JP EN 使用説明書/困ったときには/安全にご使用いただくために User’s Guide/Trouble shooting/Safety precautions BOC703-100
日本語: 3ページから27ページをご覧ください。 ENGLISH: See pages 29 to 55. Independent JPEG Group (IJG) Licenses This software is based in part on the work of the Independent JPEG Group. © 2017 FUJIFILM Corporation. All rights reserved.
日本語 JP 目次 各部の名称................................... 4 ご使用の前に................................ 5 バッテリーを入れる/充電する..... 5 バッテリーを入れる................................5 バッテリーを充電する............................6 充電中のLED表示.................................6 フィルムパックを入れる............... 7 電源を入れる/切る....................... 8 フィルムパックを取り出す......... 13 LEDの表示について................. 14 仕様............................................ 15 このようなときは…................... 16 安全にご使用いただくために.... 19 バッテリーの取り扱いについて...... 25 バッテリー残量の確認方法....
各部の名称 JP 3 2 1 7 8 10 4 5 9 6 4 1 バッテリー残量LED 5 USBケーブル接続部カバー 2 フィルム残量LED 6 USBケーブル接続部 3 プリント出口 7 フィルムパック蓋ロック 4 電源ボタン 8 リプリントボタン 9 10 電池蓋 フィルムパック蓋
ご使用の前に • プリンターをご使用になる前に、 ご使用の端末にアプリケーションをインストールしてください。 • Android OSの端末をご使用の場合は、Google Playから「スマホdeチェキ」を検索し、 インストールしてください。 *Android OSの端末の動作環境:Android Ver 4.0.3以上、 かつGoogle Playがインストールされている • iOSの端末をご使用の場合は、App Storeから 「スマホdeチェキ」を検索し、 インストールしてください。 *iOSの端末の動作環境:iOS Ver 8.
バッテリーを入れる/充電する(続き) バッテリーを充電する JP USBケーブルの端子の向きに注意してください。端 ) が上になるように接続してください。 子のマーク ( 充電中のLED表示 表示 赤点灯(電源オン時) 赤点滅(電源オフ時) バッテリーの状態/対処 充電中です。 オレンジ点灯(電源オン時) 充電が半分完了してい オレンジ点滅(電源オフ時) ます。 緑点灯(電源オン時) 緑点滅(電源オフ時) プリンターとご使用のスマートフォンなどのACパワーア ダプターを、付属のUSBケーブルで接続し、ACパワーア ダプターを屋内のコンセントにつなぎます。 バッテリー残量LEDで、 バッテリーの充電状態を確認す ることができます。詳細は右の表を参照してください。 充電がほぼ完了してい ます。 緑点滅後、消灯(電源オフ時) 充電が完了しています。 緑色、赤色に交互に点滅ま エラーが発生しています。 たは赤点滅後、消灯 充電を止めてください。 パソコンから充電するときは: • 定格出力がDC 5.
フィルムパックを入れる 注意 フィルムを使い切るまでは、フィルムパック蓋を開けないで下さい。途中で開けると、フィルムが感光し て白くなり、写真が写りません。 JP • フィルムパックを入れるときは、 フィルムパック背面の2カ所の長方形の穴は絶対に押さないでください。 • 有効期限を過ぎたフィルムは絶対に使用しないでください(故障の原因となります)。 富士フイルム インスタントフィルム instax SQUAREをご使用ください。instax miniフィルムやinstax WIDEフ ィルムはご使用になれませんので、 ご注意ください。 フィルムパックについて • フィルムパックには1枚の黒色のフィルムカバーと10枚のフィルムが収納されています。 • フィルムパックはプリンターに入れる直前に内装袋から取り出してください。 • フィルムパック蓋を閉めると、 フィルムカバーが自動的に排出されます。 詳細は、富士フイルム インスタントフィルム instax SQUAREの取扱説明を参照してください。 Ÿ ~ 2 1 フィルムパック蓋ロックを押し下げてから、 フィルム パック蓋を開きます。 フィルムパック
フィルムパックを入れる(続き) 電源を入れる/切る ! JP フィルムパック蓋ロックがカチッと止まるまで 押し込んで、 フィルムパック蓋を閉めます。 ⁄ 電源ボタンを約1秒間長押しして、電源をオンまたはオ フにします。 電源をオンにすると、 バッテリー残量LEDが点灯します。 一定時間操作を行わなかった場合、 プリンターの電源が 自動的に切れます。 バッテリー残量の確認方法 電源をオンにしたときやプリント中に、 バッテリー残量 LEDで確認できます。 表示 フィルムパック蓋を閉めると、 自 動的にフィルムカバー(黒色) が 排出されるので取り除きます。 緑色 オレンジ色 赤色 赤く点滅後、電源 オフ 8 バッテリーの残量 十分です。 半分になっています。 残りわずかです。充電することを おすすめします (6ページ参照) バッテリー残量がありません。 充電してください。 (6ページ参照)
接続・プリントする プリント時のご注意 Ÿ JP 1..プリンターは縦置きで使用してください。 2..安定した机の上などに置いてプリントしてください。 iOSの端末の無線LAN設定 iOSの端末をご使用の場合は、以下の手順で無線LAN の設定を行ってください。 1..ご使用の端末の「設定」 メニューで、 「Wi-Fi」を「オン」にする 2...
