Operating manual FUJITSU LIFEBOOK T734 System
Congratulations on your purchase of an innovative product from Fujitsu. The latest information about our products, tips, updates etc. can be found on the Internet at: "http://www.fujitsu.com/fts/" You can find driver updates at: "http://support.ts.fujitsu.com/download" Should you have any technical questions, please contact: • our Hotline/Service Desk (see the Service Desk list or visit: "http://support.ts.fujitsu.
Published by / Contact address in the EU Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 Munich, Germany "http://www.fujitsu.com/fts/" Copyright © Fujitsu Technology Solutions 2013. All rights reserved. Publication Date 11/2013 Order No.
FUJITSU LIFEBOOK T734 Operating manual Innovative technology 7 Ports and controls 9 Important notes 12 First-time setup of your device 15 Working with the notebook 18 Security functions 68 Connecting external devices 75 Removing and installing components during servicing 81 Settings in BIOS Setup Utility 89 Troubleshooting and tips 91 Technical data 98 Manufacturer’s notes 102 Index 108
Remarks Information on the product description meets the design specifications of Fujitsu and is provided for comparison purposes. Several factors may cause the actual results to differ. Technical data is subject to change without prior notification. Fujitsu rejects any responsibility with regard to technical or editorial mistakes or omissions. Trademarks Fujitsu, the Fujitsu logo and LIFEBOOK are registered trademarks of Fujitsu Limited or its subsidiaries in the United States and other countries.
Contents Contents Innovative technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Further information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notational conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing a module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing a module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optical drive . . . . . . . . . .
Contents HDMI port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting USB devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB port with charging function (Anytime USB charge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to remove USB devices correctly . . . . . . . . . . . . . . . . . . .
Contents Notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Port Replicator (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Rechargeable battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Innovative technology Innovative technology ... and ergonomic design make your device a reliable and convenient companion. The device boots very quickly, is ready for immediate use and offers a particularly long operating time because of its high capacity battery. With the user-friendly "BIOS Setup Utility" you can control your notebook’s hardware and better protect your system against unauthorised access by using the powerful password properties.
Innovative technology Notational conventions Pay particular attention to text marked with this symbol. Failure to observe these warnings could pose a risk to health, damage the device or lead to loss of data. The warranty will be invalidated if the device becomes defective through failure to observe these warnings. Indicates important information for the proper use of the device.
Ports and controls Ports and controls This chapter presents the individual hardware components of your device. It gives you an overview of the device’s indicators and connections. Please familiarise yourself with these components before you start to work with the device.
Ports and controls Left panel 1 2 1 = DC input connector (DC IN) 2 = HDMI port 3 3 = USB port with charging function (Anytime USB charge, USB 3.0) Rear 1 1 = Security Lock device 2 = VGA monitor port 10 2 3 4 3 = USB ports (USB 2.
Ports and controls Right-hand side 1 3 2 4 3 = Module bay with optical drive 4 = Eject lever for module bay 1 = Pen slot 2 = ExpressCard slot Bottom 1 2 3 7 6 1 2 3 4 = = = = Hard disk service compartment Memory service compartment Attachment eye for the pen cord Battery with SIM card slot under the battery Fujitsu 5 4 5 = Battery charge status indicator 6 = Port for port replicator 7 = Ventilation slot cover 11
Important notes Important notes Notes Importantnotes This chapter contains essential safety information which must be followed when working with your notebook. Other notes also provide useful information which will help you with your notebook. Safety notes Notes Safetynotes Please follow the safety notes provided in the "Safety/Regulations" manual as well as the safety notes given below. Please pay special attention to the sections in the manual marked with the symbol on the left.
Important notes Energy saving Energysaving Energy Notes Switch the notebook off when it is not in use. Switch off external, connected devices if you are not using them. If you use the energy saving functions, the notebook uses less energy. You will then be able to work for longer before having to recharge the battery. Energy efficiency is increased and the environmental impact is reduced. You save money while protecting the environment.
Important notes Notebook: transporting Protect the notebook from severe shocks and extreme temperatures (e.g. direct sunlight in a car). ► ► ► ► ► ► If your device has an optical drive, remove all data media (e.g. CD, DVD) from the drives. Switch the notebook off. Unplug the mains adapter and all external devices from the power socket. Disconnect the mains adapter cable and the data cables for all external devices. Close the LCD screen.
First-time setup of your device First-time setup of your device Gettingstarted First-timesetup Please read the chapter "Important notes", Page 12. If your device is equipped with a Windows operating system, the necessary hardware drivers and supplied software are already pre-installed. Before you switch on the device for the first time, connect it to the mains voltage using the mains adapter, see "Mains adapter connecting", Page 16.
