BL01756-200 DIGITAL CAMERA X-E1 Owner’s Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM X-E1 digital camera and install the supplied software. Be sure that you have read and understood its contents before using the camera. EN Before You Begin First Steps Basic Photography and Playback Basic Movie Recording and Playback The Q (Quick Menu) Button More on Photography and Playback Menus For information on related products, visit our website at http://www.
For Your Safety IMPORTANT SAFETY INSTRUCTIONS • Read Instructions: All the safety and operating instructions should be read before the appliance is operated. • Retain Instructions: The safety and operating instructions should be retained for future reference. • Heed Warnings: All warnings on the appliance and in the operating instructions should be adhered to. • Follow Instructions: All operating and use instructions should be followed.
For Your Safety Service Be sure to read these notes before use Servicing: Do not attempt to service this video product Safety Notes yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to • Make sure that you use your camera correctly. Read these qualified service personnel. safety notes and your Owner’s Manual carefully before use.
For Your Safety WARNING Use only batteries or AC power adapters specified for use with this camera. Do not use voltages other than the power supply voltage shown. The use of other power sources can cause a fire. If the battery leaks and fluid gets in contact with your eyes, skin or clothing, flush the affected area with clean water and seek medical attention or call an emergency number right away. Do not use the charger to charge batteries other than those specified here.
For Your Safety ■ Battery Life At normal temperatures, the battery can be recharged about 300 times. A noticeable decrease in the length of time the battery will hold a charge indicates that it has reached the end of its service life and should be replaced. ■ Storage Performance may be impaired if the battery is left unused for extended periods when fully charged. Run the battery flat before storing it.
For Your Safety Using the Camera • Do not aim the camera at extremely bright light sources, such as the sun in a cloudless sky. Failure to observe this precaution could damage the camera image sensor. • Strong sunlight focused through the viewfinder may damage the panel of electronic viewfinder (EVF). Do not aim the electronic viewfinder at the sun. Liquid Crystal In the event that the display is damaged, care should be taken to avoid contact with liquid crystal.
For Your Safety NOTICES To prevent fire or shock hazard, do not expose the unit to rain or moisture. For Customers in Canada CAUTION: This Class B digital apparatus complies with Canadian ICES-003. Please read the “Safety Notes” and make sure you understand them before using the Disposal of Electrical and Electronic Equipment in Private Households In the European Union, Norway, Iceland and Liechtenstein: This symbol on the camera.
About This Manual Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information on specific topics, consult the sources below. Table of Contents ................................................... P x The “Table of Contents” gives an overview of the entire manual. The principal camera operations are listed here. Troubleshooting ................................................P ................................................
Product Care Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body. Any liquid on the camera should be removed immediately with a soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then gently wipe with a soft, dry cloth.
Table of Contents For Your Safety .....................................................................................ii IMPORTANT SAFETY INSTRUCTIONS.........................................ii Safety Notes .......................................................................................iii NOTICES ..............................................................................................vii About This Manual ..........................................................................
Table of Contents More on Photography and Playback Choosing an Exposure Mode ..................................................... 33 Program AE (P) ................................................................................ 33 Shutter-Priority AE (S) .................................................................. 34 Aperture-Priority AE (A)............................................................... 35 Manual Exposure (M)....................................................................
Table of Contents Menus Using the Menus: Shooting Mode ........................................... 69 Shooting Menu Options (Photographs) ............................... 69 N ISO .............................................................................................. 69 O IMAGE SIZE.............................................................................. 69 T IMAGE QUALITY .................................................................... 69 U DYNAMIC RANGE.....................................
Table of Contents The Setup Menu ............................................................................... 82 Using the Setup Menu ................................................................. 82 Setup Menu Options .................................................................... 83 F DATE/TIME ............................................................................... 83 N TIME DIFFERENCE ................................................................. 83 L a .............................
Table of Contents xiv Technical Notes Troubleshooting Optional Accessories...................................................................... 99 Accessories from FUJIFILM ......................................................... 99 Connecting the Camera to Other Devices .........................102 Caring for the Camera .................................................................103 Storage and Use ...........................................................................103 Traveling .........
Before You Begin Symbols and Conventions Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may be simplified for explanatory purposes. Supplied Accessories Before You Begin The following symbols are used in this manual: Q This information should be read before use to ensure correct operation. R Additional information that may be helpful when using the camera. POther pages in this manual on which related information may be found.
Parts of the Camera For more information, refer to the page listed to the right of each item. 1 2 3 4 5 6 7 8 9 10 2 Shutter button ................................................ 22 Exposure compensation dial ........................... 47 Shutter speed dial ..........................33, 34, 35, 36 Hot shoe...................................................28, 102 Flash ............................................................... 27 Strap eyelet ......................................................
Parts of the Camera Diopter adjustment control ............................. 18 34 Indicator lamp (see below) Eye sensor ....................................................... 17 35 AE-L/AF-L (exposure/focus lock) button .............................................................42, 45, 73 N (flash pop-up) button ................................. 27 VIEW MODE button........................................ 17 36 Q (quick menu) button....................................
Parts of the Camera Silent Mode In situations in which camera sounds or lights may be unwelcome, press the DISP/BACK button until the o icon is displayed (about a second). The camera speaker, flash, and AF-assist illuminator/self-timer lamp turn off and flash and volume settings can not be adjusted (note that silent mode can not be enabled or disabled while movie playback is in progress). Press the DISP/BACK button again to resume normal operation.
Parts of the Camera ■ Shooting: Viewfinder/LCD Monitor 100 0.1 0.5 P 1.0 2000 1.5 2.0 F5.6 3.0 5.0 10 200 F 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Flash mode ..................................................... 27 Microphone/remote release .................38, 68, 75 Macro (close-up) mode ................................... 29 Self-timer indicator ......................................... 49 Continuous mode ............................................ 54 White balance ...........................
Parts of the Camera ■ Shooting: LCD Monitor 000100 F P 1 2000 5.6 F 200 1 2 3 4 5 6 7 8 9 10 11 Flash mode ..................................................... 27 Macro (close-up) mode ................................... 29 Metering ......................................................... 48 Continuous mode ............................................ 54 Silent mode indicator ...................................4, 83 Number of available frames .......................... 113 Temperature warning.....
