BL02401-101 DIGITAL CAMERA X100S Owner’s Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM X100S digital camera and install the supplied software. Be sure that you have read and understood its contents before using the camera.
For Your Safety IMPORTANT SAFETY INSTRUCTIONS • Read Instructions: All the safety and operating instructions should be read before the appliance is operated. • Retain Instructions: The safety and operating instructions should be retained for future reference. • Heed Warnings: All warnings on the appliance and in the operating instructions should be adhered to. • Follow Instructions: All operating and use instructions should be followed.
For Your Safety Service Be sure to read these notes before use Servicing: Do not attempt to service this video product Safety Notes yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to • Make sure that you use your camera correctly. Read these qualified service personnel. safety notes and your Owner’s Manual carefully before use.
For Your Safety WARNING Use only batteries or AC power adapters specified for use with this camera. Do not use voltages other than the power supply voltage shown. The use of other power sources can cause a fire. If the battery leaks and fluid gets in contact with your eyes, skin or clothing, flush the affected area with clean water and seek medical attention or call an emergency number right away. Do not use the charger to charge batteries other than those specified here.
For Your Safety ■ Battery Life At normal temperatures, the battery can be recharged about 300 times. A noticeable decrease in the length of time the battery will hold a charge indicates that it has reached the end of its service life and should be replaced. ■ Storage Performance may be impaired if the battery is left unused for extended periods when fully charged. Run the battery flat before storing it.
For Your Safety Using the Camera • Do not aim the camera at extremely bright light sources, such as the sun in a cloudless sky. Failure to observe this precaution could damage the camera image sensor. • Strong sunlight focused through the viewfinder may damage the panel of electronic viewfinder (EVF). Do not aim the electronic viewfinder at the sun. Liquid Crystal In the event that the display is damaged, care should be taken to avoid contact with liquid crystal.
For Your Safety NOTICES To prevent fire or shock hazard, do not expose the unit to rain or moisture. For Customers in Canada CAUTION: This Class B digital apparatus complies with Canadian ICES-003. Please read the “Safety Notes” and make sure you understand them before using the Disposal of Electrical and Electronic Equipment in Private Households In the European Union, Norway, Iceland and Liechtenstein: This symbol on the camera.
About This Manual Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information on specific topics, consult the sources below. Table of Contents ................................................... P x The “Table of Contents” gives an overview of the entire manual. The principal camera operations are listed here. Troubleshooting ................................................P ................................................
Caring for the Camera For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body. Any liquid on the camera should be removed immediately with a soft, dry cloth. Use a blower to remove dust from the lens and monitor, then gently wipe with a soft, dry cloth.
Table of Contents For Your Safety .....................................................................................ii IMPORTANT SAFETY INSTRUCTIONS.........................................ii Safety Notes .......................................................................................iii NOTICES ..............................................................................................vii About This Manual ..........................................................................
Table of Contents The Q (Quick Menu) Button Using the Q (Quick Menu) Button ............................................ 34 More on Photography and Playback Choosing an Exposure Mode ..................................................... 36 Program AE (P) ................................................................................ 36 Shutter-Priority AE (S) .................................................................. 37 Aperture-Priority AE (A).....................................................
Table of Contents Menus Using the Menus: Shooting Mode ........................................... 72 Shooting Menu Options (Photographs) ............................... 72 B SELF-TIMER ............................................................................. 72 N ISO.............................................................................................. 72 O IMAGE SIZE ............................................................................. 72 T IMAGE QUALITY ...............................
Table of Contents The Setup Menu ............................................................................... 87 Using the Setup Menu ................................................................. 87 Setup Menu Options .................................................................... 88 F DATE/TIME .............................................................................. 88 N TIME DIFFERENCE................................................................. 88 L a................................
Table of Contents xiv Technical Notes Troubleshooting Optional Accessories....................................................................105 Accessories from FUJIFILM .......................................................105 Attaching Adapter Rings...........................................................107 Attaching Lens Hoods................................................................107 Attaching Protector Filters .......................................................
Before You Begin Symbols and Conventions Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may be simplified for explanatory purposes. Supplied Accessories Before You Begin The following symbols are used in this manual: Q This information should be read before use to ensure correct operation. R Additional information that may be helpful when using the camera. POther pages in this manual on which related information may be found.
Parts of the Camera For more information, refer to the page listed to the right of each item. 1 2 3 4 5 6 7 8 9 10 11 12 2 Shutter button .............................................. 111 Exposure compensation dial ........................... 51 Shutter speed dial ..........................36, 37, 38, 39 Hot shoe...................................................30, 109 Flash ............................................................... 29 Microphone (L)................................................
Parts of the Camera 37 VIEW MODE button........................................ 18 41 Command dial................................................... 4 38 AFL/AEL (focus lock/exposure) button 42 Q (quick menu) button...............................19, 34 .............................................................46, 49, 78 43 DISP (display)/BACK button........................... 21 39 Indicator lamp (see below) o (silent mode) button .................................. 5 40 MENU/OK button .................
Parts of the Camera The Command Dial Rotate the command dial or press it up (q), right (w), down (e), or left (r) to highlight items and press MENU/OK (t) to select.
Parts of the Camera Silent Mode In situations in which camera sounds or lights may be unwelcome, press the DISP/BACK button until the o icon is displayed (about a second), or select ON for o SILENT MODE in the setup menu (P 88). The camera speaker, flash, and AF-assist illuminator/selftimer lamp turn off and flash and volume settings can not be adjusted (note that silent mode can not be enabled or disabled while movie playback is in progress). Press the DISP/BACK button again to resume normal operation.
Parts of the Camera Camera Displays The following types of indicator may be displayed during shooting and playback. In the description that follows, all available indicators are shown for illustrative purposes; the indicators actually displayed vary with camera settings. ■ Shooting: Optical Viewfinder 100 100 P 2000 F5.6 200 * a: indicates that no memory card is inserted and that pictures will be stored in the camera’s internal memory (P 13). 6 1 2 3 4 5 6 7 8 9 10 11 12 Manual focus indicator ....
Parts of the Camera ■ Shooting: Electronic Viewfinder 100 1.0 2000 1.5 2.0 3.0 5.0 10 F5.6 200 * a: indicates that no memory card is inserted and that pictures will be stored in the camera’s internal memory (P 13). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Flash mode ..................................................... 29 Macro (close-up) mode ................................... 31 Self-timer indicator ......................................... 53 Continuous mode ...................................
