Auto-ID Techand2d image embedding application barcodeengine, it begins a new era of 2d image embedding application barcodeengine.
HR20-BT T Good Read LED: L Red LED flas shes slowly - L Low battery ale ert. Red LED on - Scanner is ccharging. RedLEDoffan nd greenLEDo on-Fullcharged d Blue LED flas shes slowly - P Paired but no connection es stablished. Blue LED on - Connection established. ashes once - Good read.
Ch hapter 2 Easyset ndows operatting systems.EasySet, dev veloped by Fu ujian Newland d Auto-ID Te ech Co., Ltd., is a EasySet supports Win ation tool for Newland’s N 1D/2 2D handheld barcode scanner, fixed mou unt barcode scanners and OEM O scan eng gines. configura Its main features includeingView de evice & configuration inform mation of onlin nedevice and send s serial co ommands to online o nd receive devvice response.
Chapter 3 System Setting Introduction There are three ways to configure the scanner: barcode programming, command programming and EasySet programming. Barcode Programming The scanner can be configured by scanning programming barcodes. All user programmable features/options are described along with their programming barcodes/commands in the following sections. This programming method is most straightforward. However, it requires manually scanning barcodes. As a result, errors are more likely to occur.
Enter Setup Programming Barcode/ Programming Command/Function The figure above is an example that shows you the programming barcode and command for the Enter Setup function: 1. The No Case Conversionbarcode. 2. The No Case Conversioncommand. 3. The description offeature/option. 4.
Enter Setup Use of Programming Command Besides the barcode programming method, the scanner can also be configured by serial commands (HEX) sent from the host device. All commands must be entered in uppercase letters. Use of Programming Barcodes Scanning the Enter Setup barcode can enable the scanner to enter the setup mode. Then you can scan a number of programming barcodes to configure your scanner. To exit the setup mode, scan the Exit Setup barcode or a nonprograming barcode, or reboot the scanner.
Enter Setup Illumination ** On Off Always lighting Aiming ** On Off Always lighting 9 ** Exit Setup
Enter Setup Good Read LED The green LED can be programmed to be On or Off to indicate good read.
Enter Setup Good Read LED Duration This parameter sets the amount of time that the Good Read LED to remain on following a good read. It is programmable in 1ms increments from 1ms to 2,000ms. ** Short (20ms) Medium (120ms) Long (220ms) Prolonged (320ms) Custom (1 - 2,000ms) Set the Good Read LED duration to 800ms: 11 1. Scan the Enter Setup barcode. 2. Scan the Custombarcode. 3. Scan the numeric barcodes “8”, “0” and “0” from the “Digit Barcodes” section inAppendix. 4.
Enter Setup 100ms 200ms 300ms 400ms 500ms 600ms 700ms 800ms 12 ** Exit Setup
Enter Setup 900ms 1000ms 1100ms 1200ms 1300ms 1400ms 1500ms 1600ms 13 ** Exit Setup
Enter Setup Power On Beep The scanner can be programmed to beep when it is powered on. Scan the Off barcode if you do not want a power on beep. ** On Off Good Read Beep Scanning the Off barcode can turn off the beep that indicates successful decode; scanning the Onbarcode can turn it back on.
Enter Setup Good Read Beep Duration This parameter sets the length of the beep the scanner emits on a good read. It is programmable in 1ms increments from 20ms to 300ms. Short (40ms) ** Medium (80ms) Long (120ms) Custom (20 – 300ms) Set the Good Read Beep duration to 200ms: 1. Scan the Enter Setupbarcode. 2. Scan the Custombarcode. 3. Scan the numeric barcodes “2”, “0” and “0” from the “Digit Barcodes” section inAppendix. 4. Scan the Save barcode from the “Save/Cancel Barcodes” section inAppendix. 5.
Enter Setup Good Read Beep Frequency This parameter is programmable in 1Hz increments from 20Hz to20,000Hz . Extra Low (800Hz) Low(1600Hz) ** Medium (2730Hz) High(4200Hz) Custom (20 - 20,000Hz) Set the Good Read Beep frequency to 2,000Hz: 1. Scan the Enter Setupbarcode. 2. Scan the Custombarcode. 3. Scan the numeric barcodes “2”, “0”, “0” and “0” from the “Digit Barcodes” section inAppendix. 4. Scan the Save barcode from the “Save/Cancel Barcodes” section inAppendix. 5. Scan the Exit Setupbarcode.
Enter Setup Good Read Beep Volume This parameter is programmable in 1 increments from 1 to20 ** Loud Medium Low Custom(1-20) 17 ** Exit Setup
Enter Setup Vibration Good Read Vibration On ** Off Good Read Vibration Duration This parameter is programmable in 1ms increments from 100ms to2000ms Vibration Duration 18 ** Exit Setup
Enter Setup Scan Mode Level Mode: A trigger pull activates a decode session. The decode session continues until a barcode is decoded or you release thetrigger. Trigger Mode: A trigger pull activates a decode session. The decode session continues until a barcode is decoded, eitheryou release thetrigger or decodesession timeout. Sense Mode: The scanner waits for the image stabilization timeout to expire before activating a decode session everytime it detects a change in ambient illumination.
Enter Setup ContinuousMode PulseMode BatchMode 20 ** Exit Setup
Enter Setup Decode Session Timeout This parameter sets the maximum time decode session continues during a scan attempt. It is programmable in 1ms increments from 1ms to 3,600,000ms. When it is set to 0, the timeout is infinite. The default setting is 3,000ms. Decode Session Timeout Set the decode session timeout to 1,500ms: 1. Scan the Enter Setupbarcode. 2. Scan the Decode Session Timeoutbarcode. 3. Scan the numeric barcodes “1”, “5”, “0” and “0” from the “Digit Barcodes” section inAppendix. 4.
Enter Setup Image Stabilization Timeout (Sense Mode) This parameter defines the amount of time the scanner will spend adapting to ambient environment after it decodes a barcode and “looks” for another. It is programmable in 1ms increments from 0ms to 3,000ms. The default setting is 100ms. Image Stabilization Timeout Set the image stabilization timeout to 800ms: 1. Scan the Enter Setupbarcode. 2. Scan the Image Stabilization Timeoutbarcode. 3.
Enter Setup Reread Timeout RereadTimeoutcanavoidundesiredrereadingofsamebarcodeinagivenperiodoftime.Thisfeatureisonlyapplicableto the Sense and Continuousmodes. Enable Reread Timeout: Do not allow the scanner to reread same barcode before the reread timeout expires. Disable Reread Timeout: Allow the scanner to reread same barcode. Enable Reread Timeout **Disable Reread Timeout The following parameter sets the timeout between decodes for same barcode.
Enter Setup You may wish to restarrt the reread timeout t when the scanner encounters e the e same barcod de that was decoded in the e last ssion before th he reread time eout expires. To enable this feature, sca an the Reread d Timeout Re eset On barc code. scan ses This featu ure is only effe ective when Reread R Timeo out is enabled..
Enter Setup Scanning Preference Normal Mode: Select this mode when reading barcodes on paper. Screen Mode: Select this mode when reading barcodes on the screen. BarcodePayMode:Select this mode when reading the payment barcode.
Enter Setup Surround GS1 App plication Id dentifiers ((AI’s) with h Parenthe eses WhenSurrroundGS1AII’swithParentthesesisseleccted,eachapplicationidentifie er(AI)contained dinscannedda atawillbe enclo osed in parenth heses in the outputmessage o e. ** Do Not Surround S GS S1 AI’s withPa arentheses Surround GS1 AI’s with Parentheses If Su urround GS1 AI’s A with Parrentheses is selected, s the barcode b above e is output as (01)0 00614141999996(10)10ABC CEDF123456.
Enter Setup Sensitivity Sensitivity specifies the degree of acuteness of the scanner’s response to changes in images captured. The higher the sensitivity,thelowerrequirementinimagechangetotriggerthescanner.Youcanselectanappropriatedegreeofsensitivity that fits the application environment. The feature is only applicable to the Sensemode. It is programmable from1 to 20.The default setting is Medium (5).
Enter Setup Trigger Commands When Enable Trigger Commands is selected, you can activate and deactivate the scanner in the Level mode with serial trigger commands. Sending the Start Scanning command (default: T , user-programmable) to the scanner in the Level mode activates a decode session. The decode session continues until a barcode is decoded or the decode session timeout or the scanner receives the Stop Scanning command (default: P , user- programmable).
Enter Setup Modify Stop Scanning Command The Stop Scanning Command canstimulate the trigger unreleased and consist of 1-10 characters (HEX values from 0x01 to 0xFF). In this command, the character “?” (HEX: 0x3F) cannot be the first character. The default Stop Scanning command is P .
Enter Setup Read Barc code afterr Power On O Disable: The scanner can not decod de barcodes a after power on. The illumination and aimin ng are off. You u can send Re ead Barcode Command to the scanner to o activate it. Enable: The T scanner ccan decode ba arcodes after power on.
Enter Setup Decode Area WholeAreaDecoding:Thescannerattemptstodecodebarcode(s)withinitsfieldofview,fromthecentertotheperiphery, and transmits the barcode that has been firstdecoded. Specific Area Decoding: The scanner attempts to read barcode(s) within a specified decoding area and transmits the barcode that has been first decoded. This option allows the scanner to narrow its field of view to make sure it reads only those barcodes intended by the user.
Enter Setup P Program the scanner to only o read Barc code 1 in the figure above e by setting th he decoding area t 10% top, 45% to 4 bottom, 1 15% left and 30% 3 right: 1 1. Scan the e Enter Setup p barcode. 2 2. Scan the e Top of Deco oding Areabarcode. 3 3. Scan the e numeric barccode “0” from the “Digit Barc codes” section n inAppendix. 4 4. Scan the e Save barcod de from the “Save/Cancel Ba arcodes” section inAppendix. 5 5. Scan the e Bottom of D Decoding Areabarcode. 6 6.
