BL04701-101 DIGITAL CAMERA X-T1 Owner’s Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM X-T1 digital camera and install the supplied software. Be sure that you have read and understood its contents before using the camera.
For Your Safety IMPORTANT SAFETY INSTRUCTIONS • Read Instructions Instructions: All the safety and operating instructions should be read before the appliance is operated. • Retain Instructions Instructions: The safety and operating instructions should be retained for future reference. • Heed Warnings Warnings: All warnings on the appliance and in the operating instructions should be adhered to. • Follow Instructions Instructions: All operating and use instructions should be followed.
For Your Safety Service Be sure to read these notes before use Servicing: Do not attempt to service this video product Safety Notes yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to • Make sure that you use your camera correctly. Read these qualified service personnel. safety notes and your Owner’s Manual carefully before use.
For Your Safety WARNING Use only batteries or AC power adapters specified for use with this camera. Do not use voltages other than the power supply voltage shown. The use of other power sources can cause a fire. If the battery leaks and fluid gets in contact with your eyes, skin or clothing, flush the affected area with clean water and seek medical attention or call an emergency number right away. Do not use the charger to charge batteries other than those specified here.
For Your Safety ■ Battery Life At normal temperatures, the battery can be recharged about 300 times. A noticeable decrease in the length of time the battery will hold a charge indicates that it has reached the end of its service life and should be replaced. ■ Storage Performance may be impaired if the battery is left unused for extended periods when fully charged. Run the battery flat before storing it.
For Your Safety Using the Camera • Do not aim the camera at extremely bright light sources, such as the sun in a cloudless sky. Failure to observe this precaution could damage the camera image sensor. • Strong sunlight focused through the viewfinder may damage the panel of electronic viewfinder (EVF). Do not aim the electronic viewfinder at the sun. Liquid Crystal In the event that the display is damaged, care should be taken to avoid contact with liquid crystal.
For Your Safety For Customers in the U. S. A. Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
For Your Safety Be sure to read these notes before use Safety Notes Thank you for your purchase of this product. For repair, inspection, and internal testing, contact your FUJIFILM dealer. • Make sure that you use the lens correctly. Read these safety notes and the camera Owner’s Manual carefully before use. • After reading these safety notes, store them in a safe place.
For Your Safety European Union regulatory notice This product complies with the following EU Directives: • Low Voltage Directive 2006/95/EC • EMC Directive 2004/108/EC • R & TTE Directive 1999/5/EC Wireless Network Devices: Cautions • This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters.
About This Manual Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information on specific topics, consult the sources below. Table of Contents ................................................. P xii The “Table of Contents” gives an overview of the entire manual. The principal camera operations are listed here. Troubleshooting ................................................P ................................................
Product Care Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body. Any liquid on the camera should be removed immediately with a soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then gently wipe with a soft, dry cloth.
Table of Contents For Your Safety .....................................................................................ii IMPORTANT SAFETY INSTRUCTIONS.........................................ii Safety Notes .......................................................................................iii NOTICES ...............................................................................................vi Safety Notes .....................................................................................
Table of Contents Basic Movie Recording and Playback More on Photography and Playback Recording High-Definition (HD) Movies ............................... 31 Using an External Microphone ................................................. 32 Viewing Movies ................................................................................ 33 Choosing an Exposure Mode ..................................................... 46 Program AE (P) ......................................................................
Table of Contents Long Time-Exposures (T/B) ......................................................... 64 Time (T) .............................................................................................. 64 Bulb (B) ............................................................................................... 64 Interval Timer Photography....................................................... 65 Using a Remote Release ..............................................................
Table of Contents Using the Menus: Playback Mode............................................ 83 Playback Menu Options .............................................................. 83 r WIRELESS COMMUNICATION ........................................... 83 j RAW CONVERSION ............................................................... 83 A ERASE ........................................................................................ 83 G CROP..................................................................
Table of Contents Connections Technical Notes Wireless Transfer .............................................................................. 97 Wireless Connections: Smartphones ..................................... 97 Wireless Connections: Computers .......................................... 97 Viewing Pictures on a Computer .............................................. 98 Windows: Installing MyFinePix Studio .................................. 98 Macintosh: Installing RAW FILE CONVERTER..............
Before You Begin Symbols and Conventions Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may be simplified for explanatory purposes. Supplied Accessories Before You Begin The following symbols are used in this manual: Q This information should be read before use to ensure correct operation. R Additional information that may be helpful when using the camera. POther pages in this manual on which related information may be found.
Parts of the Camera For more information, refer to the page listed to the right of each item. The LCD Monitor The LCD monitor can be tilted for easier viewing, but be careful not to touch the wires or trap fingers or other objects behind the monitor. Touching the wires could cause camera malfunction.
Parts of the Camera i FOCUS ASSIST button ......................................62 j Memory card slot cover.....................................15 k Q (quick menu) button .....................................34 Custom settings button (press and hold) * RAW conversion button (playback mode) .........70 l Selector/function buttons...................................4 m DISP (display)/BACK button ............................21 n Speaker.............................................................
Parts of the Camera The Selector Press the selector up (w), right (r), down (t), or left (e) to highlight items and press MENU/OK (q) to select. The up, left, right, and down buttons also double as the Fn3, Fn4, Fn5, and Fn6 buttons, respectively (P 39, 41, 42, 43, 45). The Indicator Lamp When the viewfinder is not in use (P 19), the indicator lamp shows camera status. Indicator lamp Glows green Blinks green Blinks green and orange Glows orange Blinks orange Blinks red Camera status Focus locked.
Parts of the Camera ■ Shooting: LCD Monitor/Viewfinder LCD monitor Viewfinder 100 +1 100 F 100 +1 +1 F Before You Begin Camera Displays The following types of indicator may be displayed during shooting and playback. In the description that follows, all available indicators are shown for illustrative purposes; the indicators actually displayed vary with camera settings. Note that the LCD monitor and electronic viewfinder have different aspect ratios. 3 2 1 0 1 2 3 0.1 0.5 P 1.0 2000 1.5 2.
Parts of the Camera ■ Shooting: LCD Monitor 000100 +1 3 2 1 F 0 1 2 3 P 1 2000 5.6 F 200 A Self-timer indicator ..........................................35 M Battery level .....................................................17 B Flash mode .......................................................36 N Sensitivity.........................................................50 Flash compensation ..........................................81 O Aperture ...............................................
Lenses The camera can be used with lenses for the FUJIFILM X-mount. Parts of the Lens Before You Begin Removing the Caps Remove the caps as shown. Q Lens caps may differ from those shown. A Lens hood B Mounting marks C Focus ring D Zoom ring E Aperture ring F O.I.S. switch G Aperture mode switch H Lens signal contacts I Front lens cap J Rear lens cap Attaching the Hood When attached, lens hoods reduce glare and protect the front lens element.
Lenses Lenses with Aperture Rings At settings other than A, you can adjust aperture by rotating the lens aperture ring (exposure modes A and M). Aperture ring A 16 11 8 5.6 4 2.8 A 16 11 8 5.6 4 Lenses with No Aperture Rings The method used to adjust aperture can be selected using the e APERTURE SETTING option (P 82) in the shooting menu. When an option other than AUTO is selected, aperture can be adjusted using the rear command dial.
