Getting Ready Printing Advanced Printing en: The owner’s manual in English and French is available at “http://home.fujifilm. com/products/dmp.” fr: Le manuel d’utilisation en Anglais et en Français est disponible sur le site “http://home.fujifilm.com/products/dmp.
Features The MP-300 Mobile Printer is a compact portable printer you can take with you anywhere, making it easy for you to print out photos from your digital camera or camera phone. 1. You can print from your digital camera or camera phone anywhere you are. Images from a digital camera or a camera phone can be printed directly without using a computer. Small enough to carry anywhere. PictBridge-compatible (P.28) Easy to print from a PictBridge-compatible digital camera or camera phone using a USB cable.
Contents zInfrared communication / PictBridge Quick Start Guide - PictBridge - . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 zContents of package zPrinter care / Using USB interface / Using the AC power adapter / Photo pack and print care Notes on Handling Films and Finished Prints . . . . . . . . . . . . . . . 16 zFinishing prints / Caution Restrictions . . . . . . . . . . . . . . . . . . . . . .
Quick Start Guide - Infrared communication - Quick Start Guide - PictBridge - 1 Loading the batteries. 2 Loading the photo pack. 1 Loading the batteries. 2 Loading the photo pack. (P.21) (P.22) (P.21) (P.22) 3 Turning on the power. Turquoise mark inside the printer Turquoise mark inside the printer Turquoise mark on the photo pack Turquoise mark on the photo pack 4 Send the image. (P.24) Lit the printer to the 3 Connect digital camera . (P.28) c 4 Turning on the power. Lit 20cm (7.9 in.
Introduction About IrSimple™ ■ What is IrSimple™? Contents of package 1, Lithium Batteries (CR2) 2, Owner’s Manualc 3, Mobile Printer MP-300 (P.18) Getting Ready Printing Advanced Printing Error The owner’s manual en: The owner’s manual in English and French is available at “http://home.fujifilm. com/products/dmp.” fr: Le manuel d’utilisation en Anglais et en Français est disponible sur le site “http://home.fujifilm.com/products/dmp.
Safety Precautions This product has been made to be as safe as possible. This product will provide long, safe service when handled correctly. It is important that this product is handled properly and used only to print pictures. For your ease and safety, please follow what is written in this manual. It is also a good idea to keep this manual in a safe, easy to find place where you can refer to it if needed. Faults of this nature could cause the printer to explode or catch fire and cause burns.
Handling & Care Safety Precautions X Z Never attempt to take this product apart. If this product is dropped or damaged so that the inside is showing, do not touch it. You may be injured. Do not touch any projecting parts inside the photo pack door. C Never get this product wet or handle it with wet hands. Z V 12 2. 3. 4. 5. 6. You may be injured. 7. Doing so may result in an electric shock. Do not mix new and old batteries or batteries of different types.
Handling & Care ■ Using USB interface ■ Photo pack and print care 1. 2. 1. Use the USB cable suitable for the digital camera or camera phone. Ensure that the USB cable is no more than 3 meters (9.8 ft.) long. ■ Using the AC power adapter Use the FUJIFILM AC Power Adapter AC-5VX (sold separately). The use of an AC Power Adapter other than AC-5VX may result in damage to your printer. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Use the AC power adapter indoors only.
Notes on Handling Films and Finished Prints ■ Finishing prints Restrictions 1. zWhile the printer can be used at temperatures between 5˚C and 40˚C (+41 ˚F and +104˚F), to get the best possible print quality it should be used at temperatures between 15˚C and 30˚C (+59˚F and +86˚F). zIn cold conditions, quickly place the print in a warm place such as a roomy jacket pocket for around 30 seconds to warm up the image.
Necessary Items Optional AC Power Adapter The AC power adapter AC-5VX (sold separately) (P.14) Two CR2 lithium batteries ! All batteries must be new and be the same ● The AC power adapter AC-5VX size and type. Use following five manufacturers. 1. FUJIFILM 2. PANASONIC 3. SANYO 4. DURACELL 5. Energizer x Recommended for use when sending images from a digital camera via USB cable. CAUTION Risk of explosion if battery is replaced by an incorrect type.
Part Names Getting Ready to Print 1 Open the battery cover. DC IN 5V socket DATE button (P.39) SHARPEN button (P.38) USB socket Getting Ready Loading the batteries PictBridge lamp DATE lamp ERROR lamp (P.41) 2 Loading the batteries. SHARPEN lamp REPRINT button (P.36) Match the = and - on the batteries to the markings in the battery case. Insert the batteries - end first. Infrared port Film counter POWER button Low Battery lamp (P.42) Battery cover Photo pack door 3 Close the battery cover.
Getting Ready to Print 1 2 Photo pack confirmation window 1 This window allows you to check whether there is a photo pack loaded into the printer. Open the photo pack door. While holding down button 1, slide knob 2 in the direction of the arrow. Photo pack loaded Getting Ready Loading the photo pack No photo pack Turquoise mark inside the printer Turquoise mark on the photo pack 2 Loading the photo pack. Hold the pack by the sides and drop it straight in.
PRINTING - Infrared communication - 3 Setting up for infrared transmissions On the sending device, select the image to be printed. (P.26) Slow Blinking (POWER button) Printing 1 The film is fed out roughly 20 seconds after the printer receives the image. Hold down the POWER button (one second or more) to turn the printer on. x The POWER button lights. x If you leave the printer on, it automatically turns off (after 3 minutes when using batteries and after 10 minutes when using the AC power adapter).
