User's Manual

4. Peel the film from the Adsorption tape (or paper from the non-cut side of the Double-sided
tape), attach it firmly to the adhesion surface, and then install the Remote Monitoring
Station.
Note the following during installation.
* Install on a flat surface with no irregularities.
* Remove any dirt, water, or oil from the installation location prior to installation.
* Do not attach double-sided tape to locations with weak surfaces such as wallpaper.
* When double-sided tape is removed it may leave a mark. If using a chemical such as an adhesive
remover to clean the surface, make sure that it will not cause any damage.
■ Safety Notes
This section includes important information in order to use this product safely and correctly. Be sure to read this
information prior to using this product, so that it can be used correctly, safely, and appropriately. Be sure to read
the manual carefully in order to use the product correctly.
Common notes for UBIQUITOUSWARE products
DANGER
Always be sure to turn this product off
prior to entering areas (such as gasoline
stands) with flammable gas (such as
propane gas or gasoline) or dust. Do not charge the
product in these areas.
Doing otherwise could cause the gas to ignite.
WARNING
Use indicated peripheral devices only.
Doing otherwise could cause heat buildup,
ignition, an explosion, a malfunction, or
leaking.
Do not subject the product to strong
forces, drop it, drive nails through it,
hammer it, or step on it.
Doing otherwise could cause ignition, damage, or
injury.
Do not place this product in fire, heat
it, or short the terminals.
Doing otherwise could cause smoke,
ignition, or an explosion.
If this product behaves abnormally (such
as heat buildup, emitting smoke or
strange odors/noises), immediately
remove it from your wrist and turn the power off.
If the product is connected to its AC adapter,
remove the power plug from the outlet.
Continuing to use this product when it is acting
abnormally could cause electrical shock or a fire.
If a liquid (such as water) or a foreign
substance (such as metal) enters this
product, immediately turn the product
off. If the product is connected to its AC adapter,
remove the power plug from the outlet.
Continuing to use it in this state could cause
electrical shock or a fire.
If this product is dropped or parts such
as its cover are damaged, immediately
turn the product off and repair it.
Continuing to use it in this state could cause
electrical shock or a fire.
If you hear thunder, do not touch this
product or its cables until there is no
danger of lighting striking.
Do not connect any cables as long as there is a danger
of lighting striking. If there is a danger of
lighting striking, turn this product off beforehand
and immediately remove the product from your wrist.
If the product is connected to its AC adapter, remove
the power plug from the outlet and then detach the
cables.
Doing otherwise could result in being shocked by
lightning or could cause a fire. The product could
also malfunction.
Never disassemble or modify this product
yourself.
Doing otherwise could result in injury,
electrical shock, or a fire.
When using this product, do not cover it
with a blanket or other covering, place
it near a heater, or place it on an
electric carpet.
Doing otherwise could trap heat inside the product,
causing a fire.
Do not use cleaning sprays (that include
flammable substances) to clean this
product.
Doing otherwise could result in a malfunction or
fire.
If this product is damaged and the main unit’s
internals are exposed due to dropping it or the like,
do not touch the exposed internals.
Doing otherwise could cause electrical shock or
Store the main unit and its accessories
outside the reach of infants.
Do not allow infants to chew or swallow the
main unit or its accessories.
If an infant should swallow the main unit
or its accessories, consult immediately
with a physician.
Use only included or specified AC adapters
or power cables with this product; do not
use the included AC adapter or power cable
with other products.
Doing otherwise could cause an electrical shock or
fire.
CAUTION
Do not wipe with benzine or paint
thinner.
Doing otherwise could cause paint
peeling, cracking, injury caused by damage, or a
fire.
If this product is dirty or wet, wipe it
clean with a dry cloth or the like.
If left dirty or wet the product could
deteriorate more quickly or its color could fade.
Do not place heavy objects on this
product.
Doing otherwise could cause damage or
injury.
Do not use or place this product in
locations that are subject to direct
sunlight or that are very hot (such as in
locked vehicles).
Doing otherwise could cause an electrical shock or
fire. It could also result in damage or a
malfunction.
AC Adapter, Power cable
WARNING
Use only at the specified power supply
voltage.
Failure to do so could cause ignition,
fire, heat buildup, or electrical shock.
Do not connect to devices that generate
square waves (uninterruptible power
supplies (UPS) or automobile AC power
supplies).
Doing otherwise may result in a fire.
Make sure that the power plug is firmly
inserted all the way into the outlet.
If the connection is not good it could
cause electrical shock, heat buildup, or ignition
that could result in a fire. Do not use any loose
outlets.
