P3PC-E387-01XA fi-486PRRE Imprinter Operator’s Guide Operator’s Guide English Japanese
fi-486PRRE Imprinter Operator’s Guide Operator’s Guide English
INTRODUCTION Thank you for purchasing the fi-486PRRE Imprinter. The fi-486PRRE is the fi-4860C image scanner option. The fi-486PRFR and the fi-486PRRE can be installed in the fi-4860C image scanner together.However, they cannot be used at a time.Either fi-486PRRE or fi-486PRFR can be used during scanning. ATTENTION The fi-486PRRE installation should be done by a trained service engineer. fi-486PRRE The fi-486PRRE prints on the front side of documents.
. ERROR MESSAGES This chapter explains the error messages and the recovery process. 7. SPECIFICATIONS This chapter describes the specifications of the fi-486PRRE imprinter option. This manual provides necessary information to make the best use of the fi-486PRRE.
■ Revisions FCC declaration This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
International ENERGY STAR® Program As an ENERGY STAR® Partner, PFU LIMITED has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. The International ENERGY STAR® Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption.
■ Preface Safety Precautions This manual describes important details for ensuring the safe and correct use of this product. Thoroughly read this manual before you start to use this product. In particular, be sure to read and fully understand the Safety Precautions described in this manual before you use this product. Also, store this manual in a safe place so that it can be easily referred to during use of this product.
Symbols Used In This Manual This manual uses the following symbols in explanations in addition to warning indications. ATTENTION This symbol alerts operators to particularly important information. Be sure to read this information. This symbol alerts operators to helpful advice regarding operation. HINT A TRIANGLE symbol indicates that special care and attention is required. The drawing inside the triangle shows the specific caution.
■ Safety Precautions WARNING The following describes important warnings described in this manual. Do not install in locations subject to oil smoke, steam, humidity, and dust. Do not install the scanner in locations subject to oil smoke, steam, humidity, and dust. Doing so might cause fire or electric shock. Do not use the scanner if you smell strange odor.
Do not allow liquids to get inside the scanner. Do not insert or drop foreign metal objects in to the scanner. Do not scan wet document or document with paper clips. Do not splash or allow the scanner to get wet. If foreign objects (water, small metal objects, liquids, etc.) get inside the scanner, immediately press down the power button to turn off the scanner and disconnect the power plug from the power outlet. Then contact the agent where you bought the scanner or Maintenance Service Center.
CAUTION The following describes important cautions described in this manual. Protect the scanner from static electricity. Install the scanner away from strong magnetic fields and other sources of noise. Also, protect the scanner from static electricity as this might cause the scanner to malfunction. Do not use aerosol sprays near the scanner. Do not use aerosol sprays, for example, to clean the scanner.
■ Fujitsu Group Offices Please send your comments on this manual or on Fujitsu products to the following addresses: x FUJITSU COMPUTER PRODUCTS OF AMERICA, INC. 2904 Orchard Parkway, San Jose, CA 95134-2009, U.S.A. Phone: (1-800)591-5924; (1-408)432-6333 Technical Assistance Center: (1-800)626-4686 Fax: (1-408)894-1709 Website: http://www.fcpa.com/ E-mail: info@fcpa.fujitsu.com FUJITSU CANADA, INC.
FUJITSU TAIWAN LTD. 19th Fl., No39, Sec.1,Chung-hwa Rd., Taipei, Taiwan R.O.C. Phone: (886-2)2311-2255 Fax: (886-2)2311-2277 Website: http://fw.fujitsu.com/ FUJITSU HONG KONG LTD. 10/F., Lincoln House, 979 King's Road, Taikoo Place, Island East, Hong Kong Phone: (852)2827-5780 Fax: (852)2827-4724 Website: http://hk.fujitsu.com/ E-mail: scanner@fujitsu.com.hk FUJITSU SYSTEMS BUSINESS (THAILAND) LTD. 12th Fl.
Screen Examples In This Manual The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen referring to the User's Manual of the scanner application you are using.
