SYSTEM BOARD D1321 SYSTEM BOARD D1321 TECHNICAL MANUAL TECHNICAL MANUAL
Sie haben ... ... technische Fragen oder Probleme? Wenden Sie sich bitte an: • Ihren zuständigen Vertriebspartner • Ihre Verkaufsstelle Weitere Informationen finden Sie im Handbuch "Sicherheit, Garantie und Ergonomie". Aktuelle Informationen zu unseren Produkten, Tipps, Updates usw. finden Sie im Internet: http://www.fujitsu-siemens.com Are there ... ...
Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.
Deutsch English Systembaugruppe D1321 System Board D1321 Technisches Handbuch Technical Manual Ausgabe August 2001 August 2001 edition
Intel, Pentium und Celeron sind eingetragene der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt.
Contents Introduction........................................................................................................................................1 Notational conventions ..............................................................................................................1 Important notes .................................................................................................................................1 Information about boards...............................................
Introduction i Depending on the configuration chosen, some of the hardware components described may not be available on your system board. You will find further information in the "BIOS Setup" description. Further information about drivers is provided in the readme files on the hard disk, on the supplied drivers diskettes, on the "Drivers & Utilities" or on the "ServerStart" CD.
Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device. Connecting cables for peripherals must be adequately shielded to avoid interference. ! i Components can become very hot during operation.
Features Features The components and connectors marked are not necessarily present on the system board. • • System board in µATX format mPGA478 Intel processor Pentium 4 with 400 MHz Front Side. Pentium 4 processors support MMX technology and Intel Streaming SIMD Extensions. The size and frequency of first-level cache and second-level cache are dependent upon the processor used.
Features • • • • • • • • • • • 1 AGP slot The AGP slot supports 1x, 2x and 4x AGP mode. Only AGP boards with 1.5 V are supported. IDE hard disk controller connected to PCI bus for up to four IDE drives (e.g. IDE hard disk drives, ATAPI CD-ROM drives) The IDE hard disk controller are ATA33/66/100, ultra DMA capable and support PIO modes 04. Floppy disk drive controller (possible formats: 720 KB, 1.44 MB, 2.88 MB) The system board supports booting from a 120 MB IDE floppy disk drive.
Features Internal ports and connectors 1 2 3 4 5 6 7 8 DIMM 3 DIMM 2 DIMM 1 9 10 13 1= 2= 3= 4= 5= 6= 7= 8= Power supply ATX Floppy Disk Drive IDE drives 3 and 4 (secondary) Connector for control panel and loudspeaker IDE drives 1 and 2 (primary) Voltage indicator LED Fan 2 Cover monitoring 12 PCI 3 PCI 2 PCI 1 AGP 14 11 9 = USB ports C / D * 10 = Wake On LAN 11 = CD audio input 12 = AUX audio input 13 = Power supply +12 V 14 = Fan 1 (e.g.
Features Hard disk connection An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for the ultra ATA/66or ultra ATA/100 mode. Ê Connect the end of the cable marked with blue to the system board. LAN connector This system board has an optional Intel 82550ET LAN controller which supports transfer speeds of 10 Mbit/s and 100 Mbit/s. The LAN controller is equipped with a 3 KB transmission and receiving buffer (FIFO) and supports WOL function through Magic Packetä.
Settings with switches and jumpers Settings with switches and jumpers ON 1 2 3 4 i Switch 1 = must always be set to off Switch 2 = System BIOS recovery Switch 3 = must always be set to off Switch 4 = must always be set to off The clock frequency of the processor is set automatically. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed.
Add-on modules Add-on modules ! Exit Suspend mode, switch off the device and remove the power plug from the mains supply, before carrying out any of the procedures described in this chapter! Even when you have switched off the device, parts (e.g. memory modules, AGP and PCI extension boards) are still supplied with power. The voltage indicator LED will glow if this is the case. All PCI slots support 3.3 V main and auxiliary voltages. AGP boards support 1,5 V main and auxiliary voltages.
Add-on modules Installing and removing processors 3 2 4 5 1 A Ê Ê Ê Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Remove the old processor from the socket (3). Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). ! Ê The angled corner of the processor may be covered by the heat sink.
Add-on modules Upgrading main memory These slots are suitable for DIMM format 32, 64, 128, 256, 512, 1024 MB SDRAM memory modules. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 3.3 V memory modules. Buffered memory modules are not supported. SDRAM memory modules must meet the PC133 specification. Installing a memory module 2 2 Ê Ê Ê Push the holders on each side of the memory compartment outwards. Insert the memory module into the location (1).
Add-on modules Installing network board with WOL Ê Ê Install the network board as described in the operating manual for your unit. Push the WOL cable onto the WOL plug connector of the system board. i To use the WOL functionality of a network board the power supply must provide a 5 V auxiliary voltage of at least 1 A. If the system board was not already incorporated in a device when you bought it you must check whether your power supply can provide the auxiliary voltage.
Add-on modules Replacing the lithium battery ! Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer (CR2032). Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste. Ensure that you insert the battery the right way round.
Glossary Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described system board.
