BL01619-201 DIGITAL CAMERA X-Pro1 Owner’s Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM X-Pro1 digital camera and install the supplied software. Be sure that you have read and understood its contents before using the camera. EN Before You Begin First Steps Taking Photographs More on Photography Viewing Pictures Menus Connections For information on related products, visit our website at http://www.fujifilm.com/products/digital_cameras/index.
For Your Safety IMPORTANT SAFETY INSTRUCTIONS • Read Instructions: All the safety and operating instructions should be read before the appliance is operated. • Retain Instructions: The safety and operating instructions should be retained for future reference. • Heed Warnings: All warnings on the appliance and in the operating instructions should be adhered to. • Follow Instructions: All operating and use instructions should be followed.
For Your Safety Service Be sure to read these notes before use Servicing: Do not attempt to service this video product Safety Notes yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to • Make sure that you use your camera correctly. Read these qualified service personnel. safety notes and your Owner’s Manual carefully before use.
For Your Safety WARNING Use only batteries or AC power adapters specified for use with this camera. Do not use voltages other than the power supply voltage shown. The use of other power sources can cause a fire. If the battery leaks and fluid gets in contact with your eyes, skin or clothing, flush the affected area with clean water and seek medical attention or call an emergency number right away. Do not use the charger to charge batteries other than those specified here.
For Your Safety move the batteries. Note that the camera clock will be reset. The batteries may be warm to the touch immediately after use. Turn the camera off and allow the batteries to cool before handling. Battery capacity tends to decrease at low temperatures. Keep spare batteries in a pocket or other warm place and If the camera will not be used for an extended period, reexchange as necessary.
For Your Safety Using the Camera Do not aim the camera at extremely bright light sources, such as the sun in a cloudless sky. Failure to observe this precaution could damage the camera image sensor. Take Test Shots Before taking photographs on important occasions (such as at weddings or before taking the camera on a trip), take a test shot and view the results to ensure that the camera is functioning normally.
For Your Safety Notes on the Grant: To comply with Part 15 of the FCC Rules, NOTICES this product must be used with a Fujifilm-specified ferriteTo prevent fire or shock hazard, do not expose the unit core A/V cable, USB cable, and DC supply cord. to rain or moisture. For Customers in Canada Please read the “Safety Notes” and make sure you unCAUTION: This Class B digital apparatus complies with Canaderstand them before using the camera. dian ICES-003. Perchlorate Material—special handling may apply.
About This Manual Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information on specific topics, consult the sources below. Task Index ............................................................ P ix Know what you want to do but don’t know the name for it? Find the answer in the “Task Index.” Table of Contents ................................................. P xii The “Table of Contents” gives an overview of the entire manual.
Task Index Find items by task. ■ Exchanging Lenses Attaching lenses.....................................................................11 Removing lenses....................................................................11 ■ Taking Photographs The optical viewfinder........................................................20 Power management............................................................23 The self-timer ...........................................................................
Task Index ■ Choosing a Drive Mode Burst photography................................................................34 Bracketing ..................................................................................35 Panoramas .................................................................................37 Movies ..........................................................................................39 ■ Using the Flash Flash photography ...............................................................
Product Care Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body. Any liquid on the camera should be removed immediately with a soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then gently wipe with a soft, dry cloth.
Table of Contents For Your Safety .....................................................................................ii IMPORTANT SAFETY INSTRUCTIONS.........................................ii Safety Notes .......................................................................................iii NOTICES ..............................................................................................vii About This Manual ..........................................................................
Table of Contents More on Photography Viewing Pictures F Macro Mode (Close-ups) ......................................................... 31 White Balance ................................................................................... 32 I Continuous Shooting (Burst Mode) .................................. 34 Bracketing ........................................................................................... 35 Multiple Exposures .....................................................................
Table of Contents Menus Using the Menus: Shooting Mode ........................................... 67 Shooting Menu Options.............................................................. 67 N ISO .............................................................................................. 67 O IMAGE SIZE.............................................................................. 67 T IMAGE QUALITY .................................................................... 67 U DYNAMIC RANGE.....................
Table of Contents The Setup Menu ............................................................................... 79 Using the Setup Menu ................................................................. 79 Setup Menu Options .................................................................... 80 F DATE/TIME ............................................................................... 80 N TIME DIFFERENCE ................................................................. 80 L a .............................
Table of Contents Technical Notes Appendix Optional Accessories...................................................................... 96 Accessories from FUJIFILM ......................................................... 96 Recommended Third-Party Accessories ............................... 98 Connecting the Camera to Other Devices ........................... 99 Caring for the Camera .................................................................100 Storage and Use .....................................
Before You Begin Symbols and Conventions Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may be simplified for explanatory purposes. Supplied Accessories Before You Begin The following symbols are used in this manual: Q This information should be read before use to ensure correct operation. R Additional information that may be helpful when using the camera. POther pages in this manual on which related information may be found.
Parts of the Camera For more information, refer to the page listed to the right of each item. 1 Shutter button ..................................................30 2 Exposure compensation dial .............................29 3 Shutter speed dial........................... 24, 25, 26, 27 4 Dial release .................................................25, 27 5 AF-assist illuminator .........................................72 Self-timer lamp ................................................41 6 Hot shoe ......
Parts of the Camera The Indicator Lamp The indicator lamp shows camera status as follows: Indicator lamp Glows green Blinks green Blinks green and orange Glows orange Blinks red Before You Begin 36 Q (quick menu) button .......................................5 37 MENU/OK button ...............................................4 38 Selector ..............................................................4 39 DISP (display)/BACK button ............................21 o (silent mode) button......................
Parts of the Camera The Selector Press the selector up (q), right (w), down (e), or left (r) to highlight items and press MENU/ OK (t) to select. Pressing the selector up (MACRO) during shooting displays macro options (P 31). Control Lock To avoid accidentally displaying macro options during shooting, press MENU/OK until X is displayed. The control can be unlocked by pressing MENU/OK until X is no longer displayed.
