User’s Guide Learn how to use your Fujitsu LifeBook N6470 notebook
Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.
PowerProducer, MakeDisc, PowerDVD, and PowerDirector are trademarks of CyberLink Corp. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
IMPORTANT SAFETY INSTRUCTIONS This product requires an AC adapter to operate. Use only a UL Listed I.T.E. AC Adapter with an output rating of 19V DC, with a current of 5.27A (100W)..
System Disposal Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL LAWS. Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*.
Contents Preface About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 1 Getting to Know Your LifeBook Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touchpad Pointing Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Clicking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting Your LifeBook Notebook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Hard Disk Drive Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Cards/ExpressCards™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Installing PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Installing ExpressCards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Removing ExpressCards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring Your Pre-installed Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Re-installing Individual Drivers and Applications . . . . . . . . . . . . . . . . . . . 99 Restoring the Operating System for Windows XP Systems. . . . . . . . . . . . 100 Restoring the Operating System for Windows Vista Systems . . . . . . . . . . 101 Automatically Downloading Driver Updates . . . . . . . . . . . . . . . . . . . . . . . 105 Chapter 5 Care and Maintenance Caring for your LifeBook Notebook . .
Glossary/Regulatory Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Appendix A: WLAN User’s Guide Before Using the Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Wireless LAN Modes Using this Device . . . . . . . . . . . . . . . . . . . . . . . . . . 150 How to Handle This Device . . . . . . . .
Preface About This Guide The LifeBook® N6470 notebook from Fujitsu Computer Systems Corporation provides desktop performance with a fast Intel® Core™ 2 Duo processor. The 17" Color Enhanced Crystal View WXGA+ high-resolution screen displays vibrant colors with pinpoint sharpness. The LifeBook features an ATI Mobility™ Radeon™ HD 2600 graphics chipset with 512 MB of HyperMemory™*. It comes with Microsoft® Windows Vista™ Home Premium, Windows Vista Business, or Windows Vista Ultimate pre-installed.
THE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF THE SUBJECT MATERIAL. THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR PLEASE READ ALL CAUTION INFORMATION CAREFULLY. COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR LIFEBOOK NOTEBOOK, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.
• • • • Purchase date Conditions under which the problem occurred Any error messages that have occurred Type of device connected, if any Fujitsu Shopping Online You can go directly to the online by going to the website at: www.shopfujitsu.com. YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS. To ensure that you always have the most current driver updates related to your system, you should occasionally access the Fujitsu Driver Update (FDU) utility.
Chapter 1 Getting to Know Your LifeBook Overview This section describes the components of your Fujitsu LifeBook N6470 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers. Figure 1.
Locating the Controls and Connectors Display Panel Latch Fingerprint Recognition/ Scrolling Sensor Keyboard Display Panel Status Indicator Panel Touchpad Pointing Device Stereo Speakers Visual Optimizer Button Application/Media + Volume Visual Optimizer Player Buttons Mode Internet Mail - Power/Suspend/Resume Button Volume Control Wireless LAN Switch Figure 2.
Top and Front Components The following is a brief description of your LifeBook notebook’s top and front components. Display Panel Latch The display panel latch locks and releases the display panel. Display Panel The display panel is a color LCD panel with back lighting for the display of text and graphics. Status Indicator Panel The Status Indicator Panel displays symbols that correspond with a specific component of your LifeBook notebook. See “Status Indicator Panel” on page 22.
Volume Control The Volume Control toggle allows you to increase or decrease volume manually. See “Controlling the Volume” on page 32. Wireless LAN Switch The Wireless LAN On/Off Switch turns the wireless LAN on and off. See “Appendix A: WLAN User’s Guide” on page 146. Stereo Speakers The built-in boxless dual speakers provide stereo sound. Additionally, there is a subwoofer located on the bottom of the system. See “LifeBook notebook bottom panel” on page 20.
Optical Drive Optical Drive Eject Button DC Power Jack Figure 3. LifeBook notebook left-side panel Left-Side Panel Components Following is a brief description of your LifeBook notebook’s left-side components. Optical Drive One of several different drives can be installed depending upon the configuration of your system. See “Optical Drive” on page 57.. Optical Drive Eject Button The optical drive eject button is used to eject the media tray.
Memory Stick/SD/xD Card Slot IEEE 1394 Port Headphone Jack Microphone Jack USB Port Subwoofer Speaker Air Chamber ExpressCard Eject Button ExpressCard Slot PC Card Eject Button PC Card Slot Figure 4. LifeBook notebook right-side panel Right-Side Panel Components The following is a brief description of your LifeBook notebook’s right-side components. Memory Stick/SD/xD Card Slot The Memory Stick/Secure Digital (SD)/xD card slot allows you to insert a flash memory card for data storage.
Microphone Jack The microphone jack allows you to connect an external stereo microphone. See “Microphone Jack” on page 78. USB 2.0 Ports The five USB ports (one on the right side panel and four on the rear panel) allow you to connect Universal Serial Bus (USB) 2.0 or USB 1.1 devices. See “Universal Serial Bus (USB) 2.0 Ports” on page 77..
LAN (RJ-45) Jack USB 2.0 Ports USB Port Anti-Theft Lock Slot Modem Port HDMI Port External Video Port Air Vents S-Video Out Port Figure 5. LifeBook notebook back panel Back Panel Components Following is a brief description of your LifeBook notebook’s back panel components. LAN Port The LAN port is designed to accept a Local Area Network (LAN) RJ-45 jack. See “Communications Ports” on page 74. USB 2.
Anti-theft Lock Slot The anti-theft lock slot allows you to attach an optional physical lock down device. Modem Port The modem port is designed to accept a Modem (RJ-11) telephone jack for the multi-national internal 56K modem. See “Communications Ports” on page 74. THE INTERNAL MODEM IS NOT INTENDED FOR USE WITH DIGITAL PBX SYSTEMS. DO NOT CONNECT THE MODEM TO A DIGITAL PBX AS IT MAY CAUSE SERIOUS DAMAGE TO THE INTERNAL MODEM OR YOUR LIFEBOOK NOTEBOOK.
Air Flow Vents The air flow vents assist in proper cooling of the system. TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE, BE SURE TO KEEP ALL AIR ALL VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. DO NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.
Lithium ion Battery Bay Configuration Label (approximate location) Memory Upgrade Compartment Air Vents (multiple locations) Subwoofer Figure 6. LifeBook notebook bottom panel Bottom Components The following is a brief description of your LifeBook notebook’s bottom panel components. Lithium ion Battery Bay The battery bay contains the internal Lithium ion battery.