First Steps Attaching the Strap Attach the strap clips to the camera and then attach the strap. 1 Open a strap clip. 3 Pass the clip through the eyelet. Rotate the clip fully through the eyelet until it clicks closed. 4 Attach a protective cover. Q Keep the tool in a safe place. You will need it to open the strap clips when removing the strap. First Steps Use the clip attaching tool to open a strap clip, making sure that the tool and clip are in the orientations shown.
Attaching the Strap 5 Insert the strap. Insert the strap through a protective cover and strap clip. 6 Fasten the strap. Fasten the strap as shown. Repeat Steps 5–6 for the second eyelet. Q To avoid dropping the camera, be sure the strap is correctly secured.
Attaching a Lens Lenses attach as described below. Q Care is required to prevent dust entering the camera while attaching and removing lenses. 1 Remove the body and rear caps. Remove the body cap from the camera and the rear cap from the lens. Lens release button Q Do not touch the camera’s internal parts. 2 Attach the lens. Place the lens on mount, keeping the marks on the lens and camera aligned, and then rotate the lens until it clicks into place.
Charging the Battery The battery is not charged at shipment. Charge the battery before use. 1 Place the battery in the charger. Place the battery in the supplied battery charger as shown. Charge lamp Battery charger 2 Plug the charger in. Plug the charger into a power outlet. The charging indicator will light. The Charging Indicator The charging indicator shows battery charge status as follows: Charging indicator Arrow On Battery not inserted. Battery fully charged. Battery charging.
Inserting the Battery and a Memory Card The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC memory cards (sold separately). After charging the battery, insert the battery and memory card as described below. 1 Open the battery-chamber cover. 2 Insert the battery. Using the battery to keep the battery latch pressed to one side, insert the battery contacts first in the direction shown by the arrow. Confirm that the battery is securely latched.
Inserting the Battery and a Memory Card 3 Insert the memory card. Holding the memory card in the orientation shown at right, slide it in until it clicks into place at the back of the slot. Click Q Be sure card is in the correct orientation; do not insert at an angle or use force. Q SD/SDHC/SDXC memory cards can be locked, making it impossible to format the card or to Write-protect switch record or delete images. Before inserting a memory card, slide the writeprotect switch to the unlocked position.
Inserting the Battery and a Memory Card Removing the Battery and Memory Card Before removing the battery or memory card, turn the camera off and open the battery-chamber cover. Battery latch To remove the memory card, press it in and release it slowly. The card can then be removed by hand. When a memory card is removed, the card could be ejected too quickly. Use your finger to hold it and gently release the card.
Inserting the Battery and a Memory Card ■ Compatible Memory Cards FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_ cameras/compatibility/. Operation is not guaranteed with other cards. The camera can not be used with xD-Picture Cards or MultiMediaCard (MMC) devices.
Turning the Camera on and Off Rotate the ON/OFF switch to ON to turn the camera on. Select OFF to turn the camera off. Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder. Keep the lens and viewfinder clean. First Steps R Press the a button to start playback. Press the shutter button halfway to return to shooting mode.
Basic Setup A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as described below (you can reset the clock or change languages at any time using the F DATE/ TIME or L a options in the setup menu; for information on displaying the setup menu, see page 83). 1 Choose a language. Highlight a language and press MENU/OK. START MENU ENGLISH R Press DISP/BACK to skip the current step. Any steps you skip will be displayed the next time the camera is turned on.
Choosing a Display The camera is equipped with an electronic viewfinder (EVF) and an LCD monitor (LCD). Press VIEW MODE to choose a display.
Choosing a Display Focusing the Viewfinder The camera is equipped with diopter adjustment in the range –4 to +2 m–1 to accommodate individual differences in vision. Rotate the diopter adjustment control until the viewfinder display is in sharp focus. Diopter adjustment control 18 Adjusting Display Brightness The brightness of the viewfinder and LCD monitor can be adjusted using the J EVF/LCD BRIGHTNESS option in the setup menu (P 84).
The DISP/BACK Button The DISP/BACK button controls the display of indicators in the viewfinder and LCD monitor. ■ LCD Monitor: Shooting ■ Viewfinder: Shooting 100 F Detailed display Standard display 000100 F 1.0 2000 1.5 2.0 F5.6 3.0 0.1 0.5 5.0 10 200 Standard display P 1.0 2000 1.5 2.0 F5.6 3.0 5.0 10 200 Custom display P 1 2000 5.6 F 200 0.1 0.5 P 100 0.1 0.5 P 1.0 2000 1.5 2.0 F5.6 3.0 1.0 1.5 2000 2.0 3.0 F5.6 F 5.0 10 200 First Steps 0.1 0.5 P 5.
The DISP/BACK Buttion ■ Viewfinder/LCD Monitor: Playback Indicators displayed Indicators hidden Favorites 100-0001 1 / 1000 : : OFF : : -1 2/ 3 3 10 : 00 AM F4.5 -1 2/ 3 100-0001 3:2 F ISO 200 1/1000 3:2 F 12 / 31 / 2050 Photo information 100-0001 12 / 31 / 2050 200 10 : 00 AM Histograms Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the number of pixels by the vertical axis. Shadows Highlights F4.
Basic Photography and Playback Taking Photographs This section describes how to take pictures using program AE (mode P). For information on S, A, and M modes, see page 33. 1 Select program AE. 2 Select single AF. A Rotate the focus mode selector to S (P 42). 3 Ready the camera. 16 11 8 5.6 Hold the camera steady with both hands and brace your elbows against your sides. Shaking or unsteady hands can blur your shots. P 2000 F5.
Taking Photographs 4 Focus. Frame the picture with your subject in the center of the display and press the shutter button halfway to focus. R If the subject is poorly lit, the AF-assist illuminator may light (P 73). If the camera is able to focus, it will beep twice and focus area will glow green. Focus and exposure will lock while the shutter button is pressed halfway. If the camera is unable to focus, the focus frame will turn red, and s will be displayed.
Viewing Pictures Viewing Pictures Full Frame Pictures can be viewed in the viewfinder or LCD monitor. When taking important pictures, take a test shot and check the results. To view pictures full frame, press a. 100-0001 F4.5 -1 2/ 3 200 Additional pictures can be viewed by pressing the selector left or right or rotating the command dial. Press the selector or rotate the dial right to view pictures in the order recorded, left to view pictures in reverse order.