Insert the AC adapter power plug directly
and firmly into the outlet (100 V AC). Do
not use piggybacked electrical outlets.
Doing otherwise could cause electrical shock, burns,
or fire.
Hold the AC adapter or power cable straight
when inserting or removing them. Do not
apply unreasonable force.
Doing otherwise could cause fire, burns, injury, or
electrical shock.
When removing the AC adapter power plug
from the outlet, be sure to grab the AC
adapter. Do not pull the power cable.
Pulling the power cable could damage it, causing
electrical shock or fire.
Place the product near the outlet in an
accessible location where the power plug
can easily be reached.
Doing otherwise could make it impossible to remove
the power plug or could lead to danger.
injury due to the damaged part.
Store bags and the like used for the
packaging material outside the reach of
children.
Doing otherwise could result in suffocation if the
child puts the material in his or her mouth or covers
his or her head with it.
Do not insert or remove the power cable or
AC adapter if your hands are wet.
Doing otherwise could cause electrical
shock.
Do not wrap the power cable tightly around
the AC adapter, or otherwise apply
pressure to the base.
Doing otherwise could expose or sever the core of the
power cable, causing electrical shock or fire.
When the AC adapter is connected to the
outlet, do not catch anything on it or
otherwise subject it to strong impact.
Doing otherwise could cause injury or a malfunction.
Do not drop the AC adapter or subject it
to strong impact. Doing otherwise could
damage the internal circuit board. Do not
use deformed, broken, or damaged AC adapters or power
cables.
Doing otherwise could cause a malfunction,
electrical shock, or fire.
Periodically remove the AC adapter or
power plug from the outlet, and use a soft
cloth to clean dust from the connecting
parts of the outlet, AC adapter, and power cable.
Using the product when these are dusty could cause
electrical shock, burns, or fire. Inspect and clean
the product once per year.
Always remove the AC adapter power plug
from the outlet during maintenance.
Doing otherwise could cause electrical
shock.
Never use in bathrooms or other highly
humid locations.
Doing otherwise could cause electrical
shock or a malfunction.
If the product will not be used for a long
period of time, remove the AC adapter
power plug from the outlet and disconnect
the AC adapter.
Doing otherwise could cause a fire.
Do not use damaged AC adapters, power
cables, or power plugs.
Doing otherwise could cause fire or
electrical shock.
Do not bring screwdrivers or other metal
objects near the AC adapter power plug.
Doing otherwise could cause fire or
electrical shock.
Do not damage, modify, heat, or pull the
power cable. Do not place heavy objects on
it, or bend or twist it unreasonably. Do not
use damaged cables.
Doing otherwise could cause electrical shock, a short
circuit, fire, or burns.
Radio components
WARNING
Precautions on WLAN and
Bluetooth
®
wireless technology
Turn wireless communication
functions off (for example, turn the product
off) in the following locations.
・Inside hospitals or in locations with
electronic medical devices
Be especially careful not to bring the
product into operating rooms, intensive
care units, CCUs (coronary care units), or
other similar locations.
・Locations where the use of wireless
communication functions is prohibited,
such as on airplanes
・Near automatic control devices such as
automatic doors or fire alarms
・Locations where you may come into close
contact with individuals who are wearing
implantable medical devices (such as
pacemakers) in the situation where you
cannot move freely, etc.
■ Disposal
CAUTION
For commercial customers who have purchased the product from us, refer to “Disposing
and Recycling ICT Products” on our webpage
(http://www.fujitsu.com/jp/about/environment/society/products/recycleinfo/). If this
product was obtained from another source, please contact that source.
■ Additional Information
□ Precautions for use
・This product uses wireless communication, and there may be cases where functions may not be used
as expected if there is cross talk or interference. We are not to be held responsible for incidents,
accidents, or damage caused through use of this product.
・If the status LED turns red, a sensor malfunction or communication error may have occurred. If this
occurs, please contact the source this product was obtained from.
・A smartphone (Android 4.4 or later) and special application are required to initialize this product.
・No personal information is stored in this product.
・This product cannot be used if it is not turned on.
・Place one hand on the Remote Monitoring Station to stabilize it when pressing buttons. Doing otherwise
could cause the adhesion side of the stand to come unstuck, making it impossible to press buttons.
・The wireless LAN IEEE 802.11b unit installed in the Remote Monitoring Station can use wireless
channels 1 through 13. Set the wireless LAN access point to use a channel within the range from
1 to 13. Please refer to your wireless access point manual for information on how to configure
it.