Memory Compartment Cover Your LifeBook notebook comes with high speed DDR2-667 PC5300 SO-DIMM memory. The memory upgrade compartment allows you to expand the system memory capacity of your LifeBook notebook, thus improving overall performance. See “Memory Upgrade Module” on page 70. Subwoofer The subwoofer speaker provides bass-range sound to supplement the stereo speakers, resulting in highquality audio. Air Flow Vents The air flow vents assist in proper cooling of the system.
Battery Charging Hard Drive/Optical Drive Access Battery Status NumLock Indicator EMail Indicator ScrLock Indicator CapsLock Indicator Figure 7. Status Indicator Panel Status Indicator Panel The Status Indicator panel is located at the top of the keyboard, near the Visual Optimizer button. Within this panel are symbols that correspond to specific components of your notebook. These symbols tell you how each of those components is operating.
LED Condition Charging Status of Battery Orange, blinking Charging suspended because battery temperature too high. Off Not charging because AC adapter is not connected. Battery Status Indicator This indicator shows how much charge is available within the installed battery.
CapsLock Indicator The CapsLock indicator states that your keyboard is set to type in all capital letters. ScrLk Indicator The ScrLk indicator states that your scroll lock is active.
Keyboard Function Keys Fn Key Application Key Cursor Keys Start Key Numeric Keypad (surrounded by heavy line) Figure 8. Keyboard Using the Keyboard Your Fujitsu LifeBook notebook has an integrated 103-key keyboard. The keys perform all the standard functions of a keyboard, including the Windows keys and other special function keys. This section describes the following keys.
• Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. • Function keys: The keys labeled [F1] through [F12] are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. • Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.
Function Keys Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. Icon Keys Description [Fn+F3] Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off. [Fn+F4] Pressing [F4] while holding [Fn] will toggle the touchpad on and off.
Touchpad Pointing Device Cursor Control Left Button Fingerprint Recognition/ Scroll Sensor Right Button Figure 9. Touchpad pointing device The Touchpad pointing device is built into your notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left and right button, and an scroll sensor (which also acts as a fingerprint recognition sensor).
AN EXTERNAL MOUSE CAN BE CONNECTED TO THE USB PORTS ON YOUR LIFEBOOK NOTEBOOK AND USED SIMULTANEOUSLY WITH THE TOUCHPAD. HOWEVER, IF YOU BOOT THE SYSTEM WITH AN EXTERNAL MOUSE CONNECTED, THE TOUCHPAD WILL BE DISABLED OR ENABLED DEPENDING ON THE SPECIFICATIONS IN YOUR BIOS SETTINGS. See “BIOS Setup Utility” on page 44. Clicking Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it.
Double-Clicking Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, then immediately release it. You also have the option of performing the double-click operation by tapping lightly on the Touchpad twice. If the interval between clicks is too long, the double-click will not be executed.
Scrolling Using the scrolling sensor allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navigating through online pages. To use the scrolling sensor, move your finger forward or backward across the button to scroll up or down a page. When you have reached the desired section of the page, raise your finger. Note that you can also scroll by sliding your finger up and down the right side of the touchpad.
Volume Control Your Fujitsu LifeBook notebook has multiple volume controls which interact with each other. ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF, YOU WILL OVERRIDE THE EXTERNAL VOLUME CONTROL SETTING.
Mode Button LifeBook Application/ Media Player Button Figure 15. LifeBook Application/Media Player Panel Buttons LifeBook Application/Media Player Panel A unique feature of your LifeBook notebook is the LifeBook Application/Media Player Panel. This feature makes your LifeBook notebook more than just another notebook computer. The panel allows you to operate the optical drive as an independent audio media player or to launch applications with the touch of one button.
Mode Button Located at the left of the large LifeBook Application/Media Player button (Figure 15), this button allows you to select the function of the panel—either as an Application Launcher or a media player. When Application Launcher is selected, the mode indicator will light up. (Figure 16) When Media Player is selected, the media player indicators will light up. (Figure 17).
Configuring your Application Panel When you start your system, the LifeBook Application Panel is automatically activated. As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. To set up the panel to best suit your needs, we have provided the Application Panel Setup utility that quickly and easily helps you make the most of this valuable feature.
Play/Pause Press this button to start playing a CD or DVD starting at the beginning. While the disc is playing, press it to pause. Press it again to continue. • If you press the play button and nothing happens, there is no disc in the media player drive, you have other than a media disc in the drive, or system is not powered on. • Because of the Windows AutoPlay function, discs will start playing immediately after they are inserted if your LifeBook notebook is on.
Chapter 2 Getting Started with Your LifeBook DC Power Jack DC Output Cable AC Adapter AC Cable Figure 18. Connecting the AC Adapter Power Sources Your Fujitsu LifeBook notebook has three possible power sources: a primary Lithium ion battery, an AC adapter, or an optional Auto/Airline adapter.
Connecting the Power Adapters The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter 1 Plug the DC output cable into the DC power jack of your LifeBook notebook. 2 Plug the AC adapter into an AC electrical outlet. Connecting the Optional Auto/Airline Adapter 1 Plug the DC output cable into the DC power jack on your notebook.
Display Latch Button Display Cover Figure 19. Opening the Display Panel Display Panel Your Fujitsu LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of active-matrix technology. Opening the Display Panel 1 2 Press the Display Panel latch button in. This releases the locking mechanism, allowing you to raise the display.
Adjusting Display Panel Brightness Once you have turned on your LifeBook notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are three ways to adjust the brightness, by using the keyboard, the Power Options, or the Windows Mobility Center. Using the Keyboard Adjusting the brightness using the keyboard changes the setting only temporarily. • [Fn+F6]: Pressing repeatedly will lower the brightness of your display.
• WHEN USING AC POWER YOUR BRIGHTNESS SETTING IS SET TO ITS HIGHEST LEVEL BY DEFAULT. WHEN USING BATTERY POWER YOUR BRIGHTNESS SETTING IS SET TO APPROXIMATELY MID-LEVEL BY DEFAULT. • THE HIGHER THE BRIGHTNESS LEVEL, THE MORE POWER THE NOTEBOOK WILL CONSUME AND THE FASTER YOUR BATTERIES WILL DISCHARGE. FOR MAXIMUM BATTERY LIFE, MAKE SURE THAT THE BRIGHTNESS IS SET AS LOW AS POSSIBLE.
Starting Your LifeBook Notebook Power On Power/Suspend/Resume Button The Power and Suspend/Resume button is used to power on your LifeBook notebook, to resume from Sleep or Save-to-Disk mode or to place your notebook in Sleep or Save-to-Disk mode. (You can also use the button to power down the system by holding it down for approximately five seconds. This can be useful if the system is “hung up”. This shouldn’t be used as the normal means of shutdown, however.