Lenses O.I.S. switch Manual Focus Lenses Slide the focus ring to the front for autofocus. For manual focus, slide the focus ring to the back and rotate it while checking the results in the camera display. The focus distance and depth-of-field indicators can be used to assist manual focus. Note that manual focus may not be available in all shooting modes. Before You Begin Lenses with O.I.S. Switches If the lens supports optical image stabilization (O.I.S.
First Steps Attaching the Strap Attach the strap clips to the camera and then attach the strap. 1 Open a strap clip. Use the clip attaching tool to open a strap clip, making sure that the tool and clip are in the orientations shown. 3 Pass the clip through the eyelet. Rotate the clip fully through the eyelet until it clicks closed. 4 Attach a protective cover. Q Keep the tool in a safe place. You will need it to open the strap clips when removing the strap. 2 Place the strap clip on an eyelet.
Attaching the Strap 5 Insert the strap. Insert the strap through a protective cover and strap clip. 6 Fasten the strap. Fasten the strap as shown. Repeat Steps 5–6 for the second eyelet. First Steps Q To avoid dropping the camera, be sure the strap is correctly secured.
Attaching a Lens Lenses attach as described below. Q Care is required to prevent dust entering the camera while attaching and removing lenses. 1 Remove the body and rear caps. Remove the body cap from the camera and the rear cap from the lens. Removing Lenses To remove the lens, turn the camera off, then press the lens release button and rotate the lens as shown. Lens release button Q Do not touch the camera’s internal parts. 2 Attach the lens.
Charging the Battery The battery is not charged at shipment. Before use, charge the battery in the supplied battery charger. 1 Place the battery in the charger. Place the battery in the supplied battery charger as shown. Charge lamp Plug the charger into an indoor power outlet. The charging indicator will light. The Charging Indicator The charging indicator shows battery charge status as follows: Charging indicator Arrow On Battery not inserted. Battery fully charged. Battery charging.
Inserting the Battery After charging the battery, insert the battery as described below. 1 Open the battery-chamber cover. Slide the battery-chamber latch as shown and open the battery-chamber cover. 2 Insert the battery. Using the battery to keep the battery latch pressed to one side, insert the battery contacts first in the direction shown by the arrow. Confirm that the battery is securely latched. Arrow Q Do not open the battery-chamber cover when the camera is on.
Inserting a Memory Card The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC memory cards (sold separately). Memory cards are inserted as described below. 1 Open the memory card slot cover. 3 Close the memory card slot cover. Turn the camera off and open the memory card slot cover. First Steps 2 Insert the memory card. Holding the memory card in the orientation shown, slide it in until it clicks into place at the back of the slot.
Inserting a Memory Card ■ Compatible Memory Cards FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_ cameras/compatibility/. Operation is not guaranteed with other cards. The camera can not be used with xD-Picture Cards or MultiMediaCard (MMC) devices.
Turning the Camera on and Off Rotate the ON/OFF switch to ON to turn the camera on. Select OFF to turn the camera off. Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder. Keep the lens and viewfinder clean. First Steps R Press the a button to start playback. Press the shutter button halfway to return to shooting mode.
Basic Setup A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as described below (you can reset the clock or change languages at any time using the F DATE/TIME or Q a options in the setup menu; for information on displaying the setup menu, see page 89). 1 Choose a language. Highlight a language and press MENU/OK. START MENU ENGLISH R Press DISP/BACK to skip the current step. Any steps you skip will be displayed the next time the camera is turned on.
Display Settings The camera is equipped with an electronic viewfinder (EVF) and an LCD monitor (LCD). Choosing a Display Press the VIEW MODE button to cycle through displays as shown below.
Display Settings The Viewfinder Display When ON is selected for A SCREEN SET-UP > EVF AUTOROTATE DISPLAYS in the setup menu (P 90), the indicators in the viewfinder automatically rotate to match camera orientation. 100 0.1 0.5 P 1.0 2000 1.5 2.0 3.0 5.0 F5.6 F5.6 Focusing the Viewfinder The camera is equipped with diopter adjustment in the range –4 to +2 m–1 to accommodate individual differences in vision. Rotate the diopter adjustment control until the viewfinder display is in sharp focus.
The DISP/BACK Button The DISP/BACK button controls the display of indicators in the viewfinder and LCD monitor. ■ LCD Monitor: Shooting Full Normal 100 +1 First Steps ■ Viewfinder: Shooting Info display Standard 100 +1 000100 3 2 1 F 0 3 1 2 2 1 3 0 1 2 3 0.1 0.5 P 2000 1.0 F5.6 1.5 2.0 F5.6 3.0 5.0 P 1 10 200 P 2000 F5.6 2000 5.6 F 0.1 0.5 200 P 200 100 1.0 2000 1.5 2.0 F5.6 3.0 5.0 10 200 F 3 2 1 0 1 2 3 0.1 0.5 P 1.0 2000 1.5 2.0 3.0 F5.
The DISP/BACK Button ■ Custom Display To choose items for display in the viewfinder and for the custom (and in manual focus mode, dual) display options in the monitor (P 21): 1 Select DISP. CUSTOM SETTING. Select A SCREEN SET-UP > DISP. CUSTOM SETTING in the setup menu. 2 Choose items. Highlight items and press MENU/OK to select or deselect.
The DISP/BACK Button ■ Viewfinder/LCD Monitor: Playback Information on Information off Favorites 3:2 F 12 / 31 / 2050 3 10 : 00 AM F4.5 -1 2/ 3 12 / 31 / 2050 200 10 : 00 AM Histograms Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the number of pixels by the vertical axis. Shadows Highlights 100-0001 3:2 F ISO 200 1/1000 F4.
Basic Photography and Playback Taking Photographs This section describes how to take pictures using program AE (mode P). For information on S, A, and M modes, see page 46. 1 Adjust settings for program AE. A B C F A Shutter speed (P 46): Select A (auto) B Sensitivity (P 50): Select A (auto) C Drive mode (P 54): Select S (single frame) D Focus mode (P 61): Select S (single AF) E Aperture (P 46): Select A (auto) F Metering (P 53): Select o (multi) Confirm that P appears in the display.
Taking Photographs 2 Ready the camera. 4 Focus. Hold the camera steady with both hands and brace your elbows against your sides. Shaking or unsteady hands can blur your shots. Frame the picture with your subject in the center of the display and press the shutter button halfway to focus. R If the subject is poorly lit, the AF-assist illuminator may light (P 78). If the camera is able to focus, it will beep twice and focus area and focus indicator will glow green.
Viewing Pictures Viewing Pictures Full Frame Pictures can be viewed in the viewfinder or LCD monitor. When taking important pictures, take a test shot and check the results. To view pictures full frame, press a. 100-0001 1 / 1000 F4. F4.5 4.5 2 3 Additional pictures can be viewed by pressing the selector left or right or rotating the front command dial. Press the selector or rotate the dial right to view pictures in the order recorded, left to view pictures in reverse order.
