User’s Guide Learn how to use your Fujitsu LifeBook A6210 notebook
Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.
The DVD player found in some models of the LifeBook notebook incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights users. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 19 VDC, with a current of 4.22 A (80 W).
System Disposal Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL LAWS. Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*.
Contents Preface About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Chapter 1 Getting to Know Your LifeBook Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touchpad Pointing Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Clicking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Navigating Using Gestures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Touchpad Control Adjustment . . . . . . . . . . . . . . . . . . . . . . . .
Registering Your LifeBook notebook with Fujitsu . . . . . . . . . . . . . . . . . . 54 Installing Click Me! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Fujitsu Driver Update Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Power/Suspend/Resume Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Stick/Secure Digital Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Installing Memory Stick and SD Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Removing A Memory Stick or SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Installing Memory Upgrade Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Checking the Memory Capacity . . .
Chapter 5 Care and Maintenance Caring for your LifeBook Notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Cleaning your LifeBook notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Cleaning the dust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Storing your LifeBook notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Traveling with your LifeBook notebook . . . . . . . . . . . . . . . . . . .
Glossary/Regulatory Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Appendix A: WLAN User’s Guide Before Using the Optional Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Wireless LAN Device Covered by this Document. . . . . . . . . . . . . . . . . . . 151 Characteristics of the WLAN Device . . . . . . . . . .
Using a UWB Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 What is Certified Wireless USB? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Using Certified Wireless USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Appendix B: Fingerprint Sensor Device Introducing the Optional Fingerprint Sensor Device . . . . . . . . . . . . . . . . 165 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface About This Guide The LifeBook A6210 notebook from Fujitsu Computer Systems Corporation provides desktop performance with a fast, Intel® Core™ 2 Duo processor. Your notebook has a built-in 15.4” TFT WXGA color display. This system brings the computing power of desktop personal computers (PCs) to a portable environment. Your computer comes with Microsoft Windows Vista® Business or Windows Vista® Home Premium operating system pre-installed.
THIS INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF THE SUBJECT MATERIAL. THIS CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATION CAREFULLY. THIS WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR LIFEBOOK NOTEBOOK, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.
• • • • Purchase date Conditions under which the problem occurred Any error messages that have occurred Type of device connected, if any Fujitsu Shopping Online You can go directly to the online by going to the website at: www.shopfujitsu.com. YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS. Limited Warranty Your LifeBook notebook is backed by a Fujitsu International Limited Warranty.
Chapter 1 Getting to Know Your LifeBook Overview This section describes the components of your Fujitsu LifeBook A6210 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers. Figure 1.
Locating the Controls and Connectors LifeBook Application Panel with Support Button Web Camera* Digital Microphone* Fingerprint Recognition Sensor* Touchpad Pointing Device Display Panel Status Indicator Panel Power/Suspend/Resume Button Stereo Speaker Stereo Speaker Keyboard * Optional device or feature Figure 2.
Top Components The following is a brief description of your LifeBook notebook’s top components. Web Camera The optional web camera allows you to take pictures of yourself to send over the internet. For information on using the microphone and web cam, see the documentation associated with the ArcSoft WebCam Companion application. Digital Microphone The optional digital microphone is used in conjunction with the optional web cam.
Touchpad Pointing Device The Touchpad pointing device is a mouse-like cursor control with three buttons: a right mouse-like button, a left mouse-like button, and a scroll button. The touchpad is gesture-enabled. This allows you to zoom in or out and scroll continually using simple gestures. See “Touchpad Pointing Device” on page 34. Depending upon the configuration of your system, the scroll button may be configured as a fingerprint recognition/scroll sensor device.
ExpressCard Slot Optical Drive Release Button ExpressCard Eject Button Optical Drive PC Card Slot PC Card Eject Button Emergency Optical Tray Release Figure 3. LifeBook notebook left-side panel Left-Side Panel Components The following is a brief description of your LifeBook notebook’s left-side components. ExpressCard Slot The ExpressCard Slots allow you to install an ExpressCard. See “PC Cards/ExpressCards™” on page 71.
Emergency Optical Tray Release If for some reason the eject button fails, you can open the media tray with a paper clip or similar tool inserted into the eject hole. See “Emergency Optical Drive Tray Release” on page 68. PC Card Slot The PC Card Slot allows you to install a Type I or Type II PC Card. See “PC Cards/ExpressCards™” on page 71. PC Card Eject Button The PC Card Eject Button assists you in removing a PC Card from the PC Card slot.
Headphone Jack Wireless LAN/UWB/Bluetooth On/Off Switch E-SATA Port Microphone Jack Memory Stick/SD Card Slot USB Ports DC-In Jack Figure 4. LifeBook notebook right-side panel Right-Side Panel Components The following is a brief description of your LifeBook notebook’s right-side components. Wireless LAN/UWB/Bluetooth On/Off Switch The wireless LAN/UWB/Bluetooth on/off switch is used to turn the optional WLAN, Ultra Wideband, and Bluetooth devices on and off.
E-SATA Port E-SATA (External Serial Advanced Technology Attachment) is an external version of SATA, which connects your computer to the hard drive. SATA is an interface that is much faster than typical IDE interfaces (E-SATA is six times faster than USB 2.0). E-SATA is ideal for backing up large files on an external hard drive. See “E-SATA Port” on page 85. Memory Stick/SD Card Slot The Memory Stick/SD card slot allows you to install a Memory Stick or Secure Digital (SD) card for data storage.
Air Vents HDMI Port External Video Jack USB 2.0 Ports Air Vents IEEE 1394 Port Anti-Theft Lock Slot Gigabit LAN (RJ-45) Jack Figure 5. LifeBook notebook back panel Back Panel Components Following is a brief description of your LifeBook notebook’s back panel components. Air Vents The air vents allow air to circulate through the system to cool down the components.
HDMI Port The HDMI port is used to connect compatible digital devices with your computer (such as a highdefinition television or AV receiver). See “HDMI Port” on page 85. External Video Port The external monitor port allows you to connect an external monitor or LCD projector. See “External Video Port” on page 83. USB 2.0 Ports The USB 2.0 ports allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480 Mbps and is backward-compatible with USB 1.
Dust Filter Memory Upgrade Compartment Lithium ion Battery Bay Figure 6. LifeBook notebook bottom panel Bottom Components The following is a brief description of your LifeBook notebook’s bottom panel components. Dust Filter The dust filter is used to help prevent dust and dirt from entering your system. See “Cleaning the dust filter” on page 113. Lithium ion Battery Bay The battery bay contains the internal Lithium ion battery.