Parts of the Camera The Q (Quick Menu) Button Press Q for quick access to the following items: P 52 48 68 32 69 67 Option T IMAGE QUALITY P FILM SIMULATION r HIGHLIGHT TONE s SHADOW TONE f COLOR q SHARPNESS P 67 51 69 69 68 69 Option B SELF-TIMER F AF MODE I FLASH MODE J LCD BRIGHTNESS 1 Press Q to display the quick menu during shooting.
Parts of the Camera Camera Displays The following types of indicator may be displayed during shooting and playback. Indicators vary with camera settings. ■ Shooting: Optical Viewfinder F 100 100 0.1 0.5 1.0 P 2000 1.5 F5.6 2.0 3.0 F 1 Manual focus indicator .....................................45 2 Flash mode .......................................................54 3 Metering...........................................................49 4 White balance................................................
Parts of the Camera ■ Shooting: Electronic Viewfinder 100 1.0 2000 1.5 2.0 3.0 5.0 10 F5.6 200 1 Flash mode .......................................................54 2 Macro (close-up) mode.....................................31 3 Self-timer indicator ..........................................41 4 Continuous mode .............................................34 5 White balance...................................................32 6 Film simulation.................................................
Parts of the Camera ■ Playback: Electronic Viewfinder/LCD Monitor 100-0001 3:2 F YouTube 12 / 31 / 2050 1 / 1000 8 10 : 00 AM F4.5 -1 2 3 200 1 Rating ...............................................................56 6 Playback mode indicator...................................56 2 Red-eye removal indicator ................................73 7 Mark for upload to ............................................77 3 Silent mode indicator .................................30, 80 8 Photobook assist indicator ...
First Steps Attaching the Strap Attach the strap clips to the camera and then attach the strap. 1 Open a strap clip. 3 Pass the clip through the eyelet. Rotate the clip fully through the eyelet until it clicks closed. 4 Attach a protective cover. Q Keep the tool in a safe place. You will need it to open the strap clips when removing the strap. 2 Place the strap clip on an eyelet. First Steps Use the clip attaching tool to open a strap clip as shown.
Attaching the Strap 5 Insert the strap. Insert the strap through a protective cover and strap clip. 6 Fasten the strap. Fasten the strap as shown. Repeat Steps 5–6 for the second eyelet. Q To avoid dropping the camera, be sure the strap is correctly secured.
Attaching a Lens Lenses attach as described below. Q Care is required to prevent dust entering the camera while attaching and removing lenses. 1 Remove the body and rear caps. Remove the body cap from the camera and the rear cap from the lens. Lens release button Q To prevent dust accumulating inside the camera, replace the body cap when no lens is attached. Q Do not touch the camera’s internal parts. 2 Attach the lens.
Charging the Battery The battery is not charged at shipment. Charge the battery before use. 1 Place the battery in the charger. Place the battery in the supplied battery charger as shown. Charge lamp Battery charger 2 Plug the charger in. Plug the charger into a power outlet. The charging indicator will light. The Charging Indicator The charging indicator shows battery charge status as follows: Charging indicator Arrow On Battery not inserted. Battery fully charged. Battery charging.
Inserting the Battery and a Memory Card The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC memory cards (sold separately). After charging the battery, insert the battery and memory card as described below. 1 Open the battery-chamber cover. 2 Insert the battery. Insert the battery as shown inside the battery chamber, using the battery to keep the battery latch pressed to one side. Arrow Q Do not open the battery-chamber cover when the camera is on.
Inserting the Battery and a Memory Card 3 Insert the memory card. Holding the memory card in the orientation shown at right, slide it in until it clicks into place at the back of the slot. Click Q Be sure card is in the correct orientation; do not insert at an angle or use force. Q SD/SDHC/SDXC memory cards can be locked, making it impossible to format the card or to Write-protect switch record or delete images. Before inserting a memory card, slide the writeprotect switch to the unlocked position.
Inserting the Battery and a Memory Card Removing the Battery and Memory Card Before removing the battery or memory card, turn the camera off and open the battery-chamber cover. Battery latch To remove the memory card, press it in and release it slowly. The card can then be removed by hand. When a memory card is removed, the card could come out of the slot too quickly. Use your finger to hold it and gently release the card.
Inserting the Battery and a Memory Card ■ Compatible Memory Cards FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_ cameras/compatibility/. Operation is not guaranteed with other cards. The camera can not be used with xD-Picture Cards or MultiMediaCard (MMC) devices.
Turning the Camera on and Off Rotate the ON/OFF switch to ON to turn the camera on. Select OFF to turn the camera off. Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder. Keep the lens and viewfinder clean. First Steps R Press the a button to start playback. Press the shutter button halfway to return to shooting mode.
Basic Setup A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as described below (you can reset the clock or change languages at any time using the F DATE/TIME or L a options in the setup menu; for information on displaying the setup menu, see page 80). 1 Choose a language. Highlight a language and press MENU/OK. START MENU ENGLISH R Press DISP/BACK to skip the current step. Any steps you skip will be displayed the next time the camera is turned on.
Choosing a Display The camera is equipped with a hybrid optical/electronic viewfinder (OVF/EVF) and an LCD monitor (LCD). Press VIEW MODE to choose a display.
Choosing a Display Using the Hybrid Viewfinder Use the viewfinder selector to choose between optical and electronic viewfinders. Keep the selector pressed up to choose the optical viewfinder display zoom ratio. 0.1 0.5 1.0 P 2000 1.5 F5.6 2.0 3.0 Choosing a Display Choose a display according to the task. Display Optical viewfinder (OVF) 0.1 0.5 5.0 10 200 Optical viewfinder display P 1.0 2000 1.5 2.0 F5.6 3.0 5.
The DISP/BACK Button The DISP/BACK button controls the display of indicators in the viewfinder and LCD monitor. ■ LCD Monitor: Shooting ■ Optical Viewfinder: Shooting F 100 Detailed display Standard display 000100 F 1.5 F5.6 2.0 3.0 5.0 10 200 0.1 0.5 1.0 P 2000 Standard display 1.5 F5.6 2.0 3.0 5.0 10 200 P 1 Custom display 2000 5.6 F 200 0.1 0.5 ■ Electronic Viewfinder: Shooting 100 100 1.0 2000 1.5 2.0 F5.6 3.0 0.1 0.5 5.0 10 200 Standard display P 1.0 2000 1.
