P3PC-E177-04EN fi-4860C Image Scanner Installation Guide
INTRODUCTION Thank you for purchasing the fi-4860C Duplex Color Scanner. The fi-4860C is an image scanner designed to scan documents in large quantities. The fi-4860C has the following features. High speed, high quality color scanning capabilities Scans documents of Letter and A4 size at the speed of 60ppm/120ipm @200dpi. Highly reliable document handling Accepts various thicknesses, sizes and types of documents.
The contents of the Operator’s Guide is as follows: 1. BASIC SCANNER OPERATIONS This chapter describes basic scanner operations including basic document scanning. 2. SCANNING VARIOUS TYPES OF DOCUMENTS This chapter describes how to scan various type of documents. 3. DAILY CARE This chapter describes how to clean the scanner. 4. REPLACEMENT OF CONSUMABLES This chapter describes how to replace scanner consumables. 5.
■ Regulatory Information FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Canadian DOC Regulations This digital apparatus does not exceed the Class A limit for radio noise emissions from digital apparatus set out in the Radio interference Regulations of the Canadian Department of Communications. Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescridtes dans le Réglesment sur le brouillage radioélectrique dicté par le ministere des Communications du Canada.
Use in High-safety Applications This product has been designed and manufactured on the assumption that it will be used in office, personal, domestic, regular industrial, and general-purpose applications.
Trademarks Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation of the USA and other respective countries. ISIS, QuickScan and their respective logos are trademarks or registered trademarks of Pixel Translations, a division of Captiva Software Corporation in the United States. Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.
■ Note, Liability READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS. Also, store this manual in a convenient and safe place so that it can be easily referred to during use of this product.
■ Preface Safety Precautions This manual describes important details for ensuring the safe and correct use of this product. Thoroughly read this manual before you start to use this product. In particular, be sure to read and fully understand the Safety Precautions described in this manual before you use this product. Also, store this manual in a convenient and safe place so that it can be easily referred to during use of this product.
Symbols Used In This Manual This manual uses the following symbols in explanations in addition to warning indications. ATTENTION This symbol alerts operators to particularly important information. Be sure to read this information. This symbol alerts operators to helpful advice regarding operation. HINT A TRIANGLE symbol indicates that special care and attention is required. The drawing inside the triangle shows the specific caution.
About Maintenance The user must not perform repairs on this scanner. Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to make repairs to this product. ■ Safety Precautions WARNING The following describes important warnings described in this manual. Do not touch the AC cable with wet hands. Do not touch the power plug with wet hands. Doing so might cause electric shock. Do not damage the AC cable.
Use this scanner only at the indicated power voltage. Do not connect to multiple-power strips. Use this scanner only at the indicated power voltage and current. Improper power voltage and current might cause fire or electric shock. Also, do not connect to multiple-power strips. Wipe any dust from the power plug. Wipe off any dust from metal parts on the power plug or metal fittings with a soft, dry cloth. Accumulated dust might cause fire or electric shock.
Turn the scanner OFF if it is damaged. If the scanner is damaged for any reason, turn off the scanner and unplug the power cable before contacting the store where you purchased the scanner. Do not put liquids inside the scanner. Do not insert or drop metal objects in to the scanner. Do not scan wet documents or document with paper clips or staples. Do not splash or allow the scanner to get wet. If foreign objects (water, small metal objects, liquids, etc.
CAUTION The following describes important cautions described in this manual. Do not install the scanner on unstable surfaces. Install the scanner on a desk so that none of its parts protrude outside of the desktop. Also, make sure that the scanner is installed on a flat, level surface. Do not install the scanner on unstable surfaces. Install the scanner on a level surface that is free of vibration to prevent it from falling.
Before moving the scanner, disconnect the power plug from the power outlet. Do not move the scanner with the power and interface cables connected as this might damage the cables, causing fire, electric shock or injuries. Before moving the scanner, be sure to disconnect the power plug from the power outlet, and disconnect data cables. Also, make sure that the floor is free of obstructions. Protect the scanner from static electricity.