Enter Setup Image Flipping ** Do NotFlip Flip Horizontally FlipVertically Flip Horizontally & Vertically 33 Example of imagenotflipped Example of image flippedhorizontally Example of imageflippedvertically Example of image flipped horizontally &vertically ** Exit Setup
Enter Setup Bad Read Message Scan the appropriate barcode below to select whether or not to send a bad read message (user-programmable) when a good read does not occur before trigger release, or the decode session timeout expires, or the scanner receives the Stop Scanning command (For more information, see the “Serial Trigger Command” section in this chapter). ** Bad Read Message OFF Bad Read Message ON Set Bad Read Message Abadreadmessagecancontainupto7characters(HEXvaluesfrom0x00to0xFF).
Enter Setup Default Settings Factory Defaults Scanning the following barcode can restore the scanner to the factory defaults. You may need to reset all parameters to the factory defaults when: 1. The scanner is not properly configured so that it fails to decodebarcodes. 2. You forget previous configuration and want to avoid itsimpact. **Restore All Factory Defaults Custom Defaults Scanning the Restore All Custom Defaults barcode can reset all parameters to the custom defaults.
Enter Setup Query Product Information After scanning the barcode below, the product information (including product name, firmware version, decoder version, hardware version, product serial number, OEM serial number, manufacturing dateand data formatter version) will be sent to the host device.
Enter Setup Query Decoder Version Query Decoder Version Query Hardware Version Query Hardware Version Query Product Serial Number Query Product Serial Number 37 ** Exit Setup
Enter Setup Query OEM Serial Number Query OEM Serial Number Query Manufacturing Date Query Manufacturing Date Query Data Formatter Version Query Data Formatter Version 38 ** Exit Setup
Chapter4USBInterface Introduction There are four options for USB connection: USB HID Keyboard: The scanner’s transmission is simulated as USB keyboard input with no need for command configuration or a driver. Barcode data could be entered by the virtual keyboard directly and it is also convenient for the host device to receivedata. USB CDC: It is compliant with the standard USB CDC class specifications defined by the USB-IF and allows the host device to receive data in the way as a serial port does.
Enter Setup USB HID Keyboard When the scanner is connected to the USB port on a host device, you can enable the USB HID Keyboard feature by scanning the barcode below. Then scanner’s transmission will be simulated as USB keyboard input. The Host receives keystrokes onthe virtual keyboard. It works on a Plug and Play basis and no driver is required. ** USB HID Keyboard If the host device allows keyboard input, then no extra software is needed for HID Keyboard input.
Enter Setup USB Country Keyboard Types Keyboard layouts vary from country to country. The default setting is U.S. keyboard. ** U.S.
Enter Setup France Germany/ Australia Greece Hungary Israel (Hebrew) Italy Latin America/ South America Netherlands (Dutch) 42 ** Exit Setup
Enter Setup Norway Poland Portugal Romania Russia Slovakia Spain Sweden 43 ** Exit Setup
Enter Setup Switzerland (German) Turkey_F Turkey_Q UK Japan 44 ** Exit Setup
Enter Setup Beep on Unknown Character Due to the differences in keyboard layouts, some characters contained in barcode data may be unavailable on the selected keyboard. As a result, the scanner fails to transmit the unknown characters. Scan the appropriate barcode below to enable or disable the emission of beep when an unknown character is detected.
Entter Setup Emulate e ALT+Key ypad When Em mulate ALT+K Keypad is turn ned on, any ch haracter is sen nt via the num meric keypad and a overlook USB U country keyboard d type.This mo ode need to se et Code Page Option and U Unicode Outp put. Code Pag ge determines s the target language e. Unicode Ou utput determin nes the ASCII input to the host h device. ** Em mulate ALT+K Keypad OFF Emulate ALT+Key ypad ON ASCIII charactersbe etween 0x00~0 0x1Fwill be input in way of Function Key Mapping Set.
Enter Setup Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters,itmaybebecausethebarcodebeingscannedwascreatedusingacodepagethatisdifferentfromtheonethe host program is expecting. If this is the case, select the code page with which the barcodes were created by scanning the appropriate barcode below.
Enter Setup Code Page 1256 (Arabic) Code Page 1257 (Baltic) Code Page 1258 (Vietnamese) Code Page 936 (Simplified Chinese, GB2312,GBK） Code Page 874(Thai) 48 ** Exit Setup
Enter Setup Unicode Encoding Different host program may use different character encodings for handling incoming barcode data. For instance, Microsoft Office Word uses Unicode encoding and therefore you should turn Unicode Encoding on, whereas Microsoft Office Excel or Notepad uses Code Page encoding and therefore you should turn Unicode Encoding off. This feature is only effective when Emulate ALT+Keypad is turned on.
Enter Setup Function Key Mapping When Ctrl+ASCII Mode is selected, function characters (0x00 - 0x1F) are sent as ASCII sequences. The default setting is Off. ** Disable Ctrl+ASCII Mode Alt+Keypad Mode IfCtrl+ASCIIModeisselectedandotherparametersofUSBHIDKeyboardadoptfactorydefaults,barcode data “A(i.e. Horizontal Tab)F” (0x41/0x09/0x46) is sent asbelow: “A” - Keystroke “A”. - “Ctrl Make” + Keystroke “I” + “Ctrl Break” “F” - Keystroke “F” For some text editors, “Ctrl I” means italic convert.
Enter Setup ASCII Function Key Mapping Table 51 ASCII Function ASCII Value (HEX) Function Key Mapping Disabled Ctrl+ASCII NUL 00 Null Ctrl+@ SOH 01 Keypad Enter Ctrl+A STX 02 Caps Lock Ctrl+B ETX 03 ALT Ctrl+C EOT 04 Null Ctrl+D ENQ 05 CTRL Ctrl+E ACK 06 Null Ctrl+F BEL 07 Enter Ctrl+G BS 08 Left Arrow Ctrl+H HT 09 Horizontal Tab Ctrl+I LF 0A Down Arrow Ctrl+J VT 0B Vertical Tab Ctrl+K FF 0C Delete Ctrl+L CR 0D Enter Ctrl+M SO 0E Insert Ctrl+
Enter Setup ASCII Function Key Mapping Table (Continued) The last five characters (0x1B~0x1F) in the table above apply to US keyboard layout only. The following chart provides the equivalents of these five characters for other countries. Country Ctrl+ASCII United States Ctrl+[ Ctrl+\ Ctrl+] Ctrl+6 Ctrl+- Belgium Ctrl+[ Ctrl+< Ctrl+] Ctrl+6 Ctrl+- Scandinavia Ctrl+8 Ctrl+< Ctrl+9 Ctrl+6 Ctrl+- France Ctrl+^ Ctrl+8 Ctrl+$ Ctrl+6 Ctrl+= Germany Ctrl+Ã Ctrl++ Ctrl+6 Ctrl+- Italy
Enter Setup Inter-Keystroke Delay This parameter specifies the delay between emulated keystrokes.Scanning below barcodes to delay longer when the host device needs slower data transmission. The default setting is No Delay. ** No Delay Long Delay (40ms) Short Delay (20ms) Caps Lock The Caps Lock ON option can invert upper and lower case characters contained in barcode data. This inversion occurs regardless of the state of Caps Lock key on the host device’s keyboard.
Enter Setup Convert Case Scan the appropriate barcode below to convert all barcode data to your desired case. ** No Case Conversion Convert All to Upper Case Convert All to Lower Case When the Convert All to Lower Case feature is enabled, barcode data “AbC” is transmitted as “abc”. If Emulate ALT+Keypad ON is selected, Convert All to Lower Case and Convert All to Upper Case do not function.
Enter Setup Emulate Numeric Keypad Do Not Emulate Numeric Keypad 1: Sending a number (0-9) is emulated as keystroke(s) on main keyboard. Emulate Numeric Keypad 1: Sending a number (0-9) is emulated as keystroke(s) on numeric keypad. The state of Num Lock on the simulated numeric keypad is determined by its equivalent on the host device. If Num Lock on the host device is turned off, the output of simulated numeric keypad is function key instead of number.
Enter Setup ** Do Not Emulate Numeric Keypad 2 Emulate Numeric Keypad 2 Emulate ALT+Keypad ON prevails over Emulate NumericKeypad. Supposing the Emulate Numeric Keypad 1 and Emulate Numeric Keypad 2 features are enabled: if Num Lock on the host device is ON, “A4.5” is transmitted as“A4.5”; if Num Lock on the host device is OFF, “A4.5” is transmitted as follows: 1. “A” is sent as is because it is not included in numerickeypad; 2. “4” is sent as the function key “Cursor Move toLeft”; 3. “.” is sent; 4.
Enter Setup Character”+”,”-“,”*”,”/”Adopt Numeric Keypad ** Off On 57 ** Exit Setup
Enter Setup Fast Mode When Fast Mode On is selected, the scanner sends characters to the host faster. If the host drops characters, turn the Fast Mode off or change the polling rate to a bigger value.
Enter Setup Polling Rate This parameter specifies the polling rate for a USB keyboard. The smaller value rate is, the faster characters transmission from scanner to the host.If the host drops characters, change the polling rate to a bigger value.
Enter Setup 8ms 9ms 10ms 60 ** Exit Setup
Enter Setup USB CDC IfyourscannerisconnectedtotheUSBportonahostdevice,theUSBCDCfeatureallowsthehostdevicetoreceive data in the way as a serial port does. A driver is needed when using this feature. You may download it from our website at www.newlandaidc.com.
Enter Setup HID POS (POS HID Barcode Scanner) Introduction The HID-POS interface is recommended for new application programs. It can send up to 56 characters in a single USB report and appears more efficient than keyboard emulation. Features: 1. HID based, no custom driverrequired. 2. More efficient in communication than keyboard emulation interface.
Enter Setup Acquire Scanned Data After a barcode is decoded, the scanner sends an input report as below: Bit Byte 7 6 5 4 3 2 0 Report ID = 0x02 1 Barcode Length 2-57 Decoded Data (1-56) 58-61 Reserved 62 Newland Symbology Identifier or N/C: 0x00 63 - - - - - - 1 0 - Decoded data continued Send Command to the Scanner This output report is used to send commands to the scanner. All programming commands can be used.