DO NOT CARRY THE NOTEBOOK AROUND WITH POWER ON OR SUBJECT IT TO VIBRATION OR SHOCKS; DOING SO COULD DAMAGE THE NOTEBOOK. When you Power On your notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your notebook will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 93.
The boot sequence is executed when: • You turn on the power to your LifeBook notebook. • You restart your LifeBook notebook from the Windows Shut Down dialog box. • The software initiates a system restart; for example, when you install a new application. Hard Disk Drive Passwords To provide additional security for your data, you can assign passwords to your hard disk drive(s). This feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about accessing the utility.
The TrustedCore Menu provides shortcuts to the following menus and information screens: • BIOS Setup • Diagnostic Screen • Boot Menu • Patent Information • System Information • Continue Booting Click BIOS Setup to open the BIOS Setup Utility. The Boot Menu can also be invoked by pressing the [F12] key when the Fujitsu logo appears on the screen.
Booting the System We strongly recommend that you not attach any external devices or put a DVD/CD in your drive until you have gone through the initial power on sequence. When you turn on your LifeBook notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.
5 6 On the next screen set your time and date settings. You will next see the "Select your computer's current location" screen. Make your selection from Home, Work (Default), and Public location. 7 The "Thank you" screen follows and an offer for free Norton Internet Security is extended. Following are several screens while Windows checks the system performance. 8 Windows will then boot up for the first time.
THERE MAY BE ADDITIONAL THIRD-PARTY APPLICATIONS THAT ARE NOT INSTALLED BY THE CLICKME! UTILITY. FOR MORE INFORMATION, REFER TO YOUR GETTING STARTED GUIDE. Fujitsu Driver Update Utility Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 105.
Power Management Your LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your LifeBook notebook may be controlled from settings made in your operating system.
Your LifeBook notebook can be put in Sleep mode by: • Pressing the Power/Suspend/Resume button when your system is turned on. • Clicking the power icon on the lock menu. • Selecting Sleep from the Windows Shut Down menu. • Timing out from lack of activity. • Allowing the battery to reach the Dead Battery Warning condition.
Hibernation (Save-to-Disk) Feature The Hibernation feature saves the contents of your notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation Feature The default settings are not enabled. To enable or disable the Hibernation feature follow these steps: 1 2 From the Start menu, select Control Panel (Classic View), then select Power Options.
Power Off Before turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your notebook shuts down without error, use the Windows shut down procedure. • ALWAYS POWER OFF THE COMPUTER BEFORE TRANSPORTING AND/OR PACKAGING IT. AFTER SHUTTING DOWN THE SYSTEM, WAIT UNTIL THE STATUS LED PANEL INDICATES POWER OFF CONDITION (I.E., NO LIGHTS ARE ILLUMINATED).
Chapter 3 User-Installable Features Lithium ion Battery Your LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The rechargeable battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals, or other hazards. For information on maximizing your battery life, refer to the section entitled “Power Management” on page 49.
• DO NOT LEAVE A FAULTY BATTERY IN YOUR LIFEBOOK NOTEBOOK. IT MAY DAMAGE YOUR AC ADAPTER OR YOUR NOTEBOOK ITSELF. IT MAY ALSO PREVENT OPERATION OF YOUR NOTEBOOK BY DRAINING ALL AVAILABLE CURRENT INTO THE BAD BATTERY. • UNDER FEDERAL, STATE, OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTING THEM IN THE TRASH. PLEASE TAKE CARE OF OUR ENVIRONMENT AND DISPOSE OF BATTERIES PROPERLY. CHECK WITH YOUR LOCAL GOVERNMENT AUTHORITY FOR DETAILS REGARDING RECYCLING OR DISPOSING OF OLD BATTERIES.
USING HEAVY CURRENT DEVICES SUCH AS THE MODEM OR FREQUENT DVD/CD-RW/CD-ROM ACCESSES MAY PREVENT CHARGING COMPLETELY. Low Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your LifeBook notebook will go into Sleep mode. There is no guarantee that your data will not be lost once the notebook reaches this point.
Shorted Batteries The Status Indicator panel displays the battery status via the Battery Status indicator to show the charge level available in that battery. If the display is flashing red, it means that the battery is damaged and must be replaced so it does not damage any other parts of your LifeBook notebook. Replacing the Battery By purchasing an additional battery, you can have a fully charged spare to swap with a discharged battery.
Media Holder Tray Media Tray Eject Button Figure 23. Optical Drive Optical Drive Your Fujitsu LifeBook notebook contains an optical drive which is either a Dual-Layer Multi-Format DVD Writer or a Blu-ray™ DVD-ROM player. Optical Drive Media Dual-Layer Multi-Format DVD Writer model only: With this drive, you can play CD-ROM, CD-R, CDRW, DVD-ROM, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW, DVD-RAM discs, and record CD-R, CD-RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW, DVDRAM discs.
• PRIOR TO USING YOUR OPTICAL DRIVE, YOU MUST INSTALL THE OPTICAL PLAYER SOFTWARE. REFER TO THE APPLICABLE README FILE ON THE DRIVER APPLICATIONS CD-ROM FOR INSTRUCTIONS ON INSTALLING YOUR OPTICAL PLAYER SOFTWARE. • YOU SHOULD PERIODICALLY CHECK THE FUJITSU WEBSITE AT: US.FUJITSU.COM/COMPUTERS FOR CURRENT UPDATED DRIVERS. • PROLONGED USE OF THE OPTICAL DRIVE, SUCH AS WATCHING A DVD MOVIE, WILL SUBSTANTIALLY REDUCE YOUR BATTERY LIFE.
a. b. c. d. Figure 24. Loading Media Removing Media 1 Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the notebook a short distance. 2 3 4 Gently pull the tray out until the disc can easily be removed from the tray. Carefully remove the media disc from the holder tray. Gently push the holder tray back in until you hear a click.
Playing Media on the Optical Drive There are three ways to operate the optical drive: • Using the Optical Player Software • Using the Media Player Buttons • Using the Desktop Control Panel Using the Optical Player Software PRIOR TO USING YOUR OPTICAL DRIVE, YOU MUST INSTALL THE OPTICAL PLAYER SOFTWARE. FOR DETAILS ON USING YOUR OPTICAL PLAYER SOFTWARE, REFER TO THE SOFTWARE HELP FILE. Starting a DVD Movie 1 2 Insert the DVD into the notebook’s optical drive. If the AutoPlay feature activates, skip Step 2.
1 2 To Pause the movie, click the button. To Rewind the movie, click the button to rewind to a specific portion of the movie, or the button to return to the opening screen. 3 To Fast-forward the movie, click the button to forward to a specific portion of the movie, or the button to jump to the ending credits. 4 To Stop the movie, click the button. Exiting the Optical Player 1. Click the U in the upper right corner of the title bar.