Viewing Pictures Viewing Photo Information The photo information display changes each time the selector is pressed up. 100-0001 3:2 F 12 / 31 / 2050 1 / 1000 10 : 00 AM F4.5 -1 2/ 3 : 100 : STD : STD : STD : STD : STD : OFF FILM SIM. WHITE BALANCE METERING EXPOSURE MODE LENS FOCAL LENGTH : PROVIA : AUTO : PATTERN : PROGRAM : 18.0-55.0mm F2.8-4.0 : 18.
Viewing Pictures Playback Zoom Rotate the rear command dial right to zoom in on the current picture, left to zoom out (to view multiple images, rotate the dial left when the picture is displayed full frame; P 29). When the picture is zoomed in, the selector can be used to view areas of the image not currently visible in the display. Press DISP/BACK or MENU/OK to exit zoom. Zoom indicator Navigation window shows portion of image currently displayed R The maximum zoom ratio varies with image size (P 79).
Viewing Pictures Multi-Frame Playback To change the number of images displayed, rotate the rear command dial left when a picture is displayed full frame. 100-0001 Rotate right to view fewer images. Use the selector to highlight images and press MENU/OK to view the highlighted image full frame (to zoom in on the selected image, rotate the rear command dial right when the picture is displayed full frame; P 28). In the nine- and hundred-frame displays, press the selector up or down to view more pictures.
Deleting Pictures To delete individual pictures, multiple selected pictures, or all pictures, press the b button when a picture is displayed full frame and choose from the options below. Note that deleted pictures can not be recovered. Copy important pictures to a computer or other storage device before proceeding.
Basic Movie Recording and Playback Recording High-Definition (HD) Movies The camera can be used to record short high-definition movies. Sound is recorded in stereo via the built-in microphone; do not cover the microphone during recording. 1 Press the movie-record button to start recording. Recording indicator 12m34s Time remaining R During recording, exposure compensation can be adjusted by up to ±2 EV. R The indicator lamp lights while movies are being recorded.
Recording High-Definition (HD) Movies Using an External Microphone Sound can be recorded with external microphones. See the microphone manual for details; if the microphone jack is 3.5 mm in diameter, use a 3.5-to-2.5 mm adapter. R The dialog shown at right will be displayed when a microphone is connected to the microphone/remote release connector. Press MENU/OK and select MIC/REMOTE RELEASE > m MIC. CHECK MIC/REMOTE RELEASE SETTING SET SKIP 0.1 0.5 1.0 1000 32 1.5 2.0 F3.3 3.0 5.
Viewing Movies During playback, movies are displayed as shown at right. The following operations can be performed while a movie is displayed: 100-0006 Operation Progress is shown in the display during playback. PLAY Progress bar 15s Q Do not cover the speaker during playback. Q Sound is not played back in silent mode. STOP PAUSE Playback Speed Press the selector left or right to adjust playback speed during playback. Speed is shown by the Arrow number of arrows (M or N).
The Q (Quick Menu) Button Press Q for quick access to the following items. For more information on the options available, see the pages listed below. AF MODE BASE 3:2 OFF SET A u SELECT CUSTOM SETTING .......................71 B F AF MODE...................................................78 C U DYNAMIC RANGE .....................................79 D D WHITE BALANCE......................................43 E h NOISE REDUCTION ..................................80 F O IMAGE SIZE .............................
Using the Q Button This section describes the shooting options that can be accessed using the Q button. The Self-Timer Use the timer for self-portraits or to prevent blur caused by camera shake. 1 Highlight B SELF-TIMER in the quick menu (P 34) and rotate the rear command dial to select from the options below. Press the Q button to proceed. Option R Self-timer options can also be accessed from the shooting menu (P 79). 2 Press the shutter button halfway to focus.
Using the Q Button Flash Photography Use shoe-mounted flash units for additional lighting at night or indoors under low light. 1 Remove the hot shoe cover and slide the flash onto the hot shoe as shown, stopping when it clicks into place. Optional Flash Units The camera can be used with optional FUJIFILM shoemounted flash units (P 112). Do not use third-party flash units that apply over 300 V to the camera hot shoe. The Sync Terminal Use the sync terminal to connect flash units that require a sync cable.
Using the Q Button 3 Highlight p FLASH MODE in the quick menu (P 34) and rotate the rear command dial to select from the options below. Press the Q button to proceed. R Flash options can also be accessed from the shooting menu (P 81). Q Depending on the distance to the subject, some lenses may cast shadows in photos taken with the flash. R Turn off or lower the flash where flash photography is prohibited or to capture natural lighting under dim light.
Using the Q Button Intelligent Face Detection Intelligent Face Detection sets focus and exposure for human faces anywhere in the frame, preventing the camera from focusing on the background in group portraits. Choose for shots that emphasize portrait subjects. To use Intelligent Face Detection, highlight b FACE DETECTION in the quick menu (P 35), then rotate the rear command dial until ON is displayed and press the Q button.
The Fn (Function) Buttons The roles played by the six function buttons can be selected in the setup menu FUNCTION (Fn) SETTING Fn1 (P 91) or by pressing and holding the DISP/BACK button and choosing a button Fn2 from the menu shown at right.
Default Roles The following sections describe the default roles assigned to the Fn buttons. Bracketing and Advanced Filters (Fn1) Buttons assigned this role can be used to select bracketing or advanced filter options. R Bracketing and advanced filter options can also be accessed from the shooting menu (P 77).
Default Roles Wireless Options (Fn2) Press the function button in shooting mode to connect to a smartphone or tablet via Wi-Fi (P 97). Once a connection is established, you can control the camera from the phone or download location data. R Wireless options can also be accessed from the shooting and playback menus (P 82, 83). Macro Mode (Fn3) To focus at short distances, press the function button and select ON. To exit macro mode, press the selector up and select OFF.
Default Roles Film Simulation (Fn4) Simulate the effects of different kinds of film, including black-and-white (with or without color filters). Press the function button to display the options shown below, then press the selector up or down to highlight an option and press MENU/OK to select. Option Description c (PROVIA/STANDARD) Standard color reproduction. Suited to a wide range of subjects, from portraits to landscapes. A high-contrast palette of saturated colors, suited to nature photos.
Default Roles White Balance (Fn5) For natural colors, press the function button to display the following options, then use the selector to highlight an option that matches the light source and press MENU/OK. The dialog shown at bottom right will be displayed; use the selector to fine-tune white balance or press DISP/BACK to exit without fine-tuning. WB SHIFT SET R White balance is adjusted for flash lighting only in AUTO and g modes. Turn the flash off using other white balance options.
Default Roles h: Custom White Balance Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will be displayed; frame a white object so that it fills the display and press the shutter button all the way down to measure white balance (to select the most recent custom value and exit without measuring white balance, press DISP/BACK, or press MENU/OK to select the most recent value and display the fine-tuning dialog).
Default Roles Focus-Frame Selection (Fn6) The camera offers a choice of focus points, allowing photographs to be composed with the main subject positioned almost anywhere in the frame. Q In focus modes S and C, focus-area selection is only available when t AREA is selected for G AUTOFOCUS SETTING > AF MODE in the shooting menu and Intelligent Face Detection (P 38) is off.
