DESKPOWER 6000/SS Series User’s Manual Fujitsu endeavours to ensure that the information in this document is correct, but accepts no liability for any error or omission in the same. Any procedures described in this document for operating Fujitsu products should be read and understood by the operator before such products are used. To ensure that Fujitsu products function without risk to safety and health, such procedures should be strictly observed by the operator.
Greetings ○ ○ ○ ○ ○ ○ ○ ○ We thank you for purchasing the Fujitsu DESKPOWER 6000/SS personal computer. The DESKPOWER 6000/SS is a desktop-type personal computer with a space-saving design. This manual explains how to use the hardware of the DESKPOWER 6000/SS. Please read this manual carefully to ensure correct use of the PC. June 1999 This unit may malfunction if the power source is interrupted suddenly, for example, due to lightning. Fujitsu recommends the use of an AC non-interruptible power supply unit.
Conventions used in this manual ○ ○ ○ ○ ○ ○ ○ ○ ● Warning icons Various icons and icon/word combinations are used in this manual to encourage users to use the equipment so as to minimize personal risk and prevent property damage. The icons are explained as follows. The user should be familiar with the icons before responding to the corresponding instructions. WARNING CAUTION Indicates a hazardous situation that could result in fatal or serious wound if the correct procedure is not applied.
A blank (shown with [↑]) between characters indicates that the [Space] key (long bar on the front of the keyboard) is to be pressed once. Command names are represented in lowercase but may be entered using uppercase letters. ● Conventions used in the text of the manual The symbols used in the text of the manual have meanings as explained below: Point Point indicates information necessary to run hardware or software.
Warning and caution labels ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ The PC bears warning and caution labels as shown below. The warning and caution labels must not be removed or damaged. WARNING Before disassembling the unit and installing a built-in option, switch off the PC and all connected peripherals and unplug all power cords from respective outlets to prevent electric shock.
Man Manual configuration Chapter 1 Installation and Connection This chapter outlines precautions that should be noted when installing the PC and explains how to connect various cables. Consult this chapter before assembling the PC. Chapter 2 Basic Operations This chapter explains basic operations required to use the PC, such as how to switch the power on and off and how to proceed with storage media. Consult this chapter.
Greetings ..................................................................................................... ii Conventions used in this manual ................................................................. iii Warning and caution labels ......................................................................... v Manual configuration .................................................................................. vi Chapter 1 Installation and Connection 1 Installation .............................
5 CD-ROM ...................................................................................... 16 Handling precautions ................................................................................. 16 Mounting and dismounting a CD-ROM disk .............................................. 17 6 Hard Disk ..................................................................................... 18 What is a hard disk? ...................................................................................
4 Security Menu ............................................................................. 47 Details on setup items ................................................................................ 47 Setting a password .................................................................................... 50 Changing passwords ................................................................................. 53 Deleting passwords .............................................................................
2 Standard Specifications ............................................................ 81 PC main unit specifications ........................................................................ 81 LAN adapter specifications ........................................................................ 82 Sound specifications ................................................................................. 82 Resources .................................................................................................
1 Chapter 1 Installation and Connection This chapter outlines precautions that should be noted when installing the PC and explains how to connect various cables. 1 2 Installation .............................................................................................2 Connection ............................................................................................
Installation This section provides notes on installing and using the PC. Installation location ○ ○ ○ ○ ○ ○ Do not install the PC in the following areas: - Areas exposed to moisture, dust, or smoke. - Areas poorly ventilated. - Areas having open flames. - Areas that may expose the PC to water. - Areas exposed to direct sunlight or high temperatures. - Areas having temperatures below 10°C. - Areas that are unusually small or crowded. - Areas having a strong magnetic field (close to a TV or speaker).
● Horizontal installation PC main unit Only a 17 inches or smaller-size Display display can be installed on the top of the PC main unit. Do not install a 19-kg or greater-weight display on the top of the PC unit. Ventilation holes 1 Keyboard Mouse Point This instruction will proceed for the PC main unit to be positioned vertically. When posititioning it horizontally, replace the description “vertically” as “horizontally”.
Connection Connect the display, keyboard, and power cord to your PC main unit. WARNING ● To prevent electric shock, ground the device (if required) before providing power to the equipment. To prevent fire, do not connect the ground wire to a gas pipe. Connect the LAN cable. Attach one end of the twisted pair cable to the network connector, such as a hub.
Attaching display, keyboard, mouse, and LAN cables ○ ○ ○ ○ ○ ○ ○ ○ Point This section explains how to connect a liquid-crystal display. To connect a CRT display, use the power cord included with your PC package. The power cord included with the CRT display is not used. Connect the LAN cable Attach the other end of the twisted pair cable (purchased separately) to the LAN connector on the rear of the PC main unit. 1 Connect the power cord to the outlet.
