Monitor English Operating Manual SCENICVIEW A20W-3/A22W-3
Are there… ... any technical problems or other questions which you would like to be clarified? Please contact our help desk (see Warranty Booklet). The latest information on our products, tips, updates, etc., can be found on the internet under: http://www.fujitsu-siemens.
Published by Fujitsu Siemens Computers GmbH Order No.
SCENICVIEW A20W-3/A22W-3 LCD monitor Operating Manual Juni 2007 edition
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards Association. Copyright © Fujitsu Siemens Computers GmbH 2007 All rights, including rights of translation, reproduction by printing, copying or similar methods, in part or in whole, are reserved. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability. Right of technical modification reserved.
Contents Introduction........................................................................................................................................... 1 Notational conventions ................................................................................................................. 2 Important notes..................................................................................................................................... 2 Safety notes...............................................
Contents A26361-K1177-Z120-1-7619, edition 1
Introduction Your new LCD (Liquid Crystal Display) monitor SCENICVIEW A20W-3/A22W-3 offers numerous features and functions, for example: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● TFT display (Thin Film Transistor; active matrix) minimal space requirements thanks to slim casing optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour purity right into the corners) high degree of brightness and good contrast high resolution 1680 x 1050 (A20W-3/A22W-3) presentation of up to 16
SCENICVIEW A20W-3/A22W-3 Notational conventions The meanings of the symbols and fonts used in this manual are as follows: ! Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data. i Supplementary information, remarks, and tips follow this symbol. ► Text which follows this symbol describes activities that must be performed in the order shown. "Quotation marks" indicate names of chapters or terms.
SCENICVIEW A20W-3/A22W-3 ● No data transfer cables should be connected or disconnected during a thunderstorm. ● Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the device (danger of electric shock, short circuit). ● The device is not waterproof! Never immerse the device in water and protect it from spray water (rain, sea water). ● In emergencies (e.g.
SCENICVIEW A20W-3/A22W-3 Power cable To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements. ● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the outer sheath. ● For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.
SCENICVIEW A20W-3/A22W-3 FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation. NOTE: This equipment has been tested and found to comply with the limits for a "Class B" digital device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian InterferenceCausing Equipment Standard ICES-003 for digital apparatus.
SCENICVIEW A20W-3/A22W-3 Energy Star Guidelines The Fujitsu Siemens LCD monitor SCENICVIEW A20W-3/A22W-3 is designed to conserve electricity by dropping to less than 1 W when it goes into standby, suspend and OFF mode. With this new power management the LCD monitor SCENICVIEW A20W-3/A22W-3 qualifies for the U.S. Environmental Protection Agency's (EPA) Energy Star Computers award. The EPA estimates that computer equipment uses 5 % percent of all business electricity and that this is growing rapidly.
SCENICVIEW A20W-3/A22W-3 Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ! ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation. ► Check whether the delivery agrees with the details in the delivery note.
SCENICVIEW A20W-3/A22W-3 Installing an ergonomic video workstation 2 1 1 1= Windows Avoid direct and reflected glare. Avoid glare from electric lighting. 1= 2= Edge of desk Permissible reaching sector Position the keyboard where it is easiest to reach. 1 0° 65° 30° 60° 30° 65° 2 1= 2= Bearing surface for palms Example layout of monitor, keyboard and copy-holder of hands Reaching area for frequently used equipment Position the monitor for optimum viewing.
SCENICVIEW A20W-3/A22W-3 Mounting and removing the monitor base Mounting monitor base ! The display surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the monitor base.
SCENICVIEW A20W-3/A22W-3 Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base: ! The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the power socket. ► Lay the monitor on its face on a soft surface. ► Remove the screws on the rear of the monitor. You can now mount a swivel arm or a wall bracket as per VESA FPMPMI with 100 mm hole spacing.
SCENICVIEW A20W-3/A22W-3 Connecting the monitor ! Please take note of the safety information in the "Important notes" chapter. CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied. Do not cover the ventilation openings of the monitor. The computer power plug must be pulled out! ► Be sure that the monitor and the computer are switched off.
SCENICVIEW A20W-3/A22W-3 ► Mount the cover over the connections. i A lock (Kensington Lock) can be mounted in the security slot (4) to protect the monitor from theft. A Kensington Lock is not included in the consignment of the monitor. Connecting cables to the computer Information on the computer connections and interfaces is contained in the operating manual for your computer.
SCENICVIEW A20W-3/A22W-3 Operation of the monitor The monitor offers the following possibilities that enable it to be optimally adjusted for the respective user and the respective situation. Adjusting rake The rake of the monitor can be adjusted by –5° (forward) and +20° (back) from its vertical position. ► Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the desired rake.