CONTENTS 1 PREPARATIONS ........................................... 1 Checking the Contents of the Imprinter Package ..............................2 Outer View .........................................................................................3 2 BASIC OPERATIONS ................................... 5 Installing the Print Cartridge ..............................................................6 Adjusting Print Position ......................................................................
xiv
1 PREPARATIONS This chapter explains how to prepare the imprinter, fi-486PRRE for use. 1.1 Checking the Contents of the Imprinter Package ..............2 1.2 Outer View..............................................................................
1.1 Checking the Contents of the Imprinter Package Please confirm that all of the following parts are included in the package. If any parts are missing or defective, contact the FUJITSU Scanner dealer where you purchased the product. Handle the imprinter and the accessories with care. Imprinter and Accessories o Imprinter o Print Cartridge o Operator's Guide o Installation screws (Qty 2) o Positioning seal o Imprinter Cover o Imprinter Cable 2 1.
1.2 Outer View This section shows the outer view of the fi-486PRRE. Imprinter Cable Imprinter Cover 1 PREPARATIONS Imprinter Lever Print cartridge holder 1.
4 1.
2 BASIC OPERATIONS This chapter describes the installation of the Print cartridge, the adjustment of print position, and the setup of the imprinter. 2.1 Installing the Print Cartridge ................................................6 2.2 Adjusting Print Position........................................................8 2.3 Setting Imprinter....................................................................
2.1 Installing the Print Cartridge Installation of the Print cartridge is explained in the following. 1) Press the Power button on the scanner operator panel and turn off the power. 2) Remove the Imprinter cover. Imprinter cover 3) When the lever is closed, rotate the lever to open before placing the print cartridge. Tab HINT 6 Insert the cartridge with its Tab positioned toward left side and install it. 2.
4) Turn the lever on the print cartridge to fix it. 2 BASIC OPERATIONS 5) Put the Imprinter cover back. 2.
2.2 Adjusting Print Position Adjust the print position. 1) Remove the Imprinter cover. Imprinter cover 2) Place the print alignment mark to the position where you want to print. Print position sticker HINT The characters will be printed to the position of the alignment allow of print position sticker. 3) Put the Imprinter cover back. 8 2.
2.3 Setting Imprinter You must do the following: 1) Click the [Option] button is from the main screen of the scanner driver [TWAIN Driver]. 2) Select the [Imprinter(Endosor)] tab. The following screen is displayed. 2 BASIC OPERATIONS 3) Enable Imprinter. Setup the position of printing and the print string. Refer to "FUJITSU TWAIN32 scanner driver User’s Guide" stored in the scanner driver (CD-ROM) for the details of the setup. 4) Press [OK] button to confirm the setup.
10 2.
3 DAILY CARE This chapter explains how to clean the fi-486PRFR, the fi-486PRRE, and nozzle surface of the Print cartridge. CAUTION When you do the cleaning, turn off the scanner power, and unplug the power cord from the outlet. If cleaning is done with power turned on, it may cause electric shock or imprinter failure.
Clean the fi-486PRRE, and the nozzle surface of the Print cartridge. Cleaning the fi-486PRRE Ink may spatter the vicinity of the print cartridge holder. We recommend you to clean the scanner after 5000 sheets scanning to avoid smudge on the scanned image.Note that the required cleaning cycle may very depending upon document type to be scanned. More frequent cleaning may be required when printing a document on which ink does not easily get dry.
3) If the Stacker is closed, open it. 3 DAILY CARE 4) Wipe the following parts using a cloth moistened with Cleaner F1 or isopropyl alcohol. 5) Lift the Upper transport unit slightly to release the safety lock and then lower and close the transport unit slowly.
Cleaning the Nozzle Surface of the Print Cartridge Ink or stains stuck to the nozzle surface of the print cartridge or leaving the imprinter unused for a while cause poor printing of characters because of blocked emission holes in the nozzle. If your imprinter has this trouble, clean the nozzle surface of the print cartridge. ATTENTION For the cleaning, use dry lint-free cloth and wipe the parts gently. Wipe off dirt and stain gently from the nozzle surface. 1) Remove the Print cartridge.
4 REPLACING PRINT CARTRIDGE This chapter explains how to replace the Print cartridge and reset the Ink remain counter. CAUTION Make sure that you turn off the scanner power and unplug the power cable from the outlet. If the cartridge replacement is done with power turned on, it may cause electric shock or imprinter failure. 4.1 Replacing the Print Cartridge.............................................16 4.2 Reset the remaining ink counter of imprinter...................