First-time setup of your device Selecting a location Selectinga location Mainsadapter Device Select a suitable location for the device before setting it up. Follow the instructions below when doing so: • Never place the device or the mains adapter on a heat-sensitive surface. The surface could be damaged as a result. Never place the device on a soft surface (e.g. carpeting, upholstered furniture, bed). This can block the air vents and cause overheating and damage.
First-time setup of your device Switching on the device for the first time Switchingon for thefirsttime On devices with ON/OFF switch for wireless components: Slide the ON/OFF switch for wireless components to the ON position before switching on the device. When you switch on the device for the first time, the supplied software is installed and configured.
Working with the notebook Working with the notebook Notebook Notebook,operation This chapter describes the basics for operating your notebook. Please read the chapter entitled "Connecting external devices", Page 75 for instructions on how to connect devices such as a mouse and a printer to the notebook. Please refer to the notes in "Important notes", Page 12.
Working with the notebook Status displays Description Power-on indicator • Indicator is illuminated: The notebook is switched on. • Indicator flashes: The notebook is in sleep mode (Save-to-RAM). • The indicator is not illuminated: The notebook is switched off or in Save-to-Disk mode. Battery charging indicator The battery charging indicator shows whether a battery is installed and being charged. Battery indicator This description applies for both batteries.
Working with the notebook Opening the notebook ► Open the LCD screen.
Working with the notebook Switching on the notebook Notebook:switching on Suspend/Resumebutton Power-onindicator 1 ► Slide the ON/OFF switch (1) to the right to switch on the notebook. The ON/OFF switch returns automatically to its original position. The ON/OFF switch (1) lights up whenever the system is switched on. Programming the ON/OFF switch You can program the ON/OFF switch: Operating system Windows 7 Windows 8.
Working with the notebook Different ways to use your notebook During your daily work, you can use your notebook as a tablet PC or as a notebook, just as you wish. Note the direction of rotation in the following description! No guarantee claims can be met for damage caused by turning in the wrong direction. You must note that the display cannot be turned completely on its own axis! From notebook to Tablet PC ► Raise the LCD display into a vertical position.
Working with the notebook ► Hold the screen as low as possible on both sides. Turn the screen to the left or right in the direction of the arrow. At first you will feel some slight resistance, then it will turn easily and without friction. ► Turn the display further until it has turned 180° and the hinge latches in.
Working with the notebook ► Now fold the screen down until the back of the screen is flat on top of the keyboard. The screen is now secured in the tablet position. Select display orientation (portrait or landscape orientation) Displayorientation Portraitorientation Landscapeorientation You can choose to use either portrait or landscape orientation for the display.
Working with the notebook From Tablet PC to notebook ► Raise the LCD screen into a vertical position.
Working with the notebook Note the direction of rotation in the following description! No guarantee claims can be met for damage caused by turning in the wrong direction. ► hold the screen as near to the bottom as possible on both sides and turn the screen in the direction indicated by the rotational direction indicator. It will turn easily and without resistance. ► Turn or move the display further until it has turned 180° and the hinge latches in.
Working with the notebook Closing the notebook ► Fold the LCD screen down onto the lower part of the notebook until you feel it lock into place. Handwriting recognition For detailed information on handwriting recognition, see the documentation on your operating system. At present, handwriting recognition under Windows 7 or Windows 8.
Working with the notebook LCD screen Notes LCDscreen Fujitsu notebooks have high-quality LCD monitors (TFT). For technical reasons, these monitors are manufactured for a specific resolution. An optimal, clear picture can only be ensured with the resolution intended for the relevant monitor. A resolution which differs from the specification can result in an unclear picture. The resolution of your notebook’s monitor is optimally set at the factory.
Working with the notebook Using a device as a tablet PC You can execute commands as follows: • • using the stylus pen (supplied with your device). using your fingers Using fingers You can execute certain commands by using your finger tip on the touchscreen of your device. Everything which you can select or activate using your finger tip can also be selected or activated using the stylus pen. Calibrate the Dual Digitizer for finger-based operation of the device.
Working with the notebook Actions with one finger Action Selecting objects (click with the left mouse button) Starting programs (double-click with the left mouse button) Moving objects/windows (drag with left mouse button pressed, Drag & Drop) Opening a context menu (click with the right mouse button) Moving the cursor 30 Description ► With your finger, tap once briefly on the object. ► With your finger, tap twice briefly in quick succssion on the program icon.
Working with the notebook Actions with two fingers Action Scrolling Description ► Position two fingers on the touchscreen. ► Move your fingers upwards to scroll up. or ► Move your fingers downwards to scroll down.
Working with the notebook Action Rotating Description ► Position the thumb on the touchscreen, then turn the picture clockwise or counter-clockwise using your index finger.
Working with the notebook Action Increasing or decreasing the view Description ► Position two fingers on the touchscreen and move them apart to increase the view. or Blocking context-sensitive menus Fujitsu ► Position two fingers on the touchscreen and move them together to decrease the view. ► With two fingers, tap twice briefly in quick succession on the touchscreen.