Viewing Pictures Viewing Photo Information The photo information display changes each time the selector is pressed up. 100-0001 3:2 F 12 / 31 / 2050 1 / 1000 10 : 00 AM F4.5 -1 2/ 3 D-RANGE COLOR HIGH LIGHT TONE SHADOW TONE SHARPNESS FILM SIM. WHITE BALANCE : 100 : STD : STD : STD : STD : PROVIA : AUTO 200 Basic data LENS FOCAL LENGTH FLASH MODE : sRGB : PATTERN : PROGRAM : 18mm F2.0 : 18mm : OFF Details, page 2 R Rotate the command dial to view other images.
Viewing Pictures Multi-Frame Playback To change the number of images displayed, press n when a picture is displayed full frame. Press n to view more images. 100-0001 Use the selector to highlight images and press MENU/OK to view the highlighted image full frame. In the nine- and hundred-frame displays, press the selector up or down to view more pictures. Basic Photography and Playback Press k to view fewer images.
Deleting Pictures Follow the steps below to delete the current picture. Note that deleted pictures can not be recovered; copy important pictures to a computer or other storage device before proceeding. R Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P 78). R If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete the pictures. R Pictures can also be deleted from the playback menu (P 76).
Using the Flash Use the built-in flash for additional lighting when shooting at night or indoors under low light. 1 Press the N button to raise the flash. Q The flash may contact accessories mounted on the hot shoe. If necessary, remove accessories before raising the flash. 2 Select p FLASH MODE in the shooting menu.
Using the Flash Q Depending on the distance to the subject, some lenses may cast shadows in photos taken with the flash. R Lower the flash where flash photography is prohibited or to capture natural lighting under dim light. We also recommend that you lower the flash when the camera is off . R If p is displayed when the shutter button is pressed halfway, the flash will fire when the photo is taken. R Except in commander mode, the flash may fire several times with each shot.
Macro Mode (Close-ups) To focus at short distances, press the selector up (MACRO) and select F. To exit macro mode, press the selector up and select OFF.
Basic Movie Recording and Playback Recording High-Definition (HD) Movies The camera can be used to record short high-definition movies. Sound is recorded in stereo via the built-in microphone; do not cover the microphone during recording. 1 Set aperture to A (for more information, see the lens manual). A 16 11 8 5.6 4 2.8 2 Press the DRIVE button to display drive options. Press the selector up or down to highlight F (MOVIE) and press MENU/OK.
Viewing Movies During playback, movies are displayed as shown at right. The following operations can be performed while a movie is displayed: 100-0006 Operation Progress is shown in the display during playback. PLAY Progress bar 15s Q Do not cover the speaker during playback. Q Sound is not played back in silent mode. STOP PAUSE Playback Speed Press the selector left or right to adjust playback speed during playback. Speed is shown by the Arrow number of arrows (M or N).
The Q (Quick Menu) Button Press Q for quick access to the following items. For more information on the options available, see the pages listed below. ISO BASIC 3200 3:2 SET FINE 1 2 3 4 5 6 7 8 u SELECT CUSTOM SETTING ...................... 67 N ISO ........................................................... 41 U DYNAMIC RANGE ................................... 70 D WHITE BALANCE .................................... 39 h NOISE REDUCTION ................................. 71 O IMAGE SIZE ..............
More on Photography and Playback The camera offers a choice of program AE (P), shutter-priority AE (S), aperture-priority AE (A), and manual exposure (M) modes. Program AE (P) To allow the camera to adjust both shutter speed and aperture for optimal exposure, set shutter speed and aperture to A (shutter speed is set by rotating the shutter speed dial; for information on adjusting aperture, see the lens manual). P will appear in the display. A 16 11 8 5.
Choosing an Exposure Mode Shutter-Priority AE (S) To adjust shutter speed manually while letting the camera select aperture for optimal exposure, set aperture to A as described in the lens manual and use the shutter speed dial. S will appear in the display. A 16 11 8 5.6 R Shutter speed can also be adjusted in increments of 1/3 EV by pressing the selector left or right.
Choosing an Exposure Mode A 16 11 8 5.6 4 2.8 Q If the correct exposure can not be achieved at the selected aperture, the shutter speed will be displayed in red when the shutter button is pressed halfway. Adjust aperture until the correct exposure is achieved. Q If the subject is outside the metering range of the camera, the shutter speed display will show “– – –”.
Choosing an Exposure Mode Manual Exposure (M) Exposure can be altered from the value suggested by the camera by setting both shutter speed and aperture to values other than A (shutter speed is set by rotating the shutter speed dial; for information on adjusting aperture, see the lens manual). M will appear in the display. A 16 11 8 5.6 4 2.8 R Shutter speed can also be adjusted in increments of 1/3 EV by pressing the selector left or right. M 2000 F5.6 200 M 2000 F5.
Long Time-Exposures (T/B) R Use of a tripod is recommended to prevent the camera from moving during the exposure. R To reduce “noise” (mottling) in long time-exposures, select ON for K LONG EXPOSURE NR in the shooting menu (P 71). Note that this may increase the time needed to record images after shooting. Time (T) 1 Rotate the shutter speed dial to T. Bulb (B) 1 Rotate the shutter speed dial to B.
Long Time-Exposures (T/B) Using a Remote Release An optional RR-80 remote release can be used for long time-exposures. See the manual provided with the RR-80 for more information. Third-Party Remote Releases Third-party remote releases (available from thirdparty suppliers) can be connected as shown below. Alternatively, electronic remote releases can be connected via the microphone/remote release connector.
White Balance WHITE BALANCE AUTO SET SHIFT WB SHIFT Option Description Option Description AUTO White balance adjusted automatically. j For subjects in the shade. h Measure a value for white balance (P 40). k Use under “daylight” fluorescent lights. Selecting this option displays a list of color l Use under “warm white” fluorescent lights. temperatures (P 40); highlight a temperam Use under “cool white” fluorescent lights. k ture and press MENU/OK to select the highn Use under incandescent lighting.
White Balance h: Custom White Balance Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will be displayed; frame a white object so that it fills the display and press the shutter button all the way down to measure white balance (to select the most recent custom value and exit without measuring white balance, press DISP/BACK, or press MENU/OK to select the most recent value and display the fine-tuning dialog).
