Instruction Manual Head Mounted Display Wearable Keyboard 1
Unpacking and checking the device Unpack all the individual parts. If any of the parts are missing, please notify your local sales representative immediately. Below is the list of included items.
□Left belt attachment □Right belt attachment □top band □side cushion x2 □front band ■Clip to a helmet These are used when attaching HMD to a helmet.
■Wearable keyboard □wearable keyboard □AAA alkaline battery x2 □wearable keyboard belt Before using this product --------------------------------------------------------------------------------------About the warranty Be sure to fill in the necessary information on the warranty and read its contents. After that, keep it in a safe place. Be sure to have the warranty on hand whenever requesting servicing.
About the limited-life components ・The battery pack and dry cell batteries are consumable parts, so they need to be replaced on a timely basis in order to maintain performance. Furthermore, purchasing and replacing batteries must be done by yourself regardless of warranty period. ・The battery pack typically have a lifespan of between 300 and 500 cycles. Battery pack’s service life will depend on the environment temperature and usage.
compiling, or reverse assembling. 4. Limited Warranty (1) Fujitsu will not be liable in any way for any damages (including but not restricted to lost profits, work stoppages, loss of business data, or other monetary damages) that result from the use of or the inability to use the software. This also applies even if Fujitsu knew or should have known about the possibility of such damages.
Wireless LAN(Wi-Fi ®)(support IEEE802.11a/b/g/n) ・The product uses the 2.4 GHz band. DS-SS and OFDM are used as the modulation schemes. The interference distance is about 40 m or less. All bandwidths can be used, and that bands of mobile unit identification devices can be avoided.
This equipment has been tested and found to comply with the limits for a Class A digital device. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
・To use in airplane, confirm with airline company in advance. About this product ・Display is manufactured by taking advantage of highly advanced technology but some dots may always or never be lit. Note that, this shows characteristics of liquid crystal displays and not defects in the products. ・The date and time settings will be cleared if the battery pack’s power level reaches 0%. Perform the operation below to set the current time and date.
Notational conventions The meaning of the signs in this manual are described below. Indicates precaution and should not do for use. Please be sure to read the information. Indicates information related to operational points. Read when needed.
home screen is shown below. Change by tapping “Settings” → ”Date and Time” Warning and caution labels There are warning and caution labels on the product. Do not remove or damage them. Safety Precautions Before using this product, thoroughly read these safety precautions for proper use. These "Safety Precautions" describe instructions that should be observed to prevent damage to property or injury to the customer or others using the product. These instructions are divided into the following categories.
Trademarks, Copyrights and portrait rights Google, Google logo, Android, Android logo and other trademarks are trademarks or registered trademarks of Google Inc. The Bluetooth® smart ready word mark and logo are registered trademarks owned by the Bluetooth® SIG, Inc., and FUJITSU LIMITED is licensed to use these trademarks. The microSD logo, microSDHC logo are trademarks of SD-3C and LLC.
charging terminal, etc. Do not allow conductive foreign objects (metal fragments, pencil leads, etc.) to come into the contact with or get inside of these items. Doing so may cause fire or a fault. Before entering an area where flammable gas is generated, be sure to turn off the product. Do not charge the battery. Failure to do so may cause the gas to catch fire. Do not puncture the product with a nail, hit it with a hammer or step on it. Doing so may cause ignition, damage or injury.
Turn off the product when you dropped the product or the cover breaks and request a repair service. Continue to use the product in this state may cause fire or electric shock. If you hear thunder, do not touch the power plug or connect cables until you are safe. If there is a chance of a lightning strike, take off and turn off the product. If it is the AC adaptor, remove the power plug from wall outlet and disconnect cables. Lightning may cause fire, fault or damage the product as well as electric shock.
Do not use other than the AC adaptor included in the product or designated AC adaptor. Do not use the AC adaptor included in the product for other devices. Doing so may cause fire or electric shock. Do not use a cleaning spray that contains flammable chemicals to clean. Doing so may cause fire or a fault. Although the product has waterproof property, stop use if liquid such as water gets inside the product from the cap and the battery cover.