Working with the notebook Using the stylus pen 1 = pen tip 3 4 2 = rocker button 3 = eyelet for pen cord 4 = eraser 2 1 You can use the pen on your notebook as an electronic writing implement to select items and to navigate through menu options and programs. Programs that support handwriting recognition also allow you to write characters directly on the screen with the pen. You can also use the pen as a drawing tool. The notebook pen is retained securely in the pen slot.
Working with the notebook The pen of your notebook is an electronic instrument which can be damaged if used incorrectly. Handle the pen with care. The following list contains guidelines for proper pen handling: • • • • Do not gesture with the pen. Do not use the pen as a pointer. Never use the pen on any other surface than the screen of your notebook. Do not try to turn the thumb grip on the pen. The thumb grip is used to place the pen in its slot and to take it out of the slot.
Working with the notebook Calibrating the pen If Windows 8.1 is installed on your Tablet PC, your Tablet PC is already calibrated at initial setup. If a different operating system is installed on your Tablet PC, you must calibrate it with the pen before first use, so that it recognises the pen as accurately as possible. You should also always repeat the calibration if the co-ordination between the pen and cursor movement deteriorates. Operating system Windows 7 / Windows 8.
Working with the notebook Using the device as a notebook Touchpad and touchpad buttons Keep the touchpad clean. Protect it from dirt, liquids and grease. Touchpad Do not use the touchpad if your fingers are dirty. Do not rest heavy objects (e.g. books) on the touchpad or the touchpad buttons. 1 = Touchpad 1 2 = Touchpad buttons 2 The touchpad enables you to move the mouse pointer on the screen. The touchpad buttons allow you to select and execute commands.
Working with the notebook Dragging items ► Select the desired item. ► Press and hold the left button and, with your finger on the touchpad, drag the item to the desired position. The item will be moved. Touchpad Switching the Touchpad on and off You can switch the Touchpad on and off using a key combination, see "Key combinations", Page 41.
Working with the notebook Keyboard Keyboardkeypad Numeric Buttons The keyboard of your notebook is subject to continuous wear through normal use. The key markings are especially prone to wear. The key markings are liable to wear away over the life of the notebook. The keyboard has been designed to provide all the functions of an enhanced keyboard. Some enhanced keyboard functions are mapped with key combinations. The following description of keys refers to Windows.
Working with the notebook Key Description Backspace key The Backspace key deletes the character to the left of the cursor. Backspace Tab key The Tab key moves the cursor to the next tab stop. Tabkey Enter key (return) The Enter key terminates a command line. The command you have entered is executed when you press this key. Linefeed Enter Return Enterkey Caps Lock key The Caps Lock key activates uppercase mode. In Caps Lock mode, all of the characters you type appear in upper case.
Working with the notebook Virtual numeric keypad Numeric Num Virtualnumerickeypad Lock keypad To provide the convenience of a numeric keypad, your keyboard is equipped with a virtual numeric keypad. The special keys of the virtual numeric keypad are recognisable by the numbers and symbols printed in the upper right corner of each key. If you have switched on the virtual numeric keypad, you can output the characters shown on the upper right of the keys.
Working with the notebook Combination Description Switching the loudspeakers on/off This key combination switches the integrated loudspeakers on and off. Loudspeaker Fn+F3 Enable/disable touchpad This key combination enables and disables the touchpad. Touchpadbuttons Touchpad Fn+F4 Decrease screen brightness This key combination decreases the brightness of the screen. Screenbrightness LCDscreen Fn+F6 Increase screen brightness This key combination increases the brightness of the screen.
Working with the notebook Combination Ctrl + C Description Halt current operation This key combination can be used to halt an operation instantly without clearing the keyboard buffer. Back tab This key combination moves the cursor back to the previous tab stop. Tabback Shift+Tab Tablet buttons Your notebook has six multifunctional tablet buttons. You can navigate on the screen with a simple press of a button, call preset applications or ones that you have set yourself.
Working with the notebook Basic functions when the device has booted Button Basic function Windows button This button corresponds to the function of the Windows Start key on a keyboard. If the button is pressed in combination with the ON/OFF switch, the function corresponds to the key combination Ctrl + Alt + Del . Decrease volume This button reduces the volume of the built-in loudspeakers. Increase volume This button increases the volume of the built-in loudspeakers.
Working with the notebook Webcam Webcam Depending on the software used, you can use your Webcam to take pictures, record video clips or take part in web chats. • • • • The picture quality depends on the lighting conditions and the software being used. You can only operate the webcam with a particular application (e.g. an Internet telephony program or a video conferencing program which supports a webcam). When using the webcam the notebook support must not wobble.