Enter Setup IBM SurePOS (Tabletop) IBM SurePOS (Tabletop) IBM SurePOS (Handheld) IBM SurePOS (Handheld) VID/PID USBusesVID(VendorID)andPID(ProductID)toidentifyandlocateadevice.TheVIDisassignedbyUSBImplementers Forum.Newland’svendorIDis1EAB(Hex).ArangeofPIDsareusedforeachNewlandproductfamily.EveryPIDcontains a base number and interface type (keyboard, COM port,etc.).
Chapter5WirelessCommunication Operating Modes The scanner provides the following three operating modes. Scanning the Enter Setup Barcode to change the operating mode. The default setting is 2.4G Mode: Bluetooth HID Mode allows your scanner to communicate with a remote host using Bluetooth. You must first pair your scanner to the host before these two Bluetooth devices can communicate with each other. All features available for USB HID Keyboard are applicable to Bluetooth HID.
Enter Setup Batch Mode Batch Mode Options Off: The scanner attempts to transmit every barcode you scan. When you are out of service range, the scanned data will be lost. Automatic Batch Mode: When in service range, the scanner attempts to transmit every barcode you scan. When out of range, the scanner stores the scanned data in the flash memory. Once you are back to service range, the scanner will automatically transmit the stored data and then remove it from the flash memory after transmission is done.
Enter Setup Prevent Same Barcode Storage This feature is available only when scanning barcodes in the Automatic or Manual Batch mode. On: The scanner discards the data and generates an error beep when encountering a barcode that has existed in the flash memory. Off: The scanner stores the data when encountering a barcode that has existed in the flash memory.
Batch Mode M Trans smit Delay Sometimes when multiiple barcodes stored in the flash f memory are sent to th he host, the tra ansmission of those barcode es is or the applicattion to processs. To program m a transmit de elay between barcodes, b sca an one of the following f delayys.
Ente er Setup End of Transmissiion Messag ge for Batch h Mode You may y scan the app propriate barc code below to o select wheth her or not to send s an end of transmissio on message (user( programm mable) to notify the host when w transmis ssion of all sttored data is done. This fe eature is only y available to data transmiss sion initiated manually m unde er the Manual Batch mode.
Enter Setup Transmit Stored Data You may scan the barcode below to send the stored data in the flash memory to the host. This feature is only available to the Manual Batch mode. Transmit Stored Data Auto Clear Stored Data after Transmission You may scan the appropriate barcode below to choose whether to clear or keep the stored data in the flash memory after transmission. This feature is only available to the Manual Batch mode.
Enter Setup Clear Pairing Info on Scanner Clear Pairing Info on Scanner Tips: Clear Pairing Info on Scanneris not available in 2.
Enter Setup Auto Power-Off Timeout Auto Power-off Timeout specifies the amount of time it takes before the scanner automatically powers off from inactivity.
Enter Setup Set Scanner Name You may scan the below barcode to set the name of your scanner. The maximum length is 5 characters (HEX values from 0x20 to 0x7E). The default scanner name is “00000”. Scanner Name If setting the scanner name as “0AB00”： 1. Scan the Enter Setup barcode 2. Scan the Scanner Name barcode 3. Scan the numeric barcode “3”“0”“4”“1”“4”“2”from the “Digit Barcodes” section inAppendix 4. Scan the Save barcode from the “Save/Cancel Barcodes” section inAppendix 5.
Enter Setup Time Stamp You can select whether or not to send date & time before each scanned data by scanning the appropriate barcode below.
Set Time Stamp Format ** Format 1: (YYYY/MM/DD, HH: MM: SS) Format 2: (DD/MM/YYYY/, HH: MM: SS) (example: 2018/01/23, 10:30:20)(example: 23/01/2018, 10:30:20) Format 3: (MM/DD/YYYY,HH:MM:SS) (example: 01/23/2018, 10:30:20) 75
Enter Setup Chapter6Symbologies Introduction Everysymbology(barcodetype)hasitsownuniqueattributes.Thischapterprovidesprogrammingbarcodesforconfiguring the scanner so that it can identify various symbologies. It is recommended to disable those that are rarely used to increase the efficiency of thescanner. Global Settings Enable/Disable All Symbologies If the Disable All Symbologies feature is enabled, the scanner will not be able to read any non-programming barcodes except the programming barcodes.
Enter Setup Enable/Disable 2D Symbologies Enable 2D Symbologies Disable 2D Symbologies 77 ** Exit Setup
Enter Setup 1D Twin Code 1D twin code is two 1D barcodes of a symbology or of different symbologies paralleled vertically. Both barcodes must have similar specifications and be placed closely together. There are 3 options for reading 1D twincode: Single 1D Code Only: Read either 1Dcode. Twin 1D Code Only: Read both 1D codes. Transmission sequence: upper 1D code followed by lower 1D code. Both Single & Twin: Read both 1D codes. If successful, transmit as twin 1D code only.
Enter Setup Code 128 Restore Factory Defaults Restore the Factory Defaults of Code 128 Enable/Disable Code 128 ** Enable Code 128 Disable Code 128 If the scanner fails to identify Code 128 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Code 128 barcode.
Enter Setup Set Length Range for Code 128 The scanner can be configured to only decode Code 128 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 48) If minimum length is set to be greater than maximum length, the scanner only decodes Code 128 barcodeswitheithertheminimumormaximumlength.
Enter Setup EAN-8 Restore Factory Defaults Restore the Factory Defaults of EAN-8 Enable/Disable EAN-8 ** Enable EAN-8 Disable EAN-8 If the scanner fails to identify EAN-8 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable EAN-8 barcode. Transmit Check Character EAN-8 is 8 digits in length with the last one as its check character used to verify the integrity of the data.
Enter Setup 2-Digit Add-On Code An EAN-8 barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is an EAN-8 barcode while the part circled by red dotted line is a two-digit add-on code. ** Disable 2-Digit Add-On Code Enable 2-Digit Add-On Code Disable2-DigitAdd-OnCode:ThescannerdecodesEAN-8andignorestheadd-oncodewhenpresented with an EAN-8 plus 2-digit add-on barcode.
Enter Setup 5-Digit Add-On Code An EAN-8 barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is an EAN-8 barcode while the part circled by red dotted line is a five-digit add-on code. ** Disable 5-Digit Add-On Code Enable 5-Digit Add-On Code Disable5-DigitAdd-OnCode:ThescannerdecodesEAN-8andignorestheadd-oncodewhenpresented with an EAN-8 plus 5-digit add-on barcode.
Enter Setup Add-On Code Required When EAN-8 Add-On Code Required is selected, the scanner will only read EAN-8 barcodes that contain add-on codes. ** EAN-8 Add-On Code NotRequired EAN-8 Add-On CodeRequired Convert EAN-8 to EAN-13 ConvertEAN-8toEAN-13:ConvertEAN-8decodeddatatoEAN-13formatbeforetransmission.Afterconversion,thedata follows EAN-13 format and is affected by EAN-13 programming selections (e.g., CheckCharacter).
Enter Setup EAN-13 Restore Factory Defaults Restore the Factory Defaults of EAN-13 Enable/DisableEAN-13 ** EnableEAN-13 Disable EAN-13 If the scanner fails to identify EAN-13 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable EAN-13 barcode.
Enter Setup Transmit Check Character ** Transmit EAN-13 Check Character Do Not Transmit EAN-13 Check Character 2-Digit Add-On Code An EAN-13 barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is an EAN-13 barcode while the part circled by red dotted line is a two-digit add-on code.
Enter Setup 5-Digit Add-On Code An EAN-13 barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is an EAN-13 barcode while the part circled by red dotted line is a five-digit add-on code. ** Disable 5-Digit Add-On Code Enable 5-Digit Add-On Code Disable 5-Digit Add-On Code: The scanner decodes EAN-13 and ignores the add-on code when presented with an EAN-13 plus 5-digit add-on barcode.
Enter Setup EAN-13 Beginning with 290 Add-On Code Required This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that begin with “290”. The following settings can be programmed: RequireAdd-OnCode:AllEAN-13barcodesthatbeginwith“290”musthavea2-digitor5-digitadd-oncode.TheEAN-13 barcodewiththeadd-oncodeisthentransmitted.Iftherequiredadd-oncodeisnotfound,theEAN-13barcodeisdiscarded.
Enter Setup EAN-13 Beginning with 414/419 Add-On Code Required This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that begin with a “414” or “419”. The following settings can be programmed: Require Add-On Code: All EAN-13 barcodes that begin with a “414” or “419” must have a 2-digit or 5-digit add-on code. TheEAN-13barcodewiththeadd-oncodeisthentransmitted.Iftherequiredadd-oncodeisnotfound,theEAN-13barcode is discarded.
Enter Setup EAN-13 Beginning with 434/439 Add-On Code Required This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that begin with a “434” or “439”. The following settings can be programmed: Require Add-On Code: All EAN-13 barcodes that begin with a “434” or “439” must have a 2-digit or 5-digit add-on code. TheEAN-13barcodewiththeadd-oncodeisthentransmitted.Iftherequiredadd-oncodeisnotfound,theEAN-13barcode is discarded.
Enter Setup EAN-13 Beginning with 977 Add-On Code Required This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that begin with “977”. The following settings can be programmed: RequireAdd-OnCode:AllEAN-13barcodesthatbeginwith“977”musthavea2-digitor5-digitadd-oncode.TheEAN-13 barcodewiththeadd-oncodeisthentransmitted.Iftherequiredadd-oncodeisnotfound,theEAN-13barcodeisdiscarded.
Enter Setup EAN-13 Beginning with 979 Add-On Code Required This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that begin with “979”. The following settings can be programmed: RequireAdd-OnCode:AllEAN-13barcodesthatbeginwith“979”musthavea2-digitor5-digitadd-oncode.TheEAN-13 barcodewiththeadd-oncodeisthentransmitted.Iftherequiredadd-oncodeisnotfound,theEAN-13barcodeisdiscarded.
Enter Setup UPC-E Restore Factory Defaults Restore the Factory Defaults of UPC-E Enable/Disable UPC-E ** Enable UPC-E Disable UPC-E ** Enable UPC-E0 Disable UPC-E0 **Enable UPC-E1 Disable UPC-E1 If the scanner fails to identify UPC-E/UPC-E0/UPC-E1 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable UPC-E/UPC-E0/UPC-E1 barcode.