Sensitivity P SHOOTING MENU 1 Press MENU/OK in shooting mode to display the shooting menu. Press ISO IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION FILM SIMULATION BKT SELF-TIMER the selector up or down to highlight N ISO and press MENU/OK. R At default settings, ISO options can also be displayed by pressing the Fn button. 2 Press the selector up or down to highlight the desired option and O MENU P SHOOTING ISO F OFF P 2000 F5.6 OFF EXIT 3:2 press MENU/OK to select.
Focus Mode Use the focus mode selector to choose how the camera focuses (note that regardless of the option selected, manual focus will be used when the lens is in manual focus mode). • S (single AF): Focus locks while the shutter button is pressed halfway. Choose for stationary subjects. • C (continuous AF): Focus is continually adjusted to reflect changes in the distance to the subject even when the shutter button is not pressed halfway (note that this increases the drain on the battery).
Focus Mode 0.1 0.5 M 1.0 2000 1.5 2.0 F5.6 3.0 5.0 10 200 0.1 0.5 M 1.0 2000 1.5 2.0 F5.6 3.0 5.0 10 200 More on Photography and Playback Manual Focus: Checking Focus Pressing the center of the command dial magnifies the view in the viewfinder or LCD monitor for precise focus; rotate the dial to zoom in or out. To scroll to other areas of the frame, press the AF button and use the selector.
Focus Mode Focus Frame Selection When t AREA is selected for F AF MODE in the shooting menu and S is selected for focus mode, the camera offers a choice of focus points, allowing photographs to be composed with the main subject positioned almost anywhere in the frame. To position the focus frame, press the AF button and use the selector (the focus frame can be returned to the center by pressing MENU/OK). Press the AF button again to put the setting into effect.
Focus/Exposure Lock 1 Focus: Position the subject in the focus frame and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while the shutter button is pressed halfway (AF/AE lock). P 2000 F5.6 200 R Depending on the option selected for v AE/AF-LOCK BUTTON in the shooting menu (P 73), focus and/ or exposure can also be locked by pressing the AE-L/AF-L button; focus and/or exposure will remain locked even when the shutter button is pressed halfway.
Focus/Exposure Lock Autofocus Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed below. • Very shiny subjects such as mirrors or car bodies. • Fast-moving subjects. • • • • Subjects photographed through a window or other reflective object. Dark subjects and subjects that absorb rather than reflect light, such as hair or fur. Insubstantial subjects, such as smoke or flame.
Exposure Compensation Exposure compensation indicator 000100 F P 2000 F5.6 200 Standard display Choose positive values (+) to increase exposure P 1 2000 5.6 F 200 Detailed display (LCD monitor) Exposure Value (EV) The exposure value is determined by the sensitivity of the image sensor and the amount of light to which the sensor is exposed. Doubling the amount increases EV by one, while halving it reduces EV by one.
Metering To choose how the camera meters exposure, press the AE button to display metering options. Use the selector to highlight an option and press AE to select. Mode Description The camera instantly determines exposure based on an analysis of o composition, color, and brightness distribution. Recommended in (MULTI) most situations. The camera meters lighting conditions in an area at the center of the frame equivalent to 2% of the total.
Using the Self-Timer P SHOOTING MENU 1 Press MENU/OK in shooting mode to display the shooting menu. Press ISO IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION FILM SIMULATION BKT SELF-TIMER the selector up or down to highlight B SELF-TIMER and press MENU/ OK. EXIT 2 Press the selector up or down to highlight one of the following options and press MENU/OK to select. Option Description The shutter is released two seconds after the shutter button is pressed.
Using the Self-Timer 4 Press the shutter button the rest of the way down to start the timer. The display in the monitor shows the number of seconds remaining until the shutter is released. To stop the timer before the picture is taken, press DISP/BACK. The self-timer lamp on the front of the camera will blink immediately before the picture is taken. If the two-second timer is selected, the self-timer lamp will blink as the timer counts down.
Film Simulation 1 Press MENU/OK in shooting mode to display the shooting menu. Press P SHOOTING MENU ISO IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION FILM SIMULATION BKT SELF-TIMER the selector up or down to highlight P FILM SIMULATION and press MENU/OK. 200 3:2 F OFF EXIT 2 Press the selector up or down to highlight one of the following options and press MENU/OK to select. Option c (PROVIA/STANDARD) > (Velvia/VIVID) Description Standard color reproduction.
Bracketing Automatically vary settings over a series of pictures. 1 Press the DRIVE button to display drive options and press the selector up or down to highlight one of the following: Option Description Press the selector left or right to highlight a bracketing amount.
Multiple Exposures 1 Select ON for n MULTIPLE EXPOSURE in the 4 Take the second shot. shooting menu. 2 Take the first shot. 5 Press MENU/OK to create the multiple 3 Press MENU/OK. You will be prompted to take the second shot. R To return to Step 2 and retake the first shot, press the selector left. To save the first shot and exit without creating a multiple exposure, press DISP/ BACK. exposure, or press the selector left to return to Step 4 and retake the second shot.
Continuous Shooting (Burst Mode) Capture motion in a series of pictures. 1 Press the DRIVE button to display drive options. 6fps 3fps CONTINUOUS 2 Press the selector up or down to choose from frame rates of approximately 6 fps (frames per second) and 3 fps, and press left or right to choose the number of shots per burst. Press MENU/OK to proceed when settings are complete. 3 Press the shutter button halfway to focus. 54 4 Press the shutter button the rest of the way down to start shooting.
Continuous Shooting (Burst Mode) Position in burst/total number of pictures in burst PLAY CONTINUOUS SHOTS PLAY NORMAL 1/ 10 First picture in burst R Pressing the selector right when the last picture in the burst is displayed displays the first picture in the burst; similarly, pressing the selector left when the first picture is displayed displays the last picture. R Deletion (P 76), rotation (P 78), and protect (P 78) operations applied during burst mode playback apply only to the current picture.
Panoramas Follow an on-screen guide to create a panorama. 1 Press the DRIVE button to display 5 Pan the camera in the direction shown by the drive options. Press the selector up or down to highlight r (MOTION PANORAMA) and press MENU/OK. arrow. Shooting ends automatically when the camera is panned to the end of the guides and the panorama is complete. MOTION PANORAMA ANGLE 2 To select the size of the angle through which you will pan the camera while shooting, press the selector left.