Memory Upgrade Compartment Your notebook comes with high speed Double Data Rate 3 Synchronous Dynamic RAM (DDR3-1066 SO-DIMM). The memory upgrade compartment allows you to expand the system memory capacity of your notebook, thus improving overall performance. See “Memory Upgrade Module” on page 78. Under normal circumstances, it should not be necessary to open this compartment.
CapsLk NumLk ScrLk Hard Drive/ Battery Charge/ Optical Drive DC-In Power Battery Level Figure 7. Status Indicator Panel Status Indicator Panel The Status Indicators display symbols that correspond to specific components of your Fujitsu LifeBook notebook. The LEDs below each symbol tell you how each of those components is operating. The indicators can be found in two different areas, as shown above. Power Indicator The Power indicator glows blue when your system is turned on.
Battery Charge/DC-In Indicator • Orange, solid: AC adapter and battery are available and system is charging. • Green, solid: AC adapter and battery are available and system is fully charged, or AC adapter is plugged in but battery is not installed. • Orange, blinking: AC adapter and battery are available and waiting to charge battery (battery is out of thermal range). • Off: AC adapter is not plugged in.
• Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged. • A shorted battery is damaged and must be replaced. Hard Drive/Optical Drive Access Indicator The Hard Drive/Optical Drive Access indicator glows green when your internal hard drive is being accessed. Note that flickering is normal. NumLk Indicator The NumLk indicator states that the integral keyboard is set in ten-key numeric keypad mode.
Keyboard Function Keys Fn Key Start Key Numeric Keypad (surrounded by heavy line) Application Key Cursor Keys Figure 8. Keyboard Using the Keyboard Your Fujitsu LifeBook notebook has an integral 86-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys.
• Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. • Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. • Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.
Function Keys Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. • The [Fn] key provides extended functions for the notebook and is always used in conjunction with another key. • [Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.
Touchpad Pointing Device Cursor Control Right Button Scroll button or optional Fingerprint Sensor Left Button Figure 9. Touchpad pointing device The Touchpad pointing device comes built into your Fujitsu LifeBook notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left button, a right button, and a scroll button (or fingerprint sensor, depending upon your system configuration).
AN EXTERNAL MOUSE CAN BE CONNECTED TO THE USB PORTS ON YOUR LIFEBOOK NOTEBOOK AND USED SIMULTANEOUSLY WITH THE TOUCHPAD. HOWEVER, IF YOU BOOT THE SYSTEM WITH AN EXTERNAL MOUSE CONNECTED THE TOUCHPAD WILL BE DISABLED OR ENABLED DEPENDING ON THE SPECIFICATIONS IN YOUR BIOS SETTINGS. See “BIOS Setup Utility” on page 51. Clicking Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it.
Double-Clicking Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and immediately release it. You can also perform the double-click operation by tapping lightly on the Touchpad twice. Figure 13. Double-clicking with button Figure 14.
Dragging Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap.
Navigating Using Gestures The touchpad allows you to use gestures to zoom in or out on a page or scroll quickly through large documents. Zooming In: To zoom in on a page using the touchpad, simply place two fingers together on the touchpad and move them away from each other. (See Figure 17) Zooming Out: To zoom out on a page using the touchpad, place two fingers on the touchpad and move towards each other.
Touchpad Control Adjustment The Windows Control Panel allows you to customize your Touchpad with selections made from within the Mouse Properties dialog box. Figure 17. Zooming in with Touchpad Figure 18. Zooming out with Touchpad Figure 19. Continuous scrolling Figure 20.
Volume Control Your Fujitsu LifeBook notebook has multiple volume controls which interact with each other. ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF, YOU WILL OVERRIDE THE EXTERNAL VOLUME CONTROL SETTING.
Support My Home Web Search A B C Figure 22. LifeBook Application Panel LifeBook Application Panel/Support Button The Application Panel consists of buttons that allow you to launch user-defined applications with the touch of a button when your system is on. Also included in the panel is a Support button that allows you to either launch the Fujitsu Support Center utility or to launch a user-defined application. (The two Volume buttons on the right are discussed in “Volume Control” on page 40.
To configure your LifeBook Application Panel with Application Panel Setup: 1 2 3 Click on [Start]. Click on Programs, then click on LifeBook Application Panel. Click on Setup of LifeBook Application Panel. The Button Setting utility will appear. There are tabs that correspond to the application buttons on the LifeBook Application Panel. When you receive your notebook, these buttons are pre-configured to launch specific programs.
6 Click OK. The button will now launch the new application. If you want to return to launching your Windows default Internet browser with this button, you need only click on Start Browser checkbox instead of the Start program checkbox. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application” from this button, you will need to reconfigure it as described above.
Support tab The Support tab lets you automatically go to the Support Website. (You must be connected to the Internet in order to access the Support website). Launching Applications with the Support Button Your notebook is pre-installed with utilities that let you operate and configure your LifeBook Application Panel. These utilities are found in the Start menu, under Settings > Control Panel > Application Panel (or “Buttons” in some configurations). The utility includes an Application Panel Setup tab.
Chapter 2 Getting Started with Your LifeBook DC Power Jack AC Adapter 1 2 AC Cable 3 Plug Figure 23.
Power Sources Your Fujitsu LifeBook notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter. Connecting the Power Adapters The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter 1 Plug the AC Cable into the AC Adapter 2 Plug the DC output cable into the DC power jack of your LifeBook notebook. 3 Plug the AC adapter into an AC electrical outlet.
Figure 24. Opening the Display Panel Display Panel Your Fujitsu LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of active-matrix technology. Opening the Display Panel 1 2 Press the Display Panel latch button in. This releases the locking mechanism, allowing you to raise the display. Lift the display backwards, being careful not to touch the screen, until it is at a comfortable viewing angle.
Using the Keyboard Adjusting the brightness using the keyboard changes the setting only temporarily. • [Fn+F6]: Pressing repeatedly will lower the brightness of your display. • [Fn+F7]: Pressing repeatedly will increase the brightness of the display. Using the Power Options To adjust the brightness so that the setting changes remain after the system is rebooted or resumed, perform the following: 1 2 3 4 Click the Start icon, then select Control Panel.