接続・プリントする(続き) JP ⁄ 「接続してプリントする」を タップします。 ¤ 「接続してプリントする」を タップする前に右下の をタップすると、編集メニュ ーが表示され、 テンプレー トの追加や画像の調整が できます。 設定が終わったら、 「完了」 をタップします。 安定した机の上などに置い てプリントしてください。 パスワードを工場出荷時状態「1111」に戻す 場合は、電源オフの状態で、 リプリントボタン を押しながら電源ボタンを押してください。 @ INSTAX-1111 10 1111 工場出荷時のパスワード 「1111」 または設定したパ スワードを入力し、 「OK」を タップします。 画像がプリントされます。 プリンターが検出されたら、 「接続」をタップします。 複数のプリンターが検出さ れた場合は、接続したいプリ ンターを一覧から選択して ください。 プリンターの識別名(SSID) は、 プリンターの底面に記載 されています。 # フィルムを排出する音が止まってか ら、送り出されたフィルムの先端を 持って取り出します。 プリントが1枚終了するごとに、 フィ ルム残量
接続・プリントする 端末とプリンターが接続されている場合: ! JP ~ 電源ボタンを約1秒間長押しして、電源をオンに します。 バッテリー残量LEDが点灯します。 Ÿ あらかじめ端末にダウンロードしたアプリケーション 「スマホdeチェキ」を起動します。 プリントする写真を選択 または撮影します。 ⁄ 「プリント」をタップします。 画像がプリントされます。 • 安定した机の上などに 置いてプリントしてくだ さい。 •「プリント」をタップする 前に右下の をタップす ると、編集メニューが表 示され、 テンプレートの 追加や画像の調整がで きます。 設定が終わったら、 「完了」 をタップします。 次のページに続く 11
JP 接続・プリントする(続き) もう1枚プリントする(リプリント) @ ~ リプリントボタンを 1回押します。 フィルムを排出する音が止まってか ら、送り出されたフィルムの先端を 持って取り出します。 プリントが1枚終了するごとに、 フィ ルム残量LEDが1つ消灯します。 Ÿ リプリントボタンを押すたびに、直前にプリント した画像がもう1枚プリントされます。 • 電源をオフにしても、前回プリントした画像は記憶さ れています。 (「スマホdeチェキ」から画像を保存す る/しないを設定できます。) • 新しく画像をプリントすると、記憶されている画像は 上書きされます。 • リアルタイムテンプレートをリプリントすることはで きません。 • リプリントをくり返し行うと、色味が少し変わる場合 があります。 12
画像を消去する フィルムパックを取り出す ~ JP プリンターの電源がオンの状態で、 リプリントボタン を5秒以上長押しします。 フィルムがなくなると、 すべてのフィルム残量LEDが ゆっくりと点滅します。フィルムパックを取り出してく ださい。 ~ Ÿ フィルムパック蓋ロックを押し下げてから、 フィルムパック蓋を開きます。 フィルム残量LEDが1秒間点滅し、画像が消 去されます。 Ÿ フィルムパックの長 方形の穴をつまみ、 フィルムパックを引 き出します。 13
LEDの表示について JP フィルム残量LEDの表示 バッテリー残量LEDの表示 フィルム残量、 プリンターの動作やエラーの警告など を表示します。 プリントが1枚終了するごとに、 フィルム残量LEDが1 つ消灯し、 フィルム残量がなくなると、 ゆっくりと点滅 します。 その他の表示については、下の表を参照してください。 バッテリーを充電しているときのプリンターの状態と、 プリンターのバッテリー残量を表示します。 動作、状態 リプリント画像を消去した。 パスワードをリセットした。 リプリントする画像がない。 LEDの表示 1秒間高速で点滅 3秒間ゆっくりと点滅 フィルムパックが入っていない。 ゆっくりと点滅 フィルム残量がない。 展開エラーまたは通信エラー 高速で点滅 が発生した。 14 バッテリーを充電しているときの状態の表示について は6ページを、 ブリンターのバッテリー残量の表示につ いては、8ページを参照してください。