Panoramas For Best Results For best results, use a lens with a focal length of 35 mm or less (50 mm or less in 35 mm format). Prop your elbows against your sides and move the camera slowly in a small circle at a steady speed, keeping the camera parallel or at right angles to the horizon and being careful only to pan in the direction shown by the guides. Use a tripod for best results. If the desired results are not achieved, try panning at a different speed.
Panoramas Viewing Panoramas In full-frame playback, panoramas can be played back using the selector. Press the selector down to start playback and press again to pause. While playback is paused, you can scroll the panorama manually be pressing the selector left or right. To exit to full-frame playback, press the selector up.
Recording Pictures in RAW Format R RAW images record raw, unprocessed data from the camera image sensor. JPEG copies of RAW images can be created using the j RAW CONVERSION option in the playback menu, or RAW images can be viewed on a computer using the RAW FILE CONVERTER application that is installed with the software on the supplied CD (P 88, 89). R Sensitivities of L (100), H (12800), and H (25600) are not available when RAW image quality is on (P 41).
Recording Pictures in RAW Format Creating JPEG Copies of RAW Pictures RAW pictures store information on camera settings separately from the data captured by the camera image sensor. Using the j RAW CONVERSION option in the playback menu, you can create JPEG copies of RAW pictures using different options for the settings listed below. The original image data are unaffected, allowing a single RAW image to be processed in a multitude of different ways.
Using a Mount Adapter R Attaching a mount adapter enables m SHOOT WITHOUT LENS (P 72) and hides the distance indicator in the standard display. R Before checking focus, set the focus mode selector to M (P 42). Mount Adapter Settings Pressing the function button on the mount adapter displays l MOUNT ADAPTOR SETTING options.
Using a Mount Adapter ■ Color Shading Correction Color (shading) variations between the center and edges of the frame can be adjusted separately for each corner. NEXT SET To use color shading correction, follow the steps below. 1 Rotate the command dial to choose a corner. The selected corner is indicated by a triangle. 2 Use the selector to adjust shading until there is no visible difference in color between the selected corner and the center of the image.
Image Search 1 Press MENU/OK during playback to display the playback menu. Press the selector up or down to highlight b IMAGE SEARCH and press MENU/OK. 2 Highlight an option and press MENU/OK. Option BY DATE BY FACE BY I FAVORITES BY TYPE OF DATA BY UPLOAD MARK Description Search by date. Search for pictures that include faces. Search by rating (P 23). Find all still pictures, all movies, all pictures taken in burst mode, or all RAW pictures.
PhotoBook Assist Create books from your favorite photos. Creating a PhotoBook 1 Select NEW BOOK for m PHOTOBOOK ASSIST in the playback menu (P 80) and choose from the following options: • SELECT FROM ALL: Choose from all available pictures. • SELECT BY IMAGE SEARCH: Choose from pictures matching selected search conditions (P 63). R Neither photographs a or smaller nor movies can be selected for photobooks. 2 Scroll through the images and press the selector up to select or deselect.
PhotoBook Assist Editing and Deleting Photobooks Display the photobook and press MENU/OK. The following options will be displayed; select the desired option and follow the on-screen instructions. • EDIT: Edit the book as described in “Creating a PhotoBook” (P 64). • ERASE: Delete the book. More on Photography and Playback Viewing Photobooks Highlight a book in the photobook assist menu and press MENU/OK to display the book, then press the selector left or right to scroll through the pictures.
The Fn Button The role played by the Fn button can be selected using the F Fn BUTTON option in the shooting menu (P 71). The options available include multiple exposure (P 53), depth-of-field preview (P 35), sensitivity (P 41), the self-timer (P 49), image size (P 69), image quality (P 69), dynamic range (P 70), film simulation (P 51), white balance (P 39), AF mode (P 72), custom settings (P 67), movie recording (P 30), and RAW/JPEG toggle (P 59).
Saving Settings P SHOOTING MENU 1 Press MENU/OK in shooting mode to display the shooting menu. Press SELECT CUSTOM SETTING EDIT/SAVE CUSTOM SETTING Fn BUTTON DISP. CUSTOM SETTING FRAMING GUIDLINE MOUNT ADAPTOR SETTING SHOOT WITHOUT LENS the selector up or down to highlight K EDIT/SAVE CUSTOM SETTING and press MENU/OK. 35mm OFF EXIT 2 Highlight a custom settings bank and press MENU/OK to select.
Advanced Movie Recording Depth of Field Aperture can be set manually for movie recording by selecting an aperture other than A for aperture-priority AE. Adjust aperture before recording begins. Choose low f-numbers to soften background details. The effect can be heightened by increasing the distance between your subject and the background. A 16 11 8 5.6 4 2.8 Q Movies recorded when the aperture is displayed in red will not be correctly exposed.
Menus Using the Menus: Shooting Mode The shooting menu is used to adjust settings for a wide range of shooting conditions. To display the shooting menu, press MENU/OK in shooting mode. Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete.
Using the Menus: Shooting Mode U DYNAMIC RANGE (default: V) Control contrast. Choose lower values to increase contrast when shooting indoors or under overcast skies, higher values to reduce loss of detail in highlights and shadows when photographing high-contrast scenes.
Using the Menus: Shooting Mode h NOISE REDUCTION Reduce noise in pictures taken at high sensitivities. (default: STANDARD) K LONG EXPOSURE NR Select ON to reduce mottling in long time-exposures (P 37). (default: ON) u SELECT CUSTOM SETTING Recall settings saved with K EDIT/SAVE CUSTOM SETTING. K EDIT/SAVE CUSTOM SETTING Save settings (P 67). F Fn BUTTON Choose the role played by the Fn button (P 66). (default: N ISO) Menus v DISP.
Using the Menus: Shooting Mode c FRAMING GUIDLINE Choose the type of framing grid available in shooting mode. F GRID 9 P For “rule of thirds” composition. (default: F GRID 9) G GRID 24 H HD FRAMING A six-by-four grid. Frame HD pictures in the crop shown by the lines at the top and bottom of the display. P P l MOUNT ADAPTOR SETTING Adjust settings for M-mount lenses connected using an optional FUJIFILM M MOUNT ADAPTER (P 61).