IF YOU DON’T STOP THE OPTICAL DRIVE QUICKLY AND THE NOTEBOOK ATTEMPTS TO AUTO-SUSPEND (CRITICAL BATTERY LOW STATE) THE NOTEBOOK WILL SHUT DOWN IMPROPERLY. IF THIS OCCURS, YOU WILL NEED TO POWER THE SYSTEM UP WITH THE POWER/SUSPEND/RESUME BUTTON AND FOLLOW ANY INSTRUCTIONS THAT APPEAR. 4 Manually place your notebook into Sleep mode by depressing the Suspend button. Plug in a power adapter and replace the discharged battery with an additional fully-charged battery.
PC Cards/ExpressCards™ Your LifeBook notebook supports Type I and Type II PC Cards and ExpressCardsTM, in separate dedicated slots. With these cards you can perform a variety of functions depending on which type of card you install. You can install one or two cards at a time, depending on its type. PC Cards should be installed in the bottom slot and ExpressCards in the top slot.
• INSTALLING OR REMOVING A PC CARD DURING YOUR LIFEBOOK NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK NOTEBOOK. • DO NOT INSERT A PC CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, THE NOTEBOOK, OR BOTH. 1 See your PC Card manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.
Installing ExpressCards There are two different width ExpressCards: 34 mm and 54 mm ("ExpressCard 34" and "ExpressCard 54"). (Figure 27). The connector inside the slot is located on the left-hand side of the slot. If you insert a 34 mm card, be sure to align it with the left side of the slot when inserting it. 34 mm 54 mm Figure 27. ExpressCard Sizes ExpressCards are installed in the ExpressCard slot (the top slot). (Figure 28) ExpressCard ExpressCard Eject Button ExpressCard Slot Figure 28.
• INSTALLING OR REMOVING AN EXPRESSCARD DURING YOUR NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR NOTEBOOK. • DO NOT INSERT AN EXPRESSCARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR NOTEBOOK, OR BOTH. • WHEN YOU RECEIVE YOUR SYSTEM, THERE MAY BE A PLASTIC SLOT PROTECTOR INSTALLED IN THE EXPRESSCARD SLOT.
Memory Stick or Memory Stick PRO Secure Digital (SD) Card xD Picture Card Memory Stick/SD/xD Card Slot Figure 29. Installing a Memory Stick or SD Card Memory Stick/Secure Digital/xD Card Slot Your LifeBook notebook supports the following memory cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.
■ SOME OF THE MEDIA IN THE ABOVE LIST MAY HAVE MORE FEATURES THAN OTHERS. ■ COPYRIGHT PROTECTION TECHNOLOGY CANNOT BE USED. ■ MULTIMEDIA CARDS (MMC) AND SECURE MMC ARE NOT SUPPORTED. Memory Stick is a flash memory technology developed by Sony. Memory Stick allows you to record, transfer and share digital content, such as digital pictures, music, movies, voice, and computer data and applications. Secure Digital (SD) Cards are very similar to Memory Sticks, but they are shorter.
1 2 3 4 5 See your Memory Stick, SD Card, or xD Card manual for instructions on the insertion of your card. Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD/xD Card. Insert the card in an adapter, if required. Insert your card into the slot with the product label facing up. Push the card firmly into the slot until it is seated in the connector.
Memory Upgrade Module Your notebook has two memory slots, and the system comes with 1 GB, 2 GB, or 4 GB of factory-installed memory. If you have a module installed in only one slot, you can increase your memory capacity by installing another memory module in the empty slot or by increasing the size of the single installed module. In order to optimize the dual-channel design, modules of equal capacity should be used. The minimum amount of memory in your system is 1GB.
Installing a Memory Module 1 Turn off power to your LifeBook notebook and remove any power adapter. 2 Make sure that all the connector covers are closed. 3 Turn the LifeBook notebook bottom side up, with the front panel toward you. 4 Remove the screws at the front of the memory upgrade module compartment. (Figure 31) 5 Remove the cover by tilting the front edge up, then pulling forward until the tabs on the cover are free. 6 Remove the memory upgrade module from the static guarded sleeve.
THE MEMORY UPGRADE MODULE IS NOT SOMETHING YOU SHOULD ROUTINELY REMOVE FROM YOUR NOTEBOOK. ONCE IT IS INSTALLED, YOU SHOULD LEAVE IT IN PLACE UNLESS YOU WANT TO INCREASE SYSTEM MEMORY CAPACITY. Removing a Memory Upgrade Module 1 Perform steps 1 through 5 of Installing a Memory Upgrade Module. 2 Pull the clips sideways away from each side of the memory upgrade module at the same time.
The amount of memory displayed should be approximately the total of all memory modules installed. There may be a discrepancy which is allocated for fixed video memory. IF THE TOTAL MEMORY DISPLAYED IS INCORRECT, CHECK THAT YOUR MEMORY UPGRADE MODULE IS PROPERLY INSTALLED. (IF THE MODULE IS PROPERLY INSTALLED AND THE CAPACITY IS STILL NOT CORRECTLY RECOGNIZED, SEE TROUBLESHOOTING ON PAGE 80.
Device Ports Your LifeBook notebook comes equipped with multiple ports to which you can connect an external device including disk drives, keyboards, modems, printers, etc. Communications Ports Your LifeBook has a Modem jack (RJ-11) and a LAN jack (RJ-45) to accommodate external communications. Modem (RJ-11) Telephone Jack The modem (RJ-11) telephone jack is used for your internal modem. To connect the telephone cable follow these easy steps: (Figure 34) 1 2 3 Align the connector with the port opening.
The modem sound is deactivated by default, to activate modem sound follow these easy steps: 1 2 3 4 5 6 Select [Start] > Control Panel. Select Classic View in the left pane. Double-click Phone and Modems. You may initially need to enter your area code in order to open the Phone and Modem Options window. Select the Modems tab, and click the [Properties] button.
IEEE 1394 Jack The 4-pin IEEE 1394 (Firewire) jack is a high-speed interface (400 Mbps) that can be used to transfer large amounts of data between your notebook and a Firewire peripheral such as a digital camera, external hard drive, or video camera. Hot-swappable and plug-n-play, it is much faster than USB 1.1, CardBus, or parallel port. To connect a 1394 device, follow these steps: (Figure 36) Figure 36. IEEE 1394 Interface THE 1394 PORT IN THIS SYSTEM USES A FOUR-PIN CONFIGURATION.
HDMI Port The High-Definition Multimedia Interface (HDMI) port is a digital audio/video interface over which uncompressed streams can be transmitted. HDMI is used to connect compatible digital devices with your computer (such as bigscreen TVs and high-end digital cameras and video recorders). To connect an HDMI device: 1 2 Align the connector with the port opening. Push the connector into the port until it is seated. Figure 37. HDMI Interface Universal Serial Bus (USB) 2.