The DISP/BACK Buttion ■ Electronic Viewfinder/LCD Monitor: Playback Indicators displayed Indicators hidden Favorites 3:2 F 12 / 31 / 2050 1 / 1000 3 10 : 00 AM F4.5 Photo information 100-0001 100-0001 -1 2 3 200 12 / 31 / 2050 10 : 00 AM 3:2 F ISO 200 1/1000 F4.5 : : OFF : : -1 2 3 12 / 31 / 2050 10 : 00 AM 100-0001 Q The optical viewfinder can not be used for playback. Histograms Histograms show the distribution of tones in the image.
Power Management The setup menu contains the following power management options (P 81). For information on using the setup menu, see page 79. • U POWER SAVE MODE: Select ON to increase the number of photographs that can be taken with a fully-charged battery. • H QUICK START MODE: Select ON to reduce camera startup time. H QUICK START MODE OFF ON Startup time Standby time Endurance 300 shots Startup time Standby time 0.5 s 24 minutes Endurance 150 shots ON 1.
Taking Photographs Program AE (P) To allow the camera to adjust both shutter speed and aperture for optimal exposure, rotate the shutter speed dial and lens aperture ring to A. P will appear in the display. A 16 11 8 5.6 Q If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show “– – –”. P 2000 F5.6 200 P 2000 Optical viewfinder F5.
Shutter-Priority AE (S) To adjust shutter speed manually while letting the camera select aperture for optimal exposure, rotate the lens aperture ring to A and use the shutter speed dial (if A is currently selected for shutter speed, press the dial release while rotating the shutter speed dial). S will appear in the display. S 2000 F5.6 16 11 8 5.6 200 Optical viewfinder S 2000 F5.
Aperture-Priority AE (A) To adjust aperture manually while letting the camera select shutter speed for optimal exposure, rotate the shutter speed dial to A and use the lens aperture ring. A will appear in the display. Q If the correct exposure can not be achieved at the selected aperture, the shutter speed will be displayed in red when the shutter button is pressed halfway. Adjust aperture until the correct exposure is achieved.
Manual Exposure (M) Exposure can be altered from the value suggested by the camera by rotating both the shutter speed dial and aperture ring to settings other than A (if A is currently selected for shutter speed, press the dial release while rotating the shutter speed dial). M will appear in the display. A 2000 F5.6 M 200 Optical viewfinder 2000 R The manual exposure display includes an exposure indicator that shows the amount the picture would be under- or over-exposed at current settings.
Long Time-Exposures (T/B) Select a shutter speed of T (time) or B (bulb) for long time-exposures. R Use of a tripod is recommended to prevent the camera from moving during the exposure. R To reduce “noise” (mottling) in long time-exposures, select ON for K LONG EXPOSURE NR in the shooting menu. Note that this may increase the time needed to record images after shooting. Time (T) 1 Rotate the shutter speed dial to T. Bulb (B) 1 Rotate the shutter speed dial to B.
Exposure Compensation Rotate the exposure compensation dial to adjust exposure when photographing very bright, very dark, or high-contrast subjects. The effect is visible in the LCD monitor and electronic viewfinder; when using the optical viewfinder, use the exposure indicator to check exposure. Exposure compensation indicator 000100 F P 2000 F5.6 200 P 2000 F5.6 EVF Choose positive values (+) to increase exposure Choose negative values (–) to reduce exposure 200 P 1 2000 5.
Focusing and Taking Pictures Press the shutter button halfway to focus and the rest of the way down to shoot. 1 Focus. Frame the picture with your subject in the center focus area and press the shutter button halfway to focus. R If the subject is poorly lit, the AF-assist illuminator may light (P 72). If the camera is able to focus, it will beep twice and focus area will glow green. Focus and exposure will lock while the shutter button is pressed halfway.
More on Photography F Macro Mode (Close-ups) To focus at short distances, press the selector up (MACRO) and select F. If the optical viewfinder is on, the camera will automatically switch to the electronic viewfinder (because of parallax, the optical viewfinder is not recommended). To exit macro mode, press the selector up left and select OFF.
White Balance For natural colors, select D WHITE BALANCE in the shooting menu to display the following options, then use the selector to highlight an option that matches the light source and press MENU/OK. The dialog shown at bottom right will be displayed; use the selector to fine-tune white balance or press DISP/BACK to exit without finetuning (for an explanation of “white balance,” see the Glossary on page 109).
White Balance h: Custom White Balance Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will be displayed; frame a white object so that it fills the display and press the shutter button all the way down to measure white balance (to select the most recent custom value and exit without measuring white balance, press DISP/BACK, or press MENU/OK to select the most recent value and display the fine-tuning dialog).
I Continuous Shooting (Burst Mode) Capture motion in a series of pictures. 1 Press the DRIVE button to display drive options. 6fps 3fps CONTINUOUS 2 Press the selector up or down to choose from frame rates of approximately 6 fps (frames per second) and 3 fps, and press left or right to choose the number of shots per burst. 3 Press the shutter button halfway to focus. 34 4 Press the shutter button the rest of the way down to start shooting.
Bracketing Automatically vary settings over a series of pictures. 1 Press the DRIVE button to display drive options and press the selector up or down to highlight one of the following: Option ±1 ±2/ 3 ±1/ 3 AE BKT More on Photography Description Press the selector left or right to highlight a bracketing amount.
Multiple Exposures Create a photograph that combines two exposures. 1 Select ON for n MULTIPLE EXPOSURE in 4 Take the second shot. the shooting menu. 2 Take the first shot. 5 Press MENU/OK to create the multiple 3 Press MENU/OK. You will be prompted to take the second shot. R To return to Step 2 and retake the first shot, press the selector left. To save the first shot and exit without creating a multiple exposure, press DISP/ BACK.
Panoramas Follow an on-screen guide to create a panorama. 1 Press the DRIVE button to display 5 Pan the camera in the direction shown by the drive options. Press the selector up or down to highlight r (MOTION PANORAMA) and press MENU/OK. arrow. Shooting ends automatically when the camera is panned to the end of the guides and the panorama is complete. MOTION PANORAMA through which you will pan the camera while shooting, press the selector left. Highlight a size and press MENU/OK.