More on Photography and Playback Choosing an Exposure Mode The camera offers a choice of program AE (P), shutter-priority AE (S), aperture-priority AE (A), and manual exposure (M) modes. Program AE (P) To allow the camera to adjust both shutter speed and aperture for optimal exposure, set shutter speed and aperture to A. P will appear in the display. Q If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show “– – –”.
Choosing an Exposure Mode R At settings other than 180X, shutter speed can also be adjusted in increments of 1/3 EV by rotating the front command dial. Shutter speed can be adjusted even while the shutter button is pressed halfway. Aperture mode switch 3 Q If the correct exposure can not be achieved at the selected shutter speed, aperture will be displayed in red when the shutter button is pressed halfway. Adjust shutter speed until the correct exposure is achieved.
Choosing an Exposure Mode Aperture-Priority AE (A) To adjust aperture manually while letting the camera select shutter speed for optimal exposure, rotate the shutter speed dial to A and adjust aperture as desired. A will appear in the display. R Aperture can be adjusted even while the shutter button is pressed halfway. Q If the correct exposure can not be achieved at the selected aperture, the shutter speed will be displayed in red when the shutter button is pressed halfway.
Choosing an Exposure Mode R At settings other than 180X, shutter speed can also be adjusted in increments Aperture mode switch of 1/3 EV by rotating the front command dial. R The manual exposure display includes an exposure indicator that shows the Exposure indicator amount the picture would be under- or over-exposed at current settings. 3 2 1 0 1 2 3 M 2000 F5.
Sensitivity “Sensitivity” refers to the camera’s sensitivity to light. Sensitivity is adjusted by pressing the dial lock release and rotating the sensitivity dial; choose from values between 200 and 6400, or select L (100), H1 (defaults to 12800), or H2 (defaults to 25600) for special situations.
Sensitivity N ISO AUTO SETTING Option Default DEFAULT SENSITIVITY 200 MAX. SENSITIVITY 800 MIN. SHUTTER SPEED 1/60 R If the value selected for DEFAULT SENSITIVITY is higher than that selected for MAX. SENSITIVITY, DEFAULT SENSITIVITY will be set to the value selected for MAX. SENSITIVITY. R The camera may select shutter speeds slower than MIN. SHUTTER SPEED if pictures would still be underexposed at the value selected for MAX. SENSITIVITY.
Exposure Compensation Rotate the exposure compensation dial to adjust exposure when photographing very bright, very dark, or high-contrast subjects. The effect is visible in the display. Exposure compensation indicator 100 +1 3 2 1 0 1 2 3 P 2000 F5.6 0.1 0.5 200 LCD monitor P 2000 1.0 1.5 2.0 3.0 5.0 F5.
Metering Mode o (MULTI) Description The camera instantly determines exposure based on an analysis of composition, color, and brightness distribution. Recommended in most situations. The camera meters lighting conditions in an area at the center of the frame equivalent to 2% of the total. Recommended with backlit subjects and in other p (SPOT) cases in which the background is much brighter or darker than the main subject. Exposure is set to the average for the entire frame.
The DRIVE Dial The DRIVE dial gives you access to the following options. Option BKT CH CL S j ADV. u Description Bracketing: Automatically vary settings over a series of pictures (P 54). High-speed burst: Shoot photos in high-speed bursts (P 56). Low-speed burst: Shoot in low-speed bursts (P 56). Single frame: Take photos one at a time. Multiple exposure: Create photos that combine two exposures (P 57). Advanced filter: Take photos with filter effects (P 58).
The DRIVE Dial program selection is assigned to the Fn1 button) or the shooting menu (P 77). Option Description Select a bracketing amount. Each time the shutter button is pressed, the camera will take three shots: one using the metered value for exposure, the second overexposed by the selected amount, and the third AE BKT underexposed by the same amount (regardless of the amount selected, exposure will not exceed the limits of the exposure metering system). Select a bracketing amount.
The DRIVE Dial Continuous Shooting (Burst Mode) Capture motion in a series of pictures. 1 Rotate the DRIVE dial to select CH (high-speed burst) or CL (low-speed burst). R Additional time may be required to record pictures when shooting ends. R If file numbering reaches 999 before shooting is complete, the remaining pictures will be recorded to a new folder (P 93). R In some drive modes, shooting may not begin if the space available on the memory card is insufficient.
The DRIVE Dial + 1 Rotate the DRIVE dial to j. 4 Take the second shot, using the first frame as a guide. 5 Press MENU/OK to create the multiple exposure, or press the selector left to return to Step 4 and retake the second shot. More on Photography and Playback Multiple Exposures Create a photograph that combines two exposures. 2 Take the first shot. 3 Press MENU/OK. The first shot will be shown superimposed on the view through the lens and you will be prompted to take the second shot.
The DRIVE Dial Advanced Filters Take photos with filter effects. 1 Rotate the DRIVE Filter dial to ADV.. K DYNAMIC TONE X SOFT FOCUS 2 Select one of the following options using a function button (P 40; at default settings, filter selection is assigned to the Fn1 button) or the shooting menu (P 77). Filter G TOY CAMERA H MINIATURE I POP COLOR J HIGH-KEY Z LOW-KEY 58 Description Choose for a retro toy camera effect. The tops and bottoms of pictures are blurred for a diorama effect.
The DRIVE Dial 1 Rotate the DRIVE dial to u. 2 To select the size of the angle through which you will pan the camera while shooting, press the selector left. Highlight a size and press MENU/OK. 3 Press the selector right to view a choice of pan directions. Highlight a pan direction and press MENU/OK. 4 Press the shutter button all the way down to start recording. There is no need to keep the shutter button pressed during recording. 5 Pan the camera in the direction shown by the arrow.
The DRIVE Dial Q Panoramas are created from multiple frames; exposure for the entire panorama is determined by the first frame. The camera may in some cases record an greater or lesser angle than selected or be unable to stitch the frames together perfectly. The last part of the panorama may not be recorded if shooting ends before the panorama is complete. Q Shooting may be interrupted if the camera is panned too quickly or too slowly.
Focus Mode 3 2 More on Photography and Playback Use the focus mode selector to choose how the camera focuses (note that regardless of the option selected, manual focus will be used when the lens is in manual focus mode). • S (single AF): Focus locks while the shutter button is pressed halfway. Choose for stationary subjects. • C (continuous AF): Focus is continually adjusted to reflect changes in the distance to the subject while the shutter button is pressed halfway. Use for subjects that are in motion.
Focus Mode ■ The Focus Indicator The focus indicator turns green when the subject is in focus and blinks white when the camera is unable to focus. Brackets (“( )”) indicate that the camera is focusing and are displayed continuously in mode C. j is displayed in manual focus mode. 3 2 1 0 1 2 3 P 1000 F3.3 400 Focus indicator Checking Focus To zoom in on the current focus area (P 45) for precise focus, press the FOCUS ASSIST button. Press the button again to cancel zoom.
Focus Mode R The c MF ASSIST menu can be displayed by pressing and holding the FOCUS ASSIST button. The following options are available: • FOCUS PEAK HIGHLIGHT: Highlights high-contrast outlines. Rotate the focus ring until the subject is highlighted. • DIGITAL SPLIT IMAGE: Displays a split, black-and-white image in the center of the frame. Frame the subject in the split-image area and rotate the focus ring until the three parts of the split image are correctly aligned.