Connecting the power cord ○ ○ ○ ○ ○ ○ After connecting the display and other peripherals to the PC main unit, note the following when connecting the power cord of the PC main unit. - Do not plug or unplug the power cord with wet hands. - Do not damage or remodel the power cord. - Do not bend, stretch, or place heavy objects on the power cord. - Do not use the PC if the power cord or plug is damaged. - If the electrodes of the power cord plug or the corresponding outlet is dusty, wipe with a dry cloth.
- Unplug all power cords during an electrical storm. - If only a two-pin outlet is available, use the adapter plug provided and connect the ground wire. - When unplugging a power cord, secure the plug housing. - Ensure that the power plug is fully inserted into the outlet. - Unplug the PC when not being used for a period of time. 1 Attach the power plug to the inlet on the rear of the PC. Connect the power plug to a power source. Insert the other end of the power plug into the outlet.
Upon completion of all connections ○ ○ ○ ○ ○ ○ Upon completion of all connections, fill out all user registration cards included with your PC package and mail. The registration cards are used by manufacturers to obtain user information.
2 Chapter 2 Basic Operations This chapter explains basic operation methods of the PC such as how to turn the power on and off and handle storage media. 1 2 3 4 5 6 Switching on ........................................................................................10 Switching off ........................................................................................11 Reset ...................................................................................................13 Floppy Disk ..................
Switching on This section explains how to switch on the PC. CAUTION ● To prevent malfunction after turning on the PC, do not move equipment or subject equipment to shock and/or vibration. 1 Press the power switch of the display. There is no display. 2 Press the power switch of the PC main unit. Power switch The green power lamps of the PC main unit and display go on. When the power is turned on, “Fujitsu” appears on the screen and the system starts shortly thereafter.
Switching off This section explains how to turn off the PC. Point - Before turning off the power, terminate all jobs and save all necessary data. - Before turning off the power, confirm that the access indicator lamps ( see Appendix 1, “Name and Function of Each Component”) of the floppy and hard disk drives are off. If the power is turned off while the access indicator lamps are on, data may be lost or data in the floppy disk or hard disk may be destroyed.
Turning off the power via Windows NT ○ ○ ○ ○ ○ ○ ○ 1 Click [Start]. The “Start” menu appears. 2 Click [Shut Down]. The following dialog box appears. 3 Check that “Shut down the computer?” has been selected and then click [Yes]. Turn off the power switch. Help If the message “you can safely switch off power” appears and the power is not turned off automatically, press the power switch. Point The following procedure can also be used to turn off the power: 1 Press [Ctrl] + [Alt] + [Delete].
Resets The PC is reset after software is installed or if software fails to run normally. This section explains how to reset the PC. Point Resetting the PC results in memory data being lost. Before resetting, save all necessary data. Resetting the PC via Windows 95/98 ○ ○ ○ ○ ○ ○ ○ 2 This section explains how to reset the PC via Windows 95/98. 1 Click [Start] and “Shut Down.” The “Shut Down Windows” dialog box appears. 2 Select “Restart the computer?” and then click [OK]. The PC is reset.
Floppy Disk A floppy disk is a storage medium used to save programs and other information. This section explains how to mount and dismount floppy disks. Handling precautions ○ ○ ○ ○ ○ ○ ○ To prevent malfunctions, note the following precautions regarding floppy disks: - Do not get wet. - Do not open the disk shutter. - Do not bend or place heavy objects thereon. - Do not expose to magnetic force. - Do not drop. - Do not store in areas exposed to high or low temperatures.
● Dismounting a floppy disk 1 Confirm that the floppy disk access indicator lamp is off. Floppy disk access indicator lamp Point To prevent data from being destroyed, do not dismount a floppy disk from the drive when the floppy disk access indicator lamp is on. 2 2 Press the floppy disk eject button. The floppy disk is ejected.
CD-ROM Your PC incorporates a CD-ROM drive (if a CD-ROM drive-equipped model). This section explains how to handle, mount, and dismount CD-ROM disks. Handling precautions ○ ○ ○ ○ ○ ○ ○ ○ To prevent malfunctions, note the following precautions regarding CD-ROM disks: - Do not write on the label side (printed side) using a ball-point pen or pencil and do not affix extra labels. - Do not touch or scratch the data side. - Do not bend or place heavy objects thereon.