Enter Setup Transmit Check Character UPC-E is 8 digits in length with the last one as its check character used to verify the integrity of the data. ** Transmit UPC-E Check Character Do Not Transmit UPC-E Check Character 2-Digit Add-On Code A UPC-E barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is a UPC-E barcode while the part circled by red dotted line is a two-digit add-on code.
Enter Setup 5-Digit Add-On Code A UPC-E barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is a UPC-E barcode while the part circled by red dotted line is a five-digit add-on code. ** Disable 5-Digit Add-On Code Enable 5-Digit Add-On Code Disable 5-Digit Add-On Code: The scanner decodes UPC-E and ignores the add-on code when presented with a UPC-E plus 5-digit add-on barcode.
Enter Setup Add-On Code Required When UPC-E Add-On Code Required is selected, the scanner will only read UPC-E barcodes that contain add-on codes. ** UPC-E Add-On CodeNot Required UPC-E Add-On Code Required Transmit Preamble Character Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E barcode.
Enter Setup Convert UPC-E to UPC-A Convert UPC-E to UPC-A: Convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Character). Do Not Convert UPC-E to UPC-A: UPC-E decoded data is transmitted as UPC-E data, without conversion.
Enter Setup UPC-A Restore Factory Defaults Restore the Factory Defaults of UPC-A Enable/Disable UPC-A ** Enable UPC-A Disable UPC-A If the scanner fails to identify UPC-A barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable UPC-A barcode. Transmit Check Character UPC-A is 13 digits in length with the last one as its check character used to verify the integrity of the data.
Enter Setup 2-Digit Add-On Code A UPC-A barcode can be augmented with a two-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is a UPC-A barcode while the part circled by red dotted line is a two-digit add-on code. ** Disable 2-Digit Add-On Code Enable 2-Digit Add-On Code Disable 2-Digit Add-On Code: The scanner decodes UPC-A and ignores the add-on code when presented with a UPC-A plus 2-digit add-on barcode.
Enter Setup 5-Digit Add-On Code A UPC-A barcode can be augmented with a five-digit add-on code to form a new one. In the example below, the part surrounded by blue dotted line is a UPC-A barcode while the part circled by red dotted line is a five-digit add-on code. ** Disable 5-Digit Add-On Code Enable 5-Digit Add-On Code Disable 5-Digit Add-On Code: The scanner decodes UPC-A and ignores the add-on code when presented with a UPC-A plus 5-digit add-on barcode.
Enter Setup Add-On CodeRequired When UPC-A Add-On Code Required is selected, the scanner will only read UPC-A barcodes that contain add-on codes. **UPC-A Add-On Code Not Required UPC-A Add-On Code Required Transmit Preamble Character Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A barcode.
Enter Setup Coupon UPC-A/EAN-13 with Extended Coupon Code The following three types of coupon code + extended coupon code are supported: 1. UPC-A (starting with “5”) +GS1-128 2. UPC-A (starting with “5”) + GS1Databar 3. EAN-13 (starting with “99”) +GS1-128 Use the appropriate barcode below to enable or disable UPC-A/EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.
Enter Setup Coupon GS1 Databar Output If you scan coupons that have both UPC and GS1 Databar codes, you may wish to scan and output only the data from the GS1 Databar code. Scan the GS1 Output On barcode below to scan and output only the GS1 Databar code data. When GS1 Output Off is selected, coupons that have both UPC and GS1 Databar codes are transmitted depending on your selection for the “UPC-A/EAN-13 with Extended Coupon Code” feature.
Enter Setup Interleaved 2 of 5 Restore Factory Defaults Restore the Factory Defaults of Interleaved 2 of 5 Enable/Disable Interleaved 2 of 5 ** Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 If the scanner fails to identify Interleaved 2 of 5 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Interleaved 2 of 5 barcode.
Enter Setup Set Length Range for Interleaved 2 of 5 The scanner can be configured to only decode Interleaved 2 of 5 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 6) Set the Maximum Length (Default: 80) If minimum length is set to be greater than maximum length, the scanner only decodes Interleaved 2 of 5 barcodeswitheithertheminimumormaximumlength.
Enter Setup Check Character Verification A check character is optional for Interleaved 2 of 5 and can be added as the last character. It is a calculated value used to verify the integrity of the data. Disable: The scanner transmits Interleaved 2 of 5 barcodes as is. DoNotTransmitCheckCharacterAfterVerification:Thescannercheckstheintegrityofall Interleaved2of5barcodes to verify that the data complies with the check character algorithm.
Enter Setup Febraban Disable/Enable Febraban **Disable Febraban Enable Febraban, Do Not Expand Enable Febraban, Expand Transmit Delay per Character Transmit Delay per Character applies to both Expanded and Unexpanded Febraban. This feature is available only when USB HID Keyboard is enabled.
Enter Setup You may select an appropriate delay value from the options below as per your actual needs.
Enter Setup 40ms 45ms 50ms 55ms 60ms 65ms ** 70ms 75ms 109 ** Exit Setup
Enter Setup Transmit Delay per 12 Characters Transmit Delay per 12 Characters applies to Expanded Febraban only. This feature is available only when USB HID Keyboard is enabled. ** Disable Transmit Delay per 12 Characters Enable Transmit Delay per 12 Characters You may select an appropriate delay value from the options below as per your actual needs.
Enter Setup ** 500ms 600ms 700ms 800ms 900ms 111 ** Exit Setup
Enter Setup ITF-14 ITF-14 is a special kind of Interleaved 2 of 5 with a length of 14 characters and the last character as the check character. ITF-14 priority principle: Forthe Interleaved 2 of 5 barcodes with a length of 14 characters and the last character as the check character, the ITF-14 configurations shall take precedence over the Interleaved 2 of 5 settings.
Enter Setup ITF-6 ITF-6 is a special kind of Interleaved 2 of 5 with a length of 6 characters and the last character as the check character. ITF-6 priority principle: For the Interleaved 2 of 5 barcodes with a length of 6 characters and the last character as the check character, the ITF-6 configurations shall take precedence over the Interleaved 2 of 5 settings.
Enter Setup Matrix 2 of 5 Restore Factory Defaults Restore the Factory Defaults of Matrix 2 of 5 Enable/Disable Matrix 2 of 5 **Enable Matrix 2 of 5 Disable Matrix 2 of 5 If the scanner fails to identify Matrix 2 of 5 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Matrix 2 of 5 barcode.
Enter Setup Set Length Range for Matrix 2 of 5 ThescannercanbeconfiguredtoonlydecodeMatrix2of5barcodeswithlengthsthatfallbetween(inclusive)theminimum and maximum lengths. To accomplish it, you need to set the minimum and maximumlengths. Set the Minimum Length (Default: 4) Set the Maximum Length (Default: 80) If minimum length is set to be greater than maximum length, the scanner only decodes Matrix 2 of 5 barcodeswitheithertheminimumormaximumlength.
Enter Setup Check Character Verification AcheckcharacterisoptionalforMatrix2 of5andcanbeaddedasthelastcharacter.Itisacalculatedvalueusedtoverify the integrity of the data. Disable: The scanner transmitsMatrix 2 of 5 barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Matrix 2 of 5 barcodes to verifythatthedatacomplieswiththecheckcharacteralgorithm.
Enter Setup Code 39 Restore Factory Defaults Restore the Factory Defaults of Code 39 Enable/Disable Code39 ** Enable Code39 Disable Code 39 If the scanner fails to identify Code 39 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Code 39 barcode.
Enter Setup Set Length Range for Code 39 The scanner can be configured to only decode Code 39 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 48) Ifminimumlengthissettobegreaterthanmaximumlength,thescanneronlydecodesCode39barcodes witheithertheminimumormaximumlength.
Enter Setup Check Character Verification Acheckcharacteris optionalforCode39andcanbeaddedasthelastcharacter.Itisacalculatedvalueusedtoverifythe integrity of thedata. Disable: The scanner transmitsCode 39 barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Code 39 barcodes to verify that the data complies with the check character algorithm.
Enter Setup Transmit Start/Stop Character Code 39 uses an asterisk (*) for both the start and the stop characters. You can choose whether or not to transmit the start/stop characters by scanning the appropriate barcode below. ** Do Not Transmit Start/Stop Character Transmit Start/Stop Character Enable/Disable Code 39 Full ASCII The scanner can be configured to identify all ASCII characters by scanning the appropriate barcode below.
Enter Setup Enable/Disable Code 32 (Italian Pharma Code) Code32isavariantofCode39usedbytheItalianpharmaceuticalindustry.Scantheappropriatebarcodebelowtoenable ordisableCode32.Code39mustbeenabledandCode39checkcharacterverificationmustbedisabledforthisparameter tofunction. ** Disable Code 32 Enable Code 32 Code 32 Prefix Scan the appropriate barcode below to enable or disable adding the prefix character “A” to all Code 32 barcodes. Code 32 must be enabled for this parameter to function.
Enter Setup Transmit Code 32 Start/Stop Character Code 32 must be enabled for this parameter to function. ** Do Not Transmit Code 32 Start/Stop Character Transmit Code 32 Start/Stop Character Transmit Code 32 Check Character Code 32 must be enabled for this parameter to function.
Enter Setup Codabar Restore Factory Defaults Restore the Factory Defaults of Codabar Enable/Disable Codabar ** Enable Codabar Disable Codabar If the scanner fails to identify Codabar barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Codabar barcode.
Enter Setup Set Length Range for Codabar The scanner can be configured to only decode Codabar barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 2) Set the Maximum Length (Default: 60) Ifminimumlengthissettobegreaterthanmaximumlength,thescanneronlydecodesCodabarbarcodes witheithertheminimumormaximumlength.
Enter Setup Check Character Verification AcheckcharacterisoptionalforCodabarandcanbeaddedasthelastcharacter.Itisacalculatedvalueusedtoverifythe integrity of thedata. Disable: The scanner transmits Codabar barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Codabar barcodes to verify that the data complies with the check character algorithm.
Enter Setup Start/Stop Character You can set the start/stop characters and choose whether or not to transmit the start/stop characters by scanning the appropriate barcode below.