Parts of the Camera ■ Shooting: LCD Monitor 000100 F P 1 2000 5.6 F 200 * a: indicates that no memory card is inserted and that pictures will be stored in the camera’s internal memory (P 13). 1 2 3 4 5 6 7 8 9 10 11 12 13 Flash mode ..................................................... 46 Macro (close-up) mode ................................... 31 Metering ......................................................... 52 Continuous mode ............................................
First Steps Attaching the Strap Attach the strap clips to the camera and then attach the strap. 1 Open a strap clip. 3 Pass the clip through the eyelet. Rotate the clip fully through the eyelet until it clicks closed. 4 Attach a protective cover. Q Keep the tool in a safe place. You will need it to open the strap clips when removing the strap. First Steps Use the clip attaching tool to open a strap clip, making sure that the tool and clip are in the orientations shown.
Attaching the Strap 5 Insert the strap. Insert the strap through a protective cover and strap clip. 6 Fasten the strap. Fasten the strap as shown. Repeat Steps 5–6 for the second eyelet. Q To avoid dropping the camera, be sure the strap is correctly secured.
Charging the Battery The battery is not charged at shipment. Charge the battery before use. 1 Place the battery in the charger. 2 Plug the charger in. Insert the battery in the orientation indicated by the DFC labels. Battery Arrow The Charging Indicator The charging indicator shows battery charge status as follows: Charging indicator On Battery not inserted. Battery fully charged. Battery charging. Blinks Battery fault.
Inserting the Battery and a Memory Card Although the camera can store pictures in internal memory, optional SD, SDHC, and SDXC memory cards (sold separately) can be used to store additional pictures. After charging the battery, insert the battery and memory card as described below. 1 Open the battery-chamber cover. Slide the battery-chamber latch as shown and open the battery-chamber cover. 2 Insert the battery.
Inserting the Battery and a Memory Card 3 Insert the memory card. Click Q Be sure card is in the correct orientation; do not insert at an angle or use force. If the memory card is not correctly inserted or no memory card is inserted, a will appear in the display and internal memory will be used for recording and playback. Q SD/SDHC/SDXC memory cards can be locked, making it impossible to format the card or to Write-protect switch record or delete images.
Inserting the Battery and a Memory Card Removing the Battery and Memory Card Before removing the battery or memory card, turn the camera off and open the battery-chamber cover. To remove the battery, press the battery latch to the side, and slide the battery out of the camera as shown. Battery latch To remove the memory card, press it in and release it slowly. The card can then be removed by hand. When a memory card is removed, the card could be ejected too quickly.
Inserting the Battery and a Memory Card ■ Compatible Memory Cards FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_ cameras/compatibility/. Operation is not guaranteed with other cards. The camera can not be used with xD-Picture Cards or MultiMediaCard (MMC) devices.
Turning the Camera on and Off Rotate the ON/OFF switch to ON to turn the camera on. Select OFF to turn the camera off. R Press the a button to start playback. Press the shutter button halfway to return to shooting mode. R The camera will turn off automatically if no operations are performed for the length of time selected for Z POWER MANAGEMENT > AUTO POWER OFF (P 91).
Basic Setup A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as described below (you can reset the clock or change languages at any time using the F DATE/ TIME or L a options in the setup menu; for information on displaying the setup menu, see page 88). 1 Choose a language. ENGLISH R Press DISP/BACK to skip the current step. Any steps you skip will be displayed the next time the camera is turned on.
Choosing a Display The camera is equipped with a hybrid optical/electronic viewfinder (OVF/EVF) and an LCD monitor (LCD). Press VIEW MODE to choose a display.
Choosing a Display Diopter adjustment control Adjusting Display Brightness The brightness of the viewfinder and LCD monitor can be adjusted using the A SCREEN SET-UP > EVF/LCD BRIGHTNESS option in the setup menu (P 90). Bright Ambient Lighting Reflections and glare caused by bright ambient lighting may make it hard to see the display in the monitor, particularly when the camera is used outdoors. This can be addressed by holding the Q button to trigger outdoor mode.
Choosing a Display Using the Hybrid Viewfinder Use the viewfinder selector to choose between optical and electronic viewfinders. Choosing a Display Choose a display according to the task. Display 0.1 0.5 P 2000 F5.6 200 Optical viewfinder display 20 P 1.0 2000 1.5 2.0 F5.6 3.0 5.0 10 200 Electronic viewfinder display Description This display is immune from digital video effects and allows the subject to be viewed directly with no display lag.
The DISP/BACK Button The DISP/BACK button controls the display of indicators in the viewfinder and LCD monitor. ■ LCD Monitor: Shooting ■ Optical Viewfinder: Shooting 100 Detailed display Standard display 000100 F 2000 F5.6 200 P Standard display 2000 F5.6 200 P 1 Custom display 2000 5.6 F 200 0.1 0.5 P ■ Electronic Viewfinder: Shooting 100 100 0.1 0.5 P 1.0 2000 1.5 2.0 F5.6 3.0 0.1 0.5 5.0 10 200 Standard display P 1.0 2000 1.5 2.0 F5.6 3.0 1.5 2.0 3.0 F5.
The DISP/BACK Buttion ■ Viewfinder/LCD Monitor: Playback Indicators displayed Indicators hidden Favorites 1 / 1000 3 10 : 00 AM F4.5 -1 2/ 3 12 / 31 / 2050 200 100-0001 3:2 F ISO 200 1/1000 F4.5 : : OFF : : -1 2 3 3:2 F 12 / 31 / 2050 Photo information 100-0001 100-0001 10 : 00 AM 12 / 31 / 2050 10 : 00 AM Q The optical viewfinder can not be used for playback. Histograms Histograms show the distribution of tones in the image.
Basic Photography and Playback Taking Photographs This section describes how to take pictures using program AE (mode P). For information on S, A, and M modes, see page 36. 1 Select program AE. 2 Select single AF. Rotate the focus mode selector to AF-S (P 46). 3 Ready the camera. P 2000 F5.6 200 Optical viewfinder P 2000 F5.6 200 EVF/LCD The Q Button The Q button can be used to view and adjust camera settings (P 34).
Taking Photographs 4 Focus. Frame the picture with your subject in the center of the display and press the shutter button halfway to focus. R If the subject is poorly lit, the AF-assist illuminator may light (P 78). If the camera is able to focus, it will beep twice and focus area will glow green. Focus and exposure will lock while the shutter button is pressed halfway. If the camera is unable to focus, the focus frame will turn red, and s will be displayed.