Starting Your LifeBook Notebook Power On Power/Suspend/Resume Button The Power/Suspend/Resume button is used to turn on your LifeBook notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your LifeBook notebook. WHEN YOU TURN ON YOUR LIFEBOOK NOTEBOOK, BE SURE YOU HAVE A POWER SOURCE. THIS MEANS THAT A BATTERY IS INSTALLED AND CHARGED, OR THAT THE AC OR AUTO/AIRLINE ADAPTER IS CONNECTED AND HAS POWER.
NEVER TURN OFF YOUR LIFEBOOK NOTEBOOK DURING THE POWER ON SELF TEST (POST) OR IT WILL CAUSE AN ERROR MESSAGE TO BE DISPLAYED WHEN YOU TURN YOUR LIFEBOOK NOTEBOOK ON THE NEXT TIME. See “Power On Self Test Messages” on page 99. Boot Sequence The procedure for starting-up your notebook is termed the Bootup sequence and involves your notebook’s BIOS. When your LifeBook notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook.
BIOS Setup Utility The BIOS Setup Utility is a program that sets up the operating environment for your LifeBook notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your notebook. The BIOS Setup Utility configures: • Device control feature parameters, such as changing I/O addresses and boot devices. • System Data Security feature parameters, such as passwords.
Clicking on any of the fields will invoke the screen, information, or action described. The Boot Menu can also be invoked by pressing the [F12] key when the Fujitsu logo appears on the screen. BIOS Guide A guide to your notebook’s BIOS is available online. Please visit our service and support website at http://www.computers.us.fujitsu.com/support, then select User’s Guides under Online Support. Select your Product, Series, and Model, then click [Go]. Under the Manuals tab, select the BIOS Guide.
1 First of all, you will need to read and accept the End User License Agreements (EULAs). • IF YOU REJECT THE TERMS OF THE LICENSE AGREEMENTS YOU WILL BE ASKED TO REVIEW THE LICENSE AGREEMENTS FOR INFORMATION ON RETURNING WINDOWS OR TO SHUT DOWN YOUR LIFEBOOK NOTEBOOK. • YOU CANNOT USE YOUR NOTEBOOK UNTIL YOU HAVE ACCEPTED THE LICENSE AGREEMENTS. IF YOU STOP THE PROCESS YOUR NOTEBOOK WILL RETURN TO THE BEGINNING OF THE WINDOWS WELCOME PROCESS, EVEN IF YOU SHUT YOUR NOTEBOOK DOWN AND START IT UP AGAIN.
Registering Your LifeBook notebook with Fujitsu You can register your LifeBook by going to our website at: us.fujitsu.com/computers You will need to be set up with an Internet Service Provider (ISP) to register online. Installing Click Me! BEFORE INSTALLING THE CLICKME! UTILITY, BE SURE THE WIRELESS LAN SWITCH IS TURNED ON. The first time you boot up your system, you will see a “Primary Settings for the PC” window. This window explains the installations which will be performed by the Click Me! utility.
Power Management Your Fujitsu LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention; however, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your notebook may be controlled from settings made in your operating system, prebundled power management application, or from settings made in BIOS setup utility.
• Pressing the Power/Suspend/Resume button when your system is turned on. • Selecting Sleep from the Windows Shut Down menu. • Timing out from lack of activity. • Allowing the battery to reach the Dead Battery Warning condition. Your notebook’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Sleep mode, your notebook will return to the point where it left off.
Hibernation (Save-to-Disk) Feature The Hibernation feature saves the contents of your notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation Feature The default settings are not enabled. To enable or disable the Hibernation feature follow these steps: 1 2 From the Start menu, select Control Panel.
Powering Off Before turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your notebook shuts down without error, use the Windows shut down procedure. • BE SURE TO CLOSE ALL FILES, EXIT ALL APPLICATIONS PRIOR TO TURNING OFF THE POWER. IF FILES ARE OPEN WHEN YOU TURN THE POWER OFF, YOU WILL LOSE ANY CHANGES THAT HAVE NOT BEEN SAVED, AND MAY CAUSE DISK ERRORS.
Chapter 3 User-Installable Features Lithium ion Battery Your LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.
• ACTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS, APPLICATIONS, FEATURES, POWER MANAGEMENT SETTINGS, BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES. CD-ROM DRIVE, MULTI-FORMAT DVD WRITER, DVD/CD-RW DRIVE COMBO, OR HARD DRIVE USAGE MAY HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE. THE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF THE BATTERY IS RUNNING LOW QUICKLY, REPLACE IT WITH A NEW ONE.
USING HEAVY CURRENT DEVICES SUCH AS FREQUENT DVD/CD-RW/CD-ROM ACCESSES MAY PREVENT CHARGING COMPLETELY. Low Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your notebook will go into Sleep mode. There is no guarantee that your data will be saved once the notebook reaches this point.
Replacing the Battery With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. There are two ways to swap batteries, cold-swapping and hot-swapping: Cold-swapping Batteries To cold-swap batteries in your battery bay follow these easy steps: 1 2 3 4 Have a charged battery ready to install. 5 6 Insert a new battery into the bay, and press it down so that the latches click into place. Shut down your notebook and disconnect the AC adapter.
Hot-swapping Batteries To hot-swap batteries in your battery bay follow these easy steps: BE SURE TO PLUG IN AN AC ADAPTER PRIOR TO REMOVING THE BATTERY. THERE IS NO BRIDGE BATTERY PRESENT TO SUPPORT THE SYSTEM WHILE THE BATTERY IS BEING REPLACED. IF YOU DO NOT USE AN AC ADAPTER YOU WILL LOSE ANY UNSAVED FILES. 1 2 Plug an AC Adapter into the system and connect it to a power outlet. Follow steps 3 through 6 in “Cold Swapping Batteries”.
Media Tray Eject Button Media Holder Tray Left side of notebook pictured Emergency Tray Release Figure 26. Optical Drive Optical Drive Your Fujitsu LifeBook notebook contains an optical drive which is either a Dual-Layer Multi-Format DVD Writer or a high-definition (HD) Blu-ray™ ROM player.
Media Player Software With the Dual-Layer Multi-Format DVD Writer and media player software you can play DVD movies and music CDs on your notebook. The media player includes controls which allow you to take full advantage of the features of a DVD movie, as well as standard features such as fast forward, fast reverse, pause, etc. With this drive you can also burn onto recordable DVD-R/RW, DVD+R/RW, or CD-R/RW discs.