Using the Menus: Shooting Mode C AF ILLUMINATOR If ON is selected, the AF-assist illuminator will light to assist autofocus. (default: ON) R The AF-assist illuminator turns off automatically in silent mode. Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro mode, try increasing the distance to the subject. Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
Using the Menus: Shooting Mode p FLASH MODE Choose a flash mode for optional flash units (P 27). (default: ±0) I FLASH Adjust flash brightness. Choose from values between +2/3 EV and –2/3 EV. Note that the desired results may not be achieved depending on shooting conditions and the distance to the subject. B RED EYE REMOVAL Choose ON to remove red-eye effects caused by the flash. (default: OFF) R Red-eye reduction is performed only when a face is detected.
Using the Menus: Shooting Mode Shooting Menu Options (Movie Mode) The following options are available in movie mode (P 30). W MOVIE MODE Select a frame size for movie recording. • i 1920×1080: Full HD • h 1280×720: HD P FILM SIMULATION Simulate the effects of different types of film (P 51). D WHITE BALANCE Adjust colors to match the light source (P 39). t MIC LEVEL ADJUSTMENT Adjust the microphone recording level.
Using the Menus: Playback Mode PLAYBACK MENU To display the playback menu, press MENU/OK in playback mode. Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete. RAW CONVERSION ERASE CROP RESIZE PROTECT IMAGE ROTATE RED EYE REMOVAL EXIT Playback Menu Options j RAW CONVERSION Create JPEG copies of RAW pictures (P 60). A ERASE Delete all or selected pictures.
Using the Menus: Playback Mode G CROP Create a cropped copy of the current picture. 1 Display the desired picture. 2 Select G CROP in the playback menu. 3 Use the k and n buttons to zoom in and out and press the selector up, down, left, or right to scroll the picture until the desired portion is displayed. 4 Press MENU/OK to display a confirmation dialog. 5 Press MENU/OK again to save the cropped copy to a separate file. R Larger crops produce larger copies; all copies have an aspect ratio of 3 : 2.
Using the Menus: Playback Mode D PROTECT Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK. • FRAME: Protect selected pictures. Press the selector left or right to view pictures and press MENU/OK to select or deselect. Press DISP/BACK when the operation is complete. • SET ALL: Protect all pictures. • RESET ALL: Remove protection from all pictures. Q Protected pictures will be deleted when the memory card is formatted (P 86). C IMAGE ROTATE Rotate pictures.
Using the Menus: Playback Mode B RED EYE REMOVAL Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create a copy with reduced red-eye. 1 Display the desired picture. 2 Select B RED EYE REMOVAL in the playback menu. 3 Press MENU/OK. R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on the scene.
Using the Menus: Playback Mode m PHOTOBOOK ASSIST Create books from your favorite photos (P 64). j MARK FOR UPLOAD TO Select pictures for upload to YouTube or Facebook using MyFinePix Studio (Windows only). 1 Highlight an option and press MENU/OK. Select YouTube to choose movies for upload to YouTube, FACEBOOK to choose photos and movies for upload to Facebook. 2 Press the selector left or right to display pictures and press MENU/OK to select or deselect.
Using the Menus: Playback Mode K PRINT ORDER (DPOF) Select pictures for printing on DPOF- and PictBridge-compatible devices (P 95). J DISP ASPECT Choose how High Definition (HD) devices display pictures with an aspect ratio of 3 : 2 (this option is available only when an HDMI cable is connected). Select 16 : 9 to display the image so that it fills the screen with its top and bottom cropped out, 3 : 2 to display the entire image with black bands at either side.
The Setup Menu Using the Setup Menu 1 Display the setup menu. 1.1 Press MENU/OK to display the menu for the current mode. 1.2 Press the selector left to highlight the tab for the current menu. 1.3 Press the selector down to highlight Z. SET-UP DATE/TIME TIME DIFFERENCE ENGLISH RESET SILENT MODE FRAME NO. FOCUS RING OFF CONT. EXIT Tab 1.4 Press the selector right to place the cursor in the setup menu. 2 Adjust settings.
The Setup Menu Setup Menu Options F DATE/TIME Set the camera clock (P 16). N TIME DIFFERENCE (default: h) Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between local time and your home time zone: 1 Highlight g LOCAL and press MENU/OK. 2 Use the selector to choose the time difference between local time and your home time zone. Press MENU/OK when settings are complete.
The Setup Menu (default: CONTINUOUS) B FRAME NO. New pictures are stored in image files named using a four-digit file number assigned by adding one to the Frame number last file number used. The file number is displayed during playback as shown at right. B FRAME NO. con100-0001 trols whether file numbering is reset to 0001 when a new memory card is inserted or the current memory card is formatted.
The Setup Menu (default: 2 MIN) M AUTO POWER OFF Choose the length of time before the camera turns off automatically when no operations are performed. Shorter times reduce the drain on the battery; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera turns off automatically even when OFF is selected. G OPERATION VOL. (default: c) Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF (mute) to disable control sounds.
The Setup Menu J COLOR SPACE Choose the gamut of colors available for color reproduction. Option sRGB Adobe RGB (default: sRGB) Description Recommended in most situations. For commercial printing. c GUIDANCE DISPLAY Choose whether tool tips are displayed when adjustments are made to such settings as silent and macro modes. M FOCUS SCALE UNITS Choose the units used for the focus distance indicator (P 42). (default: ON) (default: METERS) O BACKGROUND COLOR Choose a color scheme.
Connections Viewing Pictures on a Computer The supplied software can be used to copy pictures to a computer, where they can be stored, viewed, organized, and printed. Before proceeding, install the software as described below. Do NOT connect the camera to the computer until installation is complete.
Viewing Pictures on a Computer 3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive. Windows 7/Windows Vista If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed; click Yes (Windows 7) or Allow (Windows Vista). The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio and RAW FILE CONVERTER.
Viewing Pictures on a Computer Macintosh: Installing FinePixViewer 1 Confirm that the computer meets the following system requirements: PowerPC or Intel (Core 2 Duo or better) * Pre-installed copies of Mac OS X version 10.5–10.6 (visit http://www.fujifilm.com/support/digital_cameras/ OS compatibility/ for more information). Mac OS X version 10.7 and later not supported.