Panoramas Q Panoramas are created from multiple frames; exposure for the entire panorama is determined by the first frame. The camera may in some cases record an greater or lesser angle than selected or be unable to stitch the frames together perfectly. The last part of the panorama may not be recorded if shooting ends before the panorama is complete. Q Shooting may be interrupted if the camera is panned too quickly or too slowly. Panning the camera in a direction other than that shown cancels shooting.
F Recording High-Definition (HD) Movies Record short high-definition movies. Sound is recorded in stereo via the built-in microphone; during recording, do not cover the microphone or use the viewfinder selector, which is located next to the microphone. 1 Press the DRIVE button to display drive options. Press the selector up or down to highlight F (MOVIE) and press MENU/OK. Q If the optical viewfinder is on, the camera will automatically switch to the electronic viewfinder.
F Recording High-Definition (HD) Movies Before Recording Before recording, choose a frame size of i 1920 (1,920 × 1,080, or Full HD) or h 1280 (1,280 × 720, or HD) using the W MOVIE MODE option in the shooting menu (P 73), adjust aperture (P 26), white balance (P 32), film simulation (P 51), and exposure compensation (P 29), and select a focus mode (P 45). R To increase zoom by 3 × for a focal length equivalent to 105 mm (35 mm format), press the k button before recording begins. Press n to cancel zoom.
h Using the Self-Timer Use the timer for self-portraits or to prevent blur caused by camera shake. P SHOOTING MENU 1 Press MENU/OK in shooting mode to display the shooting menu. Press ISO IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION FILM SIMULATION BKT SELF-TIMER the selector up or down to highlight B SELF-TIMER and press MENU/ OK. 200 3:2 F OFF EXIT 2 Press the selector up or down to highlight one of the following options and press MENU/OK to select.
h Using the Self-Timer 4 Press the shutter button the rest of the way down to start the timer. The display in the monitor shows the number of seconds remaining until the shutter is released. To stop the timer before the picture is taken, press DISP/BACK. The self-timer lamp on the front of the camera will blink immediately before the picture is taken. If the two-second timer is selected, the self-timer lamp will blink as the timer counts down.
Focus/Exposure Lock To compose photographs with off-center subjects: 1 Focus: Position the subject in the focus frame and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while the shutter button is pressed halfway (AF/AE lock). P 2000 F5.6 200 2 Recompose: Keep the shutter button pressed halfway or keep the AFL/AEL button pressed.
Focus/Exposure Lock Autofocus Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed below. • Very shiny subjects such as mirrors or car bodies. • Fast-moving subjects. • • • • Subjects photographed through a window or other reflective object. Dark subjects and subjects that absorb rather than reflect light, such as hair or fur. Insubstantial subjects, such as smoke or flame.
Focus Mode Focus distance (red bar) A Reduce focus distance 16 11 8 5.6 4 2.8 Increase focus distance Manual focus mode icon 0.1 0.5 M 1.0 2000 1.5 2.0 F5.6 1.0 3.0 5.0 10 200 Manual focus indicator 1.5 2.0 3.0 Depth of field (white bar) More on Photography Use the focus mode selector to choose how the camera focuses. • S (single AF): Focus locks while the shutter button is pressed halfway. Choose for stationary subjects.
Focus Mode Manual Focus Pressing the center of the command dial magnifies the view in the electronic viewfinder or LCD monitor for precise focus. To scroll to other areas of the frame, press the AF button and use the selector. 0.1 0.5 M 46 1.0 2000 1.5 2.0 F5.6 3.0 5.0 10 200 0.1 0.5 M 1.0 2000 1.5 2.0 F5.6 3.0 5.
Focus Frame Selection When t AREA is selected for F AF MODE in the shooting menu and S is selected for focus mode, the electronic viewfinder and LCD monitor offer a choice of 49 focus points and the optical viewfinder a choice of 25, allowing photographs to be composed with the main subject positioned almost anywhere in the frame. To position the focus frame, press the AF button and use the selector (the focus frame can be returned to the center by pressing MENU/OK).
Sensitivity “Sensitivity” refers to the camera’s sensitivity to light. Choose from values between L (100) (ISO 100) and H (25600) (ISO 25600). Higher values can be used to reduce blur when lighting is poor, while lower values allow slower shutter speeds or wider apertures in bright light; note, however, that mottling may appear in pictures taken at high sensitivities, particularly at H (25600), while choosing L (100) reduces dynamic range.
Metering To choose how the camera meters exposure, press the AE button to display metering options. Use the selector to highlight an option and press AE to select. Mode PHOTOMETRY MULTI OVF EVF/LCD More on Photography Description The camera instantly determines exposure based on an analysis of o composition, color, and brightness distribution. Recommended in (MULTI) most situations. The camera meters lighting conditions in an area at the center of the frame equivalent to 2% of the total.
The Fn Button The role played by the Fn button can be selected using the F Fn BUTTON option in the shooting menu (P 70). The options available include multiple exposure (P 36), depth-of-field preview (P 26), the self-timer (P 41), sensitivity (P 48), image size (P 67), image quality (P 67), dynamic range (P 68), film simulation (P 51), white balance (P 32), AF mode (P 69), movie recording (P 39), RAW/JPEG toggle (P 53), and custom settings (P 52).
Film Simulation Simulate the effects of different kinds of film, including black-and-white (with or without color filters). 1 Press MENU/OK in shooting mode to display the shooting menu. Press the selector up or down to highlight P FILM SIMULATION and press MENU/OK. P SHOOTING MENU ISO IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION FILM SIMULATION BKT SELF-TIMER 200 3:2 F OFF EXIT 2 Press the selector up or down to highlight one of the following options and press MENU/OK to select.
Saving Settings Save up to three sets of custom camera settings for commonly-encountered situations. Saved settings can be recalled using the u SELECT CUSTOM SETTING option in the shooting menu. P SHOOTING MENU 1 Press MENU/OK in shooting mode to display the shooting menu. Press SELECT CUSTOM SETTING EDIT/SAVE CUSTOM SETTING AF MODE CORRECTED AF FRAME FOCAL LENGTH SETTING SHOOT WITHOUT LENS Fn BUTTON the selector up or down to highlight K EDIT/SAVE CUSTOM SETTING and press MENU/OK.