PRINTING - Infrared communication - Sending images from a camera phone 1 Select the image on the mobile phone. Select infrared transmission. Rotate image Infrared transmission Delete image 3 Send infrared transmission? Guide to image sizes and transmission times The MP-300 supports IrDA high-speed communication (IrSimple/FIR). This provides faster connection speeds and shorter transmission times when the image is sent from a compatible device.
PRINTING - PictBridge Setting up for USB transmissions PICTBRIDGE 1 2 3 ENGLISH SET Select PictBridge in the digital camera’s USB setting. x For information on using your digital camera, refer to the owner’s manual supplied with the camera. NTSC OK On some digital camera models, the digital camera should be turned on at this point. Check the owner’s manual for your digital camera. Lit 2 Blinking The film is fed out roughly 20 seconds after the printer receives the image.
PRINTING - PictBridge - 4 Turn the digital camera off and then disconnect the USB cable. If 2 or more prints are set at the camera If 2 or more prints have been specified, take the film out after the first image has been printed and then proceed as described below. Blinking 5 1 2 Turn the printer off. Check that the POWER button is lit and that the PictBridge lamp is blinking. Press the REPRINT button.
Additional Information and Notes on Printing PRINTING - PictBridge - PictBridge print specification compatibility table Printable image sizes and formats Supported print specifications Multiple copies for multiple images If one or more of the selected images cannot be processed, printing ends at that point. Printing cannot be resumed mid-way through. Date and file name printing Supports up to 12 alphanumeric characters and symbols.
When the Film Runs Out 1 Check for “0”! Check that the film counter shows “0”. When the printer runs out of film, the POWER button goes dark and “0” appears on the film counter. When the film runs out while printing 1 Check for “0”! If the printer runs out of film while it is printing a specified number of images, the POWER button and the PictBridge lamp blink rapidly and “0” appears on the film counter. 1 2 Remove the photo pack. Load a new photo pack.
REPRINT Simply by pressing the REPRINT button, you can print as many copies as you like of the last image printed. Erasing the stored image When the printer is turned off, hold down the REPRINT button as you turn the printer on. This erases the stored image. x If the power is cut, the last image is stored. x Transferring a new image overwrites the stored image. x This function cannot be used with USB communication. 1 Lit Check that the printer is turned on. that the printer is 1 Check turned off.
SHARPEN Mode DATE Mode 1 Lit Turning on the power. This mode inserts the date on printed images. 2006.06.06 x This can be used with the infrared communication, USB communication and reprint functions. 2006.06.06 This mode prints images sharper and crisper. x This can be used with the infrared communication and reprint functions. When via infrared communication and reprint function is used x The POWER button lights. x During USB communication, the PictBridge lamp also lights.
ERROR - ERROR lamp - DATE Mode Lit (Approx. 7 sec. → Power off) When PictBridge is used Set date mode on the digital camera. Operating temperature too high or too low. Only use between +5°C and +40°C (+41°F and +104°F). x For information on setting date mode on your digital camera, refer to the owner’s manual for the camera. Lit ◆ When the ERROR lamp lights ◆ Take the measures described below to restore printer operation.
ERROR - LOW BATTERY lamp - ■ Troubleshooting printer problems Lit The batteries are about to run out. Lit Lit Have new batteries ready. (P.18) Case 1. Battery low. Lit Load new batteries. (P.21) ! When replacing the batteries, turn the printer ● off beforehand. ! Do not reload batteries while the printer ● (motor) is running as this could cause printer malfunctions. Case 2. You are using the wrong AC power adapter. Only use the FUJIFILM AC-5VX AC Power Adapter. (P.14, 19) Case 3.
Troubleshooting Problems The sending device sent the image, but it won’t communicate with the printer (also, the POWER button is not lit). Data transfer ended and nothing was printed. The ERROR lamp blinked (for about 7 seconds) and then the printer turned off. 44 Possible Causes Solutions 1 You left the printer on for some time without using it at all (3 minutes when using batteries and 10 minutes when using the AC power adapter). 2 The film counter shows “0”.
Troubleshooting Problems The POWER button changed from blinking to lit during data transfer and nothing was printed. Possible Causes Solutions 3 Send the data from a 3 The sending device compatible device. is not compatible with the printer. ■ Troubleshooting USB communication problems Problems Possible Causes The print menu does 1 The digital camera is not a PictBridge not appear on the supported model. digital camera. 46 Solutions Problems Error sign appears on the camera.
Glossary Troubleshooting ■ Troubleshooting problems with finished prints Problems Possible Causes 48 DPOF stands for Digital Print Order Format and refers to a format that is used for recording printing specifications for images shot using a digital camera on media such as an xD-Picture Card. The recorded specifications include information on which frames are to be printed.
Specification Photo pack used FUJIFILM Mobile Printer Photo Pack FUJIFILM instax digital film (pivi) Image enhancement functions Image Intelligence™ SHARPEN Mode Image size 61 × 46 mm (2.4 × 1.8 in.) (Film size: 86 × 54 mm (3.4 × 2.1in.)) Printing time Image recording - photo output (fed out): Approx. 20 sec.
Specification – About Mobile Printing Ready Products – This “Mobile Printing Ready” product is designed to provide easy printing from mobile phones. This product follows Mobile Imaging and Printing Consortium (MIPC) Implementation Guitelines for Printing with Mobile Terminals Version 2.0 for (Select) About MIPC (Mobile Imaging and Printing Consortium) The MIPC is a non-profit industry association founded in 2004 by leading companies in photo printing and the mobile phone industry.