• YOU SHOULD PERIODICALLY CHECK THE FUJITSU WEBSITE AT US.FUJITSU.COM/COMPUTERS FOR THE MOST CURRENT DRIVERS. • ALL LIFEBOOK DVD PLAYERS ARE SET TO PLAY DVD TITLES WITH REGION CODE NUMBER 1 WHICH IS NORTH AMERICAN MARKET. THE REGION NUMBER IS A REGIONAL RESTRICTION DVD FORUM ACTING ON HOLLYWOOD REQUIREMENTS. DIFFERENT REGION CODES ARE RECORDED ON VIDEO DVD TITLES FOR PUBLICATION IN DIFFERENT AREAS OF THE WORLD.
a. b. c. d. Figure 27. Loading/Ejecting Media Removing Media 1 Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the LifeBook notebook a short distance. 2 3 4 Gently pull the tray out until the disc can easily be removed from the tray. Carefully remove the media disc from the holder tray. Gently push the holder tray back in until you hear a click.
Emergency Optical Drive Tray Release If for some reason the eject button fails, you can open the media tray with a paper clip or similar tool inserted into the eject hole in the right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole. The tray will pop out. Figure 28. Emergency Tray Release Using the Media Player Software DEPENDING UPON ITS CONFIGURATION, YOUR SYSTEM MAY NOT HAVE THE MEDIA PLAYER SOFTWARE PRE-INSTALLED.
1 2 Right-click on the movie screen to open a dropdown menu for options. Select View, then Player for all the controls available. This will open the control panel into the bottom of the screen. Using the Media Player Control Panel The media player software allows you to watch the movie much like a VCR player. You can pause, rewind, fast-forward and stop the movie at any point. 1 2 To pause the movie, click the on-screen button.
• MANY MOVIE RUN-TIMES ARE LONGER THAN YOUR SYSTEM CAN SUPPORT ON A SINGLE BATTERY. IF YOU ARE WATCHING A DVD MOVIE ON BATTERY POWER YOU MAY NEED TO SWAP IN AN ADDITIONAL, AC POWER DURING THE MOVIE TO VIEW IT IN ITS ENTIRETY. CHARGED BATTERY OR ATTACH • AN ADDITIONAL FULLY-CHARGED BATTERY IS HIGHLY RECOMMENDED IF YOU WILL BE WATCHING DVD MOVIES ON BATTERY POWER. IF YOU DON’T HAVE AN ADDITIONAL BATTERY, YOU MAY PURCHASE ONE EITHER ONLINE AT: HTTP://WWW.COMPUTERS.US.FUJITSU.
PC Card PC Card Slot (bottom slot) PC Card Eject Button Figure 29. Installing/Removing PC Card PC Cards/ExpressCards™ Your LifeBook supports Type I and Type II PC Cards and ExpressCardsTM, which can perform a variety of functions depending on which type of card you install. You can install one or two cards at a time, depending on its type. PC Cards should be installed in the bottom slot, and ExpressCards in the top slot.
Installing PC Cards PC Cards are installed in the PC Card slot (the lower of the two slots). To install a PC Card: • INSTALLING OR REMOVING A PC CARD DURING YOUR LIFEBOOK NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK NOTEBOOK. • DO NOT INSERT A PC CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR LIFEBOOK NOTEBOOK, OR BOTH. • EVEN WHEN THEY ARE NOT BEING USED, INSTALLED PC/EXPRESSCARDS CONSUME POWER.
1 Unlock the card from the slot by pressing the eject button associated with the slot in which the card is located. When pressed, the button will pop out. 2 Firmly press the button again until it is flush with the notebook. This will eject the card slightly out of the slot allowing you to remove the card. IF THE PC CARD HAS AN EXTERNAL CONNECTOR AND CABLE, DO NOT PULL THE CABLE WHEN REMOVING THE CARD. Installing ExpressCards There are two different width ExpressCards: 34 mm and 54 mm.
• INSTALLING OR REMOVING AN EXPRESSCARD DURING YOUR NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR NOTEBOOK. • DO NOT INSERT AN EXPRESSCARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR NOTEBOOK, OR BOTH. YOU MAY BE REQUIRED TO LOG ON AS ADMINISTRATOR OR A MEMBER OF THE ADMINISTRATOR’S GROUP TO COMPLETE THIS PROCEDURE.
To remove an ExpressCard, follow these steps: 1 Unlock the card from the slot by pressing the eject button associated with the slot in which the card is located. When pressed, the button will pop out. 2 Firmly press the button again until it is flush with the notebook. This will eject the card slightly out of the slot allowing you to remove the card.
SD Card Memory Stick Memory Stick/SD Card Slot Figure 31. Memory Stick and SD Card Figure 32. Installing a Memory Stick/SD Card Memory Stick/Secure Digital Cards Your LifeBook notebook supports Memory Stick, Memory Stick Pro, Secure Digital (SD), and Secure Digital High Capacity (SDHC) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.
Installing Memory Stick and SD Cards Memory Stick and SD Cards are installed in the Memory Stick/SD Card slot. To install a card, follow these steps: INSTALLING OR REMOVING A MEMORY STICK OR SD CARD DURING YOUR LIFEBOOK NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK NOTEBOOK. DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS LIFEBOOK NOTEBOOK, OR BOTH.
Memory Upgrade Module Your Fujitsu LifeBook notebook comes with a minimum of 2GB (either a single 2 GB module or two 1 GB modules) of high speed Double Data Rate Synchronous Dynamic RAM (DDR3-1066 SDRAM) factory installed. To increase your notebook’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. Note: Before you purchase additional module(s), be sure to check first to see whether you have one or two modules pre-installed.
6 Align the memory upgrade module with the part side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. Be sure the alignment keys line up with those in the slot. Alignment keys Figure 33. Opening the Memory Compartment Figure 34. Installing a Memory Module 7 Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip.
Removing a Memory Module 1 Perform steps 1 through 4 of Installing a Memory Upgrade Module. 2 Pull the clips sideways away from each side of the memory upgrade module at the same time. 3 While holding the clips out, remove the module from the slot by lifting it up and pulling it away from your notebook. 4 Store the memory upgrade module in a static guarded sleeve. 5 Replace the cover and reinstall the screws. Memory Clip Figure 35.
Device Ports Your Fujitsu LifeBook notebook and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, printers, etc. Internal LAN (RJ-45) Jack The internal LAN (RJ-45) jack is used for a Gigabit (10Base-T/100Base-Tx/1000Base-T) Ethernet LAN connection. You may need to configure your notebook to work with your particular network. (Contact your network administrator for information on your network configuration.