Recording Pictures in RAW Format To toggle RAW image quality on or off for a single shot, assign RAW to the Fn button (P 50). If a JPEG option is currently selected for image quality, pressing the Fn button temporarily selects the equivalent JPEG+RAW option. If a JPEG+RAW option is currently selected, pressing the Fn button temporarily selects the equivalent JPEG option, while if RAW is selected, pressing the Fn button temporarily selects FINE.
N Flash Photography Optional EF-42, EF-20, and EF-X20 shoe-mounted flash units (P 97) can be used for additional lighting when shooting at night or indoors under low light. See the manual provided with the flash unit for details. To choose the flash mode for the optional flash unit, select I FLASH MODE in the shooting menu. The options shown below will be displayed; press the selector up or down to highlight an option and press MENU/OK to select.
Flash Photography Flash Sync Speed The flash will synchronize with the shutter at shutter speeds of 1/180 s or slower. The Sync Terminal Use the sync terminal to connect flash units that require a sync cable. Third-Party Flash Units Do not use third-party flash units that apply over 300 V to the camera hot shoe.
Viewing Pictures Viewing Pictures Full Frame Pictures can be viewed in the electronic viewfinder or LCD monitor. When taking important pictures, take a test shot and check the results. To view pictures full frame, press a. 100-0001 Deleting Pictures To delete the current picture, press the b button. The following dialog will be displayed. ERASE OK? 1 / 1000 F4.5 -1 2 3 Additional pictures can be viewed by pressing the selector left or right or rotating the command dial.
Viewing Pictures Full Frame Viewing Photo Information The photo information display changes each time the selector is pressed up. 100-0001 3:2 F 12 / 31 / 2050 1 / 1000 10 : 00 AM F4.5 D-RANGE COLOR HIGH LIGHT TONE SHADOW TONE SHARPNESS FILM SIM. WHITE BALANCE : 100 : STD : STD : STD : STD : PROVIA : AUTO -1 2 3 200 Basic data Zoom indicator Details, page 1 COLOR SPACE METERING EXPOSURE MODE LENS FOCAL LENGTH FLASH MODE : sRGB : PATTERN : PROGRAM : 18mm F2.
Viewing Pictures Full Frame Multi-Frame Playback To change the number of images displayed, press n when a picture is displayed full frame. Press n to view more images. 100-0001 Press k to view fewer images. Use the selector to highlight images and press MENU/OK to view the highlighted image full frame. In the nine- and hundred-frame displays, press the selector up or down to view more pictures.
Viewing Movies During playback, movies are displayed as shown at right. The following operations can be performed while a movie is displayed: Description Press the selector down to start playback. Press again to pause. While playback is Start/pause playback paused, you can press the selector left or right to rewind or advance one frame at a time. End playback Press the selector up to end playback. Press the selector left or right to adjust playback speed during playback.
Image Search Follow the steps below to search for pictures. 1 Press MENU/OK during playback to display the playback menu. Press the selector up or down to highlight b IMAGE SEARCH and press MENU/OK. 2 Highlight an option and press MENU/OK. Option BY DATE BY FACE BY I FAVORITES BY TYPE OF DATA BY UPLOAD MARK Description Search by date. Search for pictures that include faces. Search by rating. Find all still pictures, all movies, all pictures taken in burst mode, or all RAW pictures.
m PhotoBook Assist Create books from your favorite photos. Creating a PhotoBook 1 Select NEW BOOK for m PHOTOBOOK ASSIST in the playback menu (P 77) and choose from the following options: • SELECT FROM ALL: Choose from all available pictures. • SELECT BY IMAGE SEARCH: Choose from pictures matching selected search conditions (P 60). R Neither photographs a or smaller nor movies can be selected for photobooks. lector up to select or deselect.
m PhotoBook Assist Viewing Photobooks Highlight a book in the photobook assist menu and press MENU/OK to display the book, then press the selector left or right to scroll through the pictures. Editing and Deleting Photobooks Display the photobook and press MENU/OK. The following options will be displayed; select the desired option and follow the on-screen instructions. • EDIT: Edit the book as described in “Creating a PhotoBook” (P 61). • ERASE: Delete the book.
Viewing Panoramas If you press the selector down when a panorama is displayed full frame, the camera will play back the picture from left to right or from bottom to top. Press the selector down to pause and resume playback, or press the dial up to return to full-frame playback. To rewind or advance one frame at a time, press the selector left or right while playback is paused.
Viewing Pictures Taken in a Single Burst When a picture taken in continuous shooting mode is displayed full frame, the first picture in the current burst can be viewed by pressing the selector down (burst mode playback). Press the dial right to view pictures in the order recorded, left to view pictures in reverse order. Keep the dial pressed to scroll rapidly to the desired frame. To exit, press DISP/BACK.
x Deleting Pictures The A ERASE option in the playback menu can be used to delete individual pictures, multiple selected pictures, or all pictures. Note that deleted pictures can not be recovered. Copy important pictures to a computer or other storage device before proceeding. Press MENU/OK during playback to display the playback menu, then press the selector up or down to highlight A ERASE and press right to display the following options.
Creating JPEG Copies of RAW Pictures RAW pictures store information on camera settings separately from the data captured by the camera image sensor. Using the j RAW CONVERSION option in the playback menu, you can create JPEG copies of RAW pictures using different options for the settings listed below. The original image data are unaffected, allowing a single RAW image to be processed in a multitude of different ways.
Menus Using the Menus: Shooting Mode The shooting menu is used to adjust settings for a wide range of shooting conditions. To display the shooting menu, press MENU/OK in shooting mode. Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete.
Using the Menus: Shooting Mode U DYNAMIC RANGE (defaults to A) Control contrast. Choose lower values to increase contrast when shooting indoors or under overcast skies, higher values to reduce loss of detail in highlights and shadows when photographing high-contrast scenes.