Viewing Pictures Viewing Pictures Full Frame Pictures can be viewed in the viewfinder or LCD monitor. When taking important pictures, take a test shot and check the results. To view pictures full frame, press a. 100-0001 F4.5 -1 2/ 3 200 Additional pictures can be viewed by rotating the command dial or pressing it left or right. Press or rotate right to view pictures in the order recorded, left to view pictures in reverse order. Keep the dial pressed to scroll rapidly to the desired frame.
Viewing Pictures Viewing Photo Information Photo information can be viewed by pressing the command control right. 100-0001 3:2 F 12 / 31 / 2050 1 / 1000 10 : 00 AM F4.5 -1 2/ 3 D-RANGE COLOR HIGH LIGHT TONE SHADOW TONE SHARPNESS FILM SIM. WHITE BALANCE : 100 : STD : STD : STD : STD : PROVIA : AUTO Zoom indicator 200 Basic data Details, page 1 COLOR SPACE METERING EXPOSURE MODE LENS FOCAL LENGTH FLASH MODE Active focus point (“+”) : sRGB : PATTERN : PROGRAM : 18mm F2.
Viewing Pictures Multi-Frame Playback To change the number of images displayed, press n when a picture is displayed full frame. Press n to view more images. 100-0001 Use the command dial to highlight images and press MENU/OK to view the highlighted image full frame. In the nine- and hundred-frame displays, press the command dial up or down to view more pictures. Basic Photography and Playback Press k to view fewer images.
Deleting Pictures To delete individual pictures, multiple selected pictures, or all pictures, press the command dial up (b), and choose from the options below. Note that deleted pictures can not be recovered. Copy important pictures to a computer or other storage device before proceeding.
Using the Flash Use the built-in flash for additional lighting when shooting at night or indoors under low light. To choose a flash mode, press the command dial right (N) to display the following options, then rotate the dial or press it left or right to highlight an option and press MENU/OK to select. * Red-eye removal (K, L, or M) is available in these modes when ON is selected for B RED EYE REMOVAL in the shooting menu (P 79).
Using the Flash R If p is displayed when the shutter button is pressed halfway, the flash will fire when the photo is taken. R Except in commander mode, the flash may fire several times with each shot. Do not move the camera until shooting is complete. R Remove lens hoods to prevent shadows in photos taken with the flash. Q Flash is not fired in silent mode. Flash Sync Speed The flash will synchronize with the shutter at shutter speeds of 1/2000 s or slower.
Macro Mode (Close-ups) To focus at distances as close as 10 cm/4 in., press the command dial left (F) and select F. If the optical viewfinder is on, the camera will automatically switch to the electronic viewfinder (because of parallax, the camera will not focus at distances of less than 80 cm/2.6 ft. when the optical viewfinder is used). To exit macro mode, press the command dial left and select OFF.
Basic Movie Recording and Playback Recording High-Definition (HD) Movies The camera can be used to record short high-definition movies. Sound is recorded in stereo via the built-in microphone; during recording, do not cover the microphone or use the viewfinder selector, which is located next to the microphone. 1 Set aperture to A. 2 Press the DRIVE button to display drive options. Press the command dial up or down to highlight F (MOVIE) and press MENU/OK.
Viewing Movies During playback, movies are displayed as shown at right. The following operations can be performed while a movie is displayed: 100-0006 Operation Progress is shown in the display during playback. PLAY Progress bar 15s Q Do not cover the speaker during playback. Q Sound is not played back in silent mode. STOP PAUSE Playback Speed Press the command dial left or right to adjust playback speed during playback. Speed is shown Arrow by the number of arrows (M or N).
The Q (Quick Menu) Button Using the Q (Quick Menu) Button Press Q for quick access to the following items. For more information on the options available, see the pages listed below. ISO BASIC 3200 3:2 SET FINE 1 2 3 4 5 6 7 8 u SELECT CUSTOM SETTING ...................... 70 N ISO ........................................................... 44 U DYNAMIC RANGE ................................... 73 D WHITE BALANCE .................................... 42 h NOISE REDUCTION ................................
The Q (Quick Menu) Button Movie Mode In movie mode, the quick menu contains the following items: FILM SIMULATION W MOVIE MODE .......................................... 80 D WHITE BALANCE .................................... 42 P FILM SIMULATION.................................. 55 J EVF/LCD BRIGHTNESS............................
More on Photography and Playback Choosing an Exposure Mode The camera offers a choice of program AE (P), shutter-priority AE (S), aperture-priority AE (A), and manual exposure (M) modes. Program AE (P) To allow the camera to adjust both shutter speed and aperture for optimal exposure, rotate the aperture ring and shutter speed dial to A. P will appear in the display. Q If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show “– – –”. P 2000 F5.
Choosing an Exposure Mode Q If the correct exposure can not be achieved at the selected shutter speed, aperture will be displayed in red when the shutter button is pressed halfway. Adjust shutter speed until the correct exposure is achieved. Q If the subject is outside the metering range of the camera, the aperture display will show “– – –”. R Shutter speed can also be adjusted in increments of 1/3 EV by rotating the command dial. S 2000 F5.6 200 Optical viewfinder S 2000 F5.
Choosing an Exposure Mode Aperture-Priority AE (A) To adjust aperture manually while letting the camera select shutter speed for optimal exposure, rotate the shutter speed dial to A and adjust aperture. A will appear in the display. Q If the correct exposure can not be achieved at the selected aperture, the shutter speed will be displayed in red when the shutter button is pressed halfway. Adjust aperture until the correct exposure is achieved.
Choosing an Exposure Mode R The command dial and command control can be used to adjust shutter speed and aperture by ±2/3 EV from the selected value in steps of 1/3 EV. Use the command dial to adjust shutter speed, the command control to adjust aperture. M 2000 F5.6 M 200 Optical viewfinder Command dial 2000 F5.
Choosing an Exposure Mode Shutter Speed and Aperture Because the camera uses a lens-internal shutter, fast shutter speeds may not be available at large apertures. If the selected combination of shutter speed and aperture is unavailable, shutter speed or aperture will be displayed in red and the desired exposure may not be achieved. Aperture F2 F2.8 F4 F5.
Long Time-Exposures (T/B) R Use of a tripod is recommended to prevent the camera from moving during the exposure. R To reduce “noise” (mottling) in long time-exposures, select ON for K LONG EXPOSURE NR in the shooting menu (P 74). Note that this may increase the time needed to record images after shooting. Time (T) 1 Rotate the shutter speed dial to T. Bulb (B) 1 Rotate the shutter speed dial to B.