仕様 instax SP-3 記録方式 有機ELによる3色露光方式 使用フィルム 富士フイルム インスタントフィルム instax SQUARE(別売) フィルム枚数 10枚/パック プリント画面サイズ 62mm × 62mm プリント画素数 800×800ドット プリント解像度 12.5ドット/mm(318dpi、80μmドットピッチ) プリント階調 RGB各色 インターフェース 準拠規格:IEEE802.11b/g/n 使用周波数:2412MHz〜2462MHz(11ch) プリント可能画像フォーマット JPEG、PNG 画像書き込み時間 画像データ受信完了後、書き込みからフィルム排出まで約13秒 プリント枚数の目安 約160枚(当社試験条件による) * 注意:使用条件により、 プリント枚数は異なります。 電源 充電式バッテリー 充電時間 約3時間(バッテリーの残量によって異なります。) 消費電力 3W 動作温度 +5℃~+40℃ (結露のないこと) JP 256階調 NP-50(1個) 大きさ・質量(重さ) 116mm × 130.
このようなときは… JP 使用中このようなときは… このようなときは 考えられる原因 こうしてください 電源が入らない。 ① バッテリーが消耗している (バッテリ ① バッテリーを充電してください。 ー残量LEDが赤色に点滅している)。 ② バッテリーを正しく入れてください。 ② バッテリーの入れ方が間違っている。 ③ 電源ボタンを長押し (約1秒) してください。 ③ 電源ボタンを押す時間が短かった。 パスワードを入力して もプリンターと接続で きない。 ● パスワードが間違っている。 ● パスワードを工場出荷状態(1111)に戻すため に、 リプリントボタンを押しながらプリンターの電 源を入れてください。 ① 画像を送信してプリントしてください。 リプリントボタンを押し ① 記憶している画像がない(フィルム ② 新しいフィルムパックを入れてください。 てもプリントされない。 残量LEDが3秒点滅します)。 ② フィルムの枚数が残っていない(フィル ③ 新しいフィルムパックを入れてください。 ム残量LEDがすべて点滅しています)。 ③ フィルムパックが入っていない(フィル ム残量LEDがす
考えられる原因 こうしてください フィルムが最後まで排 出されない。 このようなときは ● 振動や落下などの衝撃で、 フィルム がずれた。 ① フィルムの先端を持ち、少し強く引っ張ってくださ い。 ② もう一枚プリントしてください。次のフィルムが押 し出して排出されます。 フィルムが排出され ない。 ① 振動や落下などの衝撃で、 フィルム がずれている。 ② フィルムが詰まった。 ① 新しいフィルムパックを入れてください。 ② バッテリーを入れ直してください。それでも改善 されない場合は、詰まったフィルムを取り除いて から、新しいフィルムパックを入れてください。 JP LEDの表示がこのようなときは… このようなときは 考えられる原因 こうしてください フィルム残量LEDが高 ● プリンターの動作に異常が発生し 速で点滅した後、勝手に た。 電源が切れた。 ● プリンターの電源を入れてください。 バッテリー残量LEDが ● バッテリーが消耗している。 赤く点滅した後、勝手に 電源が切れた。 ● バッテリーを充電してください。 バッテリー残量がごくわずかの場合は、 プリンター を