Long Time-Exposures (T/B) Select a shutter speed of T (time) or B (bulb) for long time-exposures. R Use of a tripod is recommended to prevent the camera from moving during the exposure. R To reduce “noise” (mottling) in long time-exposures, select ON for K LONG EXPOSURE NR in the shooting menu (P 80). Note that this may increase the time needed to record images after shooting. Time (T) 1 Rotate the shutter speed dial to T. Bulb (B) 1 Rotate the shutter speed dial to B.
Long Time-Exposures (T/B) 1 Press MENU/OK in shooting mode to display the shooting menu. Press the selector up or down to highlight o INTERVAL TIMER SHOOTING and press MENU/OK. 2 Use the selector to choose the interval and number of shots. Press MENU/OK to proceed. INTERVAL/NUMBER OF TIMES INTERVAL NUMBER OF TIMES 24 23 22h59m59s 997 21 20 END 3 Use the selector to choose the starting time and then press MENU/OK. Shooting will start automatically.
Long Time-Exposures (T/B) Using a Remote Release An optional RR-90 remote release can be used for long time-exposures. See the manual provided with the RR-90 for more information. 66 Third-Party Remote Releases Electronic releases from thirdparty suppliers can be connected via the microphone/remote release connector. A confirmation dialog will be displayed when a third-party release is connected; press MENU/OK and select n REMOTE for MIC/REMOTE RELEASE. CHECK MIC/REMOTE RELEASE SETTING SET SKIP 0.1 0.
Focus/Exposure Lock 1 Focus: Position the subject in the focus frame and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while the shutter button is pressed halfway (AF/AE lock). P 2000 F5.6 200 R Focus and exposure can also be locked with the AF-L and AE-L buttons, respectively (if AE/AF LOCK is selected for d AF-LOCK MODE in the shooting menu, pressing the AF-L button will lock both focus and exposure; P 76).
Focus/Exposure Lock Autofocus Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed below. • Very shiny subjects such as mirrors or car bodies. • Fast-moving subjects. • • • • Subjects photographed through a window or other reflective object. Dark subjects and subjects that absorb rather than reflect light, such as hair or fur. Insubstantial subjects, such as smoke or flame.
Recording Pictures in RAW Format 1 Press MENU/OK in shooting mode to display the shooting menu. Press the selector up or down to highlight T IMAGE QUALITY and press MENU/OK. 2 Highlight an option and press MENU/OK. Select RAW to record only RAW images, or FINE+RAW or NORMAL+RAW to record both JPEG copy together with the RAW images.
Recording Pictures in RAW Format Creating JPEG Copies of RAW Pictures RAW pictures store information on camera settings separately from the data captured by the camera image sensor. Using the j RAW CONVERSION option in the playback menu, you can create JPEG copies of RAW pictures using different options for the settings listed below. The original image data are unaffected, allowing a single RAW image to be processed in a multitude of different ways.
Saving Settings 1 Press MENU/OK in shooting mode to display the shooting menu. Press O MENU P SHOOTING CUSTOM 1 CUSTOM 2 CUSTOM 3 CUSTOM 4 CUSTOM 5 EDIT/SAVE CUSTOM SETTING 35mm CUSTOM 6 OFF 50mm CUSTOM 7 OFF 0 ON ON the selector up or down to highlight K EDIT/SAVE CUSTOM SETTING and press MENU/OK. 2 Highlight a custom settings bank and press MENU/OK to select.
Using a Mount Adapter When M-mount lenses are attached using an optional FUJIFILM M MOUNT ADAPTER, the camera processes pictures as they are taken to maintain image quality and correct for a variety of effects. R Attaching a mount adapter enables m SHOOT WITHOUT LENS (P 81) and hides the distance indicator in the standard display. R Before checking focus, set the focus mode selector to M (P 61).
Using a Mount Adapter NEXT SET To use color shading correction, follow the steps below. 1 Rotate the rear command dial to choose a corner. The selected corner is indicated by a triangle. 2 Use the selector to adjust shading until there is no visible difference in color between the selected corner and the center of the image. Press the selector left or right to adjust colors on the cyan–red axis, up or down to adjust colors on the blue– yellow axis.
Image Search Follow the steps below to search for pictures. 1 Press MENU/OK during playback to display the playback menu. Press the selector up or down to highlight b IMAGE SEARCH and press MENU/OK. 2 Highlight an option and press MENU/OK. Option BY DATE BY FACE BY I FAVORITES BY TYPE OF DATA BY UPLOAD MARK Description Search by date. Search for pictures that include faces. Search by rating (P 26). Find all still pictures, all movies, or all RAW pictures.
PhotoBook Assist Creating a PhotoBook 1 Select NEW BOOK for m PHOTOBOOK ASSIST in the playback menu (P 85) and choose from the following options: • SELECT FROM ALL: Choose from all available pictures. • SELECT BY IMAGE SEARCH: Choose from pictures matching selected search conditions (P 74). R Neither photographs a or smaller nor movies can be selected for photobooks.
PhotoBook Assist Viewing Photobooks Highlight a book in the photobook assist menu and press MENU/OK to display the book, then press the selector left or right to scroll through the pictures. Editing and Deleting Photobooks Display the photobook and press MENU/OK. The following options will be displayed; select the desired option and follow the on-screen instructions. • EDIT: Edit the book as described in “Creating a PhotoBook” (P 75). • ERASE: Delete the book.
Menus Using the Menus: Shooting Mode The shooting menu is used to adjust settings for a wide range of shooting conditions. To display the shooting menu, press MENU/OK in shooting mode. Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete. P SHOOTING MENU BKT/Adv.
Using the Menus: Shooting Mode G AUTOFOCUS SETTING Adjust autofocus settings. Option FOCUS AREA MACRO RELEASE/FOCUS PRIORITY INSTANT AF SETTING AF MODE FACE DETECTION PRE-AF Description Choose the focus area (P 45). Turn macro mode on or off (P 41). Choose how the camera focuses in focus mode AF-S or AF-C. • RELEASE: Shutter response is prioritized over focus. Pictures can be taken when the camera is not in focus. • FOCUS: Focus is prioritized over shutter response.
Using the Menus: Shooting Mode O IMAGE SIZE Choose the size and aspect ratio at which still pictures are recorded. Option O 3:2 Aspect Ratio Pictures with an aspect ratio of 3 : 2 have the same proportions as O 16 : 9 a frame of 35 mm film, while an aspect ratio of 16 : 9 is suited to O 1 : 1 display on High Definition (HD) devices. Pictures with an aspect P 3 : 2 ratio of 1 : 1 are square. P 16 : 9 O IMAGE SIZE is not reset when the camera is turned off or an- P 1 : 1 other shooting mode is selected.
Using the Menus: Shooting Mode o INTERVAL TIMER SHOOTING Adjust settings for interval timer photography (P 65). D WHITE BALANCE Adjust colors to match the light source (P 43). f COLOR Adjust color density. q SHARPNESS Sharpen or soften outlines. r HIGHLIGHT TONE Adjust the appearance of highlights. s SHADOW TONE Adjust the appearance of shadows. h NOISE REDUCTION Reduce noise in pictures taken at high sensitivities. K LONG EXPOSURE NR Select ON to reduce mottling in long time-exposures (P 64).