White Balance Press the command dial down (WB) to display the following options, then rotate the dial or press it left or right to highlight an option that matches the light source and press MENU/OK. The dialog shown at bottom right will be displayed; use the command dial to fine-tune white balance or press DISP/BACK to exit without fine-tuning (for an explanation of “white balance,” see the Glossary on page 118). Option Description Option Description AUTO White balance adjusted automatically.
White Balance k: Color Temperature Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources with a color temperature close to that of direct sunlight appear white; light sources with a lower color temperature have a yellow or red cast, while those with a higher color temperature are tinged with blue.
Sensitivity “Sensitivity” refers to the camera’s sensitivity to light. Choose from values between 200 and 6400, or select L (100), H (12800), or H (25600) for special situations. Higher values can be used to reduce blur when lighting is poor, while lower values allow slower shutter speeds or wider apertures in bright light; note, however, that mottling may appear in pictures taken at high sensitivities, particularly at H (25600), while choosing L (100) reduces dynamic range.
Sensitivity Option DEFAULT SENSITIVITY MAX. SENSITIVITY MIN. SHUTTER SPEED Default 200 800 1/60 The camera automatically chooses a sensitivity between the default and maximum values. Sensitivity is only raised above the default value if the shutter speed required for optimal exposure would be slower than the value selected for MIN. SHUTTER SPEED. R If the value selected for DEFAULT SENSITIVITY is higher than that selected for MAX.
Focus Mode Use the focus mode selector to choose how the camera focuses. • AF-S (single AF): Focus locks while the shutter button is pressed halfway. Choose for stationary subjects. • AF-C (continuous AF): Focus is continually adjusted to reflect changes in the distance to the subject even when the shutter button is not pressed halfway (note that this increases the drain on the battery). • MF (manual): Focus manually using the lens focus ring.
Focus Mode R The c MF ASSIST menu can be displayed by pressing and holding the center of the command control. The following options are available: • FOCUS PEAK HIGHLIGHT: Highlights high-contrast outlines. Rotate the focus ring until the subject is highlighted. • DIGITAL SPLIT IMAGE: Displays a split, black-and-white image in the center of the frame. Frame the subject in the split-image area and rotate the focus ring until the three parts of the split image are correctly aligned.
Focus Mode Focus Frame Selection When t AREA is selected for F AF MODE in the shooting menu and AF-S is selected for focus mode, the electronic viewfinder and LCD monitor offer a choice of 49 focus points and the optical viewfinder a choice of 25, allowing photographs to be composed with the main subject positioned almost anywhere in the frame. To position the focus frame, press the AF button and then use the command dial (the focus frame can be returned to the center by pressing DISP/BACK).
Focus/Exposure Lock 1 Focus: Position the subject in the focus frame and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while the shutter button is pressed halfway (AF/AE lock). P 2000 F5.6 200 R Depending on the option selected for v AE/AF-LOCK BUTTON in the shooting menu (P 78), focus and/ or exposure can also be locked by pressing the AFL/AEL button; focus and/or exposure will remain locked even when the shutter button is pressed halfway.
Focus/Exposure Lock Autofocus Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed below. • Very shiny subjects such as mirrors or car bodies. • Fast-moving subjects. • • • • Subjects photographed through a window or other reflective object. Dark subjects and subjects that absorb rather than reflect light, such as hair or fur. Insubstantial subjects, such as smoke or flame.
Exposure Compensation Exposure compensation indicator 000100 F P 1 P 2000 F5.6 200 P 2000 OVF F5.6 EVF Choose positive values (+) to increase exposure 2000 5.6 F 200 LCD 200 Exposure Value (EV) The exposure value is determined by the sensitivity of the image sensor and the amount of light to which the sensor is exposed. Doubling the amount increases EV by one, while halving it reduces EV by one.
Metering To choose how the camera meters exposure, press the AE button to display metering options. Use the command dial to highlight an option and press AE to select. Mode Description The camera instantly determines exposure based on an analysis of o composition, color, and brightness distribution. Recommended in (MULTI) most situations. The camera meters lighting conditions in an area at the center of the p frame equivalent to 2% of the total.
Using the Self-Timer 1 Press MENU/OK in shooting mode to display the shooting menu. Press P SHOOTING MENU SELF-TIMER ISO IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION FILM SIMULATION BKT the command dial up or down to highlight B SELF-TIMER and press MENU/OK. EXIT 2 Press the command dial up or down to highlight one of the following options and press MENU/OK to select. Option Description The shutter is released two seconds after the shutter button is pressed.
Using the Self-Timer 4 Press the shutter button the rest of the way down to start the timer. The display in the monitor shows the number of seconds remaining until the shutter is released. To stop the timer before the picture is taken, press DISP/BACK. The self-timer lamp on the front of the camera will blink immediately before the picture is taken. If the two-second timer is selected, the self-timer lamp will blink as the timer counts down.
Film Simulation 1 Press MENU/OK in shooting mode to display the shooting menu. Press P SHOOTING MENU SELF-TIMER ISO IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION FILM SIMULATION BKT the command dial up or down to highlight P FILM SIMULATION and press MENU/OK. OFF 200 3:2 F EXIT 2 Press the command dial up or down to highlight one of the following options and press MENU/OK to select. Option c (PROVIA/STANDARD) > (Velvia/VIVID) Description Standard color reproduction.
Bracketing Automatically vary settings over a series of pictures. 1 Press the DRIVE button to display drive options and rotate the dial or press it up or down to highlight one of the following: ±1 ±2/ 3 ±1/ 3 AE BKT Option Description Press the command dial left or right to highlight a bracketing amount.
Multiple Exposures 4 Press MENU/OK. You will be prompted to take the second shot. + 1 Press the DRIVE button to display drive options. R To return to Step 2 and retake the first shot, press the command dial left. To save the first shot and exit without creating a multiple exposure, press DISP/BACK. STILL IMAGE 5 Take the second shot. 2 Press the command dial up or down to highlight n MULTIPLE EXPOSURE and press MENU/OK. 3 Take the first shot.
Continuous Shooting (Burst Mode) Capture motion in a series of pictures. 1 Press the DRIVE button to display drive op- 4 Press the shutter button the rest tions. Press the command dial up or down to highlight I (CONTINUOUS), and the options shown below will be displayed. of the way down to start shooting. Shooting ends when the shutter button is released, the selected number of pictures has been taken, or the memory card is full.
Continuous Shooting (Burst Mode) Position in burst/total number of pictures in burst PLAY CONTINUOUS SHOTS PLAY NORMAL 1/ 10 First picture in burst R Pressing the command dial right when the last picture in the burst is displayed displays the first picture in the burst; similarly, pressing the command dial left when the first picture is displayed displays the last picture.