Mounting and dismounting a CD-ROM disk ○ ○ ○ ○ ○ ○ ○ ○ ● Mounting a CD-ROM BUSY lamp 1 Press the EJECT button. EJECT button Pressing the EJECT button ejects the CD-ROM tray from the drive. 2 Pull out the tray. Tray Pull out the tray as shown on the right. 2 3 Label side With the label of the CD-ROM disk facing up, place the CD-ROM disk in the center of the projection tray until it clicks. Tray Projection Hold the tray so that the unit may not be overturned.
Hard Disk Your PC incorporates a built-in hard disk. This section outlines precautions to take when handling a hard disk. What is a hard disk? ○ ○ ○ ○ ○ ○ ○ ○ A hard disk is used to save software and other data and consists of a magnetic disk packed in a box as shown on the right. A hard disk can save more data and can read and write data faster than is possible with floppy disks.
3 Chapter 3 Installing Internal Options This chapter explains how to install internal options in your PC. 1 2 3 Introduction ..........................................................................................20 Installing Memory Modules ..................................................................23 Installing Expansion Cards ..................................................................
Introduction The features and performance of your PC can be upgraded by installing options. This section explains the types of internal options that can be installed in the PC and how to remove the upper cover in preparation for installing the internal options. Handling precautions ○ ○ ○ ○ ○ ○ Note the following when installing internal options: - Before starting operation, switch off the PC and all connected peripherals and unplug power cords from respective outlets.
Installing positions of internal options ○ ○ ○ ○ ○ ○ Extension card slot Expansion cards extend the range of the features of the PC. For example, installing a SCSI card enables the use of a SCSI-standard hard disk and a magneto-optical disk drive. 3 Memory slot Memory expansion increases the amount of data to be read and enhances the throughput of the PC.
Removing the upper cover ○ ○ ○ ○ ○ ○ When installing internal options, remove the upper cover so as to reveal the inside of the main unit. 1 Remove two screws at the rear of the PC main unit. 2 Remove the upper cover. Slide the upper cover to the front of the PC main unit, then lift and remove the cover. Point To replace the cover, reverse the above procedure.
Installing Memory Modules This section explains how to install and remove additional memory modules. Memory expansion in your PC increases the amount of data to be read and enhances the throughput of the PC. DIMM1 DIMM2 3 Point To install a memory module, set up the PC, turn off the power, and install the memory module. WARNING ● To prevent electric shock, before installing and removing memory modules, turn off the PC and connected units and unplug power cords from respective outlets.
Memory combination table ○ ○ ○ ○ ○ ○ ○ Install a memory module to DIMM1 and DIMM2. A memory module has been installed in DIMM1 as standard. Check the combination of memory capacity and slot using the following table to install the memory module. Using a combination other than below may result in faulty operation of the PC. Point Use a genuine Fujitsu part called “168-pin SDRAM DIMM (100 MHZ) memory” for this PC. The PC may not work correctly if the recommended Fujitsu memory module is not used.
3 Insert the memory card into the slot. - Insert the memory card into the slot such that the notches of the memory card face the rear of the PC main unit. The hooks at both ends of the slot are raised. Confirm that the memory card is securely locked in place. Notch or - Insert the memory card into the slot such that the notches of the memory card face the front of the PC main unit. The hooks at both ends of the slot are raised. Confirm that the memory card is securely locked in place.
Installing Expansion Cards This section explains how to install expansion cards, which extend the range of the features of your PC. PCI1 PCI2 Point - To install an expansion card, set up the PC, turn off the power, and install the expansion card. - An expansion card up to 176-mm (half size) in size can be installed in the upper PCI slot, and an expansion card up to 150-mm in size can be installed in the lower PCI slot.
To operate expansion cards, “resources” required for operation must be reserved. The floppy disk drive or hard disk drive inside the PC uses predetermined paths specific to those devices when transferring data with the CPU and memory. These paths include I/O port addresses, DMA channels, and interrupt levels (IRQ), which are generally called “resources.” Expansion cards for PCI bus can be installed in the PC.
6 Install the retaining metal bracket at the side. Insert the pawls of the retaining metal bracket into the groove on the front of the PC main unit, then install the metal bracket. Secure the metal bracket with the screw removed in step 2. 7 Attach the upper cover. Point - Store the removed slot cover. - To remove the expansion card, reverse the above steps.
4 Chapter 4 BIOS Setup This chapter describes how to perform BIOS setup when installing an optional product or setting power savings mode. 1 2 3 4 5 6 7 8 Preface ................................................................................................30 Main Menu ...........................................................................................33 Detail Menu ..........................................................................................37 Security Menu ..........................
