Installation guide

En-6
7.3. How to connect wiring to the terminals
Caution when wiring cable
To strip off the insulation of a lead wire, always use a special tool such as a wire stripper.
If there is no special tool, carefully strip off the insulation by using a knife or other utensil.
(1) Use ring terminals with insulating sleeves as shown in the gure to connect to the
terminal block.
(2) Securely clamp the ring terminals to the wires by using an appropriate tool so that the
wires do not come loose.
Strip : 10 mm
Ring terminal
Sleeve
(3) Connect specied wires securely, and fasten them so that there is no stress applied on
the terminals.
(4) Use a screwdriver with an appropriate bit size to tighten the terminal screws. Using of
screwdriver with inappropriate bit size will damage the screw heads, and the screws
will not be tightened properly.
(5) Do not overtighten the terminal screws. Otherwise, the screws may break.
Screw with special washer
Wire
Ring terminal
Terminal blocks
Wire
Screw with special washer
Ring terminal
(6) See the table for the terminal screw tightening torques.
Tightening torque [N·m (kgf·cm)]
M4 screw 1.2 to 1.8 (12 to 18)
CAUTION
• Match the terminal block numbers and connection cable colors with those of the
outdoor unit. Incorrect wiring may cause a re.
• Connect the connection cables rmly to the terminal block. Imperfect installation may
cause a re.
• When xing the connection cable with the cable clamp, always fasten the cable at the
plastic jacket portion, but not at the insulator portion. If the insulator is chafed, electric
leakage may occur.
• Always connect the earth (ground) wire. Improper earthing (grounding) work can
cause electric shocks.
• Do not use the earth (ground) screw for the indoor unit to the outdoor unit unless it is
specied.
8. FINISHING
(1) Insulate between pipes.
• Insulate suction and discharge pipes separately.
• For rear, right, and bottom piping, overlap the connection pipe heat insulation and
indoor unit pipe heat insulation and bind them with vinyl tape so that there is no gap.
(2) Temporarily fasten the connection cable along the connection pipe with vinyl tape.
(Wrap to about 1/3 the width of the tape from the bottom of the pipe so that water
does not enter.)
(3) Fasten the connection pipe to the outside wall with a saddle, etc.
(4) Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain
water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
(6) Check the drainage.
*Locally purchased
Pipe
Saddle*
Outside wall cap*
Sealer putty*
(Outdoors)
Wall
Overlap the insulation
Vinyl tape*
Wrap with cloth tape.
Cloth tape (accessory)
Drain hose
Pipe
Connection pipe
(heat insulation)
Indoor unit pipe
(heat insulation)
Bind the pipes together
so that there is no gap.
GOOD
Drain hose
Saddle
Lifted up Wave End in water
PROHIBITED
9. REMOVING AND REPLACING PARTS
9.1. Intake grille removal and installation
Intake grille removal
(1) Hold the intake grille with both hands at the side, then pull to the front until it becomes
hooked.
(2) Keeping the intake grille in a horizontal position, pull the mounting shaft on the left and
right to release.
Intake grille
Mounting
shaft
Mounting
shaft
Intake grille installation
(1) Attach the left and right mounting shaft in the direction of the arrow to the panel top
bearing while supporting the intake grille horizontally. Press this until it clicks so that
each shaft snaps into place.
Mounting shaft
Mounting
shaft
Bearing
Bearing
(2) Press and close the intake grille.
Press here
9.2. Front panel / control cover removal and installation
* In this description, the intake grille and wire cover already has been removed.
9.2.1. Front panel / control cover / under cover removal
(1) Remove the under covers. (Press down on the markings on the side, then slide down.)
(2) Remove the screw covers (2 places) on the bottom of the front panel, and then remove
the screws (4 places).
(3) Push down on the markings (2 places) on top of the front panel to release the hooks
(3 places), then pull the front panel towards you.
(4) Pinch the tab on the control cover to release the hook, then open.
9387603033_IM.indd 6 21/11/2018 15:03:23