Viewing Pictures on a Computer 5 Mac OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences… from the Image Capture application menu. The Image Capture preferences dialog will be displayed; choose Other… in the When a camera is connected, open menu, then select FPVBridge in the “Applications/FinePixViewer” folder and click Open. Quit Image Capture. Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image Capture.
Viewing Pictures on a Computer Connecting the Camera 1 Find a memory card containing pictures you want to copy to the computer and insert the card into the camera (P 11). R Windows users may require the Windows CD when starting the software for the first time. Q Loss of power during transfer could result in loss of data or damage to the memory card. Insert a fresh or fully-charged battery before connecting the camera.
Viewing Pictures on a Computer Q If a memory card containing a large number of images is inserted, there may be a delay before the software starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Printing Pictures via USB If the printer supports PictBridge, the camera can be connected directly to the printer and pictures can be printed without first being copied to a computer. Note that depending on the printer, not all the functions described below may be supported. Connecting the Camera 1 Connect the supplied USB cable as shown and turn the printer on. Printing Selected Pictures 1 Press the selector left or right to display a picture you wish to print.
Printing Pictures via USB Printing the Date of Recording To print the date of recording on pictures, press DISP/BACK in the PictBridge display and select PRINT WITH DATE s (to print pictures without the date of recording, select PRINT WITHOUT DATE). To ensure that the date is correct, set the camera clock before taking pictures. Some printers do not support date printing. See the printer manual for details.
Printing Pictures via USB During Printing The message shown at right is displayed during printing. Press DISP/BACK to cancel before all pictures are printed (depending on the printer, printing may end before the current picture has printed). PRINTING CANCEL If printing is interrupted, turn the camera off and then on again. DPOF DPOF (Digital Print Order Format) is standard that allows pictures to be printed from “print orders” stored on the memory card.
Printing Pictures via USB ■ WITH DATE s/ WITHOUT DATE To modify the DPOF print order, select K PRINT ORDER (DPOF) in the playback menu and press the selector up or down to highlight WITH DATE s or WITHOUT DATE. Y PLAYBACK MENU WITH DATE s: Print date of recording on pictures. SLIDE SHOW PHOTOBOOK ASSIST WITH DATE s MARK FOR UPLOAD TO WITHOUT DATE IMAGE SEARCH RESET ALL PRINT ORDER (DPOF) DISP ASPECT PLAYBACK VOLUME WITHOUT DATE: Print pictures without date. Press MENU/OK and follow the steps below.
Printing Pictures via USB ■ RESET ALL To cancel the current print order, select RESET ALL for K PRINT ORDER (DPOF). The confirmation shown at right will be displayed; press MENU/OK to remove all pictures from the order. RESET DPOF OK? YES CANCEL R Print orders can contain a maximum of 999 pictures. RESET DPOF OK? R If a memory card is inserted containing a print order created by another camera, the message shown at right will YES NO be displayed.
Viewing Pictures on TV To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately from third-party suppliers; note that the TV can only be used for playback, not shooting). 1 Turn the camera off. 2 Connect the cable as shown below. Insert into HDMI connector Insert into HDMI mini connector R Be sure the connectors are fully inserted. 3 Tune the television to the HDMI input channel. See the documentation supplied with the television for details.
Technical Notes Optional Accessories The camera supports a wide range of accessories from FUJIFILM and other manufacturers. Accessories from FUJIFILM The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/ products/digital_cameras/index.html.
Optional Accessories FUJINON Lenses XF18mmF2 R: F=18 mm, maximum aperture f/2. XF35mmF1.4 R: F=35 mm, maximum aperture f/1.4. XF60mmF2.4 R Macro: F=60 mm, maximum aperture f/2.4. Mount Adapters FUJIFILM M MOUNT ADAPTER: Allows the camera to be used with a wide selection of M-mount lenses. Protector Filters PRF-52: Protector filter (diameter 52 mm). PRF-39: Protector filter (diameter 39 mm). Grips HG-XE1: Features an improved grip.
Optional Accessories Shoe-mounted flash units EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide Number of 20/65 (ISO 100, m/ft.) and supports TTL flash control. The flash head can be rotated upwards 90° for bounce lighting. EF-42: This clip-on flash unit (powered by four AA batteries) has a Guide Number of 42/137 (ISO 100, m/ft.) and supports TTL flash control and auto power zoom in the range 24–105 mm (35 mm format equivalent).
Optional Accessories Connecting the Camera to Other Devices ■ Remote Shutter Release ■ External Microphones External microphone † RR-80 remote release * ■ Flash Photography Remote release † ■ Printing X-E1 EF-20 shoe mount EF-42 shoe mount flash * flash * USB cable (supplied) EF-X20 shoe mount flash * ■ Lens PictBridge-compatible printer † SD/SDHC/SDXC memory card † XF18mmF2 R * Printer XF35mmF1.4 R * XF60mmF2.
Caring for the Camera To ensure continued enjoyment of the product, observe the following precautions. ■ Water and Sand Exposure to water and sand can also damage the camera and its internal circuitry and mechanisms. When using the camera at the beach or seaside, avoid exposing the camera to water or sand. Do not place the camera on a wet surface. ■ Condensation Sudden increases in temperature, such as occur when entering a heated building on a cold day, can cause condensation inside the camera.
Cleaning the Image Sensor Multiple photographs marred by spots or blotches in identical locations may indicate the presence of dust on the camera image sensor. Clean the sensor using the V SENSOR CLEANING option in the setup menu (P 85); if the problem persists, you can clean the sensor manually as described below. Note that there will be a charge to repair or replace the image sensor if it is damaged during cleaning. 1 Use a blower (not a brush) to remove dust from the sensor.
Troubleshooting Problems and Solutions ■ Power and Battery Problem The camera does not turn on. The monitor does not turn on. The battery runs down quickly. The battery is exhausted exhausted:: Charge the battery ((P P 10) or insert a fully-charged spare battery ((P P 11). Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P P 10). Charge the battery at room temperature ((P P iv).