Working with the notebook Rechargeable battery Life,battery Battery Rechargeablebattery When not plugged into a mains socket, the notebook runs on its built-in battery. You can increase the life of the battery by caring for the battery properly. The average battery life is around 500 charge/discharge cycles. You can extend the battery life by taking advantage of the available energy saving functions.
Working with the notebook Removing and installing the battery Only use batteries approved by Fujitsu for your notebook. Never use force when fitting or removing a battery. Make sure that no foreign bodies get into the battery connections. Never store a battery for long periods in the discharged state. This can make it impossible to recharge. Removing the battery ► Prepare for removal, see chapter "Preparing to remove components", Page 82. 1 2 3 ► Slide the release button (1) in direction of the arrow.
Working with the notebook Inserting battery 3 2 1 ► ► ► ► 48 Place the battery on the lower edge of the battery compartment (1). Slide the battery into the battery compartment until you feel it engage (2). Slide the release button into its locked position (3). Complete the removal, see chapter "Finishing component removal", Page 88.
Working with the notebook Battery charge status indicator You can check the charge status directly on the battery itself. a 1 ► Press the key (1). The LED (a) lights up in one of the following colours: LED indicator Green Orange Red LED not lit Fujitsu State of charge The battery is between 50 % and 100 % charged. The battery is between 11 % and 49 % charged. The battery is between 1 % and 10 % charged. The battery is fully discharged.
Working with the notebook Module Modules Modulebay The design of your notebook enables the flexible use of notebook batteries and drives. The following modules can be operated in the module bay of your notebook: • • • Second battery Optical drive Empty plug-in unit (save weight) Only use modules designed for your notebook. Do not use force when installing or removing the module. Make sure that no foreign objects enter the module bay. You can swap modules during operation.
Working with the notebook Installing a module ► Place the module into the module bay so that the contacts enter first. ► Push the module into the module bay until you feel it locking into place. Optical drive Opticaldrive This product contains a light emitting diode, classification according to IEC 60825 1:2007: LASER CLASS 1, and must therefore not be opened.
Working with the notebook CD/DVD indicator CD/DVDindicator The CD/DVD indicator flashes when a data carrier is inserted. The indicator goes out when the drive is ready for reading. The indicator lights up when the drive is being accessed. You may only remove the data carrier when the indicator is unlit. If the CD/DVD indicator does not go out after a data carrier has been inserted, but instead continues to flash, this means that the drive cannot access the data carrier.
Working with the notebook Manual removal (emergency removal) Emergencyremovalofdata carrier Manualremovalofdatacarrier CD/DVD: In the event of a power failure or damage to the drive, you can remove the data carrier manually. ► Switch your notebook off. ► Push a pen or a piece of wire (such as a paperclip) firmly into the opening (1). The drive tray is ejected. You can now pull the drive tray (2) out of the drive.
Working with the notebook ► Insert the ventilation slot cover into the slot (1) at an angle as shown, and ensure that you feel it click into place. ► Complete the removal, see chapter "Finishing component removal", Page 88.
Working with the notebook Using the power-management features Battery Power The notebook uses less power when the available power-management features are used. You will then be able to work longer when using the battery before having to recharge it. Power efficiency is increased and environmental pollution reduced. By choosing the best power options, you can make significant savings and at the same time help protect the environment.
Working with the notebook Memory cards Slot Your notebook is equipped with an integrated memory card reader. Observe the manufacturer’s instructions when handling the memory cards. Memory card Supported format The memory card reader supports the following format: • Secure Digital (SDTM card) Inserting the memory card ► Carefully slide the memory card into the slot. The label should be facing upward. Do not apply excessive force, as otherwise the delicate contact surfaces could be damaged.
Working with the notebook ExpressCards ExpressCard Slot An ExpressCard slot allows an ExpressCard/54 to be used with the computer. Consult the documentation supplied by the ExpressCard’s manufacturer and follow the instructions provided. Never use force when installing or removing an ExpressCard. Make sure that no foreign objects enter the ExpressCard slot. Inserting the card Keep the placeholder for the slot in a safe place. When you remove the card again, you must reinstall the place holder.
Working with the notebook Removing the card To avoid any loss of data, always follow the correct procedure for removing the card (see the documentation for your operating system). ► Press the edge of the card (1) so that the card protrudes a little from the notebook. ► Pull the card out of the slot (2). 1 2 ► Insert the card placeholder into the slot guide. ► Gently slide the card placeholder into the slot until you feel it click into place.
Working with the notebook SIM card A SIM card (Subscriber Identity Module) is a chip card which is inserted in a mobile phone or notebook and, together with an integrated UMTS/LTE module, enables access to a mobile network. When handling SIM cards, follow the instructions supplied by the provider. Inserting the SIM card ► Prepare for installation of the SIM card, see chapter "Preparing to remove components", Page 82.