S-Video Out Port The S-Video port allows you to connect and use directly any S-Video device, such as a VCR or television. The S-Video standard provides for a higher quality picture than Composite. In order to connect an S-Video device, follow these easy steps: (Figure 39) 1 2 Align the connector with the port opening. Push the connector into the port until it is seated. Figure 39. S-Video Jack Microphone Jack The microphone jack allows you to connect an external stereo microphone.
• THERE ARE SEVERAL TYPES OF CABLES FOR CONNECTING A DIGITAL ELECTRONIC DEVICE TO THE DIGITAL AUDIO-OUT CONNECTOR, DEPENDING ON THE CONNECTOR TYPE. THE CONNECTOR ON YOUR COMPUTER IS A OPTICAL MINI PLUG (3.5MM DIAMETER MINI PLUG) • THE FREQUENCY OF DIGITAL SOUND OUTPUT FROM THE SPDIF OUTPUT CONNECTOR IS SELECTABLE AS 48.0 KHZ OR 44.1 KHZ. IF A SAMPLING RATE CONVERTER IS NOT INSTALLED IN YOUR DIGITAL ELECTRONIC DEVICE (E.G., MD PLAYER), RECORDING IS NOT POSSIBLE.
Chapter 4 Troubleshooting Your LifeBook Troubleshooting There may be occasions when you encounter setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some straightforward issues and identify failures that require service.
IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE. 8 If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) E-mail: 8fujitsu@us.fujitsu.com Web site: http://www.computers.us.fujitsu.com/support.
Specific Problems Using the Troubleshooting Table When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.
Problem Possible Cause Possible Solutions The volume is turned too low. Adjust the volume control on your notebook and operating system. Use the [Fn+F9] key combination on your keyboard. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your notebook. The software volume control is set too low. Manually adjusting the volume (i.e., using the Volume button or keyboard "hot keys") should dynamically adjust the volume of the operating (see above).
Problem Possible Cause Possible Solutions LifeBook notebook fails to recognize DVD/CDRW/CD-ROM’s. Wrong drive designator was used for the disc in the application. Verify that the drive designator used by the application is the same as used by the operating system. When the OS is booted from a DVD/CD, drive designators are automatically adjusted. (continued) DVD/CD-RW/CD-ROM is dirty or defective. Wipe the disc with a non-abrasive CD cleaning cloth and reinsert.
Problem Possible Cause Possible Solutions You have installed an external keyboard or mouse, and it does not seem to work. Your external device is not properly installed. Re-install your device. See “Device Ports” on page 74. Your operating system software is not set up with correct software driver for that device. Check your device and operating system documentation and activate the proper driver. Your operating system software is not setup with correct driver.
Problem Possible Cause Possible Solutions The device is not properly installed. Remove and re-install the device. See “Device Ports” on page 74. The device may have been installed while an application was running, so your notebook is not aware of its installation. Close the application and restart your notebook. Your device may not have the correct software driver active. See your software documentation and activate the correct driver. USB Device Problems You have installed a USB device.
Problem Possible Cause Possible Solutions The installed primary battery is completely discharged, there is no optional second battery installed or there is no Power adapter installed. Check the Status Indicator Panel to determine the presence and condition of the batteries. See “Status Indicator Panel” on page 22. Install a charged battery or a Power adapter. The primary battery is installed but is faulty. Use the Status Indicator panel to verify the presence and condition of the batteries.
Problem Possible Cause Possible Solutions Your LifeBook notebook turns off all by itself. (continued) You are operating on battery power and ignored a low battery alarm until the battery is at the dead battery state and the system has gone into Dead Battery Suspend mode. Install a power adapter and then push the Power/Suspend/Resume button. See “Power Sources” on page 37. You have a battery failure.
Problem Possible Cause Possible Solutions The batteries seem to discharge too quickly. The power savings features may be disabled. Check the Power Options menu settings and adjust according to your operating needs. (continued) The brightness is turned all the way up. Turn down the brightness adjustment. The higher the brightness the more power your display uses. The batteries are very old. Replace the batteries. The batteries have been exposed to high temperatures. Replace the batteries.
Problem Possible Cause Possible Solutions An error message is displayed on the screen during the notebook (boot) sequence. Power On Self Test (POST) has detected a problem. See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. See “Power On Self Test Messages” on page 93. Your notebook appears to change setup parameters when you start it.
Problem Possible Cause Possible Solutions The notebook turned on with a series of beeps and the built-in display is blank. Power On Self Test has detected a failure which does not allow the display to operate. Contact your support representative. The display goes blank by itself after you have been using it. The notebook has gone into Video timeout, Standby mode, or Saveto-Disk mode because you have not used it for a period of time.
Problem Possible Cause Possible Solutions The application display uses only a portion of your screen and is surrounded by a dark frame. You are running an application that does not support the system’s native pixel resolution and display compression is enabled. Display compression gives a clearer but smaller display for applications that do not support 8native pixel resolution.
Power On Self Test Messages The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.
*Failure Fixed Disk n (where x=1-4) The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue.
*Stuck Key BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative. *Monitor type does not match CMOS – Run SETUP Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.
*Previous boot incomplete – Default configuration used Previous Power On Self Test did not complete successfully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power and contact your support representative.
*System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs. nnnn System Memory Passed Where nnnn is the amount of system memory in kilobytes successfully tested. *System timer error The timer test failed. The main clock that operates the computer is faulty.
• FAX • RING (This means an incoming call.) • BUSY • NO ANSWER When using the internal modem with applications that are not factory installed refer to the application documentation.
Restoring Your Pre-installed Software The Drivers and Applications Restore (DAR) CD contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your computer configuration for use as documented below. IF YOU HAVE ACCESS TO THE INTERNET, VISIT THE FUJITSU SUPPORT WEBSITE AT HTTP://WWW.COMPUTERS.US.FUJITSU.COM/SUPPORT TO CHECK FOR THE MOST CURRENT INFORMATION, DRIVERS AND HINTS ON HOW TO PERFORM RECOVERY AND SYSTEM UPDATES.
4 In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately. 5 Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed. 6 After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system.
1 Power on your system. When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear. 2 3 4 Select the Boot Menu from the TrustedCore Menu. Highlight the CD/DVD option, then click [OK]. Insert the Recovery and Utility Disc into the drive tray. After the system boots, follow the instructions that appear to restore your operating system, erase all data from your hard disk, or create or resize partitions on the hard disk.
Determining whether Recovery and Utility is pre-loaded 1 2 Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. 3 You can also use the TrustedCore menu to determine whether the utility is pre-loaded by powering on your system then pressing the [Enter] key when the Fujitsu logo appears on the screen. The TrustedCore Menu will appear and the Recovery and Utility option will appear in the menu.