SCENICVIEW A20W-3/A22W-3 The power indicator (2) lights up blue when the monitor and computer are switched on. The power indicator lights up orange when the monitor does not receive a video signal or is in the energy saving mode. The power indicator goes off when the monitor is switched off. When you switch the computer system on, you must proceed in the following order: ► First switch on the LCD monitor with the ON/OFF switch (2). ► Then switch on the computer.
SCENICVIEW A20W-3/A22W-3 Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs. Choosing basic monitor settings using the supplied software If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000, Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be set with the CD supplied.
SCENICVIEW A20W-3/A22W-3 Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor with the ON/OFF switch. A message is displayed that the action has been performed. Please proceed in the same manner to release the locked OSD menu again.
SCENICVIEW A20W-3/A22W-3 The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side). The first function (H-Position) is highlighted. ► If necessary, press the 6 or 5 button to mark another function. ► Press the SELECT/MENU button to select the highlighted function. ► Press the 6 or 5 button to adjust the value for the selected function. ► Press the EXIT/AUTO button to exit the function.
SCENICVIEW A20W-3/A22W-3 Adjusting size and position Calling the Image adjust setting window H-Position Adjusting the horizontal position With this function you move the picture to the left or to the right. V-Position Adjusting the vertical position With this function you move the picture up or down. Clock Setting synchronisation With this function you adjust the picture width to eliminate vertical picture disturbances.
SCENICVIEW A20W-3/A22W-3 Setting display of the OSD menu Calling the OSD Setup setting window Language Setting language for the OSD menu With this function you choose between English (default setting), French, German, Italian, Spanish, Russian, Dutch and Swedish as the language for the OSD menu. OSD H-Position Setting the horizontal position of the OSD menu With this function you move the OSD menu to the left or to the right.
SCENICVIEW A20W-3/A22W-3 Notes on ergonomic colour adjustment If you select colours for the display in your application programmes, take note of the information below. The primary colours blue and red on a dark background do not produce the minimum required contrast of 3:1 and are therefore not suitable for continuous text and data entry.
SCENICVIEW A20W-3/A22W-3 Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you are unable to solve the problem, please inform our help desk. Having this problem? No screen display (power indicator does not light) Check the following points: ► Check whether the power cable on the monitor is connected correctly. ► Check whether the computer is switched on.
SCENICVIEW A20W-3/A22W-3 Having this problem? Picture is wrongly adjusted Picture disturbances (vertical lines) Check the following points: ► Press the SELECT/MENU button to activate the function Factory Recall. The Auto Processing message is displayed. ► Press the EXIT/AUTO button to perform the autoadjustment of the screen. Picture disturbances (horizontal lines, picture noise) ► The screen becomes darker The background lighting has a limited lifetime.
SCENICVIEW A20W-3/A22W-3 Notes regarding the DIN EN ISO 13406-2 standard Permanently unlit or lit pixels The standard of production techniques today cannot guarantee an absolutely fault-free screen display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum permitted number of pixels faults is stipulated in the stringent international standard ISO 13406-2 (Class II). Examples: A flat-screen monitor with a resolution of 1680 x 1050 has 1680 x 1050 = 1764000 pixels.
SCENICVIEW A20W-3/A22W-3 Technical data A20W-3 A22W-3 Dimensions and weight Visible diagonals: Dot pitch: Screen size: Width: Height: Maximal resolution: Dimensions incl. monitor base: Box dimensions: Width: Height: Depth: Width: Height: Depth: 51 cm 56 cm 0,28 mm 0,28 mm 435.01 mm 272.47 mm 475.36 mm 297.70 mm 1680 x 1050 1680 x 1050 472.89 mm 400.40 mm 221.00 mm 525 mm 460 mm 145 mm 513.76 mm 416.02 mm 221.00 mm 560 mm 480 mm 140 mm Weight (without packaging): 4.6 kg 5.
SCENICVIEW A20W-3/A22W-3 Environmental conditions Environment class 3K2, IEC 721 Rated range of operation: Humidity: 15 °C .... 35 °C 20 % .... 85 % Limit range of operation: Humidity: 5 °C .... 35 °C 20 % .... 85 % Condensation must be avoided. VESA-DDC-compatible VGA interface Your monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (Video Electronics Standard Association, Display Data Channel) is used as the communications interface between the monitor and the computer.
SCENICVIEW A20W-3/A22W-3 Pin assignment D-SUB 5 1 6 10 15 11 Pin Meaning Pin Meaning 1 Video input red 9 +5 V (DDC) 2 Video input green 10 Sync. earth 3 Video input blue 11 Earth 4 Earth 12 DDC-Data 5 Earth 13 H. sync 6 Red video earth 14 V.