Panoramas Follow an on-screen guide to create a panorama. 1 Press the DRIVE button to display drive op- 5 Pan the camera in the direction shown by the tions. Press the command dial up or down to highlight r (MOTION PANORAMA) and press MENU/OK. arrow. Shooting ends automatically when the camera is panned to the end of the guides and the panorama is complete. MOTION PANORAMA 2 To select the size of the angle through which you will pan the camera while shooting, press the command dial left.
Panoramas For Best Results For best results, prop your elbows against your sides and move the camera slowly in a small circle at a steady speed, keeping the camera horizontal and being careful only to pan in the direction shown by the guides. Use a tripod for best results. If the desired results are not achieved, try panning at a different speed. More on Photography and Playback Q Panoramas are created from multiple frames; exposure for the entire panorama is determined by the first frame.
Panoramas Viewing Panoramas In full-frame playback, panoramas can be played back using the command dial. Press the command dial down to start playback and press again to pause. While playback is paused, you can scroll the panorama manually be pressing the command dial left or right. To exit to full-frame playback, press the command dial up.
Recording Pictures in RAW Format R RAW images record raw, unprocessed data from the camera image sensor. JPEG copies of RAW images can be created using the j RAW CONVERSION option in the playback menu, or RAW images can be viewed on a computer using the RAW FILE CONVERTER application that is installed with the software on the supplied CD (P 94, 95). R Sensitivities of L (100), H (12800), and H (25600) are not available when RAW image quality is on (P 44).
Recording Pictures in RAW Format Creating JPEG Copies of RAW Pictures RAW pictures store information on camera settings separately from the data captured by the camera image sensor. Using the j RAW CONVERSION option in the playback menu, you can create JPEG copies of RAW pictures using different options for the settings listed below. The original image data are unaffected, allowing a single RAW image to be processed in a multitude of different ways.
The ND Filter 1 Press MENU/OK in shooting mode to display the shooting menu. Press P SHOOTING MENU ND FILTER COLOR SHARPNESS HIGHLIGHT TONE SHADOW TONE NOISE REDUCTION LONG EXPOSURE NR the command dial up or down to highlight t ND FILTER and press MENU/OK. EXIT 2 Press the command dial up or down to highlight ON and press MENU/OK to select. OFF 0 0 0 0 0 ON More on Photography and Playback The camera is equipped with a Neutral Density (ND) filter that reduces exposure by the equivalent of 3 EV.
Image Search Follow the steps below to search for pictures. 1 Press MENU/OK during playback to display the playback menu. Press the command dial up or down to highlight b IMAGE SEARCH and press MENU/OK. 2 Highlight an option and press MENU/OK. Option BY DATE BY FACE BY I FAVORITES BY TYPE OF DATA BY UPLOAD MARK Description Search by date. Search for pictures that include faces. Search by rating (P 25). Find all still pictures, all movies, all pictures taken in burst mode, or all RAW pictures.
PhotoBook Assist Creating a PhotoBook 1 Select NEW BOOK for m PHOTOBOOK ASSIST in the playback menu (P 85) and choose from the following options: • SELECT FROM ALL: Choose from all available pictures. • SELECT BY IMAGE SEARCH: Choose from pictures matching selected search conditions (P 66). R Neither photographs a or smaller nor movies can be selected for photobooks.
PhotoBook Assist Viewing Photobooks Highlight a book in the photobook assist menu and press MENU/OK to display the book, then press the command dial left or right to scroll through the pictures. Editing and Deleting Photobooks Display the photobook and press MENU/OK. The following options will be displayed; select the desired option and follow the on-screen instructions. • EDIT: Edit the book as described in “Creating a PhotoBook” (P 67). • ERASE: Delete the book.
The Fn Button R The F Fn BUTTON menu can also be displayed by pressing and holding the Fn button. More on Photography and Playback The role played by the Fn button can be selected using the F Fn BUTTON option in the shooting menu (P 74).
Saving Settings Save up to 3 sets of custom camera settings for commonly-encountered situations. Saved settings can be recalled using the u SELECT CUSTOM SETTING option in the shooting menu. 1 Press MENU/OK in shooting mode to display the shooting menu. Press P SHOOTING MENU SELECT CUSTOM SETTING EDIT/SAVE CUSTOM SETTING Fn BUTTON DISP. CUSTOM SETTING FRAMING GUIDLINE WIDE CONVERSION LENS MF ASSIST the command dial up or down to highlight K EDIT/SAVE CUSTOM SETTING and press MENU/OK.
Advanced Movie Recording Q Movies recorded when the aperture is displayed in red will not be correctly exposed. Before Recording Before recording, adjust movie settings (P 80), aperture (P 38), and exposure compensation (P 51) and select a focus mode (P 46). These settings can not be adjusted during recording. Using an External Microphone The camera can be used with optional MIC-ST1 stereo microphones using the cable supplied with the MIC-ST1. See the microphone manual for details.
Menus Using the Menus: Shooting Mode The shooting menu is used to adjust settings for a wide range of shooting conditions. To display the shooting menu, press MENU/OK in shooting mode. Highlight items and press the command dial right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete.
Using the Menus: Shooting Mode (default: FINE) T IMAGE QUALITY Choose a file format and compression ratio. Select FINE or NORMAL to record JPEG images, RAW to record RAW images, or FINE+RAW or NORMAL+RAW to record both JPEG and RAW images. FINE and FINE+RAW use lower JPEG compression ratios for higher-quality JPEG images, while NORMAL and NORMAL+RAW use higher JPEG compression ratios to increase the number of images that can be stored. U DYNAMIC RANGE (default: V) Control contrast.
Using the Menus: Shooting Mode f COLOR Adjust color density. (default: MID) q SHARPNESS Sharpen or soften outlines. (default: STANDARD) r HIGHLIGHT TONE Adjust the appearance of highlights. (default: STANDARD) s SHADOW TONE Adjust the appearance of shadows. (default: STANDARD) h NOISE REDUCTION Reduce noise in pictures taken at high sensitivities. (default: STANDARD) K LONG EXPOSURE NR Select ON to reduce mottling in long time-exposures (P 41).
Using the Menus: Shooting Mode v DISP. CUSTOM SETTING Choose the items displayed in the viewfinder and LCD monitor (P 21).
Using the Menus: Shooting Mode c FRAMING GUIDLINE Choose the type of framing grid available in shooting mode. F GRID 9 P For “rule of thirds” composition. (default: F GRID 9) G GRID 24 H HD FRAMING A six-by-four grid. Frame HD pictures in the crop shown by the lines at the top and bottom of the display. P P Y WIDE CONVERSION LENS Select ON when using the an optional wide conversion lens (P 108). c MF ASSIST Choose how focus is displayed in manual focus mode (P 47).