Do not use or store the product in places subject to direct sunlight or get extremely hot (e.g. in automobiles), places that get humid. Doing so may cause electric shock, fire, damage or a fault. Do not leave the product on unstable places such as shaky places or tilting surfaces. Doing so may cause injury or damage if the product is dropped. Follow the instructions on the manual to dispose the product. Check with local codes for possible special disposal instructions.
If you feel any abnormality with your skin, immediately consult a doctor for a medical treatment. Itching, rashes, eczema, etc. sometimes occurs if you use the product for a long time or depending on your physical constitution and condition. See Material List for materials used in the product. (→P.24) Use the product with the cap and the battery cover closed. If the covers are open, dirt or water may get inside causing a fault. Do not place the product directly on sand at a beach etc.
Warnings for Wi-Fi® and Bluetooth® technologies. The product should be switched off wherever you are requested to do so in ・hospitals, clinics or health care facilities Especially in the operating room for surgery, ICU, CCU, etc ・airplane if it is prohibited to use wireless technologies. ・fire alarms, automatic doors and other automatic control equipment.
If the battery pack's fluid contacts eyes, flush the eyes with clean water immediately and see a doctor right away. Do not rub the eyes. May cause loss of sight. The leaking battery pack fluid may ignite, explode or overheat. Battery pack is not waterproof. If water or seawater gets on the product, it may cause overheating, ignite, damage, electric shock or a fault. Do not charge if the battery pack is wet. If the battery pack's fluid contacts the eyes, clothes, etc., flush with clean water immediately.
its service life. Failure to do so may cause overheating, ignition, rupture or leakage. Note that the length of service life varies depending on the usage condition. Stop charging if charging takes a very long time compare to usual. Failure to do so may cause overheating, ignition, rupture or leakage. Follow the instructions on the manual to dispose the product. Check with local codes for possible special disposal instructions. A Lithium-ion battery is used in the product.
wiring apparatus beyond its rating. Also, exceeding rating, for example, by connecting multiple devices to a single power strip may result in electric shock, injuries, damage or fire. Do not short the charging jack while it is connected to the outlet. Do not touch the charging jack with a part of your body such as your hand or finger. May cause an electric shock, short, fire, injury or fault. Do not touch the battery charger for a long time while power is being supplied from an external source.
Do not strain the base of the cable by tightly wrapping the cord around the AC adaptor. Cable core may be exposed or disconnected. electric shock or fire. Doing so may result in an Do not apply a strong force by pulling the AC adaptor strongly while it is connected to the outlet. May case injury or a fault. Do not drop or apply a strong force or hard shock to it. Internal substrate might be damaged. Moreover, do not use if the AC adaptor or cable is deformed, cracked or damaged.
charger, remove the power plug from wall outlet immediately. Never use the battery charger in humid places such as bathrooms. Doing so may cause electric shock or a fault. Always remove the power plug of the battery charger from the outlet when not using it for an extended period of time. Moreover, remove AC adaptor from the battery charger. Failure to do so may cause a fire. Do not use the AC adaptor, cable or power plug if it gets damaged. May cause an electric shock or fire.
Material List Part Material Surface treatment Display panel Acrylate resin AR coating Display cushion Synthetic leather Power key, home key PC resin Exterior case PC resin + ABS resin Acrylic UV curable coating Head Mounted Display Acrylic UV curable coating microUSB connection PC resin + Polyester cap elastomer resin + silicon resin Acrylic UV curable coating microSD card slot cap PC resin + Polyester elastomer resin + silicon resin Acrylic UV curable coating Earphone connection jack cap
Knurling screw Stainless steel - Body PC resin - contacts Nickel Label polyester - Body PC resin + ABS resin - contacts Beryllium copper Battery pack Gold plating Battery charger Gold plating Wearable Keyboard body PC resin + ABS resin Acrylic UV curable coating key urethane acrylate wearable keyboard belt Styrene/ Butadiene rubber UV curable coating - microUSB connection thermoplastic cap elastomer Screw steel screw Stainless steel/ trivalent chromate coating Handling precauti
display. When it's necessary to secure the sight, move the display to below your eye. If you are not looking at the display, shift the arm to the side. ●Do not operate the product while walking, running, driving a car, motorbike or riding a bicycle. May cause an accident. ●Do not use the product in an intensely shaky or unstable. May cause dizziness, nausea, headache or motion sickness.