Enter Setup Code 93 Restore Factory Defaults Restore the Factory Defaults of Code 93 Enable/Disable Code 93 Enable Code 93 **Disable Code 93 If the scanner fails to identify Code 93 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Code 93 barcode.
Enter Setup Set Length Range for Code 93 The scanner can be configured to only decode Code 93 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 48) Ifminimumlengthissettobegreaterthanmaximumlength,thescanneronlydecodesCode93barcodes witheithertheminimumormaximumlength.
Enter Setup Check Character Verification Check characters are optional for Code 93 and can be added as the last two characters, which are calculated values used to verify the integrity of the data. Disable: The scanner transmits Code 93 barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Code 93 barcodes to verify that the data complies with the check character algorithm.
Enter Setup China Post 25 Restore Factory Defaults Restore the Factory Defaults of China Post 25 Enable/Disable China Post 25 Enable China Post 25 ** Disable China Post 25 If the scanner fails to identify China Post 25 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable China Post 25 barcode.
Enter Setup Set Length Range for China Post 25 The scanner can be configured to only decode China Post 25 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 48) If minimum length is set to be greater than maximum length, the scanner only decodes China Post 25 barcodeswitheithertheminimumormaximumlength.
Enter Setup Check Character Verification AcheckcharacterisoptionalforChinaPost25andcanbeaddedasthelastcharacter.Itisacalculatedvalueusedtoverify the integrity of thedata. Disable: The scanner transmits China Post 25 barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all China Post 25 barcodes to verifythatthedatacomplieswiththecheckcharacteralgorithm.
Enter Setup GS1-128 (UCC/EAN-128) Restore Factory Defaults Restore the Factory Defaults of GS1-128 Enable/Disable GS1-128 ** Enable GS1-128 Disable GS1-128 If the scanner fails to identify GS1-128 barcodes, you may first try this solution by scanning the EnterSetup barcode and then Enable GS1-128 barcode.
Enter Setup Set Length Range for GS1-128 The scanner can be configured to only decode GS1-128 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 48) Ifminimumlengthissettobegreaterthanmaximumlength,thescanneronlydecodesGS1-128barcodes witheithertheminimumormaximumlength.
Enter Setup GS1 Databar (RSS) Restore Factory Defaults Restore the Factory Defaults of GS1 Databar Enable/Disable GS1 Databar ** Enable GS1 Databar Disable GS1 Databar If the scanner fails to identify GS1 Databar barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable GS1 Databar barcode.
Enter Setup GS1 Composite (EAN·UCC Composite) Restore Factory Defaults Restore the Factory Defaults of GS1 Composite Enable/Disable GS1 Composite Enable GS1 Composite ** Disable GS1 Composite If the scanner fails to identify GS1 Composite barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable GS1 Composite barcode.
Enter Setup Code 11 Restore Factory Defaults Restore the Factory Defaults of Code 11 Enable/Disable Code 11 Enable Code 11 ** Disable Code 11 If the scanner fails to identify Code 11 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Code 11 barcode.
Enter Setup Set Length Range for Code 11 The scanner can be configured to only decode Code 11 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 4) Set the Maximum Length (Default: 48) Ifminimumlengthissettobegreaterthanmaximumlength,thescanneronlydecodesCode11barcodes witheithertheminimumormaximumlength.
Enter Setup Check Character Verification Check characters are optional for Code 11 and can be added as the last one or two characters, which are calculated values used to verify the integrity of the data. If the Disable option is enabled, the scanner transmits Code 11 barcodes as is.
Enter Setup Transmit Check Character Do Not Transmit Code 11 Check Character **Transmit Code 11 Check Character If you select a check character algorithm and the Do Not Transmit Check Character option, Code 11 barcodes with a length that is less than the configured minimum length after having the check character(s) excluded will not be decoded.
Enter Setup ISBN Restore Factory Defaults Restore the Factory Defaults of ISBN Enable/Disable ISBN Enable ISBN **Disable ISBN If the scanner fails to identify ISBN barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable ISBN barcode.
Enter Setup Set ISBN Format **ISBN-10 ISBN-13 ** Exit Setup 142
Enter Setup ISSN Restore Factory Defaults Restore the Factory Defaults of ISSN Enable/Disable ISSN Enable ISSN ** Disable ISSN If the scanner fails to identify ISSN barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable ISSN barcode.
Enter Setup Industrial 25 Restore Factory Defaults Restore the Factory Defaults of Industrial 25 Enable/Disable Industrial 25 Enable Industrial 25 ** Disable Industrial 25 If the scanner fails to identify Industrial 25 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Industrial 25 barcode.
Enter Setup Set Length Range for Industrial 25 ThescannercanbeconfiguredtoonlydecodeIndustrial25barcodeswithlengthsthatfallbetween(inclusive)theminimum and maximum lengths. To accomplish it, you need to set the minimum and maximumlengths. Set the Minimum Length (Default: 6) Set the Maximum Length (Default: 48) If minimum length is set to be greater than maximum length, the scanner only decodes Industrial 25 barcodeswitheithertheminimumormaximumlength.
Enter Setup Check Character Verification AcheckcharacterisoptionalforIndustrial25andcanbeaddedasthelast character.Itisacalculatedvalueusedtoverify the integrity of the data. Disable: The scanner transmits Industrial 25 barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Industrial 25 barcodes to verifythatthedatacomplieswiththecheckcharacteralgorithm.
Enter Setup Standard 25 Restore Factory Defaults Restore the Factory Defaults of Standard 25 Enable/Disable Standard 25 Enable Standard 25 **Disable Standard 25 If the scanner fails to identify Standard 25 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Standard 25 barcode.
Enter Setup Set Length Range for Standard 25 ThescannercanbeconfiguredtoonlydecodeStandard25barcodeswithlengthsthatfallbetween(inclusive)theminimum and maximum lengths. To accomplish it, you need to set the minimum and maximumlengths. Set the Minimum Length (Default: 6) Set the Maximum Length (Default: 48) If minimum length is set to be greater than maximum length, the scanner only decodes Standard 25 barcodeswitheithertheminimumormaximumlength.
Enter Setup Check Character Verification AcheckcharacterisoptionalforStandard25andcanbeaddedasthelast character.Itisacalculatedvalueusedtoverify the integrity of the data. Disable: The scanner transmits Standard 25 barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Standard 25 barcodes to verifythatthedatacomplieswiththecheckcharacteralgorithm.
Enter Setup Plessey Restore Factory Defaults Restore the Factory Defaults of Plessey Enable/Disable Plessey Enable Plessey **Disable Plessey If the scanner fails to identify Plessey barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Plessey barcode.
Enter Setup Set Length Range for Plessey ThescannercanbeconfiguredtoonlydecodePlesseybarcodeswithlengthsthatfallbetween(inclusive)theminimumand maximum lengths. To accomplish it, you need to set the minimum and maximumlengths. Set the Minimum Length (Default: 4) Set the Maximum Length (Default: 48) If minimum length is set to be greater than maximum length, the scanner only decodes Plessey barcodes witheithertheminimumormaximumlength.
Enter Setup Check Character Verification Check characters are optional for Plessey and can be added as the last two characters, which are calculated values used to verify the integrity of the data. Disable: The scanner transmits Plessey barcodes as is. Do Not Transmit Check Character After Verification: The scanner checks the integrity of all Plessey barcodes to verify that the data complies with the check character algorithm.
Enter Setup MSI-Plessey Restore Factory Defaults Restore the Factory Defaults of MSI-Plessey Enable/Disable MSI-Plessey Enable MSI-Plessey **Disable MSI-Plessey If the scanner fails to identify MSI-Plessey barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable MSI-Plessey barcode.
Enter Setup Set Length Range for MSI-Plessey ThescannercanbeconfiguredtoonlydecodeMSI-Plesseybarcodeswithlengthsthatfallbetween(inclusive)theminimum and maximum lengths. To accomplish it, you need to set the minimum and maximumlengths. Set the Minimum Length (Default: 4) Set the Maximum Length (Default: 48) If minimum length is set to be greater than maximum length, the scanner only decodes MSI-Plessey barcodeswitheithertheminimumormaximumlength.
Enter Setup Check Character Verification Check characters are optional for MSI-Plessey and can be added as the last one or two characters, which are calculated values used to verify the integrity of the data. If the Disable option is enabled, the scanner transmits MSI-Plessey barcodes as is.
Enter Setup Transmit Check Character Transmit MSI-Plessey Check Character ** Do Not Transmit MSI-Plessey Check Character IfyouselectacheckcharacteralgorithmandtheDoNotTransmitCheckCharacteroption,MSI-Plessey barcodeswithalengththatislessthantheconfiguredminimumlengthafterhavingthecheckcharacter(s) excluded will not be decoded.
Enter Setup AIM 128 Restore Factory Defaults Restore the Factory Defaults of AIM 128 Enable/Disable AIM 128 Enable AIM 128 **Disable AIM 128 If the scanner fails to identify AIM 128 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable AIM 128 barcode.
Enter Setup Set Length Range for AIM 128 The scanner can be configured to only decode AIM 128 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 48) If minimum length is set to be greater than maximum length, the scanner only decodes AIM 128 barcodes witheithertheminimumormaximumlength.
Enter Setup ISBT 128 Restore Factory Defaults Restore the Factory Defaults of ISBT 128 Enable/Disable ISBT 128 Enable ISBT 128 ** Disable ISBT 128 If the scanner fails to identify ISBT 128 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable ISBT 128 barcode.
Enter Setup PDF417 Restore Factory Defaults Restore the Factory Defaults of PDF417 Enable/DisablePDF417 ** EnablePDF417 Disable PDF417 If the scanner fails to identify PDF417 barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable PDF417 barcode.
Enter Setup Set Length Range for PDF417 The scanner can be configured to only decode PDF417 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 2710) Minimum length is not allowed to be greater than maximum length.