Using the Menus: Shooting Mode d ADVANCED FILTER Take photos with filter effects. Choose from the following filters. Description Choose for a retro toy camera effect. The tops and bottoms of pictures are blurred for a diorama effect. Create high-contrast images with saturated colors. Create bright, low-contrast images. Create uniformly dark tones with few areas of emphasized highlights. Dynamic tone expression is used for a fantasy effect. Create a look that is evenly soft throughout the whole image.
Using the Menus: Shooting Mode C AF ILLUMINATOR If ON is selected, the AF-assist illuminator will light to assist autofocus. (default: ON) R The AF-assist illuminator turns off automatically in silent mode. Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro mode, try increasing the distance to the subject. Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
Using the Menus: Shooting Mode (default: ±0) I FLASH Adjust flash brightness. Choose from values between +2/3 EV and –2/3 EV. Note that the desired results may not be achieved depending on shooting conditions and the distance to the subject. B RED EYE REMOVAL Choose ON to remove red-eye effects caused by the flash. (default: OFF) R Red-eye reduction is performed only when a face is detected. R Red-eye removal is not available with RAW images.
Using the Menus: Shooting Mode Shooting Menu Options (Movie Mode) The following options are available in movie mode (P 32). W MOVIE MODE (default: i 1920×1080 (30fps)) Select a frame rate for movie recording. Choose from rates of 30 and 60 fps; frame size is fixed at 1920 × 1080 (Full HD). P FILM SIMULATION Simulate the effects of different types of film (P 55). t MIC LEVEL ADJUSTMENT Adjust the microphone recording level. (default: c PROVIA/STANDARD) (default: 3) v DISP.
Using the Menus: Playback Mode To display the playback menu, press MENU/OK in playback mode. Highlight items and press the command dial right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete. PLAYBACK MENU RAW CONVERSION ERASE CROP RESIZE PROTECT IMAGE ROTATE COPY EXIT Playback Menu Options j RAW CONVERSION Create JPEG copies of RAW pictures (P 64). A ERASE Delete all or selected pictures (P 28).
Using the Menus: Playback Mode e RESIZE Create a cropped copy of the current picture. 1 Display the desired picture. 2 Select e RESIZE in the playback menu. 3 Highlight a size and press MENU/OK to display a confirmation dialog. 4 Press MENU/OK again to save the resized copy to a separate file. R The sizes available vary with the size of the original image. D PROTECT Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK. • FRAME: Protect selected pictures.
Using the Menus: Playback Mode C IMAGE ROTATE Rotate pictures. 1 Display the desired picture. 2 Select C IMAGE ROTATE in the playback menu. 3 Press the command dial down to rotate the picture 90° clockwise, up to rotate it 90° counterclockwise. 4 Press MENU/OK. The picture automatically be displayed in the selected orientation whenever it is played back on the camera. R Protected pictures can not be rotated. Remove protection before rotating pictures.
Using the Menus: Playback Mode B RED EYE REMOVAL Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create a copy with reduced red-eye. 1 Display the desired picture. 2 Select B RED EYE REMOVAL in the playback menu. 3 Press MENU/OK. R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on the scene.
Using the Menus: Playback Mode m PHOTOBOOK ASSIST Create books from your favorite photos (P 67). j MARK FOR UPLOAD TO Select pictures for upload to YouTube, Facebook or MyFinePix.com using MyFinePix Studio (Windows only). 1 Highlight an option and press MENU/OK. Select YouTube to choose movies for upload to YouTube, FACEBOOK to choose photos and movies for upload to Facebook, or MyFinePix.com to choose photos for upload to MyFinePix.com.
Using the Menus: Playback Mode K PRINT ORDER (DPOF) Select pictures for printing on DPOF- and PictBridge-compatible devices (P 101). J DISP ASPECT Choose how High Definition (HD) devices display pictures with an aspect ratio of 3 : 2 (this option is available only when an HDMI cable is connected). Select 16 : 9 to display the image so that it fills the screen with its top and bottom cropped out, 3 : 2 to display the entire image with black bands at either side.
The Setup Menu Using the Setup Menu 1 Display the setup menu. 1.1 Press MENU/OK to display the menu for the current mode. 1.2 Press the command dial left to highlight the tab for the current menu. 1.3 Press the command dial down to highlight Z. SET-UP DATE/TIME TIME DIFFERENCE ENGLISH RESET SILENT MODE FRAME NO. FOCUS RING OFF CONT. Menus EXIT Tab 1.4 Press the command dial right to place the cursor in the setup menu. 2 Adjust settings.
The Setup Menu Setup Menu Options F DATE/TIME Set the camera clock (P 17). N TIME DIFFERENCE (default: h) Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between local time and your home time zone: 1 Highlight g LOCAL and press MENU/OK. 2 Use the command dial to choose the time difference between local time and your home time zone. Press MENU/OK when settings are complete.
The Setup Menu (default: CONTINUOUS) B FRAME NO. New pictures are stored in image files named using a four-digit file number assigned by adding one to the Frame number last file number used. The file number is displayed during playback as shown at right. B FRAME NO. con100-0001 trols whether file numbering is reset to 0001 when a new memory card is inserted or the current memory card is formatted.
The Setup Menu b SOUND SET-UP Adjust sound settings. Option OPERATION VOL. SHUTTER VOLUME SHUTTER SOUND Description Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF (mute) to disable control sounds. Adjust the volume of the sounds produced when the shutter is released. Choose e OFF (mute) to disable the shutter sound. Choose the sound made by the shutter. A SCREEN SET-UP Adjust display settings.
The Setup Menu Z POWER MANAGEMENT Adjust power management settings. Option Description Choose the length of time before the camera turns off automatically when no operations are performed. AUTO POWER OFF Shorter times reduce the drain on the battery; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera turns off automatically even when OFF is selected.
The Setup Menu (default: ON) b Eye-Fi TRANSFER The camera can be used with third-party Eye-Fi cards; for more information see the manual provided with the card or contact the manufacturer. Option ON OFF Description Pictures taken with the camera are uploaded to a pre-selected destination. Pictures are not uploaded automatically. Q Observe local regulations regarding the use of wireless devices when using Eye-Fi cards.
Connections Viewing Pictures on a Computer The supplied software can be used to copy pictures to a computer, where they can be stored, viewed, organized, and printed. Before proceeding, install the software as described below. Do NOT connect the camera to the computer until installation is complete.