Disconnect the power plug from the power outlet when the scanner is not used for a long period of time. When the scanner is not used for a long period of time, be sure to disconnect the power plug from the power outlet for safety. Do not install the scanner in the direct sunlight. Do not install the scanner in the direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, causing fire or scanner trouble. Install the scanner in a well-ventilated location.
■ Fujitsu Group Offices Please send your comments on this manual or on Fujitsu products to the following addresses: FUJITSU COMPUTER PRODUCTS OF AMERICA, INC. 2904 Orchard Parkway, San Jose, CA ●xvi 95134- FUJITSU CANADA, INC. 6975 Creditview Road Unit 1 Mississauga, On L5N 8E9 Canada 2009, U.S.A. Phone: (1-408)432-6333 Technical Assistance Center: (1-800)626-4686 Fax: (1-408)570-4046 Website: http://www.fcpa.com/ E-mail: info@fcpa.fujitsu.
FUJITSU TAIWAN LTD. FUJITSU HONG KONG LTD. 19th Fl., No39, Sec.1,Chung-hwa Rd., Taipei, Taiwan Phone: (886-2)2311-2255 Fax: (886-2)2311-2277 Website: http://tw.fujitsu.com/ 10/F., Lincoln House, 979 King's Road, Taikoo Place, Island East, Hong Kong Phone: (852)2827-5780 Fax: (852)2827-4724 Website: http://hk.fujitsu.com/ E-mail: scanner@fujitsu.com.hk FUJITSU SYSTEMS BUSINESS (THAILAND) LTD. FUJITSU KOREA LTD. 12th Fl.
●xviii
CONTENTS INTRODUCTION ..................................................................................i ■ ■ ■ ■ ■ Regulatory Information ................................................... iii Note, Liability ................................................................. vii Preface ......................................................................... viii Safety Precautions ..........................................................x Fujitsu Group Offices..........................................
●xx
1 SCANNER BASICS This chapter describes how to prepare the scanner before use. 1.1 Checking the Contents of the Scanner Package.............1-2 1.2 Names and Functions of Parts..........................................1-3 1.3 Operator Panel....................................................................
1.1 Checking the Contents of the Scanner Package When you unpack the scanner package, make sure that all the following parts are included in the package. If any parts are missing or defective, contact to the distributer where you purchased the scanner from. Please handle the scanner and the accessories with care. Scanner and Accessories Scanner Setup CD-ROM Power cable (x1) Adobe® Acrobat® 5.
1.2 Names and Functions of Parts This section describes the names of parts and their functions. ■ Units 12 1 10 13 14 SCANNER BASICS 1 2 19 11 6 7 4 9 8 5 3 19 17 15 18 16 1.
No. Name Function 1 Operator panel Used for operating the scanner. 2 Power button Used to power the scanner on/off. 3 Hopper Document input tray. 4 Side guides Used for adjusting the document width. 5 Hopper extension Used for long documents. 6 ADF (Automatic document feeder) Feeds documents automatically. 7 Pick roller unit Picks top page from document stack. 8 Guide plate The pad assy is mounted on. 9 Pad Assy Separates top page from document stack.
■ Assemblies 1 SCANNER BASICS Lamp unit Removable glass sheetguide Lamp socket cover Lamp PAD Assy Lamp Lamp socket cover Guide plate Brake roller unit Pick roller unit 1.
1.3 Operator Panel (1) The operator panel is located at the Upper right hand side of the scanner. The panel consists of an LCD display (16 characters x 2 line), LEDs, and buttons. ■ Arrangement Power button 1-6 1.
■ Function of Buttons Button Name Function Turns on/off when the main line switch is set to “ | ”. Send to/Start 1 Starts scanning in test mode. Clears the error if this button is pushed while the Check lamp is on or is blinking. Enter Used for setup, or test mode. Exit Used for setup, or test mode. Returns LCD display to “Ready” status. Previous Used for setup, or test mode. Displays the previous menu item when this button is pushed. Used for setup, or test mode.