Figure 37. Connecting a USB Device to System (rear and right side) Headphone Jack The headphone jack allows you to connect headphones or powered external speakers to your notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: 1 2 Align the connector with the port opening. Push the connector into the port until it is seated. Figure 38.
Microphone Jack The microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your notebook. In order to connect a microphone follow these easy steps: 1 2 Align the connector with the port opening. Push the connector into the port until it is seated. Figure 39. Connecting Microphone External Video Port The external video port allows you to connect an external monitor or LCD projector.
PRESSING THE [FN] + [F10] KEYS ALLOWS YOU TO CHANGE YOUR SELECTION OF WHERE TO SEND YOUR DISPLAY VIDEO. EACH TIME YOU PRESS THE KEY COMBINATION, YOU WILL STEP TO THE NEXT CHOICE, STARTING WITH THE BUILT-IN DISPLAY PANEL ONLY, MOVING TO THE EXTERNAL MONITOR ONLY, FINALLY MOVING TO BOTH THE BUILT-IN DISPLAY PANEL AND AN EXTERNAL MONITOR. IEEE 1394 Port The 4-pin 1394 port allows you to connect digital devices that are compliant with IEEE 1394 standard.
E-SATA Port E-SATA (External Serial Advanced Technology Attachment) is an external version of SATA, which connects your computer to the hard drive. E-SATA is ideal for backing up large files on an external hard drive. To connect an E-SATA device: 1 Align the connector with the port opening. 2 Push the connector into the port until it is seated. Figure 42.
Chapter 4 Troubleshooting Your LifeBook Troubleshooting There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.
7 If the problem has not been resolved, refer to the Troubleshooting Table that follows, for more detailed troubleshooting information. IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE. 8 If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) E-mail: 8fujitsu@us.fujitsu.
Specific Problems Using the Troubleshooting Table When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.
Problem Possible Cause Possible Solutions The volume is turned too low. Adjust the volume control on your notebook and operating system. Use the [Fn+F9] key combination on your keyboard. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your notebook. The software volume control is set too low. Manually adjusting the volume (i.e. keyboard "hot keys") should dynamically adjust the volume of the operating (see above).
Problem Possible Cause Possible Solutions LifeBook notebook fails to recognize DVD/CDRW/CD-ROM/Blu-ray discs. (continued) Incorrect DVD Player or no DVD Player software is installed. Install DVD Player software. (See “Media Player Software” on page 65.for more information.) Wrong drive designator was used for the disc in the application. Verify the drive designator used by the application is the same as the one used by the operating system.
Problem Possible Cause Possible Solutions The wrong drive designator was used by an application when a bootable disc was used to start the notebook. Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted. Security is set so your operating system cannot be started without a password. Verify your password and security settings. Hard Drive Problems You cannot access your hard drive.
Problem Possible Cause Possible Solutions Your memory module is not properly installed. Remove and re-install your memory upgrade module. See “Memory Upgrade Module” on page 78. You have a memory failure. Check for Power On Self Test (POST) messages. See “Power On Self Test Messages” on page 99. Memory Problems Your System Properties screen does not show the correct amount of installed memory. USB/E-SATA Device Problems You have installed a USB or E-SATA device.
Problem Possible Cause Possible Solutions The installed primary battery is completely discharged, there is no optional second battery installed or there is no Power adapter (AC or Auto/Airline) installed. Check the Status Indicator Panel to determine the presence and condition of the batteries. See “Status Indicator Panel” on page 28.Install a charged battery or a Power adapter. The battery is installed but is faulty.
Problem Possible Cause Possible Solutions Your LifeBook notebook turns off all by itself. (continued) The power management parameters are set for auto timeouts which are too short for your operating needs. Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button.
Problem Possible Cause Possible Solutions The batteries seem to discharge too quickly. (continued) You are running an application that uses a lot of power due to frequent hard drive access or optical drive access, or use of a modem, LAN PC card, Wireless LAN, or Bluetooth device. Use both the primary battery and an optional second battery and/or use a power adapter for this application when at all possible. The batteries are old. Replace the batteries.
Problem Possible Cause Possible Solutions An error message is displayed on the screen during the notebook (boot) sequence. Power On Self Test (POST) has detected a problem. See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. See “Power On Self Test Messages” on page 99. Your notebook appears to change setup parameters when you start it.
Problem Possible Cause Possible Solutions The display goes blank by itself after you have been using it. The notebook has gone into Video timeout, Sleep mode, or Saveto-Disk mode because you have not used it for a period of time. Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button.
Problem Possible Cause Possible Solutions The Display is dark when on battery power. The Power Management utility default is set on low brightness to conserve power. Press [Fn] + [F7] to increase brightness or click the battery guage, click on More power options, and select Adjust the display brightness. You have connected an external monitor and it does not display any information. Your external monitor is not properly installed. Reinstall your device. See “External Video Port” on page 83.
Power On Self Test Messages The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.
*Failure Fixed Disk n (where x=1-4) The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue.
*Stuck Key BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative. *Monitor type does not match CMOS – Run SETUP Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.
*Press to resume, to SETUP Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings. *Previous boot incomplete – Default configuration used Previous Power On Self Test did not complete successfully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also.
*System CMOS checksum bad – Default Configuration Used BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system. *System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data.
Restoring Your Pre-installed Software The Drivers and Applications Restore (DAR) DVD contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your computer configuration for use as documented below. IF YOU HAVE ACCESS TO THE INTERNET, VISIT THE FUJITSU SUPPORT WEBSITE AT HTTP://WWW.COMPUTERS.US.FUJITSU.COM/SUPPORT TO CHECK FOR THE MOST CURRENT INFORMATION, DRIVERS AND HINTS ON HOW TO PERFORM RECOVERY AND SYSTEM UPDATES.
4 In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately. 5 Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed. 6 After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system.
Determining whether Recovery and Utility is pre-loaded 1 2 Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. 3 You can also use the TrustedCore menu to determine whether the utility is pre-loaded by powering on your system then pressing the {Enter] key when the Fujitsu logo appears on the screen. The TrustedCore Menu will appear and the Recovery and Utility option will appear in the menu.
Procedure To verify/change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps: 1 Power on your system. When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear. 2 3 4 5 6 Select the Boot Menu from the TrustedCore Menu. Highlight the CD/DVD option. Insert the Recovery and Utility Disc into the drive tray. Click [OK].