Preface What is BIOS setup? ○ ○ ○ ○ ○ ○ ○ BIOS setup is a program that helps the user set up a hardware environment, including memory, hard disks, and floppy disk drives. Minimum setup has already been installed on this personal computer when you purchase it. BIOS must be set up under the following circumstances: - When a storage unit, such as a floppy disk drive or a built-in hard disk (IDE), is mounted or removed. - When a password permitting specific users to access the PC is set.
4 A message “Press , , or selects field.
Menus ○ ○ ○ ○ ○ ○ The BIOS setup utility screen includes the following menus, under which setup items are listed. For details on menus and setup items, see the following sections. ● Main menu Used to set up the date and time and drives. ● Advanced menu Used to set up port addresses. ● Security menu Used to set up the computer so as to be accessible to specific users. ● Power menu Used to set up power savings mode. ● Boot menu Used to set up the priority of boot drives.
Main Menu The Main Menu is used to setup the date and time and drives. Select the ← or → key to select [Main] and display the Main menu. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Info Exit Item Specific Help System Time: System Date: [12:34:56] [20/06/1999] Legacy Diskette A: [1.44/1.25 MB 3.5”] :Primary Master: :Primary Slave: :Secondary Master: :Secondary Slave: Language: F1 Help ESCExit [6449 MB] [None] [CD-ROM] [None] Adjust calendar clock.
● Primary Master/Save, Secondary Master/Slave Menu Using submenus, set the type of hard disk (master or slave) mounted on the primary IDE connector (Adapter 0) and secondary IDE connector (Adapter 1) as well as the size and the number of cylinders). Move the cursor to a desired item and press the Enter key to display the selected submenu.
– Multi-Sector Transfers This item displays the contents detected by the PC when ‘Type’ is [Auto]. If ‘Type’ is a value other than [Auto] and [None], set the number of sectors that can be transferred in a single operation. A larger number of sectors specified will allow greater disk access. - Disabled The computer transfers data sector by sector. Select this item when the connected disk does not support multi-sector transfer.
– Ultra DMA Mode This item sets the data transfer mode between device hosts, such as multiword DMA, ultra DMA/33. The best mode is selected and displayed automatically when ‘Type’ is [Auto]. If ‘Type’ is other than [Auto] and [None], the user can select a desired transfer mode. - Disabled (Initial value) DMA transfer is disabled. - Multiword DMA 0/1/2, Ultra DMA 0/1/2 Select a desired multiword DMA or ultra DMA/33 transfer mode. A larger number indicates a higher transfer rate.
Detail Menu The Detail menu is used to set up devices. Select Detail with the ← or → key to display the Detail menu.
● Serial/Parallel Port Configurations This item sets the I/O address of the serial and parallel ports and has submenus. Move the cursor to this item and press the Enter key to display a submenu as shown below.
– Serial Port 2 This item sets the I/O port address and interrupt number of serial port 2. - Disabled Serial port 2 is disabled and resources are freed. - Enabled (Initial value) Set the I/O port address and interrupt number of serial port 2. - Auto The personal computer automatically assigns an I/O port address and an interrupt number. Point - When ‘Serial Port 1’ is [Disabled], the port is not transparent to devices controlled by the Windows 95/98 APM device manager.
Mode This item appears when ‘Parallel Port’ is [Enabled]. Set the operating mode of the parallel port. - Output only Select when connecting a peripheral unit using output mode only. - Bi-directional (Initial value) Select when connecting a peripheral unit using bi-directional mode. - EPP Select when connecting an EPP standard peripheral unit. - ECP Select when connecting an ECP standard peripheral unit. I/O Address This item appears when ‘Parallel Port’ is [Enabled].
– Numlock This item sets whether the keyboard tenkey pad is set to Numlock mode at boot or reboot. In Numlock mode, the user can enter numeric values from the tenkey pad. - Auto (Initial value) The keyboard tenkey pad is set to Numlock mode when the keyboard has a Numlock key. - On The keyboard is set to Numlock mode. - Off The keyboard is not set to Numlock mode. Point In some Oss, this has to be set on the OS side. – PS/2 Mouse This item enables the PS/2 mouse controller.
● Internal Devices Configurations This submenu is used to set up built-in devices. Move the cursor to this item and press the Enter key to display a submenu as shown below.
– LAN Controller This item sets whether the LAN adapter on the mother board is enabled. - Disabled The LAN adapter is disabled and resources are freed. - Enabled (Initial value) The LAN adapter is enabled. – USB Peripherals This item sets whether the devices connected to the USB connector are enabled. - Disabled The devices connected to the USB connector are disabled. - Enabled (Initial value) The devices connected to the USB connector are enabled.