Bluetooth®/Wireless LAN (Wi-Fi®) function ●This product supports security features for wireless communications that are compliant with the Bluetooth® and Wi-Fi® standard specifications, but the security may not be sufficient depending on the usage environment and configuration. Be careful when making data communication using Bluetooth® or wireless LAN (Wi-Fi®) function.
[Equivalent to IPX8] IPX8 equivalent means that the product will maintain its performance as HMD with no water getting inside the main unit when the main unit is gently submerged in a tank of still tap water at room temperature to a depth of 1.0 meters and left for about 30 minutes. [Equivalent to IP5X] IP5X means a protection degree that HMD keeps functioning and safety after it is placed in a device with dust in diameter 75μ or less for 8 hours, agitated and then taken out.
●Do not open/close the cap and the battery cover if the product or your hands are wet. ●Do not use the product underwater (including button operations). ●Do not leave the product in a humid place for an extended period of time. ●The product main unit is waterproof only against fresh water and tap water (5°C to 35°C). Do not splash or soak the product into the following liquid. Do not apply or attach sand or mud to the product.
●Do not splash the product with hot water. The product is not resistant to hot temperatures. ●Use within an ambient temperature range of 5°C to 35°C and humidity range of 20% to 80%. ●Do not apply a strong water flow (more than 6 liters per minute). ●Do not drop the product. ●Do not use or leave the product under direct sunlight or in a hot place.
●When adjusting visibility, use your fingertip to pull the indent of the diopter adjustment cap to open. Please see procedure 3 in “Adjusting visibility/position” for more details. (→P.60) ●To insert/remove the battery pack, turn the battery cap counterclockwise direction to open. Please see procedure 1 in “Attaching/Removing battery pack” for more details. (→P.42) ●To attach an earphone, use your fingertip to pull the indent of the earphone connection jack cap to open shown below.
Example: microUSB connector □Rubber seals The rubber seals around the caps are important to maintain waterproofness/dustproofness. Note the following points. ●Do not remove or damage the rubber seals. ●When closing the cap, be careful not to let the rubber seals get caught. Forcibly closing the cover with the rubber seals caught may damage them resulting in loss of waterproofness/dustproofness. ●If any liquid other than fresh water and tap water (hot water, seawater, detergent, chemical, sweat, etc.
* Do not leave the connection jack without wiping off water. * In cold climates, water on the product may turn to frost. Using the product with frost may cause a fault. Do not leave the product without wiping off water. ●If the product gets wet with water or snow, wipe off with a clean dry cloth. Be careful not to get your clothes or bag get wet with water that could not be wiped off or water remaining in the gaps.
□For the keyboard Water could be collected in the microUSB connector. Open the microUSB connector cap, firmly holding the keyboard and shake it until there is no water as shown below. ■Charging precaution The battery charger is not waterproof/dustproof. Be sure to check the following points before and after charging. ●Never charge the wet battery pack.
1. Part names and functions Head mounted display 1 Hook-and-loop fastener Attach hook-and-loop fastener comes with belt attachment. 2 Display 3 Microphone 4 microphones all together. 4 Camera 5 Home button Shows the home screen 6 microUSB connector cap, microUSB connector Connect a microUSB cable. Please see “Connecting a microUSB cable” for more details. (→P.78) The battery pack cannot be charged with microUSB that is connected to the product.
When the power is on after pressing the power button, the green light will light up but lights off after a period of time. 8 Power button Following can be done by pressing the power button. Power button operation Detail of operation Press the power button once Turn ON/OFF screen Hold down the power button for few seconds Power ON/OFF Hold down the power button for more than 13 seconds Reboot Note: When there is not enough battery, the product will not boot even the power button is pressed.
1 microSD card slot cap, microSD card slot Please see microSD card for more details. (→P.77) 2 Hook-and-loop fastener Attach hook-and-loop fastener comes with belt attachment. 3 Microphone 4 microphones all together. 4 Diopter adjustment cap, diopter adjustment screw Diopter adjustment is used when the display is hard to see. Please see “adjusting visibility” when the display is hard to see. (→P.60) 5 Battery Pack Rechargeable battery pack. Please see “Charging the battery pack”. (→P.