Using the Menus: Shooting Mode l MOUNT ADAPTOR SETTING Adjust settings for M-mount lenses connected using an optional FUJIFILM M MOUNT ADAPTER (P 72). m SHOOT WITHOUT LENS Choose whether shutter release is enabled when no lens is attached. c MF ASSIST Choose how focus is displayed in manual focus mode (P 63). • STANDARD: Focus is displayed normally (focus peaking and digital split image are not available). • DIGITAL SPLIT IMAGE: A black-and-white split-image display.
Using the Menus: Shooting Mode W MOVIE SET-UP Adjust movie settings (P 31). Option Description Select a frame size for movie recording. • i 1920×1080 60 fps: Full HD (60 fps) MOVIE MODE • i 1920×1080 30 fps: Full HD (30 fps) • h 1280×720 60 fps: HD (60 fps) • h 1280×720 30 fps: HD (30 fps) MIC LEVEL ADJUSTMENT Adjust the microphone recording level. Specify whether the device connected to the microphone/remote release connector is a microphone or MIC/REMOTE RELEASE a remote release (P 32, 66).
Using the Menus: Playback Mode To display the playback menu, press MENU/OK in playback mode. Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings are complete. PLAYBACK MENU WIRELESS COMMUNICATION RAW CONVERSION ERASE CROP RESIZE PROTECT IMAGE ROTATE EXIT Playback Menu Options r WIRELESS COMMUNICATION Connect to a smartphone or tablet over a wireless network (P 97).
Using the Menus: Playback Mode e RESIZE Create a cropped copy of the current picture. 1 Display the desired picture. 2 Select e RESIZE in the playback menu. 3 Highlight a size and press MENU/OK to display a confirmation dialog. 4 Press MENU/OK again to save the resized copy to a separate file. R The sizes available vary with the size of the original image. D PROTECT Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK. • FRAME: Protect selected pictures.
Using the Menus: Playback Mode B RED EYE REMOVAL Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create a copy with reduced red-eye. 1 Display the desired picture. 2 Select B RED EYE REMOVAL in the playback menu. 3 Press MENU/OK. R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on the scene.
Using the Menus: Playback Mode j MARK FOR UPLOAD TO Select pictures for upload to YouTube, Facebook or MyFinePix.com using MyFinePix Studio (Windows only). 1 Select YouTube to choose movies for upload to YouTube, Facebook to choose photos and movies for upload to Facebook, or MyFinePix.com to choose photos for upload to MyFinePix.com. 2 Press the selector left or right to display pictures and press MENU/OK to select or deselect. Press DISP/BACK to exit when all the desired pictures are selected.
Using the Menus: Playback Mode J DISP ASPECT Choose how High Definition (HD) devices display pictures with an aspect ratio of 3 : 2 (this option is available only when an HDMI cable is connected). Select 16 : 9 to display the image so that it fills the screen with its top and bottom cropped out, 3 : 2 to display the entire image with black bands at either side.
The Setup Menu Using the Setup Menu 1 Display the setup menu. 1.1 Press MENU/OK to display the menu for the current mode. 1.2 Press the selector left to highlight the tab for the current menu. 1.3 Press the selector down to highlight the setup menu tab containing the desired option. SET-UP DATE/TIME TIME DIFFERENCE ENGLISH RESET SILENT MODE SOUND SET-UP SCREEN SET-UP OFF EXIT Tab 1.4 Press the selector right to place the cursor in the setup menu. 2 Adjust settings.
The Setup Menu Setup Menu Options F DATE/TIME Set the camera clock (P 18). N TIME DIFFERENCE Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between local time and your home time zone: 1 Highlight g LOCAL and press MENU/OK. 2 Use the selector to choose the time difference between local time and your home time zone. Press MENU/OK when settings are complete.
The Setup Menu b SOUND SET-UP Adjust sound settings. Option OPERATION VOL. PLAYBACK VOLUME Description Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF (mute) to disable control sounds. Adjust the volume for movie playback. A SCREEN SET-UP Adjust display settings. Option Description Choose how long images are displayed after shooting. Colors may differ slightly from those in the final image and “noise” mottling may be visible at high sensitivities.
The Setup Menu A SCREEN SET-UP (Continued) Option Description Choose the type of framing grid available in shooting mode. F GRID 9 G GRID 24 H HD FRAMING A six-by-four grid. Frame HD pictures in the crop shown by the lines at the top and bottom of the display. FRAMING GUIDELINE P For “rule of thirds” composition. FOCUS CHECK FOCUS SCALE UNITS DISP. CUSTOM SETTING P Choose ON to automatically rotate “tall” (portrait-orientation) pictures during playback. Choose a color scheme.
The Setup Menu Z POWER MANAGEMENT Adjust power management settings. Option AUTO POWER OFF HIGH PERFORMANCE Description Choose the length of time before the camera turns off automatically when no operations are performed. Shorter times increase battery life; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera turns off automatically even when OFF is selected.
The Setup Menu t SAVE DATA SET-UP Adjust file management settings. Option FRAME NO. Description New pictures are stored in image files named using a four-digit file number assigned by Frame number adding one to the last file number used. The file number is displayed during playback as 100-0001 shown at right. FRAME NO. controls whether file numbering is reset to 0001 when a new memory card is inserted or the current memory card is formatted.
The Setup Menu r WIRELESS SETTINGS Adjust settings for connection to wireless networks. Option GENERAL SETTINGS RESIZE IMAGE FOR SMARTPHONE H PC AUTO SAVE SETTINGS Description Choose a name (NAME) to identify the camera on the wireless network (the camera is assigned a unique name by default) or select RESET WIRELESS SETTINGS to restore default settings.
Factory Defaults The factory default settings for the options in the shooting and setup menus are listed below. These settings can be restored using the R RESET option in the setup menu (P 89). ■ Shooting Menu Menu k BKT/Adv. SETTING BKT SELECT Adv.
Factory Defaults ■ Setup Menu Menu o SILENT MODE b SOUND SET-UP OPERATION VOL. PLAYBACK VOLUME A SCREEN SET-UP IMAGE DISP. EVF AUTOROTATE DISPLAYS PREVIEW EXP. IN MANUAL MODE EVF/LCD BRIGHTNESS FRAMING GUIDELINE AUTOROTATE PB FOCUS CHECK FOCUS SCALE UNITS DISP.
Connections Wireless Transfer Access wireless networks and connect to computers, smartphones, or tablets. For downloads and other information, visit http://fujifilm-dsc.com/wifi/. Wireless Connections: Smartphones Install the “FUJIFILM Camera Remote” app on your smartphone to browse the images on the camera, download selected images, control the camera remotely, or copy location data to the camera. To connect to the smartphone, press the camera Wi-Fi button in playback mode.
Viewing Pictures on a Computer The supplied software can be used to copy pictures to a computer, where they can be stored, viewed, organized, and printed. Before proceeding, install the software as described below. Do NOT connect the camera to the computer until installation is complete.
Viewing Pictures on a Computer 3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive. Windows 8/Windows 7/Windows Vista If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed; click Yes (Windows 8/Windows 7) or Allow (Windows Vista). The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio and RAW FILE CONVERTER.