BOOT Priority Change Before restoring an image, you must first verify that the system is set up to boot from the optical drive. To verify/change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps: 1 Power on your system. When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear. 2 3 4 Select the Boot Menu from the TrustedCore Menu.
Recovery and Utility tabs Diagnostics tab: The Diagnostics tool is designed for use by IT professionals. It is not likely you will need to use this tool. When you select devices from the Diagnosis window then click [Execute], several tests are performed on the selected components. Recovery tab: The Recovery tab contains the Start Recovery tool. Note that the recovery process erases all data from the C: drive. If you decide to use the recovery tool, be sure to back up all data that you don’t want to lose.
Automatically Downloading Driver Updates Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one).
Chapter 5 Care and Maintenance Caring for your LifeBook Notebook If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. • THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).
• Your LifeBook notebook is a durable but sensitive electronic device. Treat it with respect and care. • Make a habit of transporting it in a suitable carrying case. • Do not attempt to service the computer yourself. Always follow installation instructions closely. • Keep it away from food and beverages. • To protect your notebook from damage and to optimize system performance, be sure to keep all air vents unobstructed, clean, and clear of debris.
Cleaning your LifeBook notebook • Always disconnect the power plug. (Pull the plug, not the cord.) • Clean your LifeBook notebook with / a damp, lint-free cloth. Do not use abrasives or solvents. • Use a soft cloth to remove dust from the screen. Never use glass cleaners. • Always shut down the computer, unplug the power adapter, and remove the battery when cleaning or disinfecting the computer exterior, keyboard or LCD display. NOTE: Avoid wetting the thermal suede in all cases.
Disinfecting LifeBook computers • Wipe the surface with a soft cloth wipe and a 50% ethanol solution or use another ethanol-based germicide which has been registered as a hospital disinfectant by the EPA. • USE OF INCORRECT CLEANERS CAN RESULT IN OPTICAL IMPAIRMENT OF THE LCD AND/OR DAMAGE TO THE COMPUTER. ALWAYS REFER TO THE CLEANER MANUFACTURER'S GUIDELINES AND MATERIAL SAFETY DATA SHEETS FOR PROPER HANDLING AND USE OF THE PRODUCTS.
Traveling with your LifeBook notebook • Do not transport your notebook while it is turned on. • It is recommended that you carry your notebook with you while traveling, rather than checking it in as baggage. • Always bring your System Recovery CD that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any problems. • Never put your notebook through a metal detector. Have your notebook hand-inspected by security personnel.
Batteries Caring for your Batteries • Always handle batteries carefully. • Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire. • Do not drop, puncture, disassemble, mutilate or incinerate the battery. • Recharge batteries only as described in this manual and only in ventilated areas.
Media Care Caring for your Media (DVD/CD/CD-R) Media discs are precision devices and will function reliably if given reasonable care. • Always store your media disc in its case when it is not in use. • Always handle discs by the edges and avoid touching the surface. • Avoid storing any media discs in extreme temperatures. • Do not bend media discs or set heavy objects on them. • Do not spill liquids on media discs. • Do not scratch media discs. • Do not get dust on media discs.
• Avoid using or storing the drive near magnets or devices that generate strong magnetic fields. • Avoid using or storing the drive where it will be subjected to shock or vibration. • Do not disassemble or dismantle the optical drive. • Use of a commercially available lens cleaner is recommended for regular maintenance of your drive. PC/ExpressCards Caring for your Cards PC/ExpressCards are durable, but you must treat them with care.
Chapter 6 System Specifications Specifications This section provides the general hardware and environmental specifications for your LifeBook notebook. Specific details about your system may vary from those referenced here. For an updated list of current configurations, please go to the Fujitsu Computer Systems Corporation Website at: us.fujitsu.com/computers. ALL OPTIONS LISTED ARE ACCURATE AS OF THE DATE OF PRINT; SUBSTITUTIONS MAY HAVE BEEN MADE SUBSEQUENT TO DATE OF PUBLICATION.
. Part Number Configuration ID No: A4Axxxxxxxxxxx Part No: FPC0xxxxxxxxxxxxx N6470, 17WXGA+, T7250, VHP, DL S-MULTI, 1GB, 320G, MDM/LAN, WLAN Model # Processor Screen Size Media Drive Operating System Hard Drive Memory Communications Figure 41. Configuration Label Microprocessor Intel® Core™ 2 Duo processor. To determine the type and speed of your processor, right-click My Computer, select Properties, then select the General tab, or check the configuration label.
Video • Built-in 17" Color Enhanced Crystal View flat-panel Wide XGA+ TFT active matrix Crystal View (high contrast: 600:1 contrast ratio; high brightness: 370 nits) LCD display with simultaneous display capability. • Visual Optimizer button to dynamically and automatically enhance video images for optimal quality. Video Color and Resolution • Internal: WXGA+, 1440 x 900 pixel resolution, 16M colors max • External: 1600 x 1200 pixel resolution, 16M colors.
Mass Storage Devices Hard Disk Drives • Optional second hard disk drive (Note that the optional second hard disk drive is a factory-installed option, and cannot be purchased as an accessory.
Biometric Security Fingerprint recognition sensor helps to guard against unauthorized system access. Communications • Integrated Broadcom 10 Base-T/100 Base-TX/1000 Base-T Gigabit Ethernet LAN • Internal V.90 standard 56K* fax/modem (ITU V.90, 56K data, 14.4K fax). • Intel® Wireless Wi-Fi Link 4965AGN (quad-mode 802.11a/b/g/draft-N) or Intel Pro/Wireless 3945ABG Network Connection (802.11a/b/g) * Actual data transfer rate over U.S.
Keyboard Built-in keyboard with all functions of 103 key keyboards. • Total number of keys: 103 • Function keys: 12, [F1] through [F12] • Feature extension key: [Fn] • Windows keys: 2 (Start key and Application key) • Key pitch: 19 mm • Key stroke: 3.0 mm • Dedicated ten-key numeric keypad • Built-in Alps Wide Touchpad pointing device with left and right buttons and scrolling button External Keyboard and Mouse Support USB-compatible Management Standard DMI 2.0-ready, WFM 2.
Dimensions Overall Dimensions 15.87" x 11.61" x 1.79"/2.02" (403 mm x 295 mm x 45.5/51.3 mm) Weight Non-TV tuner model (with one hard disk drive): Approximately 9.92 lbs. (4.5 Kg) TV tuner model (with one hard disk drive): Approximately 10.12 lbs. (4.59 Kg) TV tuner model (with two hard disk drives): Approximately 10.58 lbs. (4.