このようなときは 充電中にバッテリー残 量LEDが赤く点滅した 後、消灯した。 JP 考えられる原因 ● 動作温度範囲外で充電している。 バッテリー残量LEDが ● バッテリーの寿命が過ぎている、 ま 高速で、緑と赤に交互に たはUSBケーブル、ACアダプタが 点滅している 故障している。 こうしてください ● 5℃から40℃の範囲内で充電してください。 ● バッテリーやUSBケーブル、ACアダプタを新し いものに交換してください。 プリントがこのようなときは… 18 このようなときは 考えられる原因 こうしてください 出来上がった写真の一 部または全部が白くな っている。 ● フィルムが残っている途中で裏ぶた を開けた。 ● フィルムを使い切るまで、裏ぶたを開けないでく ださい。フィルムが残っている状態で裏ぶたを開 けるとフィルムが感光して、感光した部分が白くな ります。 画面にむらがある。 ① プリントされた直後に圧力がかかっ た。 ② プリントがスムーズに送り出されな かった。 ① プリントを振る、曲げる、折る、押さえるなどしない でください。 ② プリント出口をふさがな
安全にご使用いただくために ● この製品および付属品は、プリント以外の目的に使用しないでください。 ● 製品の安全性には十分配慮しておりますが、下記の内容をよくお読みの上、正しくご使用ください。 ● この説明書はお読みになった後で、いつでも見られるところに必ず保管してください。 警 告 注 JP 意 この表示を無視して誤った取り扱いをすると、人が死亡また この表示を無視して誤った取り扱いをすると、人が傷害を は重傷を負う可能性が想定される内容を示しています。 負う可能性が想定される内容または、物的損害の発生が 想定される内容を示しています。 警 告 プリンター(バッテリー)が熱くなる、煙が出る、焦げ臭いなどの異常を感じたときは、ただちにバッテリーを取り出 し、USBケーブルを抜いてください。発火ややけどの原因となります。 (バッテリーを取り出す際やUSBケーブルを抜く 際、やけどには十分ご注意ください) プリンターを水中に落としたり、内部に水または金属や異物などが入ったときは、ただちにバッテリーやUSBケーブル を外してください。発熱・発火の原因となります。 引火性の高いガスが充満している場
注 意 絶対に分解しないでください。けがの原因となることがあります。 故障した場合は、絶対に自分で修理しようとせずに、 お買い上げ店にご相談ください。 落下などにより内部が露出したときは、絶対に触れないでください。けがの原因となることがあります。 フィルムパック蓋内部の部品、突起物には触れないで下さい。けがや故障の原因となることがあります。 プリンターをぬれた手で触らないでください。感電の原因となることがあります。 バッテリーのCDを誤って装てんしないようにご注意ください。バッテリーの破裂、液もれにより、発火、 けがや周囲を 汚損する原因となることがあります。 旅行などで長期間、 プリンターをご使用にならないときは、 バッテリーやUSBケーブルを外してください。火災の原因 となることがあります。 USBケーブルを接続したままプリンターを移動しないでください。USBケーブルが傷つき、火災・感電の原因となる ことがあります。 小さいお子様の手の届くところに置かないでください。けがの原因になることがあります。 本製品を布や布団でおおったりしないでください。熱がこもりケースが変形し、火災の原因になることがあります