Viewing Pictures on a Computer Macintosh: Installing RAW FILE CONVERTER RAW FILE CONVERTER is used to view RAW images on your computer. 1 Confirm that the computer meets the following system requirements: CPU OS RAM Free disk space Video Intel (Core 2 Duo or better) Pre-installed copies of Mac OS X version 10.6–10.9 (visit http://www.fujifilm.com/support/digital_cameras/ compatibility/ for more information).
Viewing Pictures on a Computer Connecting the Camera 1 Find a memory card containing pictures you want to copy to the computer and insert the card into the camera (P 14). R Windows users may require the Windows CD when starting the software for the first time. Q Loss of power during transfer could result in loss of data or damage to the memory card. Insert a fresh or fully-charged battery before connecting the camera.
Viewing Pictures on a Computer Q If a memory card containing a large number of images is inserted, there may be a delay before the software starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Printing Pictures via USB If the printer supports PictBridge, the camera can be connected directly to the printer and pictures can be printed without first being copied to a computer. Note that depending on the printer, not all the functions described below may be supported. Connecting the Camera 1 Connect a USB cable (available separately from third-party suppliers) as shown and turn the printer on. Printing Selected Pictures 1 Press the selector left or right to display a picture you wish to print.
Printing Pictures via USB Printing the Date of Recording To print the date of recording on pictures, press DISP/BACK in the PictBridge display and select PRINT WITH DATE s (to print pictures without the date of recording, select PRINT WITHOUT DATE). To ensure that the date is correct, set the camera clock before taking pictures. Some printers do not support date printing. See the printer manual for details.
Printing Pictures via USB During Printing The message shown at right is displayed during printing. Press DISP/BACK to cancel before all pictures are printed (depending on the printer, printing may end before the current picture has printed). PRINTING Creating a DPOF Print Order The K PRINT ORDER (DPOF) option in the playback menu can be used to create a digital “print order” for PictBridge-compatible printers or devices that support DPOF.
Printing Pictures via USB ■ WITH DATE s/ WITHOUT DATE To modify the DPOF print order, select K PRINT ORDER (DPOF) in the playback menu and press the selector up or down to highlight WITH DATE s or WITHOUT DATE. 3 Repeat steps 1–2 to complete the WITH DATE s: Print date of recording on pictures.
Printing Pictures via USB ■ RESET ALL To cancel the current print order, select RESET ALL for K PRINT ORDER (DPOF). The confirmation shown at right will be displayed; press MENU/OK to remove all pictures from the order. RESET DPOF OK? YES CANCEL R Print orders can contain a maximum of 999 pictures. RESET DPOF OK? R If a memory card is inserted containing a print order created by another camera, the message shown at right will YES NO be displayed.
Viewing Pictures on TV To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately from third-party suppliers; note that the TV can only be used for playback, not shooting). 1 Turn the camera off. 2 Connect the cable as shown below. Insert into HDMI connector Insert into HDMI mini connector Q Use an HDMI cable no more than 1.5 m (4.9 ft.) long. R Be sure the connectors are fully inserted. 3 Tune the television to the HDMI input channel.
Technical Notes Optional Accessories The camera supports a wide range of accessories from FUJIFILM and other manufacturers. Accessories from FUJIFILM The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/ products/digital_cameras/index.html.
Optional Accessories FUJINON lenses XF-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount. XC-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount. Shoe-mounted flash units EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide Number of 20/65 (ISO 100, m/ft.) and supports TTL flash control. The flash head can be rotated upwards 90° for bounce lighting.
Optional Accessories Front lens caps FLCP-39/FLCP-52/FLCP-58/FLCP-62/FLCP-72: Protect the front lens element when the lens is not in use. Rear lens caps RLCP-001: Protect the rear lens element when the lens is not attached to the camera. Body caps BCP-001: Cover the camera lens mount when no lens is attached. Battery grips VG-XT1: This grip accommodates an extra battery for improved endurance and makes it easier to hold the camera rotated 90 ° to frame pictures in “tall” (portrait) orientation.
Optional Accessories Connecting the Camera to Other Devices ■ Remote Shutter Releases ■ External Microphones X-T1 MIC-ST1 stereo microphone * ■ Flash Photography RR-90 remote release * ■ Printing USB cable † ■ Battery Grips PictBridgecompatible printer † Printer † ■ Computer Related EF-20 shoeEF-42 shoeEF-X20 shoemounted flash * mounted flash * mounted flash * ■ Lenses VG-XT1 vertical battery grip * SD/SDHC/SDXC memory card † XF-series lenses * ■ M Mount Adapters USB cable † Computer † * Availab
The Vertical Battery Grip The optional VG-XT1 vertical battery grip accommodates an extra battery for improved endurance and makes it easier to hold the camera rotated 90 ° to frame pictures in “tall” (portrait) orientation. Parts of the VG-XT1 The shooting controls on the VG-XT1 perform the same functions as the controls on the camera.
The Vertical Battery Grip Attaching the VG-XT1 The VG-XT1 attaches as shown below. 1 Remove the vertical battery grip connector cover from the camera and place it in the grip connector cover compartment. 2 Align the connectors on the grip with the matching connectors on the camera. 3 Rotate the lock screw knob to tighten the lock screw. Inserting a Battery Insert a battery as shown below. 1 Unlatch and open the battery-chamber cover. 2 Insert the battery. 3 Close and latch the batterychamber cover.
Caring for the Camera To ensure continued enjoyment of the product, observe the following precautions. ■ Water and Sand This camera cannot be used under water. Keep the camera against penetration of garbage, mud, sand, dust, water, harmful gas, salt, and so on. Do not place the camera on a wet surface. Make sure the covers (caps) for the battery, card slot and ports are securely closed before use. If the camera is exposed to rain, droplets of water, and so on, dry it thoroughly.
Cleaning the Image Sensor Multiple photographs marred by spots or blotches in identical locations may indicate the presence of dust on the camera image sensor. Clean the sensor using the V SENSOR CLEANING option in the setup menu (P 92); if the problem persists, you can clean the sensor manually as described below. Note that there will be a charge to repair or replace the image sensor if it is damaged during cleaning. 1 Use a blower (not a brush) to remove dust from the sensor.
Troubleshooting Problems and Solutions ■ Power and Battery Problem The camera does not turn on. The monitor does not turn on. The battery runs down quickly. The battery is exhausted exhausted:: Charge the battery ((P P 13) or insert a fully-charged spare battery ((P P 14). Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P P 13). Charge the battery at room temperature ((P P iv).
Problems and Solutions ■ Shooting Problem No picture is taken when the shutter button is pressed. • • • • • • • Solution The memory card is full full:: Insert a new memory card or delete pictures (P (P 14, 30). The memory card is not formatted formatted:: Format the memory card (P (P 94). There is dirt on the memory card contacts contacts:: Clean the contacts with a soft, dry cloth. The memory card is damaged damaged:: Insert a new memory card ((P P 14).