■ Function of LEDs LED Power Function Lights when the power supply is switched on. (Green) Read Light during scanning. (Green) Check Lights when a hardware alarm is detected. Lights out when button is pushed. (except initial errors) (Yellow) Blinks when an equipment error occurs. Paper jam or Double feed is detected. Press [Stop] button to clear the error, and the LED lights out.
■ Counter display Batch counter and Abrasion counters are shown below: Batch counter L R e a d x y x x x x x x x x x x 1 Abrasion counter K Fig.1 SCANNER BASICS Simultaneously press the both (Left) and (Right) button for at least one second, to switch to the Life counter panel display as shown bellow: Batch counter L R e a d y * x x x x x x x x x x x x x Life counter K Fig.2 To return from “Fig.2” to “Fig.1”, press the both second.
Counter Batch counter Functions (Left) button is pressed for at least one second. The number of scanned documents from the start of reading until "Paper empty" or an error is detected. The counter is automatically reset at the start of next reading. This counter can be used for checking the number of scanned documents per batch. (Right)button This counter is increased by one per sheet. The counter is not re-initialized until the power is turned is pressed for at least one second. off.
2 INSTALLATION AND CONNECTIONS This chapter describes how to install and connect the scanner to a PC, and how to install the Fujitsu application software. References to operating systems (OS) are indicated as follows: Windows 95: Microsoft® Windows® 95 operating system. Windows 98: Microsoft® Windows® 98 operating system. Windows Me: Microsoft® Windows® Millennium Edition operating system. Windows NT 4.0: Microsoft® Windows NT® 4.0 Server operating system, Microsoft® Windows NT® 4.
2.1 Installing the Scanner The following shows the procedure for installing the scanner. ■ Cautions on placement of scanner 1. Move the scanner to the installation area. Refer to the "Operator’s Guide" stored on the “User Manual CD-ROM” about the dimensions of the scanner, and the space required for its installation. ATTENTION Move the scanner with more than two people as it weights approximately 99 lbs (45 Kg). When you move scanner grab it at its bottom. ATTENTION 2-12 2.
2.2 Connecting the Scanner ■ Connecting the power cable Connect the power cable to the power inlet of the device and to a outlet rated to comply with scanner power requirements. 2 An interface cable and a SCSI card are required. Use the following SCSI card to connect to PC.
(1) Use the driver attached to the SCSI card. You can download the driver file for each OS from the following address: • For ASC29160 http://www.adaptec.com/worldwide/support/drivers_by_product.html?sess=no &cat=/Product/ASC-29160 • For ASC39160 http://www.adaptec.com/worldwide/support/drivers_by_product.html?sess=no &cat=/Product/ASC-39160 (2) Install ASPI version 4.70 or later. (For Windows 95, install the ASPI version 4.60.) You can download the driver from the following address.
Product/ASC-29160&filekey=u160_winxp_drv_rc1.exe HINT When connecting the SCSI interface cable, be sure to first connect the SCSI interface cable then turn on the power of the scanner and the PC. Connect the scanner so that it is the last device on the SCSI daisy chain. ATTENTION ATTENTION HINT The SCSI card and SCSI interface cable need to be purchased separately. If the file address at ADAPTEC is changed, go to the ADAPTEC site (http://www.adaptec.com/worldwide/homepage.
1. Connect and use the thumbscrews to secure the interface cable to the interface connector of the scanner. (Back side) Interface connecter 2. Connect and secure the other end of the interface cable to the PC. HINT 2-16 The factory default setting for the scanner’s SCSI ID is “No.5”. If the SCSI ID of another SCSI device is set to the same ID, either change the scanner’s SCSI ID or change the SCSI ID of the other SCSI device. For details on how to change the SCSI ID, refer to the "Chapter 7.
2.3 Installing the Scanner Driver and Application For scanning documents with this scanner, both scanner driver and image capturing application software (called "application" hereafter) must be installed on your PC. Two types of scanner drivers and application are provided for this product.