4.1 Replacing the Print Cartridge Replace the Print cartridge and reset the Ink remain counter. 1) Press the Power button on the scanner operator panel and turn off the power. 2) Remove the Imprinter cover. Imprinter cover 3) Turn the blue lever toward right and open the cartridge holder. Tab 16 4.
4) Take out the Print cartridge from the holder and put the new one. HINT Insert the cartridge with its Tab positioned toward left side and install it. 5) Move the lever leftward to fix the cartridge. 4 REPLACING PRINT CARTRIDGE 6) Put the Imprinter cover back. 4.
4.2 Reset the remaining ink counter of imprinter If the following message comes up, prepare the new Print cartridge. If no further printing is impossible, replace the Print cartridge and reset the Ink Remain Counter. If the Print cartridge is replaced before Print cartridge error occurs, be sure to reset the Ink remain counter. P N l o e w a s R e e a a d i n n e g w ! x I x n x k x N o [XXXX] is the scanned sheet counter value. HINT 1) Press (Next button) or .
2) At , to choose to reset the ink remain counter, press arrow button) and select [Reset]. Press (Left (Enter button). Then is displayed. ! 2 6 - 1 Not to reset, select [No] and press R e s N e o To cancel the reset, select [No] and press 2 6 N e o s w I n (Right arrow button) (Enter button). (Enter button) and reset the counter ( k g g g g g g ( J J J J J ). x R x e x s x e ) t 4 / N REPLACING PRINT CARTRIDGE ! = Y (Enter button).
20 4.
5 PRECAUTION This chapter explains the important details for ensuring the correct use of the products.
1. When installing and replacing the Print cartridge, be careful not to insert the cartridge incorrectly. 2. When printing near the edge of paper, note that printing may go across the edge depending on the setting position of the imprinter. 3. Be careful not to touch the contacts or the nozzle on the bottom of the print cartridge. Poor printing or loose contact may occur 4. Do not move the imprinter during printing. Printing may be out of order. 5. Do not shock the imprinter or the print cartridge.
6 ERROR MESSAGES This chapter explains the error messages and the recovery process. If the following error messages are displayed on the LCD, the Imprinter is malfunctioning. Recover the Imprinter following the procedures described.
N o I n k C a r t r i d g e Possible causes are as follows. •Loose contact of the signal electrodes of the print cartridge. Reinsert the print cartridge in place. •Print cartridge is not installed correctly. Reinsert the Print cartridge in place. I m p r i n t e r A l a r m Possible causes are as follows. •Loose contact of the signal electrodes of the print cartridge. Reinsert the print cartridge in place. •The program memory is out of order.
7 SPECIFICATIONS This chapter describes the specifications of the fi-486PRRE imprinter option.
SPECIFICATIONS (Continued from the following page) Item Specification Printing Method Thermal inkjet printing Printed Characters Alphabet Letters : A to Z, a to z Numeric Characters : 0, 1 to 9 Symbols : !"$#%&'()*+,-./:;<=>?@[¥] ^_‘{|}¯ Maximum printable characters per line Maximum 40 column Character Size Height 2.91 mm to width 2.82 mm Character Pitch Approximately 3.
(Continued from the previous page) Item Printing Area Specification Printable area is shown as below. Reference point Printing area (rear side) Feeding direction E Center A=43mm or more B=100.5mm or less C=5mm or more D=140.5mm or less (Max.40 columm) E=5mm or more D C A ATTENTION Consumable ATTENTION A document with less than 80 mm length cannot be printed. Print Cartridge The product life of this imprinter is 5 years or 7,200,000 sheet scans whichever comes first from the date of purchase.
Purchasing consumables Contact FUJITSU Scanner dealer where you purchased the imprinter.
fi-486PRRE Operator's Guide P3PC-E387-01XA Date of issuance: August, 2002 Issuance responsibility: PFU LIMITED Printed in Japan • Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law. • The contents of this manual are subject to change without notice. • PFU LIMITED assumes no liability for incidental or consequential damages arising from the use of this manual, and any claims by a third party.