9 Earphone connection jack cap, Earphone connection jack 10 Speaker Keyboard ■Front 1 microUSB connector cap, microUSB connector 2 [BackSpace] key 3 [Bluetooth] key 4 [Power] key Following can be done by pressing the power key. [Power] key operation Detail of operation Press the power key once Confirm remaining of dry batteries level - If the power is ON, Bluetooth/Power indicator light will be on. - If the power is OFF, Bluetooth/Power indicator light will NOT be on.
Keyboard cannot be turned ON if the microUSB is connected. Make sure to pull the cord out before turning ON. 5 Bluetooth/Power indicator light Displays status of connection or remaining of dry batteries level. Please see (→P.76) 6 One-touch button([F1]to[F3]) You can launch apps with a single action of pressing a button by pre-assigning apps to those buttons.
2. Get started Please follow the instructions how to prepare the product to be worn. Charging the battery pack The battery pack is not fully charged at the time of purchase. Charge the battery pack before using the product. The explanation below is using the AC adaptor to charge. ■Parts name of the battery charger 1 Attach the battery pack to the battery charger. Align the metal contacts of the battery pack with those of the battery charger. 2 3 4 Insert the power cable to the AC adaptor.
For microUSB, with the B engraved side facing upwards, insert the microUSB plug of the microUSB cable straight into the battery charger. Be careful not to connect the microUSB in wrong direction. It may damage the connector. - When using DC-IN connector to charge, you may charge either 2 batteries at the same time or one battery at a time using either slot A or B. - When using microUSB connector to charge, you may charge only 1 battery at a time using below equipment.
・AC adaptor with microUSB for smartphone and tablet 5 To check the status of charging The state of the battery charger indicator light will be as follows. Indicator light Status of the battery pack Lights red Charging Lights flashing - Charging timer expired If charging is not completed after the specified charging time, the indicator light flashes. Remove the battery pack and recharge it.
2 Insert the battery pack to the product. Align the metal contacts of the battery pack with those of the product. - To remove a battery pack from the product, slowly tilt the product. If tilt fast, the battery pack may pop out. 3 Align and push the battery cap as shown below.
4 Turn the battery cap clockwise direction to close. Line-up a mark on the cap and a mark on the product. Decide the orientation of the product This product can be used on both left and right eyes. Please decide which eye to see the display. The explanation in this manual is the right eye case.
To use on the left eye, 1 Move the joint with dotted-circles shown below and reverse the camera and the display positions. 2 Turn the product upside down to use on the left eye. To adjust the view, move the joint with dotted-circles shown below. Wearing the product This product is designed to be worn either directly on the head or on a helmet.
The procedures are different depending on how you wear. ■Wear on the head Please see “Assemble the fitting belt” (→P.46) ■Wear on a helmet Please see “Attach to a helmet” (→P.52) Assemble the fitting belt Assemble the fitting belt to be attached to the inner side of this product. The length of the belt can be adjusted at the end so please assemble it first as explained below. 1 Attach belt attachments and head adjusters to the product. Attach to the place where circled below.
pulling and align the holes. Positioning holes 2. Stack the right head adjuster and right belt attachment and align the positioning holes. Check to see if the positioning holes are aligned correctly. Head adjuster has an orientation so make sure the ratchet part will be on the back side. Positioning holes 3. Two places will be set with knurling screws. Use a flat blade screwdriver or a coin to turn and tighten the screws. knurled screws 4.
2 Attach the top band to the belt attachments. You may attach the top band to either side but it will be easier to adjust if the hook-and-loop fastener is on your dominant hand side. 1. 2. 3. After a side of a top band that is cut roundly is put into a hole on the belt attachment, the top band is inserted to the adjuster from the outside to the inside. The top band is inserted into the adjuster as shown in the figure and fixed.
3 4 Attach the front band to the belt attachments. 1. The front band is into a hole on the belt attachment shown below. 2. Do the same for the other side. Insert the head adjuster.