• The Hard Disk Data Delete utility is used to delete all data on the hard disk and prevent the data from being reused. NOTE: Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions. • The Partition Creation utility allows you to create a D: partition or resize existing partitions on your hard disk. NOTE: Creating or resizing partitions with this utility will cause all data on the hard disk to be completely erased.
About Fujitsu Driver Update Displays the FDU version number and copyright information Fujitsu Driver Update Readme Displays the FDU readme.
Chapter 5 Care and Maintenance Caring for your LifeBook Notebook If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. • THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).
Your notebook is a durable but sensitive electronic device. Treat it with respect and care. Make a habit of transporting it in a suitable carrying case. Do not attempt to service the computer yourself. Always follow installation instructions closely. Keep it away from food and beverages. To protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris.
Cleaning your LifeBook notebook • Always disconnect the power plug. (Pull the plug, not the cord.) • Clean your LifeBook notebook with / a damp, lint-free cloth. Do not use abrasives or solvents. • Use a soft cloth to remove dust from the screen. Never use glass cleaners. • Always shut down the computer, unplug the power adapter, and remove the battery when cleaning or disinfecting the computer exterior, keyboard or LCD display. NOTE: Avoid wetting the thermal suede in all cases.
• USE OF INCORRECT CLEANERS CAN RESULT IN OPTICAL IMPAIRMENT OF THE LCD AND/OR DAMAGE TO THE COMPUTER. ALWAYS REFER TO THE CLEANER MANUFACTURER'S GUIDELINES AND MATERIAL SAFETY DATA SHEETS FOR PROPER HANDLING AND USE OF THE PRODUCTS. • NEVER USE AMMONIA, ACIDIC, OR ALKALINE CLEANERS OR ORGANIC CHEMICALS SUCH AS PAINT THINNER, ACETONE, PROPYL OR ISOPROPYL ALCOHOL, OR KEROSENE. IT MAY DAMAGE SURFACE FINISHES AND THE COATING OF THE LCD SCREEN.
Latch Key Figure 44. Removing/installing the dust filter 5 Put back the dust filter by inserting the end without latch first (positioning the keyinside first), and pushing in the filter until it latches. ALWAYS BE SURE THE DUST FILTER IS INSTALLED WHEN RUNNING YOUR SYSTEM. NOT USING THE FILTER COULD CAUSE CONTAMINATION AND POSSIBLE DAMAGE TO THE SYSTEM.
Storing your LifeBook notebook • If storing your notebook for a month or longer, turn your LifeBook notebook off, fully charge the battery, then remove and store all Lithium ion batteries. • Store your notebook and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your LifeBook. • Store your Fujitsu LifeBook in a cool, dry location.
Traveling with your LifeBook notebook • Do not transport your notebook while it is turned on. • It is recommended that you carry your notebook with you while traveling, rather than checking it in as baggage. • Always bring your System Recovery CD that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any problems. • Never put your notebook through a metal detector. Have your notebook hand-inspected by security personnel.
Batteries Caring for your Batteries • Always handle batteries carefully. • Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire. • Do not drop, puncture, disassemble, mutilate or incinerate the battery. • Recharge batteries only as described in this manual and only in ventilated areas.
Optional Floppy Disks and Drives Caring for your Floppy Disks (optional) Avoid using the floppy disks in damp and dusty locations. Never store a floppy disk near a magnet or magnetic field. Do not use a pencil or an eraser on a disk or disk label. Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC). • Do not touch the exposed part of the disk behind the metal shutter.
Caring for your Optical Drive Your optical drive is durable but you must treat it with care. Please pay attention to the following points: • The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on. • Avoid using or storing the drive where it will be exposed to extreme temperatures. • Avoid using or storing the drive where it is damp or dusty.
Chapter 6 System Specifications Specifications This section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook. Specifications of particular configurations will vary. Configuration Label The configuration label located on the bottom of your notebook contains specific information regarding the options you’ve chosen for your notebook. Following is an example configuration label.
Microprocessor Intel® Core™ 2 Duo processors (Refer to the system label to determine the speed of your processor). Chipset • Intel GM45 or Intel PM45, depending upon configuration • I/O Controller Hub 9 Mobile (ICH-9) Memory System Memory • DDR3-1066 MHz SDRAM dual-channel memory module. • Two DIMM slots; upgradeable to 4 GB of total memory (2 GB x 2). Note that when 4 MB of memory is installed in a Windows Vista system, approximately 3.
ATI Mobility Radeon ™ HD 3470 with a maximum 128 MB GDDR3 memory dedicated VRAM (up to 1.53 GB total available graphics memory using HyperMemory™ technology with 4 GB system memory, up to 1.4 GB with 3 GB system memory, and up to 896 MB with 2 GB system memory) Audio • Realtek codec ALC269 with 2-channel High Definition (HD) audio. • Headphones: Stereo headphone jack, 3.5 mm, 1 Vrms or less, minimum impedance 32 Ohms • Microphone: Stereo microphone jack, 3.
• Write: 16x CD-R, 10x CD-RW, 8x DVD-R, 4x DVD-R DL, 4x DVD-RW, 8x DVD+R, 4x DVD+R DL, 4x DVD+RW, 5x DVD-RAM Features Integrated Pointing Device Touchpad pointing device with scroll button or optional fingerprint sensor Communications • Gigabit LAN: Internal wired 10/100/1000 Gigabit Ethernet LAN Wireless LAN: • Optional Integrated Intel WiFi Link 5100 (150 Mbps Tx/300 Mbps Rx, 802.11 a/b/g+draft n) • Optional Integrated Intel WiFi Link 5300 (450 Mbps Tx/Rx, 802.
• Four USB 2.0 (Universal Serial Bus) connectors for input/output devices • One E-SATA jack • One HDMI jack • One DC In connector • One IEEE 1394 (4-pin type) jack • One LAN (RJ-45) connector • One stereo headphone jack • One stereo microphone jack Keyboard Built-in keyboard with all functions of 101 key PS/2 compatible keyboards.
Power Battery Standard Lithium ion battery, rechargeable, 6-cell 10.8V, 5200 mAh, or, High capacity Lithium ion battery, rechargeable, 8-cell, 14.4V, 5200 mAh AC Adapter Autosensing 100-240V AC, supplying 19V DC, 4.22A, 80W to the LifeBook; includes an AC cable Power Management Conforms to ACPI (Advanced Configuration and Power Interface). Dimensions and Weight Overall Dimensions Approximately 14.49"(w) x 10.43"(d) x 1.71”(h) (368 mm x 265 mm x 43.