● CPU Features This submenu is used to set up the CPU. Move the cursor to this item and press the Enter key to display a submenu as shown below. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Info CPU Features Processor Serial Number: [Disable] Exit Item Specific Help When your system has a Pentium III processor,select for using Procesor Serial Number. [Enable] Processor Serial Number is Enabled. [Disable] Processor Serial Number is disabled.
● Event Logging Configurations This submenu is used to set up event logs. Move the cursor to this item and press the Enter key to display a submenu as shown below.
System Boot Event This item appears when ‘Event Logging’ is [Enabled] and sets whether system boot events are logged. - Disabled (Initial value) System boot events are not logged. - Enabled System boot events are logged. ECC event This item appears when the DRAM ECC function is enabled and ‘Event Logging’ is [Enabled] and sets whether ECC events are logged. - Disabled ECC events are not logged. - Enabled (Initial value) ECC events are logged.
Security Menu The Security menu is used to set up the PC such that it is accessible to specific users only. Select Security with the ← or → key to display the Security menu.
● User Password This item displays the status of user passwords. - Clear No password is set. - Set A password is set. - Disabled The password jumper is set to Disabled and passwords are disabled. ● Set Supervisor Password Press the Enter key to set the entered supervisor password. Point - When ‘Set Supervisor Password’ is set, the supervisor can manage user access to the BIOS setup utility.
● Password on Boot This item appears when ‘Supervisor Password’ is set. Set whether the computer requests the user to enter a password when it is booted. - Disabled (Initial value) No password is requested at boot. - First Boot The user is requested to enter a password at the initial OS boot. - Every Boot The user is requested to enter a password at every OS boot. Point This item appears only when the computer is turned on with the Power switch.
● Floppy Disk Access This item appears when ‘Supervisor Password’ is set. Set the right to use floppy disk drives. - All (Initial value) All users can use floppy disk drives. - Supervisor Only the supervisor can use floppy disk drives when ‘Password on Boot’ is set. If ‘Password on Boot’ is not set or at automatic wakeup, all users cannot use floppy disk drives. Point This item may not operate properly on OSs not using BIOS to access floppy disk drives, such as Windows NT.
2 Enter a password not exceeding seven digits. The password can contain alphanumeric characters. The entered characters are not displayed and “ ” appears. The minimum length of user passwords can be set in ‘Set User Password Length.’ 3 After entering a password, press the Enter key. The cursor moves to the “Enter New Password” field and the utility requests that the password be entered again. 4 Enter the same password as in Step 2 again and press the Enter key. The Notice window appears.
WARNING ● To prevent electric shock, before changing jumper switches, turn off the computer main and peripheral units and unplug the power cable. CAUTION ● The PC is very hot immediately after being turned off. Wait about ten minutes and reboot. 1 2 3 JP5 jumper switch 1-2... Enables a password. 2-3... Disables a password. 1 3 Front Even if passwords are set by the BIOS setup utility, they are not rendered effective until the jumper switches are changed.
● Starting the computer after password setup After ‘Set User Password’ is set, the personal computer displays a password entry window when turned on again or the user attempts to run the BIOS setup utility. Enter a password and press the Enter key. Enter Password. After ‘Set Supervisor Password’ is set, the computer displays a password entry window when the user attempts to run the BIOS setup utility. Enter a password and press the Enter key. Enter Password.
Power Menu The Power menu is used to set up the power savings mode. The power savings mode is used to place the computer in standby mode and reduce power consumption if the system is on but not being used. Select Power using the ← or → key to display the Power menu.
- Maximum Performance Maximize This item reduces power consumption while degrading performance. ‘Hard Disk Timeout’ is set to [30 minutes]; ‘Display Timeout’ to [1 hour]; and ‘Standby Timeout’ to [1 hour], respectively. Point - If this item is set [Disabled] on Windows 95/98, the computer displays the message “Ready to Turn off power”, and its power is not automatically turned off. If this message is displayed, you have to turn off the power.
– Standby Timeout This item appears when ‘Power Savings’ is [Enabled]. Set the time from no key entry or data input/output to the time the PC enters standby mode. - Disabled The computer does not enter standby mode - 1 to 30 minutes, 1 hour (Initial value: 30 minutes) Point This item is not available for Windows 98. ● Power Switch Mode This item appears when ‘Power Savings’ is [Enabled]. Set whether to enter power savings mode or to turn off the power when the Power switch is pressed.