5 6 Attach the side cushions to the inner sides of the fitting belt. 1. Attach the hook-and-loop fastener on the side cushion to the belt attachment. 2. Do the same for the other side. Attach the display cushion to the display. Start attaching the display cushion to the dotted-circle shown below. Wrap the projecting part of the display with the cap part and cover with the display cushion. When covering, please don't insert the cap part inside.
This is the end of assembly. Adjust/wear HMD on your head If you wear glasses normally, keep wearing glasses and use the HMD. After wearing, please adjust the length of the band to fit your head. 1 2 Wear HMD on your head. Adjust the head band first and adjust the front band by setting the hook-and-loop fastener. 3 Adjust the ratchet on the head adjuster Adjust so that the speaker will be on top of your ear.
Continue to wear the keyboard on your arm. Please see “Attaching the keyboard”. (→P.55) Attach to a helmet You may install and use HMD on a commercially available helmet. However, some of the helmets may not be compatible with the product. 1 Attach the left and right helmet clips to the product. 1. Stack the helmet clip and the product and align the positioning holes. 2 places will be set with knurling screws.
2. 2 Do the same for the other side. Use a flat blade screwdriver or a coin to turn and tighten the screws. Loosen the screws attached to the helmet clips.
3 4 Decide where to place the product on the helmet and attach the product. If the helmet has a chin strap, put the strap inside the helmet before attaching the product. If the place to attach the product is decided, place the product into the gap of the helmet clips and tighten the screws. If the product isn't attached in the proper location of the helmet, the product may touch your ears when wearing the helmet. Attach the display cushion to the display.
5 Wear the helmet Attach the keyboard How to insert batteries and wear the keyboard to your arm is explained. 1 Slide to unlock the battery box. 2 Open the battery box cover. Place a fingertip on a tab of the battery cover on each side and pull with an angle to open.
3 Two(2) AAA alkaline batteries are placed inside from the right side. When putting the first battery, put it from the left side and slide it to the right side since there is a metal piece on the right side of the battery box. - Be careful with the orientation of the battery. - Don't mix battery types and don't mix old batteries with new batteries. 4 Close the battery cover by joining tabs and tab holes. Make sure the lock is unlocked and set it firmly.
5 Slide the lock buttons in the arrow direction shown below and close the cover. 6 Attach the keyboard belt to back of the keyboard. The hook-and-loop fastener should be face down.
7 Wear the keyboard on your arm. Wrap the keyboard belt around your arm and stick the hook-and-loop fastener. Tighten the belt so that the keyboard will not fall off.
fastener shown below. When changing the batteries for the second time, you don’t need to take the keyboard belt off. You can change the batteries as follows. 3. Initial settings Before use, initial setting by the following procedure. “Adjusting visibility/position” (→P.60) ↓ “Launch ”HMD home” screen” (→P.61) ↓ “Decide the orientation of the product” (→P.62) ↓ “Paring(connecting)” (→P.
Adjusting visibility/position 1 Hold down the power button on the product for few seconds A screen will be displayed. 2 Positon the display in front of the eye. Adjust the arm of the product so that the display will be about 3cm away from and in front of your eye. 3 Adjusting visibility 1. Use your fingertip to pull the indent of the diopter adjustment cap to open. 2. Turn the screw for visibility adjustments and adjust the focus of the screen.
- If it is hard to adjust the screw while wearing, take the product off from your head. 3. Close the diopter adjustment cap Launch ”HMD home” screen 1 Select “HMD home” in the screen. Voice command: “Number one” - You may select an item by speaking "Number [actual number]"(e.g. "Number one") when there is a number with a balloon. Please see terminology list of voice commands for words used in voice command. (→P.72) - If voice command cannot be used, you may use the keyboard.
- This screen will not appear from the second time. If you wish to display this screen, go to “settings”→”other settings”→”home”→”launcher” in “HMD home” screen. If you selected “Android home” instead of “HMD home”, this screen will appear again. “HMD home” screen will appear. ■Menu in ”HMD home” screen 1 2 3 Camera: Launch camera on the product Select file: Launch file viewer Bluetooth: connect this product and a smartphone with Bluetooth(HFP) 4 Volumes: set volume for video and notice alarms(→P.