Viewing Pictures on a Computer 3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive. Windows 8/Windows 7/Windows Vista If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed; click Yes (Windows 8/Windows 7) or Allow (Windows Vista). The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio and RAW FILE CONVERTER.
Viewing Pictures on a Computer Macintosh: Installing RAW FILE CONVERTER RAW FILE CONVERTER is used to view RAW images on your computer. 1 Confirm that the computer meets the following system requirements: CPU Intel (Core 2 Duo or better) Pre-installed copies of Mac OS X version 10.6–10.8 (visit http://www.fujifilm.com/support/digital_cameras/ OS compatibility/ for more information).
Viewing Pictures on a Computer Importing Pictures or Movies to Mac (Macintosh) Use a standard application in Mac OS such as Image Capture to import pictures or movies to Mac.
Viewing Pictures on a Computer Connecting the Camera 1 If the pictures you wish to copy are stored on a memory card, insert the card into the camera (P 12). R Windows users may require the Windows CD when starting the software for the first time. Q Loss of power during transfer could result in loss of data or damage to internal memory or the memory card. Charge the battery before connecting the camera.
Viewing Pictures on a Computer Q If a memory card containing a large number of images is inserted, there may be a delay before the software starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Printing Pictures via USB If the printer supports PictBridge, the camera can be connected directly to the printer and pictures can be printed without first being copied to a computer. Note that depending on the printer, not all the functions described below may be supported. Connecting the Camera 1 Connect the supplied USB cable as shown and turn the printer on. Printing Selected Pictures 1 Press the command dial left or right to display a picture you wish to print.
Printing Pictures via USB Printing the Date of Recording To print the date of recording on pictures, press DISP/BACK in the PictBridge display and select PRINT WITH DATE s (to print pictures without the date of recording, select PRINT WITHOUT DATE). To ensure that the date is correct, set the camera clock before taking pictures. Some printers do not support date printing. See the printer manual for details.
Printing Pictures via USB During Printing The message shown at right is displayed during printing. Press DISP/BACK to cancel before all pictures are printed (depending on the printer, printing may end before the current picture has printed). PRINTING Creating a DPOF Print Order The K PRINT ORDER (DPOF) option in the playback menu can be used to create a digital “print order” for PictBridge-compatible printers or devices that support DPOF.
Printing Pictures via USB ■ WITH DATE s/ WITHOUT DATE To modify the DPOF print order, select K PRINT ORDER (DPOF) in the playback menu and press the command dial up or down to highlight WITH DATE s or WITHOUT DATE. PLAYBACK Y MENU RED EYE REMOVAL SLIDE SHOW WITH DATE s PHOTOBOOK ASSIST WITHOUT DATE MARK FOR UPLOAD TO RESET ALL IMAGE SEARCH PRINT ORDER (DPOF) DISP ASPECT WITH DATE s: Print date of recording on pictures. WITHOUT DATE: Print pictures without date.
Printing Pictures via USB 4 The total number of prints is displayed in the monitor. Press MENU/ OK to exit. The pictures in the current print order are indicated by a u icon during playback. ■ RESET ALL To cancel the current print order, select RESET ALL for K PRINT ORDER (DPOF). The confirmation shown at right will be displayed; press MENU/OK to remove all pictures from the order. RESET DPOF OK? YES CANCEL Connections R Print orders can contain a maximum of 999 pictures.
Viewing Pictures on TV To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately from third-party suppliers; note that the TV can only be used for playback, not shooting). 1 Turn the camera off. 2 Connect the cable as shown below. Insert into HDMI connector Insert into HDMI mini connector R Be sure the connectors are fully inserted. 3 Tune the television to the HDMI input channel. See the documentation supplied with the television for details.
Technical Notes Optional Accessories The camera supports a wide range of accessories from FUJIFILM and other manufacturers. Accessories from FUJIFILM The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/ products/digital_cameras/index.html.
Optional Accessories Leather cases LC-X100S: This leather case, exclusively for use with the X100S/X100, combines practicality with the luxury of leather and comes with a shoulder strap made of the same material. Pictures can be taken and batteries and memory cards inserted or removed with the camera still in its case. Adapter rings AR-X100: An aluminum adapter ring exclusively for use with the X100S/X100.
Optional Accessories Attaching Adapter Rings 1 Remove the front ring. R If you have trouble removing the front ring, grip the entire ring and rotate it as shown. Attaching Lens Hoods Attach the adapter ring before attaching the lens hood. R Align the indentations and rotate as shown. 2 Attach the adapter ring Q Keep the front ring and lens cap in a safe place when not in use. Q Attach the adapter ring before attaching LH-X100 lens hood, PRF-49S protector filter, or third-party filters.
Optional Accessories The WCL-X100 Wide Conversion Lens A Y WIDE CONVERSION LENS option has been added to the shooting menu for use with the optional WCL-X100 wide conversion lens. Select ON when using the WCL-X100. R A Y icon is displayed when ON is selected. P 2000 F5.6 200 R Because the optical viewfinder does not cover the full field of view of the conversion lens, the bright frame is replaced by brackets showing approximately 80% of the field of view.
Optional Accessories Connecting the Camera to Other Devices ■ Remote Shutter Release ■ External Microphones Remote release † ■ Printing MIC-ST1 stereo microphone * X100S ■ Flash Photography USB cable (supplied) PictBridge-compatible printer † Printer † EF-20 shoe mount EF-42 shoe mount flash * flash * ■ Audio/Visual ■ Computer Related HDMI cable † USB cable (supplied) EF-X20 shoe mount flash * Technical Notes SD/SDHC/SDXC memory card † HDTV † Computer † * Available separately from FUJIFILM.
Caring for the Camera To ensure continued enjoyment of the product, observe the following precautions. Storage and Use If the camera will not be used for an extended period, remove the battery and memory card.
Troubleshooting Problems and Solutions ■ Power and Battery Problem The camera does not turn on. The monitor does not turn on. The battery runs down quickly. The battery is exhausted exhausted:: Charge the battery ((P P 11) or insert a fully-charged spare battery ((P P 12). Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P P 11). Charge the battery at room temperature ((P P iv).
Problems and Solutions ■ Shooting Problem No picture is taken when the shutter button is pressed. • • • • • • • Solution P 12, 28). Memory is full: Insert a new memory card or delete pictures ((P P 92). Memory is not formatted: Format the memory card or internal memory ((P There is dirt on the memory card contacts contacts:: Clean the contacts with a soft, dry cloth. The memory card is damaged damaged:: Insert a new memory card ((P P 12).