– Wake up LAN This item sets whether to turn on the computer or to return from Suspend mode when a magic packet is received from the standard LAN port. - Disabled (Initial value) The computer is not turned on or returned from Suspend mode after receiving a magic packet. - Enabled The computer is turned on or returned from Suspend mode after receiving a magic packet. Point - This item is not available when Windows 98 runs in ACPI mode. - For PME LAN cards (PCIs), use ‘Wake up on PCI PME.
– Wake up on Time This item sets whether to turn on the computer or to return from suspend mode at the time specified in ‘Wake up Date’ and ‘Wake up Time.’ - Disabled (Initial value) The computer is not turned on or returned from Suspend mode at a specified time. - Enabled The computer is turned on or returned from Suspend mode at a specified time. Wake up Date This item appears when ‘Wake up on Time’ is set. Set the computer wake-up date.
– Sleep mode This item sets sleep mode for OSs supporting ACPI. - S1 (Initial value) Sets S1 sleep mode (CPU stop). - S3 Sets S3 sleep mode (power off other than RAM). - Disabled ACPI is disabled. Point If an error occurs in an extension card or peripheral unit when [S3] is selected, set to [S1].
Boot Menu The Boot menu is used to set the priority of boot drives. Select Boot using the ← or → key to display the Boot menu. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Info Exit Item Specific Help QuickBoot: Boot-time Diagnostic Screen: Preboot Execution Environment: Delay Time for ATA/ATAPI Drive: :Boot Device Priority [Enabled] [Disabled] [Disabled] [3 seconds] [Enabled] Some diagnostic tests may be skipped while booting to speed up. [Disabled] All diagnostic tests will be done.
● Boot Time Diagnostic Screen This item sets whether to display the self diagnostic (POST) screen at boot or reboot. - Disabled (Initial value) The FUJITSU logo is displayed at boot or reboot. - Enabled The self diagnostic (POST) screen is displayed at boot or reboot. Point To confirm BIOS messages from an extension card, select [Enabled]. ● Preboot Execution Environment This item sets whether to preboot from the network server.
● Boot Device Priority This item sets the priority of devices to load the OS using a submenu. Move the cursor to this item and press the Enter key to display a submenu as shown below. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Info Boot Device Priority 1. 2. 3.
Info Menu The Info menu is used to provide the hardware configuration of the personal computer The setting of this menu cannot be changed. Select this item with the ← or → key to display the Info menu. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Info Exit Item Specific Help BIOS Version: BIOS Date: BIOS Area: 1.
● L2 Cache Displays the size of the CPU secondary cache memory. ● Total Memory Displays the total memory size (RAM) mounted on the computer. – Memory Slot 1/2 Detects and displays the type of memory mounted on each memory slot. A slot with no memory mounted is indicated as “Not used.” ● ECC This item sets whether to perform memory error check (ECC mode). - Disabled Memory check is disabled.
Exit The Exit menu is used to exit the BIOS setup utility and to reset to standard setup values. Select Exit with the ← or → key to display the Exit menu. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Info Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help ESCExit ↑↓ Select Item ←→ Select Menu Exit System Setup and save your changes to CMOS.
● Exit Discarding Changes This item exits the BIOS setup utility without saving changes to the CMOS RAM and reboots the computer. All changes are discarded. If the Enter key is pressed while changing setup values, the message shown below is displayed. To discard changes, select [No] and press the Enter key. Setup Confirmation Configuration has not been saved! Save before exiting? [Yes] [No] ● Load Setup Defaults This item loads default values to all setup items.
5 Chapter 5 Troubleshooting This chapter explains the procedure to follow if the computer does not operate as expected. 1 2 Error Messages ...................................................................................68 Troubleshooting ...................................................................................
Error Messages This section provides a list of error messages and suitable responses thereto. Consult this section as required. Error messages displayed by the PC ○ ○ ○ ○ ○ ○ Error Message Description and necessary action An error occurred at address If an extended RAM module is used, remove the xxxx during a system memory module and determine whether the error recurs. If this test. message is not displayed, an extended RAM module error is expected.
Error Message Description and necessary action An invalid hard disk drive was set. Confirm ‘Primary master’ or ‘Secondary master’ on the BIOS setup main menu. If the message is still displayed, contact a dealer or the your local distributor. Turn the power off, then on again. If the message is still displayed, contact a dealer or the your local distributor. Confirm BIOS setup items, then If the message is still displayed, contact a dealer or the save. your local distributor.
Error Message Description and necessary action Invalid system disk Replace the disk, and the disk, and then press any key This message is displayed if the computer is turned on with a floppy disk other than a system disk set on the floppy disk drive. Remove the floppy disk and press any key. Non-System disk or disk error Replace and press any key when ready. This message is displayed if the computer is turned on with a floppy disk other than a system disk set on the floppy disk drive.