Problems and Solutions ■ Shooting Problem No picture is taken when the shutter button is pressed. • • • • • • • Solution The memory card is full full:: Insert a new memory card or delete pictures (P (P 11, 26). The memory card is not formatted formatted:: Format the memory card (P (P 86). There is dirt on the memory card contacts contacts:: Clean the contacts with a soft, dry cloth. The memory card is damaged damaged:: Insert a new memory card ((P P 11).
Problems and Solutions Problem The flash does not fully light the subject. Pictures are blurred. Pictures are mottled. • • • • • • • • • Solution The subject is not in range of the flash ash:: Position the subject in range of the flash ((P P 115). The flash window is obstructed obstructed:: Hold the camera correctly ((P P 21). Shutter speed is faster than 1/180 ss:: Choose a slower shutter speed ((P P 28, 34, 36). The lens is dirty dirty:: Clean the lens ((P P ix).
Problems and Solutions ■ Connections/Miscellaneous Problem No picture or sound. The computer does not recognize the camera. Can not transfer RAW or JPEG files to computer. Pictures can not be printed. Only one copy is printed/ the date is not printed. The camera is unresponsive. The camera does not function as expected. No sound. 108 Solution • The camera is not properly connected: connected: Connect the camera properly (P (P 98).).
Warning Messages and Displays The following warnings appear in the display. Warning B (red) A (blinks red) k s (displayed in red with red focus frame) Aperture or shutter speed displayed in red FOCUS ERROR TURN OFF THE CAMERA AND TURN ON AGAIN LENS CONTROL ERROR LENS ERROR BUSY PROTECTED CARD Camera malfunction. Turn the camera off and then on again. If the message persists, contact a FUJIFILM dealer.
Warning Messages and Display Warning CARD ERROR b MEMORY FULL NO CARD WRITE ERROR READ ERROR FRAME NO. FULL Description • The memory card is not formatted for use in the camera camera:: Format the card (P (P 86). • The memory card contacts require cleaning or the memory card is damaged damaged:: Clean the contacts with a soft, dry cloth. If the message is repeated, format the card (P (P 86). If the message persists, replace the card. • Incompatible memory card: card: Use a compatible card ((P P 14).
Warning Messages and Display Warning PROTECTED FRAME CAN NOT CROP m CANNOT EXECUTE F CANNOT EXECUTE CAN NOT ROTATE F CAN NOT ROTATE Troubleshooting Description An attempt was made to delete or rotate to a protected picture. Remove protection and try again ((P P 78). The picture is damaged or was not created with the camera. Red-eye removal can not be applied to pictures created with other devices. Red-eye removal can not be applied to movies. The selected picture can not be rotated.
Appendix Glossary Exif Print: A standard for storing information with pictures for optimal color reproduction during printing. HDMI (High-Definition Multimedia Interface): An interface standard for the transmission of images and sound that adds audio input to the DVI interface used to connect computers to displays. JPEG (Joint Photographic Experts Group): A compressed file format for color images.
Memory Card Capacity The following table shows the recording time or number of pictures available at different image sizes. All figures are approximate; file size varies with the scene recorded, producing wide variations in the number of files that can be stored. The number of exposures or length remaining may not diminish at an even rate.
Specifications System Model Effective pixels Image sensor Storage media File system File format Image size Lens mount Sensitivity Metering Exposure control Exposure compensation Shutter speed (mechanical shutter) 114 FUJIFILM X-E1 digital camera 16.3 million 23.6 mm × 15.
Specifications System Continuous Focus White balance Self-timer Flash Mode Hot shoe Viewfinder LCD monitor Movies Approximately 6 or 3 fps • Mode Mode:: Single or continuous AF; manual focus with focus ring • Focus-area selection selection:: Multi, area with focus area size selection; 49 (7 × 7) areas available in viewfinder and LCD monitor • Autofocus system: system: Contrast-detect TTL AF with AF-assist illuminator Custom, color temperature selection, auto, direct sunlight, shade, daylight fluorescent, w
Specifications Power supply/other Power supply NP-W126 rechargeable battery Battery life (approximate Battery type Approximate number of frames number of frames that can NP-W126 (type supplied with camera) 350 be taken with a fully-charged battery and XF 35 mm f/1.4 CIPA standard, measured using battery supplied with camera and SD memory card. R lens) Note:: Number of shots that can be taken with battery varies with battery charge level and will decline at low Note temperatures. Camera size (W × H × D) 129.
Specifications NP-W126 rechargeable battery Nominal voltage 7.2 V DC Nominal capacity 1,260 mAh Operating temperature 0 °C to +40 °C/+32 °F to +104 °F Dimensions (W × H × D) 36.4 mm × 47.1 mm × 15.7 mm/1.4 in. × 1.8 in. × 0.6 in. Weight Approx. 47 g/1.7 oz. BC-W126 battery charger Rated input Input capacity Rated output Supported batteries Charging time Operating temperature Dimensions (W × H × D) Weight 100 V – 240 V AC, 50/60 Hz 13 –21 VA 8.4 V DC, 0.6 A NP-W126 rechargeable batteries Approx.
Specifications ■ Notices • Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/ digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual. • Although the viewfinder and LCD monitor are manufactured using advanced high-precision technology, small bright points and anomalous colors may appear, particularly in the vicinity of text.
Restrictions on Camera Settings The options available in each shooting mode are listed below.
Restrictions on Camera Settings Option T IMAGE QUALITY U DYNAMIC RANGE P FILM SIMULATION FINE NORMAL FINE+RAW NORMAL+RAW RAW AUTO V W X c d e g h b e d f f B SELF-TIMER D WHITE BALANCE f COLOR q SHARPNESS r HIGHLIGHT TONE s SHADOW TONE h NOISE REDUCTION K LONG EXPOSURE NR 120 P ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ S ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ A ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ M ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ nr ✔
Restrictions on Camera Settings Option F AF MODE s t C AF ILLUMINATOR L IS MODE p FLASH MODE B OFF B ON AUTO N O l C K L M d C S ✔ ✔ ✔ ✔ A ✔ ✔ ✔ ✔ M ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ n ✔ ✔ ✔ ✔ ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔ rF ✔5 ✔5 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔6 1 2 3 4 5 6 7 Fixed at OFF OFF.. Fixed at o (multi). Continuous AF is used when S is selected for focus mode. Fixed at Q. Center focus area selected automatically.
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN http://www.fujifilm.com/products/digital_cameras/index.