Working with the notebook Optional Wireless LAN / Bluetooth / UMTS / LTE wireless components The installation of radio components not approved by Fujitsu will invalidate the certifications issued for this device. Depending on the device configuration you ordered, your device will be equipped with Wireless LAN, Bluetooth, UMTS or LTE. Switching the wireless components on and off Before switching on your device for the first time, the on/off switch for radio components must be in the "ON" position.
Working with the notebook Setting up WLAN access • Requirement: A WLAN must be available and you must have the corresponding access information. Information on configuring the WLAN access can be found in the documentation for your operating system. Access via UMTS / LTE If you ordered an integrated UMTS / LTE module with your system, you can enjoy optimum reception and maximum energy efficiency without awkward cables or antennas. The optional UMTS / LTE module is ready for use straight away.
Working with the notebook Ethernet and LAN EthernetLAN The internal network module of your notebook supports Ethernet LAN. You can use it to establish a connection to a local network (LAN = Local Area Network). ► Connect the network cable to the LAN port of the notebook (1). ► Connect the network cable to your network connection (2). 1 2 Your network administrator can help you to configure and use the LAN connections. The network cable is not included in the delivery scope.
Working with the notebook Your Port Replicator (optional) Your Port Replicator is a device that enables you to quickly connect your notebook to your peripherals, such as a monitor, printer etc. The features offered by the Port Replicator include standard ports for monitor, audio, mouse and keyboard. You need only dock the notebook in order to use your peripheral devices.
Working with the notebook Setting up the port replicator Select a suitable location for the port replicator before setting it up. Follow the instructions below when doing so: • • • • 64 Never place the port replicator on a soft surface (e.g. carpeting, upholstered furniture, bed). This can block the air vents of the notebook and cause overheating and damage. Place the port replicator on a stable, flat and non-slip surface.
Working with the notebook Connect the notebook to the port replicator The Port Replicator supports various LIFEBOOK models. The adjusting lever of the Port Replicator can be used to adapt the Port Replicator to the size of the particular LIFEBOOK. Before connecting the notebook to the port replicator, check if the setting lever of the port replicator is in the right position. If necessary, adjust the setting lever to the correct position.
Working with the notebook Switching on the notebook via the port replicator ► Press the ON/OFF switch on the port replicator to switch the notebook on. Switching off notebook via Port Replicator ► Close all applications and shut down your operating system (please refer to the manual for the operating system). If the notebook cannot be shut down properly, press the ON/OFF button on the Port Replicator for approx. four seconds. The notebook will switch off. Any unsaved data may however be lost.
Working with the notebook Disconnecting the notebook from the port replicator Problems may occur if the notebook is removed from the port replicator during operation. We recommend that you switch off the notebook beforehand or use the Windows function Start – Undock. Windows 7 Problems may occur if the notebook is removed from the port replicator during operation. We recommend that you switch off the notebook beforehand or use the Windows function Start (arrow icon) – Undock.
Security functions Security functions Securityfunctions Your notebook has several security features that you can use to secure your system from unauthorised access. This chapter explains how to use each function, and what the benefits are. Please remember that in some cases, for example, forgetting your password, you may be locked out and unable to access your data.
Security functions Configuring the fingerprint sensor Fingerprintsensor The fingerprint sensor can record an image of a fingerprint. With additional fingerprint software, this image can be processed and used instead of a password. ► You must install the fingerprint software in order to be able to use the fingerprint sensor (1). 1 Using the Security Lock Your device comes with a Security Lock device for the Kensington Lock Cable.
Security functions Configuring password protection in BIOS Setup Utility Before using the various options for password protection in the BIOS Setup utility to increase data security, please observe the following: Make a note of the passwords and keep them in a safe place. If you forget your supervisor HDD password you will not be able to access your notebook. Passwords are not covered by your warranty and a charge will be made for assistance.
Security functions Changing the supervisor or user HDD password You can only change the supervisor HDD password if you have logged into the BIOS Setup Utility with the supervisor HDD password. User HDDpassword SupervisorHDDpassword Password ► Call the BIOS Setup Utility and go to the Security menu. ► When changing the password, proceed exactly as for password assignment.
Security functions Password protection for the hard disk Passwordprotection: The hard disk password prevents unauthorised access to the hard disk drives and is checked internally each time the system is booted. The requirement is that you have set at least the supervisor HDD password. Activating hard disk protection ► Call up the BIOS Setup and select the Security menu.
Security functions Using the security function of the tablet keys If you have set a supervisor and/or user HDD password in the form of tablet key combinations as described below, you can use the tablet keys to enter this when you start your device. Setting the Supervisor password ► Select Start - Run. ► Enter the following at the command line: C:\Program Files\Fujitsu\Security Panel Application\Supervisor\FJSECS.EXE. ► Confirm with Enter . ► Follow the instructions on the screen.