Correcting errors ○ ○ ○ ○ ○ ○ If an error message is displayed, respond as follows. - Running the BIOS setup utility If a BIOS setup error message is displayed, retry the BIOS setup utility. - Confirming that built-in options are mounted correctly If optional extension cards are mounted, confirm that the cards are mounted and set up correctly. Also conform that the card is properly set. If available, consult manuals or utility software with extension cards.
Troubleshooting This section provides troubleshooting information for each function. Consult this section as required. For troubleshooting information for Windows NT, refer to the Windows NT manual or the online help registered on the Start menu. Troubleshooting information on the computer main unit and peripheral units ○ ○ ○ ○ ○ ○ ● The access lamp does not light up. The PC may be faulty. Contact a dealer or the your local distributor. - No data is displayed on the screen.
● The power is not turned on or the Power lamp on the front panel does not light up. Is the power cable plugged in? ● Data cannot be read from the CD-ROM drive. Check the following: - Is the CD-ROM centered on the tray? If not, readjust it, making sure that the label is facing up. - Is the CD-ROM upside down? If so, turn it right side up so that the label is facing up. - Is the CD-ROM dirty or wet? Clean the CD-ROM with a soft dry cloth (moving from the center to the periphery).
● The mouse is disabled and Windows 95/98 cannot end. Use the keyboard to exit Windows 95/98 as follows: 1 Press the key or the Ctrl + Esc keys. The Start menu appears. 2 Select “Exit Windows” with the ↑ or ↓ key and press the Enter key. The Exit Windows dialog box is displayed. 3 Select “Turn off power” and press the Enter key. Windows 95/98 ends. ● A SCSI unit is connected using a SCSI card but cannot be identified by Windows 95/98.
Appendix This appendix explains how to clean the PC and provides PC main unit specifications. 1 2 3 4 5 Name and Function of Each Component ............................................. 76 Standard Specifications .......................................................................81 Cleaning Method .................................................................................88 Cabinet Security ..................................................................................91 Supplement ...........
Name and Function of Each Component This section provides the name and explains the function of each component of the PC main unit, mother board, and keyboard. Front of the PC main unit ○ ○ ○ ○ ○ ○ Hard disk access indicator lamp The lamp is on while data is being written into or read from a hard disk. Power switch Press this switch to turn on the PC main unit or suspend the system. Power lamp The lamp is on while the PC main unit is on.
Rear of the PC main unit ○ ○ ○ ○ ○ ○ Ventilation holes The heat within the PC main unit is ventilated through these holes. Outlet Connect the power cord of a display. Inlet Connect the power cord of the PC main unit. SPK OUT terminal Connect speakers. Extension slot LINE OUT terminal Connect the input terminal of audio equipment. LINE IN terminal Connect the output terminal of audio equipment. LAN connector Connect the LAN cable. USB connector Connect a USB device.
Inside the PC main unit ○ ○ ○ ○ ○ ○ Extension slot Install various option cards for extending the features of the PC. The PCI card can be inserted. Power supply unit Built-in hard disk IDE-standard hard disk Primary IDE connector A standard-type hard disk is connected. Secondary IDE connector A standard-type CD-ROM is connected.
Motherboard ○ ○ ○ ○ ○ ○ DIMM slots Insert a memory module. The slots are placed in the order of DIMM1 and DIMM2 from the left, as viewed from the front of the PC main unit. CPU 1 3 SW1 dip switch Set whether the password is valid or invalid. To prevent a malfunction, use the switch only to change the password setting. Built-in battery Use this battery to store individual values set with the clock function of the PC and the BIOS setup.
Keyboard ○ ○ ○ ○ ○ ○ Point Unfolding the feet on the bottom of the keyboard permits keyboard inclination.
Standard Specifications PC main unit specifications ○ ○ ○ ○ ○ ○ Product name DESKPOWER 6000/SS CPU Intel Pentium III BIOS ROM 512KB (FLASH ROM) System RAM SDRAM with 168-pin parity (Supporting ECC) Up to 512 MB Floppy disk 3.5-inch disk drive x 1 Hard disk 6.4GB/8.
Product name DESKPOWER 6000/SS Weight About 7.0 kg Outer dimensions 88mm x 330mm x 310mm (W x D x H) (Excluding the foot and (When placed projection section) vertically) Operating environment Temperature: 10 to 35 °C, humidity: 20 to 80% (RH) Point Note that the specifications of the PC main unit may change without prior notice.