Using the Menus: Shooting Mode q SHARPNESS Sharpen or soften outlines. (defaults to STANDARD) r HIGHLIGHT TONE Adjust the appearance of highlights. (defaults to STANDARD) s SHADOW TONE Adjust the appearance of shadows. (defaults to STANDARD) h NOISE REDUCTION Reduce noise in pictures taken at high sensitivities. (defaults to STANDARD) K LONG EXPOSURE NR Select ON to reduce mottling in long time-exposures (P 28).
Using the Menus: Shooting Mode (defaults to OFF) G CORRECTED AF FRAME If ON is selected, a second focus frame for focus distances of about 80 cm (2.6 ft) will be added to the display in the optical viewfinder. The focus frame for the current focus distance is displayed in green when the shutter button is pressed halfway. ON OFF Focus frame for focus distance of infinity Focus frame P 2000 F5.6 200 P 2000 F5.6 200 Focus frame for focus distance of about 80 cm (2.
Using the Menus: Shooting Mode v DISP. CUSTOM SETTING Choose the items displayed in the optical viewfinder or in the electronic viewfinder and LCD monitor (P 21).
Using the Menus: Shooting Mode C AF ILLUMINATOR If ON is selected, the AF-assist illuminator will light to assist autofocus. (defaults to ON) R The AF-assist illuminator turns off automatically in silent mode. Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro mode, try increasing the distance to the subject. Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
Using the Menus: Shooting Mode B RED EYE REMOVAL Choose ON to remove red-eye effects caused by the flash. (defaults to OFF) R Red-eye reduction is performed only when a face is detected. R Red-eye removal is not available with RAW images. n SAVE ORG IMAGE Choose ON to save unprocessed copies of pictures taken using B RED EYE REMOVAL. (defaults to OFF) W MOVIE MODE Choose a frame size for movie recording (P 39).
Using the Menus: Playback Mode To display the playback menu, press MENU/OK in playback mode. Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete. PLAYBACK MENU RAW CONVERSION ERASE CROP RESIZE PROTECT IMAGE ROTATE RED EYE REMOVAL EXIT Playback Menu Options j RAW CONVERSION Create JPEG copies of RAW pictures (P 56). A ERASE Delete all or selected pictures (P 65).
Using the Menus: Playback Mode e RESIZE Create a cropped copy of the current picture. 1 Display the desired picture. 2 Select e RESIZE in the playback menu. 3 Highlight a size and press MENU/OK to display a confirmation dialog. 4 Press MENU/OK again to save the resized copy to a separate file. R The sizes available vary with the size of the original image. D PROTECT Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK. • FRAME: Protect selected pictures.
Using the Menus: Playback Mode B RED EYE REMOVAL Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create a copy with reduced red-eye. 1 Display the desired picture. 2 Select B RED EYE REMOVAL in the playback menu. 3 Press MENU/OK. R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on the scene.
Using the Menus: Playback Mode m PHOTOBOOK ASSIST Create books from your favorite photos (P 61). j MARK FOR UPLOAD TO Select pictures for upload to YouTube or Facebook using MyFinePix Studio (Windows only). 1 Select YouTube to choose movies for upload to YouTube, FACEBOOK to choose photos and movies for upload to Facebook. 2 Press the selector left or right to display pictures and press MENU/OK to select or deselect. Press DISP/BACK to exit when all the desired pictures are selected.
Using the Menus: Playback Mode J DISP ASPECT Choose how High Definition (HD) devices display pictures with an aspect ratio of 3 : 2 (this option is available only when an HDMI cable is connected). Select 16 : 9 to display the image so that it fills the screen with its top and bottom cropped out, 3 : 2 to display the entire image with black bands at either side. 16 : 9 3: 2 16 : 9 I PLAYBACK VOLUME Control the volume for movie playback.
The Setup Menu Using the Setup Menu 1 Display the setup menu. 1.1 Press MENU/OK to display the menu for the current mode. 1.2 Press the selector left to highlight the tab for the current menu. 1.3 Press the selector down to highlight Z. SET-UP DATE/TIME TIME DIFFERENCE RESET SILENT MODE FRAME NO. FOCUS RING ENGLISH OFF CONT. EXIT Tab Menus 1.4 Press the selector right to place the cursor in the setup menu. 2 Adjust settings.
The Setup Menu Setup Menu Options F DATE/TIME Set the camera clock (P 18). N TIME DIFFERENCE (defaults to h) Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between local time and your home time zone: 1 Highlight g LOCAL and press the selector right. 2 Use the selector to choose the time difference between local time and your home time zone. Press MENU/OK when settings are complete.
The Setup Menu (defaults to CONTINUOUS) B FRAME NO. New pictures are stored in image files named using a four-digit file number assigned by adding one to the Frame number last file number used. The file number is displayed during playback as shown at right. B FRAME NO. con100-0001 trols whether file numbering is reset to 0001 when a new memory card is inserted or the current memory card is formatted.
The Setup Menu (defaults to 2 MIN) M AUTO POWER OFF Choose the length of time before the camera turns off automatically when no operations are performed. Shorter times reduce the drain on the battery; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera turns off automatically even when OFF is selected. G OPERATION VOL. (defaults to c) Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF (mute) to disable control sounds.
The Setup Menu J COLOR SPACE Choose the gamut of colors available for color reproduction. Option sRGB Recommended in most situations. Adobe RGB For commercial printing. c GUIDANCE DISPLAY Choose whether to display tool tips. M FOCUS SCALE UNITS Choose the units used for the focus distance indicator (P 45). (defaults to sRGB) Description (defaults to ON) (defaults to METERS METERS)) O BACKGROUND COLOR Choose a color scheme. K FORMAT Select OK to format the memory card.
Connections Viewing Pictures on TV To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately from third-party suppliers; note that the TV can only be used for playback, not shooting). 1 Turn the camera off. 2 Connect the cable as shown below. Insert into HDMI connector Insert into HDMI mini connector R Be sure the connectors are fully inserted. 3 Tune the television to the HDMI input channel. See the documentation supplied with the television for details.