Security functions Trusted Platform Module (TPM) (device-dependent) Trusted Platform Module TPM To use the TPM, you must activate the TPM in the BIOS Setup before the software is installed. The condition for this is that you have assigned at least the supervisor HDD password (see "Security functions", Page 68). Enabling TPM • ► ► ► Requirement: You have set a supervisor HDD password, see "Security functions", Page 68. Call up the BIOS Setup and select the Security menu.
Connecting external devices Connecting external devices Always refer to the safety information provided in "Important notes", Page 12 before connecting or disconnecting any devices to or from your notebook. Always read the documentation supplied with the device you wish to connect. Never connect or disconnect cables during a thunderstorm. Never pull at a cable when disconnecting it. Always grasp the plug.
Connecting external devices Connecting an external monitor The Port Replicator, available as an option for your notebook, offers you a DVI port and a DisplayPort. An analogue monitor is connected to the analogue VGA monitor port, a digital monitor to the DVI-I monitor port of the port replicator. Screen output is limited to a maximum of two screens at any one time (see "Key combinations", Page 41, section "Toggle output screen").
Connecting external devices Connecting an external monitor to the DisplayPort It is possible to connect a digital monitor to the DisplayPort on the port replicator. Screen output is limited to a maximum of two screens at any one time (see "Key combinations", Page 41, section "Toggle output screen"). Digital DisplayPort ► Switch off the notebook and the external monitor. ► Plug the data cable of the external monitor into the monitor port. ► First switch on the external monitor and then the notebook.
Connecting external devices Connecting USB devices USBports On the USB ports, you can connect external devices that also have a USB port (e.g. a DVD drive, a printer, a scanner or a modem). USB devices are hot-pluggable. This means you can connect and disconnect devices while your operating system is running. USB 1.x has a maximum data transfer rate of 12 Mbit/s. USB 2.0 has a data transfer rate of up to 480 Mbit/s. USB 3.0 has a data transfer rate of up to 5 Gbit/s.
Connecting external devices USB port with charging function (Anytime USB charge) USBchargingfunction It is recommended that the notebook be operated with the power supply connected whenever the USB port with charging function is in use, as this function will drain the battery more quickly if an external USB device is being charged.
Connecting external devices Connecting external audio devices Microphone port/Line In Microphone,connecting Audioports Audiodevices,connecting The microphone port/Line In allows you to connect an external microphone, a MiniDisc player, MP3 player, CD player or a tape deck to your notebook. ► Connect the audio cable to the external device. ► Connect the audio cable to the microphone port/Line In of the notebook.
Removing and installing components during servicing Removing and installing components during servicing Only qualified technicians should repair your notebook. Unauthorised opening or incorrect repair may greatly endanger the user (electric shock, fire risk) and will invalidate your warranty. Servicing Components After consulting the Hotline/Service Desk, you may remove and install the components described in this chapter yourself.
Removing and installing components during servicing Preparing to remove components If you are going to remove or change system components, prepare for the removal as follows: Please observe the safety information in chapter "Important notes", Page 12. Remove the power plug from the mains outlet ! ► Switch the device off. The device must not be in energy-saving mode ! ► Close the LCD screen. ► Remove all the cables from the device. ► Turn the device over and place it on a stable, flat and clean surface.
Removing and installing components during servicing Removing a cover 1 2 ► Remove the screw (1). ► Pull off the cover from the notebook in the direction of the arrow (2). Removing memory modules ► Carefully push the two mounting clips outwards (1). The memory module snaps upwards (2). ► Pull the memory module out of its slot in the direction of the arrow (3).
Removing and installing components during servicing Installing a memory module ► Insert the memory module with the contacts and the recess (a) facing the slot (1). ► Carefully push the memory module downwards until you feel it click into place (2). Memory module expansion 2 1 2 a Attaching the cover 2 1 ► ► ► ► ► 84 Place the cover into position, following the direction of the arrow (1). Fasten the cover with the screw (2).
Removing and installing components during servicing Removing and installing the hard disk Removing a cover 1 2 3 ► Remove the screw (1). Keep the screw in a safe place. If you are removing more than one component at the same time, store the screws for the individual components separate from each other. If you install the wrong screws, components may be damaged. ► Slide the cover in direction of the arrow (2). ► Lift the cover off the notebook (3).
Removing and installing components during servicing Removing a hard disk 2 1 ► To release the hard disk from the contacts, pull it in the direction of the arrow (1). ► Remove the hard disk from the hard disk compartment (2).
Removing and installing components during servicing Installing a hard disk 2 1 ► Place the hard disk into the hard disk compartment (1). ► Push the hard disk in the direction of the arrow (2) until the contacts of the hard disk engage.
Removing and installing components during servicing Attaching the cover 3 2 1 ► Place the cover in the correct mounting position (1). ► Slide the cover in the direction of the arrow (2). ► Tighten the screw (3). Finishing component removal After you have removed or changed the system components as you required, please prepare your device for operation again as follows: ► Install the battery again (see "Inserting battery", Page 48).