Problems and Solutions Problem The flash does not fire. • • • • • • Solution The flash can not be used at current settings settings:: See the list of the settings that can be used with the flash. The flash is lowered lowered:: Raise the flash (P (P 36). The DRIVE dial is rotated to BKT, CH, or CL CL:: Rotate the dial to S ((P P 54, 56). The battery is exhausted exhausted:: Charge the battery ((P P 13) or insert a fully-charged spare battery ((P P 14).
Problems and Solutions ■ Playback Problem Solution Pictures are grainy. The pictures were taken with a different make or model of camera. Playback zoom is unavailThe pictures were created using O RESIZE or with a different make or model of camera. able. • Playback volume is too low: low: Adjust playback volume (P (P 90). No sound in movie • The microphone was obstructed obstructed:: Hold the camera correctly during recording ((P P 2, 31). playback.
Problems and Solutions Problem Solution • The camera is not properly connected: connected: Connect the camera properly (P (P 108).). Note that once the camera is connected, pictures will be displayed on the TV instead of in the camera monitor. No picture or sound on TV. • Input on the television is set to “TV”: “TV”: Set input to “HDMI”. • The volume on the TV is too low: low: Use the controls on the television to adjust the volume.
Warning Messages and Displays The following warnings appear in the display. Warning B (red) A (blinks red) k s (displayed in red with red focus frame) Aperture or shutter speed displayed in red FOCUS ERROR TURN OFF THE CAMERA AND TURN ON AGAIN LENS CONTROL ERROR LENS ERROR BUSY CARD NOT INITIALIZED PROTECTED CARD 122 Description Low battery. Charge the battery ((P P 13) or insert a fully-charged spare battery ((P P 14). Battery exhausted.
Warning Messages and Display Warning CARD ERROR b MEMORY FULL NO CARD WRITE ERROR READ ERROR TOO MANY FRAMES Troubleshooting FRAME NO. FULL Description • The memory card is not formatted for use in the camera camera:: Format the card (P (P 94). • The memory card contacts require cleaning or the memory card is damaged damaged:: Clean the contacts with a soft, dry cloth. If the message is repeated, format the card (P (P 94). If the message persists, replace the card.
Warning Messages and Display Warning PROTECTED FRAME CAN NOT CROP m CANNOT EXECUTE F CANNOT EXECUTE CAN NOT ROTATE F CAN NOT ROTATE Description An attempt was made to delete or rotate to a protected picture. Remove protection and try again ((P P 84). The picture is damaged or was not created with the camera. Red-eye removal can not be applied to pictures created with other devices. Red-eye removal can not be applied to movies. The selected picture can not be rotated. Movies can not be rotated.
Appendix Memory Card Capacity The following table shows the recording time or number of pictures available at different image sizes. All figures are approximate; file size varies with the scene recorded, producing wide variations in the number of files that can be stored. The number of exposures or length remaining may not diminish at an even rate. 4 GB Capacity O T FINE 600 O3:2 Photographs RAW 120 i 1920×1080 60 fps 2 13 min. i 1920×1080 30 fps 2 Movies 1 3 h 1280×720 60 fps 25 min.
Specifications System Model Effective pixels Image sensor Storage media File system File format Image size Lens mount Sensitivity Metering Exposure control Exposure compensation Shutter speed (mechanical shutter) 126 FUJIFILM X-T1 digital camera 16.3 million 23.6 mm × 15.6 mm (APS-C), X-Trans CMOS II sensor with square pixels and primary color filter FUJIFILM-recommended SD/SDHC/SDXC memory cards Compliant with Design Rule for Camera File System (DCF) (DCF),, Exif 2.
Specifications System Continuous Mode I Focus White balance Self-timer Flash mode Hot shoe Viewfinder Frame rate (fps) 8.0 3.0 Frames per burst Up to approximately 47 Until card is full R The frame rate and number of frames per burst may vary depending on the type of memory card used. R The frame rate varies with shooting conditions and the number of images recorded.
Specifications Input/output terminals HDMI output HDMI mini connector Digital input/output USB 2.0 High-Speed Microphone/ φ2.5 mm mini-stereo jack remote release connector Power supply/other Power supply Battery life (approximate number of frames that can be taken with a fully-charged battery, XF 35 mm f/1.
Specifications EF-X8 shoe-mounted flash unit Guide number GN8 (ISO100), GN11 (ISO200) Dimensions (W × H × D) 39.7 mm × 24.2 mm × 63.4 mm/1.5 in. × 0.9 in. × 2.4 in., excluding projections Weight Approx. 41 g/1.4 oz. NP-W126 rechargeable battery Nominal voltage 7.2 V DC Nominal capacity 1,260 mAh Operating temperature 0 °C to +40 °C/+32 °F to +104 °F Dimensions (W × H × D) 36.4 mm × 47.1 mm × 15.7 mm/1.4 in. × 1.8 in. × 0.6 in. Weight Approx. 47 g/1.7 oz.
Specifications ■ Notices • Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/ digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual. • Although the viewfinder and LCD monitor are manufactured using advanced high-precision technology, small bright points and anomalous colors may appear, particularly in the vicinity of text.
Restrictions on Camera Settings The options available in each shooting mode are listed below. Option Focus mode (selector) S C M Exposure compensation (dial) ISO (dial) Photometry (dial) H1/H2 1000 — 6400 200 — 800 L (100) AUTO o p q P S A M BKT CH/CL ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔2 ✔2 ✔ ✔2 ✔2 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔2 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ DRIVE dial j ADV.
Restrictions on Camera Settings Option G AUTOFOCUS SETTING A M BKT CH/CL ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ s ✔ ✔ ✔ ✔ ✔ ✔ ✔ t ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔ ✔ ✔ ✔2 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔6 ✔6 ✔ FACE DETECTION PRE-AF AF ILLUMINATOR O IMAGE SIZE T IMAGE QUALITY U DYNAMIC RANGE P FILM SIMU
Restrictions on Camera Settings Option f COLOR q SHARPNESS r HIGHLIGHT TONE s SHADOW TONE h NOISE REDUCTION K LONG EXPOSURE NR j LENS MODULATION OPTIMIZER u SELECT CUSTOM SETTING K EDIT/SAVE CUSTOM SETTING c MF ASSIST STANDARD DIGITAL SPLIT IMAGE FOCUS PEAK HIGHLIGHT v AE/AF-LOCK MODE d AF-LOCK MODE p FLASH MODE I FLASH COMPENSATION B RED EYE REMOVAL Q/K N/L F/M l/d D P P S A M BKT CH/CL ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Restrictions on Camera Settings Option IMAGE DISP. PREVIEW EXP. IN MANUAL MODE FOCUS CHECK FOCUS SCALE UNITS A SCREEN SET-UP DISP. CUSTOM SETTING FRAMING GUIDELINE ELECTRONIC LEVEL AF DISTANCE INDICATOR MF DISTANCE INDICATOR HISTOGRAM APERTURE/S-SPEED/ISO EXP. COMPENSATION PHOTOMETRY FLASH WHITE BALANCE FILM SIMULATION DYNAMIC RANGE FRAMES REMAINING BATTERY LEVEL IMAGE SIZE/QUALITY J COLOR SPACE 1 2 3 4 134 Not available (grayed out). Changes have no effect. Center focus area selected automatically.
Memo 135
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN http://www.fujifilm.com/products/digital_cameras/index.