4 フィルム室に汚れやほこりがあると、 プリントの仕上がりに影響します。フィルム室に汚れやほこりがつかないようにご注 意ください。 5 閉めきった自動車の中や、高温の場所、湿気のある場所、海岸などに長時間放置しないでください。 6 ナフタリンなど防虫剤のガスは、 プリンターにもフィルムにも有害ですから、 たんすなどへの収納は避けてください。 7 このプリンターはマイクロコンピューターによって制御されているため、 ごくまれにプリンターが誤作動する場合があり ます。このようなときは、電池をいったん取り出し、 しばらくしてから再度入れ直して下さい。 8 このプリンターの使用温度範囲は+5℃から+40℃です。 9 航空機内や病院の中でのプリンターのご使用はおやめください。航空機や病院の制御装置などの誤作動の原因となる ことがあります。 0 ラジオやテレビの受信障害となっている場合は、本機をラジオやテレビから離してください。 - プリントする際は、 ご使用になる送信側の機器の使用説明書をお読みの上、使用環境条件などを守って正しくお使いく ださい。 = プリントされる場合は、著作権、 肖像権、 プライバシーなどの他人の権
フィルム、プリントの取り扱い JP フィルム、写真の取り扱いかたについては、富士フイルム インスタントフィルム instax SQUAREの取扱説明書を参照し てください。 1 フィルムは、涼しい乾燥した場所に保管してください。特に閉め切った自動車の中などの極端に高温の場所に長時間放 置しないでください。 2 プリンターに入れたフィルムは、 できるだけ早くプリントしてください。 3 フィルムを極端に温度の低い場所や高い場所に置いてしまった場合は、通常の温度になじんでからプリントしてください。 4 フィルムは有効期限内にお使いください。 5 空港の預け入れ荷物検査などでの強いX線照射を避けてください。未使用のフィルムにカブリなどの影響が出る場合が あります。手荷物としての機内持ち込みをおすすめします (詳しくは各空港でご確認ください)。 6 プリントは強い光を避け、涼しく乾燥した場所に保存してください。 7 フィルムに穴をあけたり、破いたり、切ったりしないでください。フィルムが損傷した場合は、使用しないでください。 フィルムや出来上がった写真を取り扱うときの注意 詳細は、富士フイルム インスタントフィルム
無線LAN 機器使用上の注意事項 重要!本製品に搭載されている無線LANをご使用になる前に必ずお読みください。 ■ 本製品は無線LAN機器としてお使いください。 無線LAN機器以外として使用されたことにより損害が発生した場合、当社はいかなる責任も負いかねますので、あらか じめご了承ください。医療機器や人命に直接的または間接的に関わるシステムなど、高い安全性が要求される用途には 使用しないでください。無線LAN機器よりも高い信頼性が要求される機器や電算機システムなどの用途に使用すると きはご使用になるシステムの安全設計や故障に対する適切な処置を万全におこなってください。 ■ 無線LAN機能はお買い求め頂いた国での利用を前提としています。 本製品の無線LAN機能はお買い求め頂いた国の電波に関する法律に準拠しております。ご使用の際は、 お使い頂く国 の法律を順守してください。お買い求め頂いた国以外でのご使用上のトラブル等については、弊社では一切の責任を負 いかねます。 ■ 電波によるデータの送受信は傍受される可能性があります。 電波によるデータ (画像)の送受信は傍受される可能性があります。あらかじめご了承ください
JP ■ 本製品を使用する場合は、前項の機器や無線局と電波干渉する恐れがあるため、以下の事項に注意してください。 無線局が運用されていないことを確認してください。 万一、本製品から移動体識別用の構内無線局に対して電波干渉の事例が発生した場合は、速やかに本製品の使用周波 数を変更して、電波干渉をしないようにしてください。 その他、本製品から移動体識別用の特定小電力無線局に対して電波干渉の事例が発生した場合など何かお困りのこと が起きたときは、当社サービスセンターへお問い合わせください。 2.4DS/OF4 本製品が2.