Settings in BIOS Setup Utility Settings in BIOS Setup Utility BIOS SetupUtility System Setup Configuration,BIOSSetupUtility Hardwareconfiguration settings,BIOSSetupUtility configuration The BIOS Setup Utility allows you to set the system functions and the hardware configuration for the notebook. When it is delivered, the notebook is set to factory default settings. You can change these settings in BIOS Setup Utility. Any changes you make take effect as soon as you save and exit the BIOS Setup Utility.
Settings in BIOS Setup Utility Exiting BIOS Setup Utility BIOS SetupUtility You need to select the desired option in the Exit menu and activate it by pressing the Enter key: Exit Saving Changes - save changes and exit BIOS Setup Utility ► To save the current menu settings and exit the BIOS Setup Utility, select Exit Saving Changes and Yes. The notebook is rebooted and the new settings come into effect.
Troubleshooting and tips Troubleshooting and tips Fault Tips Troubleshooting Follow the safety notes in the "Safety/Regulations" manual when connecting or disconnecting cables. If a fault occurs, try to correct it as described. If you fail to correct the problem, proceed as follows: ► Make a note of the steps and the circumstances that led to the fault. Also make a note of any error messages displayed. ► Switch the notebook off. ► Please contact the Hotline/Service Desk.
Troubleshooting and tips The notebook’s date or time is incorrect Summer Buffer Dateisincorrect Incorrectdate/time Timenotcorrect Time,daylightsavings battery,load time Cause Time and date are incorrect. If the time and date are still set incorrectly after switching on the notebook. Troubleshooting ► With the BIOS-Setup-Utility, you can set the date and time in the main menu. ► Please contact your sales outlet or our Hotline/Service Desk.
Troubleshooting and tips The LCD screen is difficult to read LCDscreen Cause Reflected glare Troubleshooting ► Turn the notebook or alter the tilt of the LCD screen. ► Increase the brightness of the screen. The external monitor remains blank Monitor Cause Monitor is switched off. Power saving has been activated (monitor is blank). Brightness is set to dark. Screen output is set to the notebook’s LCD screen The external monitor’s power cable or data cable is not connected properly.
Troubleshooting and tips The cursor does not correctly follow the pen movements Cause Pen incorrectly calibrated Fault elimination ► Calibrate the pen as shown under Hardware and Sound / Tablet PC Settings in the Control Panel, see "Setting the pen", Page 35 and "Calibrating the pen", Page 36. Pen input not working Cause Incorrect driver installed. Troubleshooting ► If your device is one which can only be operated using the pen, install the driver for the standard model.
Troubleshooting and tips The notebook stops working Energysaving mode Notebook Cause Notebook is in energy saving mode. An application programme has caused the malfunction. The battery is dead. Troubleshooting ► Leave energy saving mode. ► Close the application program or restart the notebook (by restarting the operating system or switching the device off and back on again). ► Charge the battery. or ► Insert a charged battery. or ► Connect the mains adapter to the notebook.
Troubleshooting and tips The battery discharges too quickly Battery: Cause The battery is either too hot or too cold. In this case the battery indicator flashes. Troubleshooting ► Bring the notebook up/down to a normal temperature again. ► If the operating time of the battery life is extremely short, the battery is probably too old. Replace battery if necessary. You may have an application running that ► Use the mains adapter as frequently as consumes a great deal of power due to frequent possible.
Troubleshooting and tips Error message/cause Resolution Extended memory failed at offset: xxxx Failing Bits: ► Check whether the additional memory zzzz zzzz module has been inserted correctly. When testing the extended memory an error has resulted at the address xxxx. Failure Fixed Disk n ► Start the BIOS Setup (Primary Master submenu) and select the correct settings. The settings of the hard disk drive are incorrect. Keyboard controller error ► Switch the notebook off with the ON/OFF switch.
Technical data Technical data Notebook General Processor Main memory (SO DIMM) 4th Generation Intel® Core™ with vPro™ technology (vPro optional, dependent on configuration) Maximum 12 Gbyte DDR3 1 fixed slot with 4 Gbyte (soldered) 1 slot for 2, 4 or 8 Gbyte modules Electrical data Safety regulations complied with Protection class Maximum power draw (when the notebook is switched on and the battery is charged): LCD screen Size Resolution Pixel class Brightness control Technology Digitizer and glass pane
Technical data Tablet buttons Pen Slots Memory card slot ExpressCard slot SIM card slot Ports Monitor port (analogue) HDMI port LAN port Microphone port/Line In Headphones port/Line Out Docking port USB (Universal Serial Bus) Security Lock Ambient conditions Environment class DIN IEC 721 Mechanism class DIN IEC 721 Operating temperature Transport temperature (2K2) Fujitsu 5 buttons + 1 Windows button 1 freely programmable rocker button / eraser 1 x SD Card 1 x ExpressCard/54 1x 15-pin socket 1x Socket, R
Technical data Port Replicator (optional) Electrical data Safety regulations complied with Protection class Ports Monitor port (analogue) CE II 15-pin 25-pin, DVI-D Monitor port (digital) DisplayPort LAN port USB (Universal Serial Bus) Audio Docking port Security Lock Ambient conditions Environment class DIN IEC 721 1x RJ45 4 x USB 3.0 Headphone port 100-pin 1x 7K1 7M2 Mechanism class DIN IEC 721 Operating temperature Transport temperature 5℃ .... 35℃ / 41°F .... 95°F –15°C .... 60°C / 5°F ....