For Windows 98, Windows Me, Windows 2000, and Windows XP: FUJITSU TWAIN32 V9 For Windows 95: FUJITSU TWAIN32 V8 When using Windows 95: ASPI Manager V4.60 or later is required (generally comes with SCSI board products). • ■ Installing the FUJITSU TWAIN32 Scanner Driver HINT 1. Windows XP screenshots are used in this section. The windows and operations may slightly vary depending on your OS. Turn on the scanner. Press the side of “ | ” on the Main line switch.
Power Button 2 Turn on your PC and log on to Windows. ATTENTION 3. When using Windows NT 4.0, Windows 2000 or Windows XP, log on as a user with "Administrator" privileges (privileges of the administrator of your PC). Otherwise the installation will not be completed correctly. The scanner is detected automatically. [Found New Hardware Wizard] (or [Add/Remove Hardware Wizard) dialog box will appear. 2.3 Installing the Scanner Driver and Application 2-19 INSTALLATION AND CONNECTIONS 2.
Click [Cancel] to close the Wizard window. 4. Insert the Setup CD-ROM into the CD drive. ⇒ appears. This screen may not appear if the "Autoplay" setting of your PC is OFF. In this case, run "Install.exe" in this CD-ROM directly by the "Explorer" or "My Computer". Click [INSTALL PRODUCTS]. 2.
2 Click [TWAIN Driver] on the window below. 2.3 Installing the Scanner Driver and Application 2-21 INSTALLATION AND CONNECTIONS 6.
7. Select a language used for installation on [Choose Setup Language] window and click [OK]. 8. Install the application following the instructions in the window. 9. When the [InstallShield Wiizard Complete] window appears, click [Finish]. 10. Your computer is restarted and the scanner wil be detected. Do not remove the Setup CD-ROM from the CD drive until your PC will be completely restarted. Depending on the OS, the following operations may be necessary.
■ Installing ScandAll 21 Application "Scandall 21" is an image capturing software that complies with the TWAIN standard. With the FUJITSU TWAIN 32 scanner driver, you can capture images using a FUJITSU image scanner fiseries product. ATTENTION Insert the Setup CD-ROM into the CD drive. ⇒ appears. 2. Click [INSTALL PRODUCTS]. 3. Click [ScandAll 21] on the window below. 2.3 Installing the Scanner Driver and Application 2-23 2 INSTALLATION AND CONNECTIONS 1.
4. Select a language used for installation on [Choose Setup Language] window and click [OK]. 5. Install the application following the instructions on the window. 6. When the [InstallShield Wizard Complete] window appears, click [Finish] 2-24 2.
2 To finish the installation, it may be necessary to restart your computer. Follow the instructions in the window. ■ Confirming Installation 1. Set documents on the Hopper. For details on how to load documents, refer to the "1.2 Loading Documents on the ADF for Scanning" in the fi-4860 Operator’s Guide provided in the User Manual CD-ROM. 2. Start ScandAll21 Select [Start] - [Programs] - [Scanner Utility for Microsoft Windows] - [ScandAll 21]. 3. Specify the scanner to use Select [Select Source...
4. Select "FUJITSU fi-4860CEAdij" or "FUJITSU TWAIN32" on the dialog box appeared. HINT For Windows 98, Windows Me, Windows 2000, Windows XP: [FUJITSU fi-4860CEAdij] For Windows 95, Windows NT 4.0: [FUJITSU TWAIN32] 5. Select [To View...] from the [Scan] menu. 6. Set scanning resolution, document size, etc. on the [TWAIN driver] window (for setting details of scanning) and click the [Scan] button. 2-26 2.
2 7. For details on [TWAIN driver], refer to the "FUJITSU TWAIN32 Scanner Driver Help" provided on the Setup CD-ROM Documents are scanned, and the scanned images are displayed on the [ScandAll 21] window. 2.
If the scanning is completed without any troubles, the installation was performed successfully. For details on various types of scanning, refer to the "fi-4860C Operator’s Guide" on the Setup CD-ROM. For FUJITSU ISIS Scanner Driver ■ Preparation Confirm the following items before starting to install the application. • Prepare the Setup CD-ROM at hand. (Do not insert the Setup CD-ROM into the CD drive yet). • Confirm that the scanner is correctly connected to your PC.