バッテリーの取り扱いについて ● 製品の安全性には十分配慮しておりますが、下記の内容をよくお読みの上、正しくご使用ください。 警 告 注 意 JP この表示を無視して誤った取り扱いをすると、人が死亡また この表示を無視して誤った取り扱いをすると、人が傷害を は重傷を負う可能性が想定される内容を示しています。 負う可能性が想定される内容または、物的損害の発生が 想定される内容を示しています。 警 告 指定外の方法でバッテリーを使用しない。 禁止 バッテリーは極性(CD)表示どおりに入れてください。 バッテリーを分解、加工、加熱しない。/バッテリーを落としたり、衝撃を加えない。/バッテリーをショートさせない。/ バッテリーを金属製品と一緒に保管しない。/バッテリーを指定以外の充電器で充電しない。/バッテリーを火気に近 禁止 づけたり火の中に入れたりしない。/バッテリーを水にぬらさない。 バッテリーの破裂・液漏れにより、火災・けがの原因になります。 禁止 表示された電源電圧以外の電圧で使用しない。 火災の原因になります。 禁止 バッテリーの液が漏れて、目に入ったり、皮膚や衣服に付着したときは
注 JP 意 強制 お手入れの際や長時間使用しないときは、バッテリーを外す。 火災・感電の原因になることがあります。 強制 異常が起きたら電源を切り、バッテリーを外す。 煙が出ている、異臭がするなど異常状態のまま使用すると、火災・感電の原因になります。 • お買上げ店にご相談ください。 電源についてのご注意 バッテリーを上手に長くお使いいただくため、下記をお読みください。使い方を誤ると、 バッテリーの寿命が短くなるばかり か、液漏れ、発熱・発火の恐れがあります。 ※ バッテリーは出荷時にはフル充電されていません。お使いになる前に必ず充電してください。 ※ バッテリーを持ち運ぶときは、 プリンターに取り付けるか、 ソフトケースに入れてください。 ■ バッテリーの特性 • バッテリーは使わなくても、少しずつ放電しています。プリンターを使用する直前(1~2日前) に充電したバッテリーを 用意してください。 • バッテリーを長く持たせるには、 できるだけこまめに電源を切ることをおすすめします。 • 寒冷地や低温時ではプリントできる枚数が少なくなります。充電済みの予備バッテリーをご用意ください。また、使用
■ バッテリーの寿命について 常温で使用した場合、 約300回繰り返して使えます。使用できる時間が著しく短くなったときは、 バッテリーの寿命です。 新しいバッテリーをお買い求めください。 ■ 保存上のご注意 • 充電された状態で長期間保存すると、特性が劣化することがあります。 しばらく使わない場合は、使い切った状態で保存 してください。 • 使用しないときは必ずバッテリーをプリンターから取り外してください。 • 涼しいところで保存してください。 - 周囲の温度が+15℃~+25℃くらいの乾燥したところをおすすめします。 - 暑いところや極端に寒いところは避けてください。 ■ 使用上のご注意 • バッテリーにラベルなどをはらないでください。プリンターから取り出せなくなることがあります。 • 外装ラベルを破ったり、 はがしたりしないでください。 • 端子は常にきれいにしておいてください。 プリンター本体やバッテリーが熱を帯びますが、 • 長時間高温の場所に置かないでください。また、長時間使用していると、 故障ではありません。 ■ 小形充電式電池のリサイクルについて 小形充電式電池(リチウムイオンバッテリーまたはニ
ENGLISH Contents Parts Name............................................ 30 Before Use.............................................. 31 Inserting/Charging the Battery...... 31 Inserting the Battery......................................31 Charging the Battery.....................................32 Charging Indicator.........................................32 Loading the instax SQUARE Film Pack..... 33 Turning on/off the Printer................ 34 Unloading a Used instax SQUARE Film Pack....................
Parts Name 3 2 1 7 8 EN 10 4 5 9 6 30 1 Battery remaining LED 5 USB connector cover 2 Film remaining LED 6 USB connector 3 Print exit 7 Back cover lock 4 POWER button 8 REPRINT button 9 10 Battery cover Back cover
Before Use • Before using the printer, install the instax SHARE application on your device. • When you are using an Android OS device, search for “instax SHARE” in the Google Play, then install the application. * System requirements of an Android OS device: Android Ver 4.0.3 or later and Google Play are installed. • When you are using an iOS device, search for “instax SHARE” in the App Store, then install the application. * System requirements of an iOS device: iOS Ver 8.0 or later is installed.
Inserting/Charging the Battery (Continued) Charging the Battery Be careful of the orientation. Connect the USB cable ) on the terminal facing up. with the mark ( Charging Indicator Indication Lights red (ON) Flashes red (OFF) Battery status/Action Charging is in progress. Lights orange (ON) Charging is half completed.