Enter Setup PDF417 Twin Code PDF417 twin code is 2 PDF417 barcodes paralleled vertically or horizontally. They must both be either regular or inverse barcodes. They must have similar specifications and be placed closely together. There are 3 options for reading PDF417 twin codes: Single PDF417 Only: Read either PDF417 code. Twin PDF417 Only: Read both PDF417codes. Both Single &Twin: Read both PDF417 codes. If successful, transmit as twin PDF417 only. Otherwise, try single PDF417 only.
Enter Setup PDF417 Inverse Regular barcode: Dark bars on a bright background. Inverse barcode: Bright bars on a dark background.
Enter Setup PDF417 ECI Output Disable PDF417 ECI Output **Enable PDF417 ECI Output ** Exit Setup 164
En nter Setup Micro PDF F417 Restore e Factory D Defaults Restore the Fa actory Defaults of Micro PDF417 P Enable//Disable Micro PDF417 7 E Enable Micro PDF417 sable Micro PDF417 P ** Dis e scanner fails s to identify Miicro PDF417 b barcodes, you may first try tthis solution by y scanning the e If the Ente er Setup barco ode and then Enable Micro o PDF417 barrcode.
Entter Setup Set Len ngth Range for Micro PDF417 P The scan nner can be co onfigured to on nly decode Micro PDF417 barcodes b with lengths that fa all between (in nclusive) the minimum m and maximum m lengths. To accomplish itt, you need to set the minim mum and maxim mum lengths. Set the Minimum M Len ngth (Default:: 1) Set the Maxiimum Length h (Default: 366 6) Minim mum length is not allowed d to be greate er than maxim mum length.
Enter Setup QR Code Restore Factory Defaults Restore the Factory Defaults of QR Code Enable/Disable QR Code ** Enable QR Code Disable QR Code If the scanner fails to identify QR Code barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable QR Code barcode.
Enter Setup Set Length Range for QR Code The scanner can be configured to only decode QR Code barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 7089) Minimum length is not allowed to be greater than maximum length.
Enter Setup QR Twin Code QR twin code is 2 QR barcodes paralleled vertically or horizontally. They must both be either regular or inverse barcodes. They must have similar specifications and be placed closely together. There are 3 options for reading QR twin codes: Single QR Only: Read either QR code. Twin QR Only: Read both QR codes. Transmission sequence: left (upper) QR code followed by right (lower) QR code. Both Single & Twin: Read both QR codes. If successful, transmit as twin QR only.
Enter Setup QR Inverse Regular barcode: Dark bars on a bright background. Inverse barcode: Bright bars on a dark background.
Enter Setup QR ECI Output Disable QR ECI Output **Enable QR ECI Output 171 ** Exit Setup
Entter Setup Micro QR Code Restore e Factory D Defaults Restore the Factory Defa aults of Micro o QR Enable//Disable Micro QR ** Enable Mic cro QR D Disable Micro QR If the e scanner fails s to identify Miicro QR barco odes, you may y first try this solution by sca anning the Entter Setu up barcode an nd then Enable e Micro QR b barcode.
En nter Setup Set Len ngth Range for Micro QR Q The scan nner can be co onfigured to on nly decode Micro QR barcodes with lengtths that fall be etween (inclusive) the minim mum and maxiimum lengths.. To accomplis sh it, you need d to set the miinimum and maximum m lengtths. Set the Minimum M Len ngth (Default:: 1) Set the Max ximum Length h (Default: 35 5) Minim mum length is s not allowed tto be greater tthan maximum m length.
Enter Setup Aztec Restore Factory Defaults Restore the Factory Defaults of Aztec Code Enable/Disable Aztec Code Enable Aztec Code ** Disable Aztec Code If the scanner fails to identify Aztec Code barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Aztec Code barcode.
Enter Setup Set Length Range for Aztec Code The scanner can be configured to only decode Aztec barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 3832) Minimumlengthisnotallowedtobegreaterthanmaximumlength.IfyouonlywanttoreadAztecbarcodes with a specific length, set both minimum and maximum lengths to be that desiredlength.
Enter Setup Read Multi-barcodes on an Image There are three options: Mode 1: Read one barcode only. Mode 2: Read fixed number of barcodes only. Mode 3: Composite Reading. Read fixed number of barcodes first. If unsuccessful, read one barcode only.
Enter Setup Set the Number of Barcodes ** 1 2 3 4 5 6 7 8 177 ** Exit Setup
Enter Setup Character Encoding ** Default Character Encoding UTF-8 Aztec ECI Output Disable Aztec ECI Output ** Enable Aztec ECI Output ** Exit Setup 178
Enter Setup Data Matrix Restore Factory Defaults Restore the Factory Defaults of Data Matrix Enable/Disable Data Matrix ** Enable Data Matrix Disable Data Matrix If the scanner fails to identify Data Matrix barcodes, you may first try this solution by scanning the Enter Setup barcode and then Enable Data Matrix barcode.
Enter Setup Set Length Range for Data Matrix The scanner can be configured to only decode Data Matrix barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths. Set the Minimum Length (Default: 1) Set the Maximum Length (Default: 3116) Minimum length is not allowed to be greater than maximum length.
Enter Setup Data Matrix Twin Code Data Matrix twin code is 2 Data Matrix barcodes paralleled vertically or horizontally. They must both be either regular or inverse barcodes. They must have similar specifications and be placed closely together. There are 3 options for reading Data Matrix twin codes: Single Data Matrix Only: Read either Data Matrix code. Twin Data Matrix Only: Read both Data Matrix codes. Transmission sequence: left (upper) Data Matrix code followed by right (lower) Data Matrix code.
Enter Setup Rectangular Barcode Data Matrix has two formats: Square barcodes having the same amount of modules in length and width: 10*10, 12*12.... 144*144. Rectangular barcodes having different amounts of models in length and width: 6*16, 6*14...14*22. ** Enable Rectangular Barcode Disable Rectangular Barcode Data Matrix Inverse Regular barcode: Dark bars on a bright background. Inverse barcode: Bright bars on a dark background.
Enter Setup Character Encoding ** Default Character Encoding UTF-8 Data Matrix ECI Output Disable Data Matrix ECI Output ** Enable Data Matrix ECI Output 183 ** Exit Setup
Entter Setup Passport OCR Restore e Factory D Defaults Re estore the Fa actory Defaultts of Passporrt OCR Enable//Disable Pa assport OCR R E Enable Passp port OCR sable Passporrt OCR ** Dis If the e scanner fails s to identify Pa assport OCR b barcodes, you u may first try this t solution by scanning the e Ente er Setup barco ode and then Enable Passport OCR barrcode.
Enter Setup Chapter 7 Data Formatter Introduction You may use the Data Formatter to modify the scanner’s output. For example, you can use the Data Formatter to insert charactersatcertainpointsinbarcodedataortosuppress/replace/sendcertaincharactersinbarcodedataasitisscanned. Normally, when you scan a barcode, it gets outputted automatically; however, when you create a format, you must use a “send”command(seethe“SendCommands”sectioninthischapter)withintheformatprogrammingtooutputdata.
Enter Setup Step 2: Scan the Add Data Format barcode. Add Data Format Add Data Format Step 3: Select a label (Format_0 or Format_1 or Format_2 or Format_3). Scan a numeric barcode 0 or 1 or 2 or 3 to label this data format Format_0 or Format_1 or Format_2 or Format_3. Step 4: Select formatter command type. Specify what type of formatter commands will be used. Scan a numeric barcode “6” to select formatter command type 6.
Ente er Setup Program maFormat_0da ataformatusing gformattercom mmandtype6,C Code128contaiining10charac ctersapplicable e, send all characte ers followed by y“A”. 1. Scan the t EnterSetu upbarcode 2. Scan the t Add DataFormatbarcod de 3. Scan the0 t barcode 4. Scan the6 t barcode 5. Scan the t 9 barcode ethreetimes 02 6. Scan thebarcodes0 t 010 7. Scan thebarcodes0 t 8. Scan the t alphanumericbarcodesF F141 9.
Enter Setup Programming with Serial Commands A data format can also be created by serial commands (HEX) sent from the host device. All commands must be entered in uppercase letters. The syntax consists of the following elements: Prefix: “~0000” (HEX: 7E 01 30 30 30 30), 6 characters. Storagetype:“@”(HEX:40)or“#”(HEX:23),1character.“@”meanspermanentsettingwhichwillnotbelostbyremoving powerfromthescannerorrebootingit;“#”meanstemporarysettingwhichwillbelostbyremovingpowerfromthescanner or rebooting it.
Enter Setup Enable/Disable Data Formatter When Data Formatter is disabled, the barcode data is outputted to the host as read, including prefixes and suffixes. ** Disable Data Formatter You may wish to require the data to conform to a data format you have created.
Enter Setup Enable Data Formatter, Required, Keep Prefix/Suffix Enable Data Formatter, Required, Drop Prefix/Suffix Enable Data Formatter, Not Required, KeepPrefix/Suffix Enable Data Formatter, Not Required, Drop Prefix/Suffix Non-Match Error Beep If Non-Match Error Beep is turned ON, the scanner generates an error beep when a barcode is encountered that does not match your required data format.
Enter Setup Data Format Selection After enabling the Data Formatter, you can select a data format you want to use by scanning the appropriate barcode below. The default setting is Format_0.
Enter Setup Change Data Format for a Single Scan You can switch between data formats for a single scan. The next barcode is scanned using the data format selected here, then reverts to the format you have selected above. For example, you may have set your scanner to use the data format you saved as Format_3. You can switch to Format_1 for a single trigger pull by scanning the Single Scan – Format_1 barcode below. The next barcode that is scanned uses Format_1, then reverts back to Format_3.
Enter Setup Clear Data Format There are two methods to remove data format created from your scanner: Delete one data format: Scan the Clear One barcode, a numeric barcode (0-3) and the Save barcode. For example, to delete Format_2, you should scan the Clear One barcode, the 2 barcode and the Save barcode Delete all data formats: Scan the Clear All barcode.
Enter Setup Formatter Command Type 6 WhenworkingwiththeDataFormatter,avirtualcursorismovedalongyourinputdatastring.Thefollowingcommandsare used to both move this cursor to different positions, and to select, replace, and insert data into the final output. For the hex value of ASCII characters involved in the commands, refer to the “ASCII Table” inAppendix.