Power on ! 2 Main line switch Then press the Power button on the Operator panel. When the power is supplied, the green LED on the Operator panel lights. Power Button 2.
2. Turn on your PC and log on to Windows. ATTENTION 3. When using Windows NT 4.0, Windows 2000 or Windows XP, log on as a user with "Administrator" privileges (privileges of the administrator of your PC). Otherwise the installation will not be completed correctly. The scanner is detected automatically. [Found New Hardware Wizard] (or [Add/Remove Hardware Wizard) dialog box will appear. Click [Cancel] to close the Wizard window. 4. Insert the "Setup CD-ROM" into the CD drive.
5. Click [INSTALL PRODUCTS]. 2 Click [ISIS Driver] on the window below. 2.3 Installing the Scanner Driver and Application 2-31 INSTALLATION AND CONNECTIONS 6.
7. Select a language used for installation on [Choose Setup Language] window and click [OK]. 8. Install the application following the instructions on the window. 9. When the [InstallShield Wiizard Complete] window appears, click [Finish]. 10. Your computer is restarted and the scanner will be detected. Do not remove the Setup CD-ROM from the CD drive until your PC will be completey restarted. Depending on the OS, the following operations may be necessary.
■ Installing QuickScan ProTM Application "QuickScan Pro" is an image capturing software that complies with the ISIS standard. With the FUJITSU ISIS scanner driver, you can capture images using a FUJITSU image scanner fi-series product. ATTENTION Insert the Setup CD-ROM into the CD drive. ⇒ appears. Click [INSTALL PRODUCTS] . 2.3 Installing the Scanner Driver and Application 2-33 2 INSTALLATION AND CONNECTIONS 1. When using Windows NT 4.
3. Click [QuickScan PROTM (Trial)] on the window below. 4. Install the application following the instructions on the window. 2-34 2.
5. Enter required information, then click [Next >] button. 2 6. "QuickScan Pro" included in the Setup CD-ROM is an evaluation version. For further use after expiration of the evaluation period (up to 30 launches), it is necessary to purchase a fully functional version of QuickScan Pro. (When you install the evaluation version, do not change the Serial Number already displayed.) Install the application following the instructions on the window. 2.
■ Confirming Installation Confirm whether or not the scanner works normally as follows. 1. Start QuickScan ProTM. From [Start] menu select [Programs]-[QuickScan]-[QuickScan]. 2. Select [Select Scanner...] from [Scan] menu in QuickScan ProTM. And select fi-4860C from the list of [Scanner:], and then click [OK] button . 3. 2-36 Select [Preview Settings...] from the [Scan] menu. Set the scan resolution, paper size and other scanning conditions, and then click [OK]. 2.
4. Load the documents on the Hopper. 5. For details on how to load documents, refer to "1.2 Loading Documents on the ADF for Scanning" in the fi-4860C Operator's Guide on the User Manual CD-ROM. 6. Select [Preview Scan] from the [Scan] menu. And then the document is scanned. 2 INSTALLATION AND CONNECTIONS If the scanning is completed without any troubles the installation was performed successfully.
Adobe® Acrobat® ■ Installing Adobe Acrobat Install Adobe Acrobat by following the procedure from the "Adobe Acrobat 5.0 CD-ROM" provided with the scanner. HINT 1. Adobe Acrobat is required for displaying the manuals stored on the User Manual CD-ROM. It is also possible to set Adobe Acrobat to display scanned images working together with the scanner. *Installation of Adobe Acrobat is not necessary if it is already installed on your PC. Insert the Adobe Acrobat 5.0 CD-ROM into the CD-ROM drive.
2 The following window appears. Click the [Acrobat 5.0] button, then click the [Install Adobe Acrobat 5.0] button shown below. 2.3 Installing the Scanner Driver and Application 2-39 INSTALLATION AND CONNECTIONS 3.
⇒The 4. The setup window appears. Install Adobe Acrobat by following the instructions in the window. HINT 2-40 Setup window appears and the installation will be started. For details on installation of Adobe Acrobat 5.0, read the description that is displayed by clicking the [Before you install] button in the screen at Operation 3. For details on how to use Adobe Acrobat 5.0, refer to "Adobe Acrobat 5.0 Help." 2.