Loading the instax SQUARE Film Pack Caution Do not open the back cover until you have used up the film; otherwise, the rest of the film will become exposed and turn white. The film can no longer be used. • When you load the film pack, never press the two rectangular holes on the back of the film pack. • Never use a film pack beyond its shelf life; otherwise, it may damage the printer. Use FUJIFILM Instant Film “instax SQUARE” only. The instax mini film or instax WIDE film cannot be used.
Loading the instax SQUARE Film Pack (Contunued) Turning on/off the Printer ! EN Close the back cover. Make sure the back cover lock clicks into place. ⁄ Press and hold the POWER button for approx. 1 second to turn the printer on or off. Turning the printer on lights up the battery remaining LED. If no operation occurs for a certain period of time, the printer turns off automatically.
Connecting and Printing Notes on Printing Ÿ 1. Place the printer vertically. 2. When printing, put the printer on a steady surface such as a desk. EN Wireless LAN Setup for iOS Devices When you are using an iOS device, follow the procedure below to perform wireless LAN setup. Start the downloaded application “instax SHARE”. 1. Select “ON” for “Wi-Fi” in the “Settings” menu of your device. 2. Tap the network name (printer name) under “Choose a Network”.
Connecting and Printing (Continued) ⁄ Tap “Connect and print”. Before tapping “Connect on and print”, tapping the lower right displays the edit menu. You can add a template or adjust an image on this menu. Tap “Done” to exit from the menu. EN 1111 When printing, put the printer on a steady surface such as a desk. To reset the password to the factory default (1111), turn the printer on while holding the REPRINT button.
Connecting and Printing When connection is already established: ! ~ EN Press and hold the POWER button for approx. 1 second to turn the printer on. The battery remaining LED lights up. Ÿ Start the downloaded application “instax SHARE”. Select the picture to print or take a picture. ⁄ Tap “Print”. The printer starts printing. • When printing, put the printer on a steady surface such as a desk. • Before tapping “Print”, on the lower tapping right displays the edit menu.
Connecting and Printing (Continued) Reprinting @ ~ Press the REPRINT button once. EN When the film has been ejected (the printer stops making a sound), grasp the edge of the film, then take it out. 1 film remaining LED turns off every time you print an image. Ÿ Every time you press the REPRINT button, the previous image is reprinted. • The last printed image is stored even if you turn the printer off. (You can select whether to store the image on the instax SHARE application.
Deleting an Image Unloading a Used instax SQUARE Film Pack ~ Press and hold the REPRINT button for more than 5 seconds with the printer on. When no film is left, all the film remaining LEDs flash slowly. Unload the film pack. EN ~ Ÿ Press the back cover lock down to open the back cover. The film remaining LED flashes for 1 second and the image is deleted. Ÿ Grasp the rectangular holes on the film pack, then pull it out.
About the LED Indication Film remaining LED indication Battery remaining LED indication The film remaining LED indicates film remaining, printer operation, or error warning. 1 film remaining LED turns off every time you print an image, and flashes slowly to indicate no film remains. See the table below for other indication patterns. The battery remaining LED indicates the printer status while charging the battery, or battery life of the printer. See page 32 for indications while charging the battery.
SPECIFICATIONS instax SP-3 Recording method Film Photo capacity Image size Supported image size Printing resolution Printing levels Interface Supported image format Printing time Approximate printing capacity Power supply Charging time Power consumption Operating temperature Dimensions/Weight Supplied accessory 3-color exposure with OLED FUJIFILM Instant Film “instax SQUARE” (Purchased separately) 10 prints/pack 62 mm×62 mm/2.4 in.×2.4 in. 800×800 dots 12.
TROUBLE SHOOTING During printing Problems The printer cannot be turned on. EN 42 Possible Causes 1 The battery power is low. (The battery remaining LED is flashing red.) 2 The battery is not inserted correctly. 3 You did not press the POWER button for long enough. Solutions 1 Charge the battery fully. 2 Insert the battery correctly. 3 Press and hold the POWER button for approx. 1 second. You entered the ● The password is incorrect. password, but the device cannot be connected to the printer.
Problems Possible Causes Solutions The film pack cannot be loaded, or cannot be loaded smoothly. 1 The film pack is not for your printer. 2 The film pack is not being loaded correctly. 1 Use FUJIFILM Instant Film “instax SQUARE” only. (No other films can be used.) 2 Match the yellow line on the film pack with the yellow positioning mark in your printer. The film cover cannot be ejected. ● The printer cannot recognize the film pack. ● Remove the film pack and load it again.