Problems and Solutions Problem Solution Some flash modes are not The camera is in silent mode. Turn silent mode off (P (P 5). available. • The subject is not in range of the flash ash:: Position the subject in range of the flash ((P P 121). The flash does not fully • The flash window is obstructed obstructed:: Hold the camera correctly ((P P 23). light the subject. • Shutter speed is faster than 1/2000 ss:: Choose a slower shutter speed ((P P 30, 37, 39). • The lens is dirty dirty:: Clean the lens ((P P ix).
Problems and Solutions ■ Connections/Miscellaneous Problem No picture or sound. The computer does not recognize the camera. Can not transfer RAW or JPEG files to computer. Pictures can not be printed. Only one copy is printed/ the date is not printed. The camera is unresponsive. The camera does not function as expected. No sound. 114 Solution • The camera is not properly connected: connected: Connect the camera properly (P (P 104).).
Warning Messages and Displays The following warnings appear in the display. Warning B (red) A (blinks red) k s (displayed in red with red focus frame) Aperture or shutter speed displayed in red FOCUS ERROR TURN OFF THE CAMERA AND TURN ON AGAIN LENS CONTROL ERROR BUSY PROTECTED CARD Camera malfunction. Turn the camera off and then on again. If the message persists, contact a FUJIFILM dealer. The memory card is incorrectly formatted. Use the camera to format the card ((P P 92).
Warning Messages and Display Warning CARD ERROR Description • The memory card is not formatted for use in the camera camera:: Format the card (P (P 92). • The memory card contacts require cleaning or the memory card is damaged damaged:: Clean the contacts with a soft, dry cloth. If the message is repeated, format the card (P (P 92). If the message persists, replace the card. • Incompatible memory card: card: Use a compatible card ((P P 15). • Camera malfunction: malfunction: Contact a FUJIFILM dealer.
Warning Messages and Display Warning TOO MANY FRAMES PROTECTED FRAME CAN NOT CROP m CANNOT EXECUTE F CANNOT EXECUTE CAN NOT ROTATE F CAN NOT ROTATE b NO IMAGE a NO IMAGE Description • A search has returned more than 30,000 results: results: Choose a search that returns fewer results. • More than 999 images are selected for deletion deletion:: Choose fewer images. An attempt was made to delete or rotate to a protected picture. Remove protection and try again ((P P 82).
Appendix Glossary Exif Print: A standard for storing information with pictures for optimal color reproduction during printing. HDMI (High-Definition Multimedia Interface): An interface standard for the transmission of images and sound that adds audio input to the DVI interface used to connect computers to displays. JPEG (Joint Photographic Experts Group): A compressed file format for color images.
Memory Card Capacity The following table shows the recording time or number of pictures available at different image sizes. All figures are approximate; file size varies with the scene recorded, producing wide variations in the number of files that can be stored. The number of exposures or length remaining may not diminish at an even rate. A limited number of test pictures can be taken when no memory card is inserted.
Specifications System Model Effective pixels Image sensor Storage media File system File format Image size Lens Focal length Maximum aperture Aperture Focus range (distance from front of lens) Sensitivity Metering Exposure control Exposure compensation 120 FUJIFILM X100S digital camera 16.3 million 23.6 × 15.6 mm (APS-C), X-Trans CMOS II sensor with square pixels and primary color filter • Internal memory (approx.
Specifications System Shutter speed (mechanical shutter) Continuous Focus White balance Self-timer Flash Mode Hot shoe Hybrid viewfinder LCD monitor Movies • P mode mode:: / sec. to / sec. • Time Time:: 30 sec. to / sec. • Bulb Bulb:: Max. 60 min. • All other modes: modes: 60 min. to / sec. Choose from frame rates of 3.0 or 6.0 fps (JPEG); max.
Specifications Input/output terminals HDMI output HDMI mini connector Digital input/output USB 2.0 High-Speed Power supply/other Power supply NP-95 rechargeable battery Battery life (approximate Battery type Approximate number of frames number of frames that can NP-95 (type supplied with camera) 330 be taken with a fully-charged CIPA standard, measured using battery supplied with camera and SD memory card.
Specifications NP-95 rechargeable battery Nominal voltage DC 3.6 V Nominal capacity 1,800 mAh Operating temperature 0 °C to +40 °C/+32 °F to +104 °F Dimensions (W × H × D) 35.2 mm × 49.5 mm × 10.8 mm / 1.3 in. × 1.9 in. × 0.4 in. Weight Approx. 39 g / 1.3 oz. BC-65N battery charger Rated input Input capacity Rated output Supported batteries Charging time Operating temperature Dimensions (W × H × D) Weight 100 V – 240 V AC, 50/60 Hz 15 VA 4.2 V DC, 650 mA NP-95 rechargeable batteries Approx.
Specifications ■ Notices • Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/ digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual. • Although the viewfinder and LCD monitor are manufactured using advanced high-precision technology, small bright points and anomalous colors may appear, particularly in the vicinity of text.
Restrictions on Camera Settings The options available in each shooting mode are listed below. Option OFF F (macro mode) F 6.0 fps I (continuous) 3.
Restrictions on Camera Settings Option O IMAGE SIZE T IMAGE QUALITY U DYNAMIC RANGE P FILM SIMULATION 126 O P Q FINE NORMAL FINE+RAW NORMAL+RAW RAW AUTO V W X c d e g h b e d f f P ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ S ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ A ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ M ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ n ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ rF ✔3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Option t ND FILTER f COLOR q SHARPNESS
Restrictions on Camera Settings Option P S A M nrF ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ P ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ S ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ A ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ M ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ nrF ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5 ✔ ✔5 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔4 ✔4 ✔ ✔ ✔ Appendix ✔ ✔ ✔ ✔ ✔ Option c FRAMING GUIDLINE Y WIDE CON
Restrictions on Camera Settings Option I FLASH B RED EYE REMOVAL n SAVE ORG IMAGE I FOCUS RING j FOCUS CHECK Z POWER MANAGEMENT J COLOR SPACE 128 P ✔ ✔ ✔ ✔ ✔ ✔ ✔ S ✔ ✔ ✔ ✔ ✔ ✔ ✔ A ✔ ✔ ✔ ✔ ✔ ✔ ✔ M ✔ ✔ ✔ ✔ ✔ ✔ ✔ nrF ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ 1 2 3 4 5 Fixed at OFF OFF.. Fixed at o (multi). Fixed at Q. Center focus area selected automatically. Options available vary with shooting mode.
Memo 129
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN http://www.fujifilm.com/products/digital_cameras/index.