Popular Accessories For ordering or additional information on Fujitsu accessories please visit our Web site at www.shopfujitsu.com or call 1-800-FUJITSU. Pre-Installed Software Depending on your pre-installed operating system, your notebook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. The following list indicates the software on your system.
Learning About Your Software Tutorials All operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application. Manuals Included with your notebook you will find manuals for your installed operating system and other preinstalled software. Manuals that are not included are available online through the help system of the software.
CyberLink PowerDirector CyberLink PowerDirector allows you to edit and enhance your videos, and add special effects to them. OmniPass Fingerprint Recognition Software The fingerprint sensor uses Softex OmniPass which adds password management capabilities to Windows operating systems.
Operating System Options Depending upon your system, one of the following operating system configurations will be installed: • Microsoft Windows Vista® Home Premium Edition, or, • Microsoft Windows Vista Business Edition Productivity Options Depending upon your system, one of the following productivity applications will be installed: • Microsoft® Office Ready With Office Ready PCs it's now even easier to take advantage of Microsoft Office 2007.
Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
ADSL Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines. AGP Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators. Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook notebook. BIOS Basic Input-Output System.
Byte 8 bits of parallel binary information. Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster. CardBus A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture. CD-ROM Compact disk read only memory. A form of digital data storage which is read optically with a laser rather than a magnetic head.
CRT Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam. Data The information a system stores and processes. DC Direct current. A voltage or current that does not fluctuate periodically with time. Default Value A pre-programmed value to be used if you fail to set your own. DHCP Dynamic Host Configuration Protocol.
Diskette A floppy disk in a hard housing with a shutter. DMA Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action. DMI Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals. DNS Domain Name System.
ECP Extended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices. Encryption Key (Network Key) Data encryption key used to encrypt message text and for computing message integrity checks. Data encryption protects data from unauthorized viewing. This device uses the same encryption key to encode and decode the data, and the identical encryption key is required between the sender and receiver. ESD Electro-Static Discharge.
I/O Port The connector and associated control circuits for data entering and leaving your notebook in electronic form. IDE Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit. IEEE802.11a Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands. IEEE802.11b Wireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.
IP Address An identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 1.160.10.240 could be an IP address. Within an isolated network, you can assign IP addresses at random as long as each one is unique.
KB Kilobyte. One thousand bytes. LAN Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves. LCD Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid. Lithium ion Battery A type of rechargeable battery which has a high power-time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.
Memory A repository for data and applications which is readily accessible to your LifeBook notebook’s CPU. MHz Megahertz. MIDI Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers. Modem A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line. Monaural A system using one channel to process sound from all sources.
Network name (SSID: Service Set Identifier ) When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key. NTSC National TV Standards Commission. The standard for TV broadcast and reception for the USA.
Pitch (keyboard) The distance between the centers of the letter keys of a keyboard. Pixel The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear. POST Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your notebook. Status and error messages may be displayed before the operating system is loaded.
RAM Random Access Memory. A hardware component of your LifeBook notebook that holds binary information (both program and data) as long as it has the proper power applied to it. RAM Module A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools. Reset The act of reloading the operating system. A reset erases all information stored in RAM. Restart See Reset. Resume To proceed after interruption.
Shared key authentication 802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP. If the client has the wrong key or no key, authentication will fail and the client will not be allowed to associate with the AP.
SVGA Super VGA. S-Video Super Video. A component video system for driving a TV or computer monitor. System Clock An oscillator of fixed precise frequency which synchronizes the operation of the system and is counted to provide time of day and date. TCP/IP Transmission Control Protocol/Internet Protocol. A standard Internet protocol that is most widely used.
WFM Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility. Wi-Fi Compatible Wi-Fi (Wireless Fidelity) Identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guarantees the interoperability of wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA Web site at: www.
Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations. CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.
Appendix A: WLAN User’s Guide FCC Regulatory Information Please note the following regulatory information related to the optional wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
FCC Radio Frequency Exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the Wireless LAN antenna (located on the top edge of the LCD screen) and your body. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.
Before Using the Optional Wireless LAN This manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference. BEFORE USING THE WIRELESS LAN DEVICE, YOU MUST FIRST INSTALL CLICKME! TO ENSURE THAT THE CORRECT SOFTWARE FOR YOUR DEVICE IS INSTALLED.
Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).
How to Handle This Device The WLAN device is an optional device that may come pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Operating System that your mobile computer comes with has been pre-configured to support the WLAN device. • Intel WiFi Link 5100 and 5300 devices support IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n (draft). • The WLAN device operates in the 2.
Deactivation Using the Wireless On/Off Switch The WLAN device can be deactivated quickly and efficiently by toggling the Wireless On/Off Switch to the Off position. The Wireless On/Off switch has no effect on non-Wireless LAN models. Wireless LAN/Bluetooth/UWB On/Off Switch Figure 45.
Configuring the Wireless LAN The optional WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows Vista. Support for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: Configuring the WLAN Using Windows Vista 1 2 Click the Start button, then select Control Panel.
Troubleshooting the WLAN Troubleshooting Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. Problem Unavailable network connection Possible Cause Possible Solution Incorrect network name (SSID) or network key Ad hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSIDs and WEP key values must be identical on each machine.
Problem Unavailable network connection (continued) Possible Cause Possible Solution The WLAN device has been deactivated or disabled Check if the wireless switch is turned On. Go to Start -> Control Panel, and double-click on Windows Mobility Center. If the wireless network is off, click the [Turn wireless on] button. The computer to be connected is turned off Check if the computer to be connected is turned ON.
WLAN Specifications Specifications Item Specification Type of network The Intel WiFi Link 5100 and WiFi Link 5300 (802.11 a/b/g + draft n) WLAN devices conform to IEEE 802.11a, 802.11b/g, and 802.11 draft-n, Wi-Fi based*. Transfer rate (Automatic switching) 54 Mbps maximum data rate (IEEE802.11n to be determined) Active frequency Typical operating distances** Number of channels • • • 802.11n (draft): 2.4 GHz or 5 GHz • • • • 802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps • • • 802.
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed. ** The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources. *** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/ 104 bits after subtracting the fixed length of 24 bits.