LAN adapter specifications ○ ○ ○ ○ ○ ○ ○ LAN controller Intel S82559 Send and receive buffer 3 kB each for send and receive RAM External interface ISO8802-3 100BASE-TX/10BASE-T Transmission media Twisted pair cable*1 (100 Mbps: Category 5, 10 Mbps: Categories 3 to 5) Transmission method Base band Access method CSMA/CD Data transfer speed 100Mbps, 10Mbps Wiring mode Star type Maximum segment 100m length Maximum number of Depends on the hub unit*2 nodes/segment *1 To successfully operate
Resources ○ ○ ○ ○ ○ ○ The following tables list the factory-set statuses of the interrupt request levels (IRQ), DMA channels, and I/O port addresses of the PC.
Connector specifications ○ ○ ○ ○ ○ ○ The pin arrangement and signal names of each connector are as follows: ● Display connector 5 1 10 6 15 11 Pin no.
● Parallel connector 13 1 25 14 Pin no.
● Mouse connector 6 5 4 3 2 1 Pin no. Signal name Direction Description 1 DATA Input/output Data 2 NC – Not connected 3 GND – Ground 4 VCC – Power supply 5 CLK Input/output Clock 6 NK – Not connected ● Keyboard connector 6 5 4 3 2 1 Pin no.
Cleaning Method How to clean the PC is explained as follows: WARNING ● To prevent electric shock, before cleaning the PC, switch off the PC and all connected units and unplug all power cords. Cleaning the PC main unit ○ ○ ○ ○ ○ ○ Wipe the PC main unit with a soft dry cloth. If necessary use a damp cloth but do not permit moisture to come into contact with the PC main unit. Cleaning the keyboard ○ ○ ○ ○ ○ ○ Wipe the keyboard with a soft dry cloth.
2 Remove the ball and clean with water. Reverse the mouse to remove the ball, then clean the ball with water. 3 Clean the inside of the mouse. Wipe the inside of the mouse, the rollers, and the back cover with a damp cloth. 4 Attach the ball and the back cover. After drying the ball and the inside of the mouse, attach the ball and back cover.
Cleaning a CD-ROM drive ○ ○ ○ ○ ○ ○ ○ The lens in a CD-ROM drive for reading data may become dirty after extended periods of use, thereby preventing efficient reading of data from the CD-ROM. Use the CD-ROM cleaning disk to clean the CD-ROM. ● Item to prepare CD-ROM cleaning disk. ● Cleaning method Before using the CD-ROM cleaning disk, remove the plastic ring fixed to the disk. 1 Switch on the PC.
Cabinet Security To protect the devices inside the PC (such as a hard disk and CPU), the cover of the PC can be locked. 1 Remove the upper cover. 2 Pull out and secure the security lock. 3 Attach the upper cover. Thread the security lock through the slit on the rear of the PC main unit. 4 Padlock the cover with the security lock.
Supplement USB ○ ○ ○ ○ ○ ○ The Universal Serious Bus (USB) specifications are used to provide a common interface to peripherals such as mouse, keyboard, printer, modem, and speakers. Point – To use the USB devices with a Windows 95 models, disable the power saving mode. Set “Disabled” to the “Power Management Mode” in the BIOS setup. – The dedicated device driver is to be installed depending on the peripherals supporting the USB. – Operating systems Windows 95/98 support the USB.
Supporting power saving on a display ○ ○ ○ ○ ○ ○ ● For Windows 95 models: To use a display non-supporting the power saving function, open “Display Detailed Properties” on the “Screen Properties” and check off the “Power Saving Display” with the “Monitor” tab. ● Windows 98 models: To use a display non-supporting the power saving function, set “None” to both “System Standby” and “Turning off the Monitor” in the “Power Supply Control Properties”.
Multi-monitor ○ ○ ○ ○ ○ ○ Using the multi-monitor with the refresh rate set to “Optimum” may change the refresh rate after returning from the power saving mode. Set the refresh rate to a value other than “Optimum” and “Adapter fixed value” for each display. LAN cable ○ ○ ○ ○ ○ ○ The LAN incorporated in the PC as standard is compatible with 100BASE-TX/10BASE-T. Check the speed of the network to be connected to your PC and use the following cables in accordance with network speed.
Fujitsu PC (Asia) Pte Ltd 200 Pandan Loop #05-03 Pantech 21 The Computer Centre Singapore 128388 Tel : 65-776 0688 Fax : 65-776 0788 Fujitsu PC (Asia) Pte Ltd (Malaysia Branch) 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur Malaysia Tel : 603-253 3997 Fax : 603-253 4245 Website : www.fujitsu-pc-asia.