• Adobe Reader • EverNote • Fujitsu Driver Update utility • Google Desktop • Google Tool Bar • Google Picasa • LifeBook Application Panel • Roxio Easy Media Creator • OmniPass Fingerprint Recognition Utility • Symantec Norton Internet Security 2007 (90-day free trial). • CyberLink MakeDisc • CyberLink PowerProducer/PowerDirector • CyberLink PowerDVD • Microsoft Works 9.
Learning About Your Software Tutorials All operating systems and most application software have tutorials built into them. We recommend that you step through the tutorial before you use an application. Manuals Included with your notebook you will find manuals for your installed operating system and other preinstalled software; some of the manuals may be installed in the applications Help menu. We recommend that you review these manuals for general information on the use of these applications.
Google Picasa Google Picasa lets you to search for, locate, move and label all of the photos on your computer. LifeBook Application Panel Software Your LifeBook is pre-installed with software utilities that let you operate and configure your LifeBook Application Panel. The Application Panel utilities are found under the Control Panel > Application Panel. Roxio Easy Media Creator Easy Media Creator allows you to easily burn CDs and edit and share photos, music, data, and videos.
CyberLink PowerDVD PowerDVD from CyberLink is a versatile DVD player software application. PowerDVD provides highquality video and audio playback on your system. Operating System Options Depending upon your system, one of the following operating system configurations will be installed: Microsoft Windows Vista Home Premium Edition With Microsoft Works 9.
Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
ADSL Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines. AGP Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators. Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook notebook. BIOS Basic Input-Output System.
Bus An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook. Byte 8 bits of parallel binary information. Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster. CardBus A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.
COM Port Abbreviation for communication port. This is your serial interface connection. Command An instruction which you give your operating system. Example: run a particular application or format a floppy disk. Configuration The combination of hardware and software that makes up your system and how it is allocated for use. CRT Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen.
DIMM Dual-in-line memory module. Disk A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette. Disk Drive The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk. Diskette A floppy disk in a hard housing with a shutter. DMA Direct Memory Access.
DOS Disk Operating System (MS-DOS is a Microsoft Disk Operating System). Driver A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment. DVMT Dynamic Video Memory Technology. A video memory architecture that increases the efficiency of the motherboard by using innovative memory utilization and direct AGP.
Floppy Disk A spinning platter of magnetic data storage media which is highly flexible. GB Gigabyte. One billion bytes. Hard drive A spinning platter of magnetic data storage media where the platter is very stiff. I/O Input/Output. Data entering and leaving your notebook in electronic form. I/O Port The connector and associated control circuits for data entering and leaving your notebook in electronic form. IDE Intelligent Drive Electronics.
IEEE802.11g Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11g devices operate in the 2.4 GHz ISM band. Infrared Light just beyond the red portion of the visible light spectrum which is invisible to humans. Infrastructure A name of a wireless LAN configuration. This type of communication uses an access point. Another type of communication is called Ad Hoc. IP Address An identifier for a computer or device on a TCP/IP network.
IR An abbreviation for infrared. IrDA Infrared Data Association. An organization which produces standards for communication using infrared as the carrier. IRQ Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed. KB Kilobyte. One thousand bytes. LAN Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.
MAC Address Media Access Control Address. A unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards. For Ethernet, frames are sent and received based on this address. MB Megabyte. One million bytes.
MTU Maximum Transmission Unit The maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large. Network key Data that is used for encrypting data in data communication.
Partition A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly. PCMCIA PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.
Program An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it. Protocol Procedures and rules use to send and receive data between computers. - Method of sending and receiving data - Process used to handle communication errors Conditions required for communication are organized in procedures for correct transfer of information. RAM Random Access Memory.
ROM Read Only Memory. A form of memory in which information is stored by physically altering the material. Data stored in this way can not be changed by your notebook and does not require power to maintain it. SDRAM Synchronous Dynamic Random Access Memory. Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data. Shared key authentication 802.
Status Indicator A display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard. Stereo (audio) A system using two channels to process sound from two different sources. Subnet mask TCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address.
TFT Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually. UL Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices. USB Universal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer. VRAM Video Random Access Memory.
Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC Notices Notice to Users of Radios and Television This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Notice to Users of the US Telephone Network This equipment complies with Part 68 of FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this information or number must be provided to the telephone company.
If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs.
Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations. Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility.
Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique. AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.1B.
Appendix A: WLAN User’s Guide FCC Regulatory Information Please note the following regulatory information related to the optional wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
FCC Radio Frequency Exposure statement This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant with the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits.
Before Using the Wireless LAN This manual describes the procedures required to properly set up and configure the integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference.
Wireless LAN Modes Using this Device Ad Hoc Mode (See Figure A-1) "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-topeer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
Access Point (Infrastructure) Mode (See Figure A-2) Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g.
How to Handle This Device The WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Operating System that your mobile computer comes with has been pre-configured to support the WLAN device. • The Intel PRO/Wireless 3945ABG WLAN device supports IEEE802.11a, IEEE802.11b and IEEE802.11g. • Intel Wireless WiFi Link 4965AGN (4965AGN) device supports IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n (draft).
Activating the WLAN Device Activation of the WLAN device can be accomplished using the same methods as the deactivation process, by using the Wireless On/Off Switch. + Volume - Wireless LAN On/Off Switch Figure A-3. Wireless LAN On/Off Switch Location Configuring the WLAN The WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows Vista. Support for most industry standard security solutions is contained in this software.
Connecting to a Network After you have configured your computer, you can connect to an active network by performing the following steps: 1 2 3 Click on the WLAN icon in the system tray. Select “Connect to a network”. Select a network from the list that appears, and click the [Connect] button.
Troubleshooting the WLAN Troubleshooting Table Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. Problem Possible Cause Possible Solution Unavailable network connection Incorrect network name (SSID) or network key Ad hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.
Problem Possible Cause Possible Solution Unavailable network connection The WLAN device has been deactivated or disabled Check if the wireless switch is turned ON. Also verify “Disable Radio” is not checked in “Network setting” window. (continued) The computer to be connected is turned off Check if the computer to be connected is turned ON.
WLAN Specifications Item Specification Type of network The Intel PRO/Wireless 3945ABG Network Connections WLAN device conforms to IEEE 802.11a and 802.11b/g (Wi-Fi based)*. The Intel PRO/Wireless 4965AGN Network Connections WLAN device conforms to IEEE 802.11a, 802.11b/g, and 802.11n (draft), Wi-Fi based* Transfer rate Active frequency Number of channels (Automatic switching) 54 Mbps maximum data rate (IEEE802.11n rates to be determined) • • • 802.11n: 2.4 GHz or 5 GHz 802.11b/g: 2400~2473 MHz 802.