APPENDIX-1 MESSAGES OF OPERATOR PANEL ■ Massages of Scaner Operation Status (Initializing) (Ejecting document) With progress of time changes to . When the display shows ner changes to the following check states.
P N r o e w p a R r e e a d n i e n w g ! I x n x k x x n g ! x x x x "xxxx" shows the value of the Batch counter. HINT N o w R e a d i "xxxx" shows the value of the Batch counter. HINT ATTENTION AP-2 When the messages on the Operator panel’s LCD have disappeared and only the Power LED lamp stays lit, the scanner is in the Low power mode. To reactivate the scanner from the Low power mode, perform one of the following operations.
(Scanning) The following message is displayed while the scanner is scanning continuously and a double feed has been detected (by checking paper overlapping). When a double feed detection state is canceled on “Ready“ screen after the scanning, the upper row of this message will disappear. S N U o S w D R o e u a b d l i e n g f ! e X e X d X X "xxxx" shows the value the of Batch counter.
(Waiting) The following message is displayed while the scanner is waiting and a double feed (checked by thickness) has been detected. To abort the double feed detection state, press the button, The upper row of this message [Double Feedxxxxx] will blink. D HINT AP-4 o u R b e l a e d F y e x e x d x x x x x x x x x "xxxx"(upper) shows the value of the Batch counter. "xxxxxxxx"(lower) shows the value of the Abrasion or Life counter.
■ Error messages (Temporary errors: Check LED blinking) Check LED blinks when the following errors occur except the and errors. The following messages are displayed if no documents are loaded on the hopper during the scan operation. Please load documents on the hopper. The scanning will be continued, when you load documents on the hopper for re-scanning. To clear this message, press the P a p e button.
The following message is displayed if the ADF cover is not closed completely. Close the ADF cover completely, to enable the scanning. A (by overlapping check) F U S D o v e r O p e n o u b l e f e e d o u b l e F e e d The following message is displayed, when a double feed is detected by paper length check. L C The following message is displayed, when a double feed is detected by paper thickness check.
The following message is displayed, when a document is fed skewed from the hopper to the ADF. I r e g o p p e i c k n a r p a p e r r o v e r l o a d r o o t l l s e e r t u n i t The following message is displayed, when the Pick roller unit is not set correctly during scanning. P l The following message is displayed, when the Pick roller unit is not set correctly.
The following message is displayed, when rotating the Separation roller and the Brake roller does not rotate at all. r AP-8 e l p l a e r r a t w i o o r n n The following message is displayed, when the Abrasion counter value exceeds the setting value for displaying the consumables replacement message.
■ Alarm messages (Hardware errors: Check LED lighting) The following messages are displayed, when an error occurs inside the sccaner. In this case, please switch the scanner off and on again. If the same message is displayed again, please contact to a distributor or an authorized FUJITSU scanner service provider. (Front side) The following message is displayed, when an error occurs at the front side optical unit.
(Front side) The following message is displayed, when the fuse for the lamp for front side blows out.
The following message is displayed, when the hopper moves farther than its correct position. H o p e r o v e r r u n The following message is displayed, when an error occurs in the sensor control part. S p e n s o A r l a C r o m n t r o l The following message is displayed, when an error occurs due to a dirt on the sensor. x x x x S e n s o r d i r t y o r "xxxx.
The following message is displayed, when an error occurs in the Power supply. P D C s o u r p p l y D E D P R R E O S M S A x l x a H r m C 2 R / W E r r o r D T C i m e o u t The following message is displayed, if an error occurs when accessing the Dither/Gamma RAM. i R t / h e W r E / r G r a o m r m a The following message is displayed, if an error occurs during accessing the temporary memory.
The following message is displayed, when an error occurs during downloading the firmware to MDC. M D C E d r o r w o n r l o a d The following message is displayed, when an error occurs in the fi-486PRFR (front-side Imprinter) or the fi-486PRRE (back-side Imprinter).