You may select by using the keyboard if the keyboard is connected. 2 Select “Switch eye” Voice command: “Number two” 3 Select depending on your situation Voice command: “Number one”, “Number two” or “Number three”. “Automatic” will rotate the screen automatically depending on your situation.
4 Select “OK” Voice command: “Number five” Pairing(connecting) Connect the product to a smartphone and the keyboard. ■Standard configuration ■Connecting the product and a smartphone(Bluetooth) 1 Turn on the smartphone Hold down the power button. 2 In “HMD home” screen, select “Bluetooth” → “OK”.
tap “system settings”. 4 Tap “Bluetooth” Turn “ON” “Bluetooth” if it’s “OFF”. Wait until the product is recognized. 5 Tap “FHMD001” 6 In “bluetooth pairing request” screen, confirm the passkey is the same as the product and tap “pair”. Below screen will be displayed on HMD and screen will switch if connected. 7 Select “OK” on “HMD home” screen. Voice command: “number one” Bluetooth connection is complete.
- Supported profile is HFP only. - The product will not be reconnected automatically to the smartphone once the power is off or the communication is lost, even if the connection became available again. It's necessary to operate from procedure 3 above. ■Connecting the product and a smartphone(Miracast) 1 Hold down the home button until “Waiting for connection from smartphone/tablet” displays on ”HMD home” screen. 2 Turn on the smartphone Hold down the power button.
- The product will not be reconnected automatically to the smartphone once the power is off or the communication is lost, even if the connection became available again. It's necessary to operate from procedure 3 above. - Miracast connection uses 2.4GHz band wireless LAN. If you are unable to use 2.4GHz band wireless LAN or has radio wave interference, use microUSB cable for wired connection. See page “Connecting a microUSB cable” for how to connect. (→P.
5 Tap the address of the Bluetooth keyboard. It will say “connected” under the device name. Once the keyboard is connected to the smartphone, device name will be shown as “FHMD-WKB****” from the next time. Bluetooth connection is complete.
4. How to use Turning the power on The product will not be reconnected automatically to the smartphone once the power is off or the communication is lost, even if the connection became available again. For this reason, reconnection is needed before use. - Pairing is only needed during the initial settings. 1 2 Turn on the product, the smartphone and the keyboard. Display menu from the home screen of the smartphone and tap “system settings”. 3 Tap “Bluetooth” Turn “ON” “Bluetooth” if it’s “OFF”.
The smartphone screen will change to “connected” and smartphone’s screen will be displayed on the HMD screen. Miracast connection is complete. Volumes/Brightness settings ■Volume settings 1 Select “Volumes” in “HMD home” screen. Voice command: “Number four” You may select by using the keyboard if the keyboard is connected. 2 Select item and change the volume.
3 Select “OK”. Voice command: “Number five” ■Brightness settings 1 Select “Settings” in “HMD home” screen. Voice command: “Number one” You may select by using the keyboard if the keyboard is connected. 2 Select “brightness” Voice command: “Number one” 3 Select item and change the brightness. Select an item by voice command “number one”, “number two” or “number three” and use voice command “Dark” and ”Bright” to change the brightness.
if the keyboard is connected. 4 Select “OK”. Voice command: “Number five” Terminology list of voice commands You may select an item by voice command when there is a balloon displayed on the screen of the product. Please see voice command listed below.
Cancel Cancel OK OK Voice command Voice command Keyboard operation Keyboard operation Switch camera mode Switch camera mode Photo resolution Photo resolution Video resolution Video resolution Location Location Storage Storage Exit Exit Below commands are used in camera Yes Yes No No When a balloon is not displayed on the screen, you may use below voice commands and their functions.
Android home screen When this product is booted and "Android home" is chosen instead of “HMD home”, a home screen of Android of this product is displayed. This is not a smartphone’s home screen. Moving the display If you want to move the display from an eye temporarily, move the display up and down/left and right as shown in the next figure.
If you would like to move the display left and right, it’s better not to move B but move A since it’s more easier to put it back to the original position.