Security Maximum recommended number of computers to be connected over wireless LAN (during ad hoc connection) • Encryption Types - WEP, TKIP, AES***; WPA 1.0 compliant • Encryption Keylengths Supported: 64 bits and 128 bits; 802.1x/EAP 10 units or less **** * “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.
Appendix B: Fingerprint Sensor Device Introducing the Fingerprint Sensor Device Your system has a fingerprint sensor device below the Touchpad, between the left and right buttons. This also serves as a scroll button. B-1: Fingerprint sensor ALTHOUGH THE SYSTEM HAS A FINGERPRINT SENSOR IN PLACE OF A SCROLL BUTTON, THE FINGERPRINT SENSOR CAN BE USED FOR SCROLLING. SIMPLY MOVE YOUR FINGERPRINT OVER THE SENSOR THE SAME AS YOU WOULD USE A SCROLL BUTTON.
With a fingerprint sensor, you can avoid having to enter a username and password every time you want to: • Log onto Windows • Resume from standby mode • Cancel a password-protected screen saver • Log into homepages that require a username and password After you have “enrolled” - or registered - your fingerprint, you can simply swipe your fingertip over the sensor for the system recognize you.
• The gold key-shaped OmniPass icon in the system tray at the bottom right of the screen. • The Softex program group in the Programs group of the Start menu System Requirements The OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s).
Verifying Information about OmniPass After you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system.
4 5 Follow the directions to uninstall the OmniPass application. Once OmniPass has finished uninstalling, reboot your system when prompted. User Enrollment Before you can use any OmniPass features you must first enroll a user into OmniPass. Master Password Concept Computer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access.
THE ENROLLMENT PROCEDURE ASSUMES YOU HAVE NO HARDWARE AUTHENTICATION DEVICES OR ALTERNATE STORAGE LOCATIONS THAT YOU WISH TO INTEGRATE WITH OMNIPASS. IF YOU DESIRE SUCH FUNCTIONALITY, CONSULT THE APPROPRIATE SECTIONS OF THIS DOCUMENT. Basic Enrollment The Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified otherwise, after OmniPass installation the Enrollment Wizard will launch on Windows login.
Enrolling a Fingerprint Enrolling a fingerprint will increase the security of your system and streamline the authentication procedure. You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the User Settings area. Click Enroll Authentication Device and authenticate at the authentication prompt to start device enrollment. 1 1.
Using OmniPass You are now ready to begin using OmniPass. Used regularly, OmniPass will streamline your authentications. Password Replacement You will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials. OmniPass can detect these prompts and you can teach OmniPass your login credentials.
Using the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint. Go to a site that requires a login (username and password), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login). Right-click the OmniPass system tray icon and select Remember Password from the submenu.
THIS SETTING IS MORE CONVENIENT IN THAT WHENEVER YOU GO TO A SITE REMEMBERED WITH THIS SETTING, YOU WILL BYPASS ANY AUTHENTICATION PROCEDURE AND GAIN INSTANT ACCESS TO THE SITE. BUT SHOULD YOU LEAVE YOUR SYSTEM UNATTENDED WITH YOUR OMNIPASS USER LOGGED IN, ANYONE USING YOUR SYSTEM CAN BROWSE TO YOUR PASSWORD PROTECTED SITES AND GAIN AUTOMATIC ACCESS. If you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master password or fingerprint authentication device.
Logging into Windows with a Fingerprint Device When logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.
The two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site. OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site. The exception to the above rule is when resetting the Windows password.
To set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automatically be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password". Choosing User Identity during Login To choose your identity during login, type your username in the User Name: field.
Using OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported.
exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name. OmniPass will notify you if the user was successfully imported. Things to Know Regarding Import/Export • Assume you export a local Windows User profile from OmniPass. You want to import that profile to another machine that has OmniPass.
• Open the Windows Control Panel (accessible via Start button -> Settings -> Control Panel) and double-click the Softex OmniPass icon. User Management The User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/Export User functionality is documented in “Exporting and Importing Users” on page 171. Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard.
System Settings The OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon. The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass.
Cannot add a User with a Blank Password to OmniPas If you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the procedure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure. Click Start, Control Panel, Administrative Tools, and Local Security Settings.
Index Battery Pack Lock 21 BIOS Guide 45 memory 115 setup utility 44 Boot Sequence 43 Built-in Speakers 83 A About This Guide 7 AC adapter 38, 119 plug adapters 110 Air Vents 17, 20 Application/Media Player Buttons 12 Audio 116 Auto Insert Notification 62 Auto/Airline Adapter 38 Automatically Downloading Driver Updates 105 C Cache Memory 115 CapsLock 24 CD-ROM 83, 84 Click Me! 47 Clicking 29 Color Resolution 116 Communications Port 74 Connecting the Power Adapters 38 Controls and Connectors 11 Conventions
Floppy Disk Drive 117 Fujitsu Contact Information 8 Fujitsu Driver Update utility 48, 105, 122 D DC Power Jack 19, 38 Device Ports 74, 118 Display Panel 12, 39 adjusting 40 brightness 40 closing 41 latch 12 opening 39 problems 90, 91 Double-Clicking 30 Dragging 30 Drivers and Application Restore CD 99 DVD drive problems 83, 84 H Hard Disk Drive 117 access indicator 23 problems 84 Headphone Jack 78 Hibernation Feature 51 I IEEE 1394 Port 15, 76 Integrated Pointing Device 117 K E Keyboard 25, 119 cursor
M P Media Player Care 112 Memory 115 capacity 72 compartment 21, 71 installing 71 problems 85 removing 72 upgrade module 70 Memory Stick/SD/xD Card 67 installing 68 slot 15 Microphone Jack 78 Microsoft Works 124 Modem problems 85 Modem Jack 19, 74 Modem Result Codes 97 Mouse problems 84 PC Card removing 64, 66 slot 16 PC Card Eject Button 16 Power 119 AC adapter 37 Auto/Airline adapter 37 failure 87 management 49 off 52 on 42 problems 89 sources 37 Power On Self Test 43, 93 Power/Suspend/Resume button 12
S V Save-to-Disk 51 ScrLk 24 SD Card, Installing 68 Sleep Mode 49 Specifications 114 Status Indicator Panel 12 Subwoofer 21 S-Video Out Port 19 Video 116 Video RAM 116 Visual Optimizer 36 Visual Optimizer Button 12 Volume Control 13, 32 W Warranty 9 Windows keys 26 Application key 26 Start keys 26 Windows Vista, Restoring 101 Windows XP, Restoring 100 Wireless LAN Before Using the Wireless LAN 149 Connection using Wireless Zero Tool 153 Specifications 157 Wireless LAN Glossary 155 Wireless LAN Switch 13