Enter Setup F3 Send all characters up to a particular character Syntax=F3ssxx (ss: The particular character’s hex value; xx: The insert character’s hex value) Includeintheoutputmessageallcharactersfromtheinputmessage,startingwiththecharacteratthecurrentcursorposition and continuing to, but not including, the particular character “ss,” followed by character “xx.” The cursor is moved forward to the “ss”character.
Enter Setup Command string: B900024142 B9 is the “Send all characters up to a particular string”command 0002 is the length of the particular string (2 characters) 41 is the hex value for a “A” (character in the string) 42 is the hex value for a “B” (character in the string) The data is output as: 1234567890 E9 Send all but the last characters Syntax=E9nn (nn: The numeric value (00-99) for the number of characters that will not be sent at the end of the message) Include in the output message all but the la
Enter Setup E9 and F4 Example: Send all but the last characters, followed by 2 tabs Send all characters except for the last 9 from the barcode above, followed by 2 tabs.
Enter Setup B3 and B4 Example: Insert the symbology name and length Send the symbology name and length before the barcode data from the barcode above. Break up these insertions with spaces. End with a carriage return.
Enter Setup F5 Example: Move the cursor forward and send the data Move the cursor forward 3 characters, then send the rest of the barcode data from the barcode above. End with a carriage return.
Enter Setup Search Commands F8 Search forward for a character Syntax＝F8xx (xx: The search character’s hex value) Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. F8 Example: Send barcode data that starts after a particular character Search for the letter “D” in barcodes and send all the data that follows, including the “D”.
Enter Setup B0 Search forward for a string Syntax=B0nnnnS (nnnn: The string length (up to 9999); S: The ASCII hex value of each character in the string) Search forward for “S” string from the current cursor position, leaving cursor pointing to “S” string. For example, B0000454657374 will search forward for the first occurrence of the 4-character string “Test.
Enter Setup E6 Search forward for a non-matchingcharacter Syntax=E6xx (xx: The search character’s hexvalue) Searchtheinputmessageforwardforthefirstnon-“xx”characterfromthecurrentcursorposition,leavingthecursorpointing to the non-“xx”character. E6 Example: Remove zeros at the beginning of barcode data Thisexampleshowsabarcodethathasbeenzerofilled.Youmaywanttoignorethezerosandsendallthedatathatfollows. E6searchesforwardforthefirstcharacterthatisnotzero,thensendsallthedataafter,followedbyacarriagereturn.
Ente er Setup Compa arison Command B2 string g is compared with B@ Syntax= B2nnnnSS1SSn (nnnn：the e length of cha aracter string，SS1- SSn：the hex value e of character string) The comparison starts s from the righ ht side of the current curso or position, an nd the cursor moves nnnn characters to o the right. If th he string within the cursor movement m ran nge is equal to o SS1SSn, the e instruction continues to ex xecute; otherw wise, it exits.
Entter Setup The data is output as 0000123abc ck if the chara acter to the riight of the cu ursor is non-n numeric ED Chec This com mmand takes no n parameters s. If the right sside of the curs sor is a number, the current command is s exited, otherw wise execution n continues.
Enter Setup the characters to be suppressed) Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. FB Example: Remove spaces and other characters in barcode data This example shows a barcode that has spaces, “_” and “*” in the data. You may want to remove the three kinds of characters before sending the data.
Enter Setup E4 Example: Replace zeros with CRs in barcode data If the barcode has characters that the host application does not want included, you can use the E4 command to replace thosecharacterswithsomethingelse.Inthisexample,youwillreplacethezerosinthebarcodeabovewithcarriagereturns.
Enter Setup BA Replace a string multiple times Syntax＝BAnnNN1SS1NN2SS2 nn: The count of replacements to be made, if nn=00 or nn>=the number of occurrences of a string to be replaced, then replace all occurrences of that string. NN1: The length of the string to be replaced, NN1>0. SS1: The ASCII hex value of each character in the string to be replaced. NN2: The length of replacement string, NN2>=0. To replace string “SS1” with NUL (i.e. deIete string “SS1”), you should set NN2 to 00 and leave out SS2.
Enter Setup 32 is the hex value for 2 (character in the string to be replaced) 33 is the hex value for 3 (character in the string to be replaced) 03 is the length of XYZ 58595A is the hex value for XYZ F1 is the “Send all characters”command 00 is the hex value for a NUL The data is output as: 1XYZ4AbcXYZR0123U EF Insert a delay Syntax＝EFnnnn (nnnn: The delay in 5ms increments, up to 9999ms) Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position.
Enter Setup B5 Insert key strokes Syntax=B5nnssxx (nn: The number of keys pressed (without key modifiers); ss: the key modifier from the table below; xx: the key number from the “Unicode Key Maps” in Appendix.) Insertakeystrokeorcombinationofkeystrokes.Keystrokesaredependentonyourkeyboard(seethe“UnicodeKeyMaps” in Appendix). This command can only be used with USB HIDKeyboard.
Enter Setup Chapter 8 Prefix & Suffix Introduction A1Dbarcodecouldcontaindigits,letters,symbols,etc.A2Dbarcodecouldcontainmoredata,suchasChinesecharacters and other multi-byte characters. However, in real applications, they do not and should not have all information we need, such as barcode type, data acquisition time and delimiter, in order to keep the barcodes short andflexible. Preffixandsuffixarehowtofulfilltheneedsmentionedabove.
Enter Setup Global Settings Enable/Disable All Prefixes/Suffixes Disable All Prefixes/Suffixes: Transmit barcode data with no prefix/suffix. EnableAllPrefixes/Suffixes:AllowtoappendCodeIDprefix,AIMIDprefix,customprefix/suffixandterminatingcharacter to the barcode data before thetransmission.
Enter Setup Custom Prefix Enable/Disable Custom Prefix If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot exceed 10 characters. For example, if the custom prefix is “AB” and the barcode data is “123”, the Host will receive “AB123”.
Enter Setup AIM ID Prefix AIM (Automatic Identification Manufacturers) ID defines symbology identifier (For the details, see the “AIM ID Table” section in Appendix). If AIM ID prefix is enabled, the scanner will add the symbology identifier before the scanned data after decoding. ** Disable AIM ID Prefix Enable AIM ID Prefix AIM ID is not user programmable.
Enter Setup Code ID Prefix CodeIDcanalsobeusedtoidentifybarcodetype.UnlikeAIMID,CodeIDisuserprogrammable.CodeIDcanonlyconsist of one or two Englishletters. ** Disable Code ID Prefix Enable Code ID Prefix Restore All Default Code IDs For the information of default Code IDs, see the “Code ID Table” section in Appendix. Restore All Default Code IDs Modify Code ID See the examples below to learn how to modify a Code ID and restore the default Code IDs of all symbologies.
Enter Setup Modify PDF417 Code ID to be “p” (HEX: 0x70): 1. Scan the Enter Setup barcode. 2. Scan the Modify PDF417 Code IDbarcode. 3. Scan the numeric barcodes “7” and “0” from the “Digit Barcodes” section inAppendix. 4. Scan the Save barcode from the “Save/Cancel Barcodes” section inAppendix. 5. Scan the Exit Setup barcode. Restore the default Code IDs of all symbologies: 215 1. Scan the Enter Setup barcode. 2. Scan the Restore All Default Code IDsbarcode. 3. Scan the Exit Setup barcode.
Enter Setup Modify 1D symbologies Modify Code 128 Code ID Modify GS1-128 Code ID Modify EAN-8 CodeID Modify EAN-13 Code ID Modify UPC-E CodeID Modify UPC-A Code ID Modify Interleaved 2 of 5 Code ID ** Exit Setup 216
Enter Setup Modify ITF-14 Code ID ModifyITF-6 Code ID ModifyMatrix 2 of 5Code ID ModifyCode 39 ModifyCodabarCode ID ModifyCode 93Code ID ModifyChina Post 25Code ID ModifyAIM 128Code ID 217 ** Exit Setup
Enter Setup ModifyISBT 128Code ID ModifyISSNCode ID ModifyISBN Code ID ModifyIndustrial 25 Code ID ModifyStandard 25 Code ID ModifyPlessey Code ID ModifyCode 11Code ID ModifyMSI PlessyCode ID ** Exit Setup 218
Enter Setup ModifyGS1 Composite Code ID ModifyGS1 Databar (RSS)Code ID 219 ** Exit Setup
Enter Setup Modify 2D symbologies: Modify Aztec Code ID Modify QR Code ID Modify PDF417 Code ID Modify Data Matrix Code ID ** Exit Setup 220
Enter Setup Custom Suffix Enable/Disable Custom Suffix If custom suffix is enabled, you are allowed to append to the data a user-defined suffix that cannot exceed 10 characters. For example, if the custom suffix is “AB” and the barcode data is “123”, the Host will receive “123AB”.
Enter Setup Data Packing Introduction Datapackingisdesignedforaspecificgroupofuserswhowanttohavethedatapackedbeforetransmission.Datapacking influences data format, so it is advised to disable this feature when it is notrequired. Data Packing Options Disable Data Packing: Transmit decoded data in raw format (unpacketed). Enable Data Packing, Format 1: Transmit decoded data with the packet format 1 defined below.
Enter Setup ** Disable Data Packing Enable Data Packing, Format 1 Enable Data Packing, Format 2 223 ** Exit Setup
Enter Setup Terminating Character Suffix Enable/Disable Terminating CharacterSuffix Aterminatingcharactersuchascarriagereturn(CR)orcarriagereturn/linefeedpair(CRLF)canonlybeusedtomarkthe end of data, which means nothing can be added afterit.
Enter Setup Set the terminating character suffix to 0x0A: 225 1. Scan the Enter Setup barcode. 2. Scan the Set Terminating Character Suffixbarcode. 3. Scan the numeric barcodes “0” and “A” from the “Digit Barcodes” section inAppendix. 4. Scan the Save barcode from the “Save/Cancel Barcodes” section inAppendix. 5. Scan the Enable Terminating Character Suffix barcode. 6. Scan the Exit Setup barcode.