Using the Bluetooth Device The Integrated Bluetooth module (EYTF3CSFT) is an optional device available for Fujitsu mobile computers. What is Bluetooth Bluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located on the front edge of the right palm rest and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.
Using a UWB Device The Integrated Certified Wireless USB (UWB) module is an optional device available for Fujitsu mobile computers. What is Certified Wireless USB? Certified Wireless USB, (hereinafter WUSB), is a short range, high bandwidth RF communication protocol that is capable of sending 480 Mbps at distances up to 3 meters (approximately 10 feet) and 110 Mbps at up to 10 meters (approximately 33 feet). WUSB is designed to operate in the 3.1 GHz to 10.6 GHz RF band in the United States.
Appendix B: Fingerprint Sensor Device Introducing the Optional Fingerprint Sensor Device Your system may have an optional fingerprint sensor device below the Touchpad, between the left and right buttons. This also serves as a scroll sensor. Fingerprint Sensor Device Figure 46. Fingerprint sensor ALTHOUGH THE SYSTEM MAY HAVE A FINGERPRINT SENSOR IN PLACE OF A SCROLL BUTTON, THE FINGERPRINT SENSOR CAN BE USED FOR SCROLLING.
With a fingerprint sensor, you can avoid having to enter a username and password every time you want to: • Log onto Windows • Resume from sleep mode • Cancel a password-protected screen saver • Log into web sites that require a username and password After you have “enrolled” - or registered - your fingerprint, you can simply swipe your fingertip over the sensor for the system recognize you.
System Requirements The OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows a Windows Vista operating system and at least 35 MB available hard disk space Installing the OmniPass Application If OmniPass is already installed on your system, go to “User Enrollment” on page 169. Otherwise continue with this section on software installation.
To check the version information of OmniPass: 1 From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen), or, Click the Start button, select Settings, and click Control Panel. Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear.
User Enrollment Before you can use any OmniPass features you must first enroll a user into OmniPass. Master Password Concept Computer resources are often password-protected. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access. This can result in dozens of sets of credentials that you have to remember. During user enrollment a "master password” is created for the enrolled user.
Basic Enrollment The Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified otherwise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard. 1 Click Enroll to proceed to username and password verification.
2 It is now time for OmniPass to capture your selected fingerprint. It may take a several capture attempts before OmniPass acquires your fingerprint. Should OmniPass fail to acquire your fingerprint, or if the capture screen times out, click [Back] to restart the fingerprint enrollment process. Your system has a “swipe” fingerprint sensor. A swipe sensor is small and resembles a skinny elongated rectangle.
or hibernate, when unlocking a password-enabled screensaver, during password replacement for remembered site or application logins, and more. When you see this toolbar, OmniPass is prompting you to authenticate. The Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not.
Additional Settings for Remembering a Site When OmniPass prompts you to enter a “friendly name” you have the opportunity to set how OmniPass authenticates you to this site. There are three settings for how OmniPass handles a remembered site. The default setting is Automatically click the “OK” or “Submit” button for this password protected site once the user is authenticated.
The following cases are applicable to using OmniPass to login to: Windows, remembered web sites, and all other password protected resources. With Master Password Once you return to a site you have remembered with OmniPass, you may be presented with a master password prompt. Enter your master password and you will be allowed into the site.
OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site. The exception to the above rule is when resetting the Windows password. If your password is reset in Windows, the next time you login to Windows, OmniPass will detect the password change and prompt you to “Update” or “Reconfirm” the password with OmniPass. Enter your new Windows password in the prompt and click OK.
To set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automatically be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password". Choosing User Identity during Login To choose your identity during login, type your username in the User Name: field.
Using OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported.
The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name. OmniPass will notify you if the user was successfully imported.
• Open the Windows Control Panel (accessible via Start button -> Settings -> Control Panel) and double-click the Softex OmniPass icon. User Management The User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/Export User functionality is documented in “Exporting and Importing Users” on page 176. Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard.
System Settings The OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon. The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass.
Cannot add a User with a Blank Password to OmniPass If you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the procedure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure. Click Start, Control Panel, Administrative Tools, and Local Security Settings.
Index A BIOS guide 52 setup utility 51 Bluetooth Where to Find Information 162 Built-in Speakers 89 About This Guide 1, 13 AC adapter 46 plug adapters 116 Anti-theft lock slot 23, 25 Application Panel 41 Auto/Airline Adapter 46 Automatically Downloading Driver Updates 108 C CapsLock 30 CD-ROM 89, 90 Click Me! 54 Clicking 35 Cold-swapping 62 Configuration Label 120 Controls and Connectors 17 Conventions Used in the Guide 13 Cursor 34 Cursor Keys 32 B Battery 59 alarm 61 bay 27 care 117 cold-swapping 62 c
closing 48 latch 18 opening 47 problems 96, 97 Double-Clicking 35 Dragging 37 Drivers and Application Restore CD 104 DVD drive problems 89, 90 tray release 68 Fujitsu LifeBook storing 113, 115 traveling 116 Fujitsu Support Center 43 Function Key F10 33 F3 33 F6 33 F7 33 F8 33, 40 F9 33, 40 FN 33 E Emergency tray release 23, 25 Error Messages 99 ExpressCards 71 External Monitor Port 22, 83 H Hard Disk Drive access indicator 28, 30 problems 91 Headphone Jack 82 Hibernation Feature 57 disable/enable 57 F F
L N LAN (RJ-45) Jack 23, 25 LifeBook Application Panel configuring 44 deactivating and activating 44 launching applications 44 LifeBook Security Application Panel 19 buttons 41 configuring 41 launching applications 41 NumLk 30 O Optical Digital Audio-Out Jack 22 Optical Drive 64 P PC Card problems 92 slot 20, 21 PC Cards removing 72, 74 Power AC adapter 46 Auto/Airline adapter 46 failure 93 management 55 off 58 on 49 problems 95 sources 46 Power Management 55 Power On Self Test 49, 99 Power/Suspend/Res
S U ScrLk 30 SD Card installing 77 removing 77 SDRAM 27, 78 Secure Digital Card removing 77 Security Panel 41 Sleep Mode 55 Specifications 120 Audio 122 Chipset 121 Dimensions and Weight 125 Environmental Requirements 125 Keyboard 124 Memory 121 Microprocessor 121 Power 125 Video 121 Status Indicator Panel 18, 28 Stereo Speakers 19 Support Button 43 Universal Serial Bus Ports 81 Unpacking 16 USB 81, 92 problems 92 USB 2.
