User's Manual
Table Of Contents
- QUICK REFERENCE
- CHAPTER 1 INTRODUCTION
- CHAPTER 2 SETTING UP
- CHAPTER 3 PAPER HANDLING
- CHAPTER 4 PRINTING
- CHAPTER 5 USING SETUP MODE
- HOW TO USE THIS CHAPTER
- ENTERING SETUP MODE
- OVERVIEW OF SETUP MODE
- PRINTING A LIST OF SELECTED OPTIONS
- DECIDING WHICH OPTIONS TO CHANGE
- CHANGING MENU1 AND MENU2 OPTIONS
- CHANGING HARDWARE OPTIONS
- CHANGING PRINT POSITION ADJUSTMENT OPTIONS
- CHANGING CONFIGURATION OPTIONS
- EXITING AND SAVING
- RESETTING DEFAULTS
- USING THE DIAGNOSTIC FUNCTIONS
- SETUP MODE REFERENCE
- ONLINE SETUP MODE
- CHAPTER 6 MAINTENANCE
- CHAPTER 7 TROUBLE-SHOOTING
- APPENDIX A SUPPLIES AND OPTIONS
- APPENDIX B PRINTER AND PAPER SPECIFICATIONS
- CHAPTER C COMMAND SETS
- APPENDIX D INTERFACE INFORMATION
- APPENDIX E CHARACTER SETS
- CHARACTER SETS 1 AND 2 (DPL24C PLUS AND IBM XL24E EMULATION)
- ITALIC AND GRAPHICS CHARACTER SETS (ESC/P2 EMULATION)
- NATIONAL CHARACTER SETS (ALL EMULATIONS)
- NATIONAL CHARACTER SETS (DPL24C PLUS AND IBM XL24E EMULATION)
- NATIONAL CHARACTER SETS (ESC/P2 EMULATION)
- NATIONAL CHARACTER SETS AND SUPPORTED RESIDENT FONTS (ALL EMULATIONS)
- APPENDIX F RESIDENT FONTS
- GLOSSARY OF TERMS
C-5
Command
Sets
User's Manual
COMMAND SETS
Function Command
Set character offset to n/120 inch ESC DC1 (n)
Cancelled by CR or ESC x.
(0 - n - 63) (64 - n - 127)
Set character pitch to n/360 inch ESC e H
(0 - n
1
n
2
n
3
- 999) (n
1
) (n
2
) (n
3
)
n
1
, n
2
, and n
3
are the hundreds, tens, and
units digits.
Vertical Control
Line feed LF
Reverse line feed ESC LF
Form feed FF
Advance paper n/180 inch (0 - n - 255) ESC J (n)
Reverse paper n/180 inch (0 - n - 255) ESC j (n)
Advance paper n/360 inch ESC e J
(0 - n
1
n
2
n
3
- 999) (n
1
) (n
2
) (n
3
)
n
1
, n
2
, and n
3
are the hundreds, tens, and
units digits.
Reverse paper n/360 inch ESC e j
(0 - n
1
n
2
n
3
- 999) (n
1
) (n
2
) (n
3
)
n
1
, n
2
, and n
3
are the hundreds, tens, and
units digits.
Set line spacing to 1/8 inch (8 lpi) ESC 0
Set line spacing to n/180 inch ESC 3 (n)
(0 - n - 255)
Set line spacing to 7/60 inch ESC 1
Set line spacing to n/60 inch ESC A (n)
(0 - n - 127)
Set line spacing to 1/6 inch (6 lpi) or to the ESC 2
value set with the ESC A command.
The preset line spacing command is
ESC A (n).
Set line spacing to n/360 inch ESC e V
(0 - n
1
n
2
n
3
- 999) (n
1
) (n
2
) (n
3
)
n
1
, n
2
, and n
3
are the hundreds, tens, and
units digits.
Set line spacing to n/360 inch FS 3 (n)
(1 - n - 255)