User Manual

Notes
A26381-K252-Z120-4-7419
English - 3
Using the keyboard
The input and output devices (monitor, keyboard and mouse) are ergonomic in design.
Inconvenient arrangement of these devices, awkward arm movements or posture, or working with the
keyboard or mouse for lengthy periods without a break can lead to tenseness, fatigue and damage to
the locomotor system (nerves, muscles, tendons and joints). You can considerably reduce the risk of
this happening if you follow the advice given below.
•
Arrange your workplace in accordance with the recommendations for an ergonomic workstation
provided in the PC Operating Manual.
•
Position the keyboard so that you can use it without any noticeable strain. The keyboard should
be parallel to the upper part of your body. This prevents any tension in shoulders and arms.
•
When typing, hold your hands and forearms
so that they form as natural a line as
possible.
Do not turn your hands too far to the left or
right.
•
Keep your wrists straight while typing.
Do not angle your hands either up or down.
•
Do not rest your hands on the balls of your thumbs while typing, and do not strike the keys too
hard.
•
Relax your hands by occasionally taking a break from typing. During these breaks you should rest
your hands on the balls of your thumbs or place your arms on the armrests of your chair.
•
When you feel the need, do some exercises to loosen up.
Disposal and recycling
This device has been manufactured to the greatest possible degree from materials which can be
recycled or disposed of in a manner that is not environmentally damaging. The device is taken back
after use, so that it can be recycled, provided that it is returned in a condition which is the result of
normal use. Any components not recuperated will be disposed of in an environmentally acceptable
manner.
If your keyboad has a "Blue Angel" label attached
•
Siemens AG will guarantee the product for
36 months
with a
Bring-in-
Service
. The guarantee starts on the day of delivery (sale date) by
Siemens or an Siemens partner.
•
Repairs will be available for at least 5 years after the product has been
discontinued.
Notes
A26381-K252-Z120-2-7419
If you have any questions on disposal, please contact your local office, our service department, or,
directly:
Siemens AG
Recyclingcenter
Frankfurter Weg 60-62
D-33106 Paderborn
Tel.:
Fax:
+49 (0) 5251 -
81 80 10
+49 (0) 5251 -
81 80 15
CE certificate
This device complies with the re
q
uirements of the EEC directive 89/336/EEC
„Electromagnetic compatibility“.
FCC Class B Compliance Statement
If there is an FCC statement on the device, then:
The following statement applies to the products covered in this manual, unless otherwise specified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital device,
pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-Causing
Equipment Regulations. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in strict accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Siemens AG is not responsible for any radio or television interference caused by unauthorized
modifications of this equipment or the substitution or attachment of connecting cables and equipment
other than those specified by Siemens AG. The correction of interferences caused by such
unauthorized modification, substitution or attachment will be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all optional
peripheral or host devices. Failure to do so may violate FCC rules.