Appendix Enter Setup Digit Barcodes 0~9 0 1 2 3 4 5 226
6 7 8 9 227
A~F A B C D E F 228
Save/Cancel Barcodes Afterreadingnumericbarcode(s),youneedtoscantheSavebarcodetosavethedata.Ifyouscanthewrongdigit(s),you can either scan the Cancel barcode and then start the configuration all over again, or scan the Delete the Last Digit barcode and then the correct digit, or scan the Delete All Digits barcode and then the digits youwant. For instance, after reading the Maximum Length barcode and numeric barcodes “1”, “2” and “3”, you scan: Delete the Last Digit: The last digit “3” will beremoved.
Factory Defaults Table Parameter Factory Default Remark System Settings Barcode Programming Disabled (Exit Setup) Programming Barcode Data Do not transmit Illumination On Aiming On Good Read LED On Good Read LED Duration Short (20ms) Power On Beep On Good Read Beep On Good Read Beep Duration Medium (80ms) Good Read Beep Frequency Medium (2730Hz) Good Read Beep Volume Loud Good Read Vibration Off Good Read Vibration Duration 300ms Scan Mode Level Mode Decode Session Timeout 3,
USB Interface USB Country Keyboard US keyboard USB HID Keyboard Beep on Unknown Character Off USB HID Keyboard Emulate ALT+Keypad Off USB HID Keyboard Code Page 1252 (West European Latin) USB HID Keyboard Code Page Unicode Encoding Off USB HID Keyboard Emulate Keypad with Leading Zero On USB HID Keyboard Function Key Mapping Disable USB HID Keyboard Inter-Keystroke Delay No Delay USB HID Keyboard Caps Lock Off(Non Japanese Keypad) USB HID Keyboard Convert Case No Case Conversion
Check Character Transmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code Required Not Required Convert EAN-8 to EAN-13 Disabled EAN-13 EAN-13 Enabled Check Character Transmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled EAN-13 Beginning with 290 Add-On Code Required EAN-13 Beginning with 378/379 Add-On Code Required EAN-13 Beginning with 414/419 Add-On Code Required EAN-13 Beginning with 434/439 Add-On Code Required EAN-13 Beginning with 977 Add-On Code
Check Character Transmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code Required Not Required Transmit Preamble Character System Character Coupon UPC-A/EAN-13 with Extended Coupon Off Code Coupon GS1 DataBar Output Off Interleaved 2 of 5 Interleaved 2 of 5 Enabled Maximum Length 80 Minimum Length 6 Check Character Verification Febraban Do not transmit check digit after verification Febraban Disable Transmit Delay per Character Disable Transmit Delay per 12
Code 32 Prefix Disabled Code 32 Start/Stop Character Do not transmit Code 32 Check Character Do not transmit Codabar Codabar Enabled Maximum Length 60 Minimum Length 2 Check Character Verification Disabled Start/Stop Character Do not transmit ABCD/ABCD All capital Code 93 Code 93 Disabled Maximum Length 48 Minimum Length 1 Check Character Verification Do Not Transmit Check Character After Verification China Post 25 China Post 25 Disabled Maximum Length 48 Minimum Length 1 C
Check Character Transmit ISBN ISBN Enabled Set ISBN Format ISBN-10 ISSN ISSN Disabled Industrial 25 Industrial 25 Enabled Maximum Length 48 Minimum Length 6 Check Character Verification Disabled No less than 4 Standard 25 Standard 25 Disabled Maximum Length 48 Minimum Length 6 Check Character Verification Do Not Transmit Check Character After Verification No less than 4 Plessey Plessey Disabled Maximum Length 48 Minimum Length 4 Check Character Verification Do Not Trans
Maximum Length 2710 Minimum Length 1 PDF417 Twin Code Single PDF417 Only PDF417 Inverse Decode Regular PDF417 Barcodes Only Character Encoding Default Character Encoding PDF417 ECI Output Enabled Micro PDF417 Micro PDF417 Enabled Maximum Length 366 Minimum Length 1 QR Code QR Code Enabled Maximum Length 7089 Minimum Length 1 QR Twin Code Single QR Only QR Inverse Decode Regular QR Barcodes Only Character Encoding Default Character Encoding QR ECI Output Disabled Micro QR Co
Character Encoding Default Character Encoding Data Matrix ECI Output Enabled Passport OCR Passport OCR Disable Data Formatter Data Formatter Disabled Data Format Selection Format_0 Non-Match Error Beep On Multiple Data Format Setting Disabled Prefix & Suffix All Prefixes/Suffixes Disabled Prefix Sequence Code ID+ Custom +AIM ID Custom Prefix Disabled AIM ID Prefix Disabled Code ID Prefix Disabled Custom Suffix Disabled Data Packing Disable Data Packing Terminating Character Suffi
AIM ID Table Symbology AIM ID Code128 ]C0 GS1-128 (UCC/EAN-128) ]C1 EAN-8 ]E4 EAN-8 with Addon ]E3 EAN-13 ]E0 EAN-13 with Addon ]E3 UPC-E ]E0 UPC-E with Addon ]E3 UPC-A ]E0 UPC-A with Addon ]E3 Interleaved 2 of 5, Febraban ]Im Possible AIM ID Modifiers (m) 0, 1, 3 ITF-14 ]Im 1, 3 ITF-6 ]Im 1, 3 Matrix 2 of 5 ]X0 Code 39 ]Am 0, 1, 3, 4, 5, 7 Codabar ]Fm 0, 2, 4 Code 93 ]G0 China Post 25 ]X0 AIM 128 ]C2 ISSN ]X0 ISBT 128 ]C4 ISBN ]X0 Industrial 25 ]S0 Stan
Micro PDF 417 ]L0 QR Code ]Qm Micro QR Code ]Q1 Aztec ]zm 0-9, A-C Data Matrix ]dm 0-6 Passport OCR ]o2 0-6 Note:“m”representstheAIMmodifiercharacter.RefertoISO/IEC15424:2008Informationtechnology–Automaticidentification anddatacapturetechniques –DataCarrierIdentifiers (includingSymbologyIdentifiers)forAIMmodifiercharacterdetails.
Code ID Table Symbology Code ID Code128 j GS1-128 (UCC/EAN-128) j EAN-8 d EAN-13 d UPC-E c UPC-A c Interleaved 2 of 5 e ITF-14 e ITF-6 e Matrix 2 of 5 v Code 39 b Codabar a Code 93 i China Post 25 X AIM 128 X ISBT 128 X ISSN g ISBN B Industrial 25 I Standard 25 f Plessey n Code 11 H MSI Plessey m GS1 Composite y GS1 Databar (RSS) R PDF417 r Micro PDF 417 R QR Code s Micro QR Code X Aztec z Data Matrix u MaxiCode x Passport OCR O 240
Symbology ID Number Symbology ID Number Code 128 002 GS1-128 (UCC/EAN-128) 003 EAN-8 004 EAN-13 005 UPC-E 006 UPC-A 007 Interleaved 2 of 5 008 ITF-14 009 ITF-6 010 Matrix 2 of 5 011 Code 39 013 Codabar 015 Code 93 017 AIM 128 020 China Post 25 019 ISBT 128 021 ISSN 023 ISBN 024 Industrial25 025 Standard25 026 Plessey 027 Code11 028 MSI-Plessey 029 GS1 Composite 030 GS1 Databar (RSS) 031 PDF417 032 Micro PDF 417 042 QR Code 033 Micro QR Code 043 Azt
ASCII Table Hex Dec Char 00 0 NUL (Null char.
243 Hex Dec Char 1e 30 RS (Request to Send) 1f 31 US (Unit Separator) 20 32 SP (Space) 21 33 ! (Exclamation Mark) 22 34 " (DoubleQuote) 23 35 # (Number Sign) 24 36 $ (DollarSign) 25 37 % (Percent) 26 38 & (Ampersand) 27 39 ` (Single Quote) 28 40 ( (Left/ Opening Parenthesis) 29 41 ) (Right/ Closing Parenthesis) 2a 42 * (Asterisk) 2b 43 + (Plus) 2c 44 , (Comma) 2d 45 - (Minus/Dash) 2e 46 .
Hex Dec Char 3e 62 > (GreaterThan) 3f 63 ? (QuestionMark) 40 64 @ (ATSymbol) 41 65 A 42 66 B 43 67 C 44 68 D 45 69 E 46 70 F 47 71 G 48 72 H 49 73 I 4a 74 J 4b 75 K 4c 76 L 4d 77 M 4e 78 N 4f 79 O 50 80 P 51 81 Q 52 82 R 53 83 S 54 84 T 55 85 U 56 86 V 57 87 W 58 88 X 59 89 Y 5a 90 Z 5b 91 [ (Left/ OpeningBracket) 5c 92 \ (Back Slash) 5d 93 ] (Right/ ClosingBracket) 244
245 Hex Dec Char 5e 94 ^ (Caret/Circumflex) 5f 95 _ (Underscore) 60 96 ' (GraveAccent) 61 97 a 62 98 b 63 99 c 64 100 d 65 101 e 66 102 f 67 103 g 68 104 h 69 105 i 6a 106 j 6b 107 k 6c 108 l 6d 109 m 6e 110 n 6f 111 o 70 112 p 71 113 q 72 114 r 73 115 s 74 116 t 75 117 u 76 118 v 77 119 w 78 120 x 79 121 y 7a 122 z 7b 123 { (Left/ OpeningBrace) 7c 124 | (VerticalBar) 7d 125 } (Right/ Closing Brace) 7e
Unicode Key Maps 104 Key y U.S.
Ne ewland Auto-ID A T Tech Co.., Ltd. (Headquarrter) Add: Newland Sc cience & Tech hnology Park No.1 N Rujiang W West Rd., Ma awei district Fu uzhou, Fujian China Tell: +86 (0) 591 8397 9500 Fax x: +86 (0)591 8397 9216 E-m mail: info@nls scan.com We eb:www.newlandaidc.com Ne ewland APA AC Newland Taiwan Inc. Add d: 7F-6, No. 268, Liancheng Rd., Jhonghe Dist. 235, New Taipei C City, Taiw wan Tel:: +886 2 7731 53 388 Faxx: +886 2 7731 5389 Email: info@newlan nd-id.com.tw Web: www.newland d-id.com.