Printing Pictures via USB If the printer supports PictBridge, the camera can be connected directly to the printer and pictures can be printed without first being copied to a computer. Note that depending on the printer, not all the functions described below may be supported. Connecting the Camera 1 Connect the supplied USB cable as shown and turn the printer on. Printing Selected Pictures 1 Press the selector left or right to display a picture you wish to print.
Printing Pictures via USB Printing the Date of Recording To print the date of recording on pictures, press DISP/BACK in the PictBridge display and select PRINT WITH DATE s (to print pictures without the date of recording, select PRINT WITHOUT DATE). To ensure that the date is correct, set the camera clock before taking pictures. Some printers do not support date printing. See the printer manual for details.
Printing Pictures via USB During Printing The message shown at right is displayed during printing. Press DISP/BACK to cancel before all pictures are printed (depending on the printer, printing may end before the current picture has printed). PRINTING CANCEL If printing is interrupted, turn the camera off and then on again. Disconnecting the Camera Confirm that the above message is not displayed and turn the camera off. Disconnect the USB cable.
Printing Pictures via USB ■ WITH DATE s/ WITHOUT DATE To modify the DPOF print order, select K PRINT ORDER (DPOF) in the playback menu and press the selector up or down to highlight WITH DATE s or WITHOUT DATE. PLAYBACK MENU WITH DATE s: Print date of recording on pictures. SLIDE SHOW PHOTOBOOK ASSIST WITH DATE s MARK FOR UPLOAD TO WITHOUT DATE IMAGE SEARCH RESET ALL PRINT ORDER (DPOF) DISP ASPECT PLAYBACK VOLUME WITHOUT DATE: Print pictures without date. Press MENU/OK and follow the steps below.
Printing Pictures via USB ■ RESET ALL To cancel the current print order, select RESET ALL for K PRINT ORDER (DPOF). The confirmation shown at right will be displayed; press MENU/OK to remove all pictures from the order. RESET DPOF OK? YES CANCEL R Print orders can contain a maximum of 999 pictures. RESET DPOF OK? R If a memory card is inserted containing a print order created by another camera, the message shown at right will YES NO be displayed.
Viewing Pictures on a Computer The supplied software can be used to copy pictures to a computer, where they can be stored, viewed, organized, and printed. Before proceeding, install the software as described below. Do NOT connect the camera to the computer until installation is complete.
Viewing Pictures on a Computer 3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive. Windows 7/Windows Vista If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed; click Yes (Windows 7) or Allow (Windows Vista). The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio and RAW FILE CONVERTER.
Viewing Pictures on a Computer Macintosh: Installing FinePixViewer 1 Confirm that the computer meets the following system requirements: CPU PowerPC or Intel (Core 2 Duo or better) Pre-installed copies of Mac OS X version 10.3.9–10.6 (visit http://www.fujifilm.com/support/digital_cameras/ OS compatibility/ for more information). Mac OS X version 10.7 and later not supported.
Viewing Pictures on a Computer 5 Mac OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences… from the Image Capture application menu. The Image Capture preferences dialog will be displayed; choose Other… in the When a camera is connected, open menu, then select FPVBridge in the “Applications/FinePixViewer” folder and click Open. Quit Image Capture. Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image Capture.
Viewing Pictures on a Computer Connecting the Camera 1 Find a memory card containing pictures you want to copy to the computer and insert the card into the camera (P 14). R Windows users may require the Windows CD when starting the software for the first time. Q Loss of power during transfer could result in loss of data or damage to the memory card. Insert a fresh or fully-charged battery before connecting the camera.
Viewing Pictures on a Computer Q If a memory card containing a large number of images is inserted, there may be a delay before the software starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Technical Notes Optional Accessories The camera supports a wide range of accessories from FUJIFILM and other manufacturers. Accessories from FUJIFILM The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/ products/digital_cameras/index.html.
Optional Accessories Protector Filter PRF-52: Protector Filter (diameter 52 mm). PRF-39: Protector Filter (diameter 39 mm). Grips HG-XPro1: Features an improved grip. Shoe-mounted flash units EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide Number of 20/66 (ISO 100, m/ft.) and supports TTL flash control. The flash head can be rotated upwards 90° for bounce lighting. EF-42: This clip-on flash unit (powered by four AA batteries) has a Guide Number of 42/138 (ISO 100, m/ft.
Optional Accessories Recommended Third-Party Accessories Diopter adjustment lenses COSINA diopter adjustment lenses are recommended for use with this camera.
Optional Accessories Connecting the Camera to Other Devices ■ Printing X-Pro1 ■ Flash Photography USB cable (supplied) PictBridge-compatible printer EF-20 shoe mount EF-42 shoe mount flash * flash * † SD/SDHC/SDXC memory card † EF-X20 shoe mount flash * ■ Lens Printer † USB cable (supplied) SD card slot or card reader XF35mmF1.4 R * XF60mmF2.4 R Macro * ■ Audio/Visual HDMI cable † Technical Notes XF18mmF2 R * ■ Computer Related Computer † * Available separately from FUJIFILM.
Caring for the Camera To ensure continued enjoyment of the product, observe the following precautions. Storage and Use If the camera will not be used for an extended period, remove the battery and memory card.
Cleaning the Image Sensor Multiple photographs marred by spots or blotches in identical locations may indicate the presence of dust on the camera image sensor. Clean the sensor using the V SENSOR CLEANING option in the setup menu (P 82); if the problem persists, you can clean the sensor manually as described below. Note that there will be a charge to repair or replace the image sensor if it is damaged during cleaning. 1 Use a blower (not a brush) to remove dust from the sensor.
Troubleshooting Problems and Solutions Power and Battery Problem The camera does not turn on. The battery runs down quickly. The camera turns off suddenly. Charging does not start. Charging is slow. The charging lamp lights, but the battery does not charge. Solution The battery is exhausted exhausted:: Charge the battery ((P P 12) or insert a fully-charged spare battery ((P P 13). The battery is inserted incorrectly: incorrectly: Reinsert in the correct orientation ((P P 13).