Technical data Mains adapter for use with the notebook and port replicator The following technical data applies to the mains adapter supplied with the notebook and to the port replicator which you can order optionally. Primary Rated voltage Rated frequency Max. rated current Secondary Nominal power Rated voltage Max. rated current 100 V to 240 V (automatic) 50 Hz to 60 Hz (automatic) 0.7 A to 1.2 A 80 W 19 V 4.22 A An additional mains adapter or power cable can be ordered at any time.
Manufacturer’s notes Manufacturer’s notes Disposal and recycling Notes You can find information on this subject on your notebook or on our website ("http://www.fujitsu.com/fts/about/fts/environment-care/"). Declarations of Conformity Declarationofconformity The "Declarations of Conformity" for the device can be found on the Internet at: "http://globalsp.ts.fujitsu.com/sites/certificates/default.aspx".
Manufacturer’s notes Regulatory notices If there is no FCC logo and also no FCC ID on the device then this device is not approved by the Federal Communications Commission (FCC) of the USA. Although it is not explicitly forbidden to travel in the US trading area carrying this device, to avoid trouble at customs clearance, Fujitsu Technology Solutions GmbH recommends not to bring this device into the US trading area.
Manufacturer’s notes This fax modem also complies with fax branding requirements per FCC Part 68. Your telephone company will probably ask you to disconnect this equipment from the telephone network until the problem is corrected and you are sure that the equipment is not malfunctioning. This equipment may not be used on coin-operated telephones provided by your telephone company. Connection to party lines is subject to state tariffs.
Manufacturer’s notes any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line. NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface.
Manufacturer’s notes CAUTION: To reduce the risk of fire, use only 26AWG or larger telecommunications line cord. For Authorized Repair Technicians Only CAUTION: For continued protection against risk of fire, replace only with the same type and rating fuse. WARNING: Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Manufacturer’s notes Exposure from radio frequency devices. The radiated output power of this radio device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation is minimized. When using this device, a certain separation distance between antenna and nearby persons must be maintained to ensure RF exposure compliance. In order to comply with RF exposure limits established in the ANSI C95.
Index Index A A beep sounds every second 92 Acoustic error messages 96 Anti-theft protection 69 Audio devices, connecting 80 Audio ports 80 B Backspace 40 Bass loudspeaker (subwoofer) 58 Battery battery life 46 caring for and maintaining 46 charge level 46, 55 charging 46 self-discharge 46 storage 46 Battery status meter 46 Battery: discharges too quickly 96 BIOS Setup Utility calling 89 exiting 90 operating 89 protecting with password 70 settings 89 Bluetooth Switching off module 60 Switching on module 60
Index G Getting started 15 H Handling data carriers 51 Hardware configuration HDMI port 77 89 I Important notes 12 Incorrect date/time 92 Inserting a data carrier 52 K Keyboard 39 cleaning 14 L Landscape orientation screen 24 LCD screen cleaning 14 difficult to read 93 notes 28 reduce brightness 42 reflected glare 93 remains blank 92 LCD screen is too dark 92 Life, battery 46 Line feed 40 Loudspeaker switch off 42 switch on 42 Loudspeakers 58 M Main memory see Adding memory 82 Mains adapter connecting
Index Password changing 71 entering 70 removing 71 Password protection 70 Password protection: hard disk 72 Peripheral devices connecting 75 disconnecting 75 Port Replicator Ports 63 Portrait orientation screen 24 Ports Port Replicator 63 Power power consumption 55 power-management features Power-on indicator 21 Preparing for operation 16 Printer does not print 95 55 R Radio component: safety notes 12 Rechargeable battery 46 see Battery 46 Regulatory information notebooks with radio device 106 Notebooks
Index USB charging function 79 USB ports 78 User HDD password changing 71 User password entering 70 removing 71 Using the Kensington Lock Cable V VGA connection socket 76 Virtual numeric keypad 41 Volume decrease 42 Fujitsu increase 42 Volume control 58 69 W Webcam 45 Weight Saver Removing 50 Windows key 40 Wireless LAN Switching off module 60 Switching on module 60 Wireless LAN: safety notes 12 111