LED status Problems EN 44 Possible Causes Solutions The film remaining LED flashes rapidly, then the printer turns itself off. ● A printer error has occurred. ● Turn the printer on. The battery remaining LED flashes red slowly, then the printer turns itself off. ● The battery power is low. ● Charge the battery fully. When the remaining battery life is low, you cannot turn the printer on even though the printer is connected to the AC power outlet using the USB cable.
Printed pictures Problems Possible Causes Solutions Part or whole finished print is white. ● The back cover was opened before you have used up the film. ● Do not open the back cover until you have used up the film; otherwise, the rest of the film may be exposed and ruined for use. The picture is blurred. 1 Pressure was applied to the picture immediately after it came out from the printer. 2 The picture did not come out smoothly. 1 Do not shake, bend, fold, or press the print.
IMPORTANT SAFETY NOTICE This product has been designed with safety in mind, and to provide safe service when handled correctly and in accordance with the User’s Guide and instructions. It is important that both the product and the INSTAX film are handled properly and used only to print pictures as instructed in this User’s Guide and in the instax SQUARE film instructions. For your ease and safety, please follow what is written in this User’s Guide.
WARNING Never attempt to take this product apart. You may be injured. If anything is wrong with the printer, never attempt to repair it by yourself. You may be injured. If this product is dropped or damaged so that the inside is showing, do not touch it. Contact your FUJIFILM dealer. Do not touch any parts or projecting parts inside the back cover. You may be injured. Never get this product wet or handle it with wet hands. Doing so may result in an electric shock.
EN installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If your equipment contains easy removable batteries or accumulators, please dispose these separately according to your local requirements. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you have purchased the product.
~ Make sure the printer stands up vertically; otherwise, it may not deliver the designed performance fully. ! This printer is designed for household use. It is not suitable for commercial printing which requires a large amount of printing. Cautions during printing EN INSTAX SQUARE FILM AND PRINT CARE See FUJIFILM Instant Film “instax SQUARE” for film use instructions. Follow all instructions for safe and proper use. 1 Keep the film in a cool and dry place.
Cautions on handling the film and prints For details, refer to the instructions and warnings on FUJIFILM Instant Film “instax SQUARE”. EN Wireless Network Devices: Cautions IMPORTANT: Read the following notices before using the printer’s built-in wireless transmitter. ■ Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use.
■■ Do not use the device in locations subject to magnetic fields, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or in other locations subject to magnetic fields, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4 GHz band. ■■ The wireless transmitter operates in the 2.
Handling the Battery • Make sure that you use your printer correctly. Read these safety notes and your User’s Guide carefully before use. • After reading these safety notes, store them in a safe place. WARNING CAUTION This symbol indicates danger, which could result in injury or This symbol indicates possible damage, which could result in death. Please follow these instructions. injury to other people or damage to an object. Please follow these instructions. Please handle the product properly.
CAUTION EN Required When you are cleaning the printer or you do not plan to use the printer for an extended period, remove the battery. Failure to do so can cause a fire or electric shock. Required If a problem arises, turn the printer off and remove the battery. Continued use of the printer when it is emitting smoke, is emitting any unusual odor, or is in any other abnormal state can cause a fire or electric shock. Contact your FUJIFILM dealer.
■■ Storage Performance may be impaired if the battery is left unused for extended periods when fully charged. Deplete the battery fully before storing it. If the printer will not be used for an extended period, remove the battery and store it in a dry place with an ambient temperature of from +15 °C to +25 °C (+59 °F to +77 °F). Do not store in locations exposed to extremes of temperature. ■■ Cautions: Handling the Battery • • • • Do not affix stickers or other objects to the battery.
jp この製品に関するお問い合わせは、同封の保証書 に記載の窓口にご連絡いただくか、下記のウェブサイトに アクセスしてください。 富士フイルムホームページ:http://fujifilm.jp/ If you have any inquiries about this product, please contact a FUJIFILM authorized distributor, or access the website below.