APPENDIX-2 CONSUMABLES AND REPLACEMENT CYCLE The following table lists the Part No. and the standard replacement cycle of the consumables. It is recommended that you stock extra consumables before the ones in the scanner reaches end of life. The consumables must be replaced periodically.
APPENDIX-3 TROUBLESHOOTING Should any of the following problems arise, refer to the relevant section listed below. Scanner cannot be turned on. Refer to Chapter 5.2 Troubleshooting “Symptom1” of the fi-4860C Operator’s Guide. The operator panel LCD goes out. Refer to Chapter 5.2 Troubleshooting “Symptom2” of the fi-4860C Operator’s Guide. Scanning does not start. Refer to Chapter 5.2 Troubleshooting “Symptom3” of the fi-4860C Operator’s Guide. Quality of scanned pictures and photographs is not satisfactory.
Scanner is not recognized by PC automatically. Refer to Chapter 5.2 Troubleshooting “Symptom13” of the fi-4860C Operator’s Guide. Windows® system gets unstable. Refer to Chapter 5.2 Troubleshooting “Symptom14” of the fi-4860C Operator’s Guide.
APPENDIX-4 CLEARING DOCUMENT JAMS If a document jam occurs during feeding, follow the procedure below to remove the jammed documents. CAUTION - Be careful not to get injured during jam removal. - When removing jammed documents, be careful not to get your neckties or necklaces entangled inside the scanners. - The surface of the glass sometimes becomes hot during operation. Take care not to get burned. ■ Removing jams from the hopper or the transport path 1. Remove the documents on the stacker. 2.
3. While pulling the ADF release lever toward you, lift up the ADF upper sheet guide. ADF upper sheet guide ADF release lever 4. Remove the jammed document. ATTENTION - Staples and paper clips etc. can cause document jams. - Make sure you check the document and the document transport path for obstructions before you start scanning again. - Remove staples and paper clips from the documents before you start scanning. 5. Lower the ADF upper sheet guide carefully. 6.
■ Removing jams from the eject mechanism. 1. Remove the documents on the stacker. 2. Pull up on the lever on the right front of the Upper transport and then raise it. ADF upper sheet guide ADF release lever 3. Pull out the jammed document to the stacker. 4. Lift the Upper transport unit fully to release the safety lock and then lower the transport unit carefully.
■ Document separation force adjustment If the following error occurs frequently, adjust the brake force of the Brake roller using setup mode. - Double-feed - Mis-pick - Paper jam1 1. Enter into the setup mode. Please refer to the section "1.3 Basic Operations of the Operator Panel" on page 6 of the fi4860C Operator’s Guide, "Using the setup and test mode." The following screen appears.
Document separation force setup items are as follows. Setting Document thickness Document separation force "Doublefeed" occurs frequently "Mis-pick" or "Document jam" occurs frequently Increase document separation force Decrease document separation force Thick Thick Strong Medium Thick Medium Thick Medium strong Medium Medium Medium (Factory default setting) Medium Thin Medium Thin Medium Easy Thin Thin Easy If Mis-pick occurs frequently, adjust the Pick roller rotation speed.
AP-22
INDEX A G Abrasion counter ..........................1-10 AC cable.........................................1-2 Accessories ....................................1-2 Adobe Acrobat 5.0 ....................1-2 Installation Guide ......................1-2 Power cable...............................1-2 User Manual ..............................1-2 ADF ................................................1-4 Adobe Acrobat 5.0 .........................1-2 Assemblies .....................................
Power button.................................. 1-4 Power cable ................................... 1-2 Power inlet ..................................... 1-4 Preface........................................1-viii R Regulatory Information .................1-iii Removable sheet guide ................. 1-5 S Safety Precautions ........................ 1-x Scanner Basics .............................. 1-1 Side guides .................................... 1-4 Stacker ...........................................
fi-4860C Image Scanner Installation Guide P3PC-E177-04EN Date of issuance: August, 2003 Issuance responsibility: PFU LIMITED Printed in Japan • Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law. • The contents of this manual are subject to change without notice. • PFU LIMITED.