Problems and Solutions Shooting Problem No picture is taken when the shutter button is pressed. • • • • • • • Solution Memory is full: full: Insert a new memory card or delete pictures (P (P 14, 65). Memory is not formatted: formatted: Format the memory card (P (P 83). There is dirt on the memory card contacts contacts:: Clean the contacts with a soft, dry cloth. The memory card is damaged damaged:: Insert a new memory card ((P P 14).
Problems and Solutions Problem The flash does not fully light the subject. Pictures are blurred. Pictures are mottled. • • • • • • • • • Solution The subject is not in range of the flash ash:: Position the subject in range of the flash. The flash window is obstructed obstructed:: Hold the camera correctly. Shutter speed is faster than 1/180 ss:: Choose a slower shutter speed ((P P 25, 27). The lens is dirty dirty:: Clean the lens ((P P xi). The lens is blocked blocked:: Keep objects away from the lens.
Problems and Solutions Connections/Miscellaneous Problem No picture or sound. Be sure the camera and computer are correctly connected ((P P 94).). Use the bundled software to transfer pictures ((P P 90).). • The camera is not properly connected connected:: Connect the camera correctly ((P P 85).). • The printer is off: Turn the printer on. The printer is not PictBridge compatible. • Temporary camera malfunction: malfunction: Remove and reinsert the battery ((P P 13, 15).
Warning Messages and Displays The following warnings appear in the display. Warning B (red) A (blinks red) k s (displayed in red with red focus frame) Aperture or shutter speed displayed in red FOCUS ERROR TURN OFF THE CAMERA AND TURN ON AGAIN LENS CONTROL ERROR LENS ERROR BUSY CARD NOT INITIALIZED PROTECTED CARD 106 Description Low battery. Charge the battery ((P P 12) or insert a fully-charged spare battery ((P P 13). Battery exhausted.
Warning Messages and Display Warning CARD ERROR b MEMORY FULL NO CARD WRITE ERROR FRAME NO. FULL TOO MANY FRAMES Troubleshooting READ ERROR Description • The memory card is not formatted for use in the camera camera:: Format the card (P (P 83). • The memory card contacts require cleaning or the memory card is damaged damaged:: Clean the contacts with a soft, dry cloth. If the message is repeated, format the card (P (P 83). If the message persists, replace the card.
Warning Messages and Display Warning PROTECTED FRAME CAN NOT CROP m CANNOT EXECUTE F CANNOT EXECUTE CAN NOT ROTATE F CAN NOT ROTATE Description An attempt was made to delete or rotate to a protected picture. Remove protection and try again ((P P 75). The picture is damaged or was not created with the camera. Red-eye removal can not be applied to pictures created with other devices. Red-eye removal can not be applied to movies. The selected picture can not be rotated. Movies can not be rotated.
Appendix Glossary DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders” stored on a memory card. The information in the order includes the pictures to be printed and the number of copies of each picture. EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount of light that enters the camera while the image sensor is exposed.
Memory Card Capacity The following table shows the recording time or number of pictures available at different image sizes. All figures are approximate; file size varies with the scene recorded, producing wide variations in the number of files that can be stored. The number of exposures or length remaining may not diminish at an even rate.
Specifications System Model Effective pixels Image sensor Storage media File system File format Image size Lens mount Sensitivity Appendix Metering Exposure control Exposure compensation Shutter speed (combined mechanical and electronic shutter) X-Pro1 digital camera 16.3 million 23.6 mm × 15.
Specifications System Continuous Focus LCD monitor Movies Approximately 6 or 3 fps • Mode Mode:: Single or continuous AF; manual focus with focus ring • Focus-area selection selection:: Multi, area with focus area size selection; 49 (7 × 7) areas available in electronic viewfinder and LCD monitor, 25 (5 × 5) areas available in optical viewfinder • Autofocus system: system: Contrast-detect TTL AF with AF-assist illuminator Custom, color temperature selection, auto, direct sunlight, shade, daylight fluorescent
Specifications Power supply/other Power supply NP-W126 rechargeable battery Battery life (approximate Battery type Approximate number of frames number of frames that can NP-W126 (type supplied with camera) 300 be taken with a fully-charged CIPA standard, measured using battery supplied with camera and SD memory card. battery) Note:: Number of shots that can be taken with battery varies with battery charge level and will decline at low Note temperatures. Camera size (W × H × D) 139.5 mm × 81.8 mm × 42.
Specifications NP-W126 rechargeable battery Nominal voltage 7.2 V DC Nominal capacity 1,260 mAh Operating temperature 0 °C to +40 °C/+32 °F to +104 °F Dimensions (W × H × D) 36.4 mm × 47.1 mm × 15.7 mm/1.4 in. × 1.9 in. × 0.6 in. Weight Approx. 47 g/1.7 oz. BC-W126 battery charger Rated input Input capacity Rated output Supported batteries Charging time Operating temperature Dimensions (W × H × D) Weight 100 V – 240 V AC, 50/60 Hz 13 –21 VA 8.4 V DC, 0.6 A NP-W126 rechargeable batteries Approx.
Specifications ■ Notices • Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/ digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual. • Although the electronic viewfinder and LCD monitor are manufactured using advanced high-precision technology, small bright points and anomalous colors may appear, particularly in the vicinity of text.
Restrictions on Camera Settings The options available in each shooting mode are listed below.
Restrictions on Camera Settings Option U DYNAMIC RANGE P FILM SIMULATION AUTO A B C c d e b e d f f B SELF-TIMER f COLOR q SHARPNESS r HIGHLIGHT TONE s SHADOW TONE h NOISE REDUCTION K LONG EXPOSURE NR S ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ A ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ M n ✔7 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ r ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5 ✔5 F ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Option v DISP.
Restrictions on Camera Settings Option p FLASH MODE I FLASH C AF ILLUMINATOR B RED EYE REMOVAL I FOCUS RING U POWER SAVE MODE H QUICK START MODE J COLOR SPACE 118 P ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ S ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ A ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ M ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ n r F ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔6 1 2 3 4 5 6 7 Fixed at OFF. Fixed at o (multi). Continuous AF is used when S is selected for focus mode. Fixed at Q. Center focus area selected automatically. Automatically optimized for selected shooting mode.
Memo 119
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN http://www.fujifilm.com/products/digital_cameras/index.