Status of Key operation the keyboard Bluetooth/Pow er indicator light Status/handling OFF Hold down [Power] key (3 sec or more) Lights red Low battery or internal error. Turn off the power and change 2 batteries. If this problem continues, please contact your local sales representative OFF Hold down [Power] key (3 sec or more) Lights green (3 sec) Lights orange (3 sec) Lights red (3 sec) Enough battery Battery is getting low ON Press [Power] ON Press [Power] key or while using the keyboard.
microSD card ■Supported microSD cards type of microSD card capacity microSD card Up to 2GB microSDHC card Up to 32GB microSDHC UHS-I card Up to 32GB ■Inserting/removing microSD card 1 Use your fingertip to pull the indent of the microSD card slot cap to open. 2 Use your fingertip to pull the indent of the microSD card slot cap to open. Insert a microSD card into the microSD card slot until it clicks.
3 Close the microSD card slot cap. Connecting a microUSB cable This is used when connecting the keyboard or a smartphone directly to the product. 1 Use your fingertip to pull the indent of the microUSB connector cap to open in the direction shown below. 2 Connect attached microUSB cable(TypeA connector) to the microUSB connector. There are TypeA and TypeB. Please check the engraved letter.
Be careful not to connect the microUSB in a wrong direction. It may damage the connector. 3 Connect the other side of the microUSB cable to the keyboard. Use your fingertip to pull the indent of the microUSB connector cap to open, insert the microUSB cable in the correct direction. If connecting the product and the smartphone using the microUSB cable, - Turn on the product and the smartphone’s power and connect TypeB microUSB cable to the product.
FCC and IC Regulatory Information Please note the following regulatory information related to the wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
government regulations arising from failure to comply with these guidelines. This device must not be co-located or operated in conjunction with any other antenna or transmitter. For IEEE 802.11a Wireless LAN: For operation within 5.15~5.25 GHz frequency range, it is restricted to indoor environments, and the antenna of this device must be integral.
FCC Radio Frequency Exposure statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
FCC et d’IC concernant l’exposition aux radiofréquences et s’est révélé conforme à ces dernières lorsqu’il a été testé en contact direct avec le corps. Export restrictions This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 class A of FCC Rules., as well as ICES 003 B A / NMB 003 B A.
Avis pour le Canada Le matériel destiné à un usage sur la bande 5 150 - 5 250 MHz doit être utilisé uniquement à l’intérieur afin de réduire les risques de brouillage nuisible causé aux systèmes mobiles par satellite fonctionnant sur un même canal. Un gain d’antenne de 6 dBi est autorisé (pour le matériel utilisant les bandes 5 250 - 5 350 MHz, 5 470 - 5 725 MHz et 5 725 - 5 825 MHz), conformément à la limite p.i.r.e. maximale permise selon l’annexe A9.2 afférent aux périphériques RSS210.
5. Appendix The motion space of a display The display can be moved in the following range. The motion space of a camera ■Camera arm There are three levels of height. You may adjust to 0 degree, about 20 degrees or about 40 degrees.
■Camera tip Specification ■Head Mounted Display Product name Head Mounted Display OS Android4.4.4 CPU 1.2GHz Quad Core CPU(APQ8026) Memory(RAM/ROM) 2GB/8GB Display Size 0.4 inches Virtual screen size 11 inches(Virtual viewing distance is 609.6mm) Resolution 854 x 480(FWVGA) Number of colors 24 bit color(Approx. 16,770,000 colors) Visibility adjustment +1~-2D Luminance(min~max) 10~1200cd/㎡ Distance from an eye 30.
Interface microSD card slot ×1 slot Audio Headset connection terminal 3.5φ x1 microUSB connector ×1(TypeAB) Water proofing, dust proofing IPX5 / IPX7, IP5X Battery capacity Lithium ion 3,300mAh Battery pack Battery life (when using an application that is connected with Wi-Fi Miracast) Approx.
■Wearable Keyboard Product name Wearable Keyboard Connection modes Bluetooth®Wireless/USB Wired Communication Bluetooth function Bluetooth V3.0 Interface ×1(TypeB) microUSB connector Water proofing, dust proofing IPX5 / IPX7, IP5X Battery ×2 AAA alkaline battery Battery life (when using AAA alkaline batteries) Approx. 5 months * Dimensions (W×D×H) (Not containing protrusion) W×D×H = 135mm × 68mm × 20mm Weight (Values are approx.