C150-E045-03EN M3099EX/GX/EH/GHImageScanner Operator's Guide 00-Cover 1 98.2.
M3099EX/GX/EH/GH ImageScanner Operator's Guide 00-Cover 2 98.2.
M3099EX/GX/EH/GH Image Scanner Operator's Guide 00-Cover 4 98.2.
Edition Date published Revised contents 01 December,1995 First edition 02 April, 1996 M3099EX/GX added 03 May, 1996 Manual modified Specification No. C150-E045-03EN This equiepment has been tested and found to comply with the limits for a Class A digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Please send your comments on this manual or on Fujitsu products to the following addresses: FUJITSU COMPUTER PRODUCTS OF AMERICA,INC. 2904 Orchard Parkway,San Jose. California 95134-2022,U.S.A. TEL:1-408-432-6333 FAX:1-408-432-3908 FUJITSU AUSTRALIA LIMITED 475 Victoria Avenue Chatswood. N.S.W2067,AUSTRALIA TEL:61-2-410-4555 FAX:61-2-411-8603 FUJITSU HONG KONG Limited Room 2521,Sum Hung Kai Centre 30 Harbour Road Wanchal,Hong Kong TEL:852-827-5780 FAX:852-827-4724 TLX:62667 FUJITSU CANADA,INC.
IMPORTANT NOTE TO USERS READ CAREFULLY ALL OF THIS MANUAL BEFORE USING THIS PRODUCT. IF NOT USED CORRECTLY, UNEXPECTED DAMAGES MAY BE CAUSED TO THE USERS OR THE BYSTANDERS.
Preface This manual explains how to use the M3099EX/GX/EH/GH image scanner. This manual contains COMPONENTS, INSTALLATION AND CONNECTION, OPERATING INSTRUCTION,DOCUMENT SPECIFICATION, SPECFICATIONS, ENDORSER and SETUP MODE. Refer to Reference Guide for the information about the routine operation of the M3099EX/GX/EH/GH. Reference Guide contains OPERATING INSTRUCTION, CLEANING, REPLACEMENT OF PARTS, ADJUSTMENT and TROUBLESHOOTING.
Conventions Special information, such as warnings, cautions are indicated as follows: WARNING WARNING indicates that personal injury may result if you do not follow a procedure correctly. CAUTION CAUTION indicates that damage to the scanner may result if you do not follow a procedure correctly. The following symbols are used in this manual. Used for general WARNING and CAUTION. Be careful not to pinch your fingers or hands. iii 01-i`iv 3 98.2.
iv 01-i`iv 4 98.2.
CONTENTS ❑ CHAPTER 1 COMPONENTS Checking the Components ........................................................ 1-1 Units and Assemblies ............................................................... 1-2 Operator Panel(M3099EX/EH) .................................................. 1-4 Operator Panel(M3099GX/GH) ............................................... 1-10 Buzzer Functions ....................................................................
vi 01-i`iv 6 98.2.
CHAPTER CHAPTER 1 COMPONENTS 2 INSTALLATION AND CONNECTIONS CHAPTER CHAPTER 3 OPERATING INSTRUCTION 4 DOCUMENT SPECIFICATION CHAPTER 5 SPECIFICATIONS CHAPTER CHAPTER 6 ENDORSER 7 SETUP MODE GLOSSARY OF TEAMS INDEX COMPONENTS INSTALLATION AND CONNECTIONS OPERATING INSTRUCTION DOCUMENT SPECIFICATION SPECIFICATIONS ENDORSER SETUP MODE GLOSSARY OF TEAMS INDEX vii 01-i`iv 7 98.2.
CHAPTER 1 COMPONENTS After unpacking the scanner,confirm that all the components have been received. This chapter describes the components of the scanner, part names, and operator panel arrangement and their function. Checking the Components Units and Assemblies Operator Panel (M3099EX/EH) Operator Panel (M3099GX/GH) Buzzer Functions 02-Chap. (1) Cover 1 98.2.
1 Cheking the Components These high precision components must be handled with care. Confirm that all the components shown in the following figure have been received. If any component is missing, please contact your sales agent. Terminator (for M3099GX/GH) Scanner Power cable for North America Power cable for Europe or Operator’s Guide (this manual) Consumable kit 1-1 03-Chap. (1) 1 98.2.
Units and Assemblies This section shows the exterior view and assemblies of the scanner. This section also provides names of each part and describes their functions. Types Both M3099EH and M3099GH have two types, 1000 sheets hopper type and 500 sheets hopper type. The 1000 sheets type has an extrusion endorser cover on the top of the unit and the 500 sheets type does not. Therefore it is easy to tell one from another. Be aware that there may be a little difference in handling between them.
Assemblies Sheet guide assembly Lamp socket covers Lamp (Front-side lamp) Roller ASY Pick rollers Guide plate Lamp unit Pad Belt ASY Lamp (Back-side lamp) Belt 1-3 03-Chap. (1) 3 98.2.
Operator Panel(M3099EX/EH) The operator panel is located at the upper right hand side of the scanner. The panel consists of an LCD (24 character x 2 line), LEDs and buttons. Arrangement Operator panel Power Ready Check LCD 24 character x 2 line Duplex Size Density Resolution Manual Front/ Back Landscape Half tone Document Mode 1 Start Stop Mode 2 1-4 03-Chap. (1) 4 98.2.
Button/LED Function Button name Function Start When the Ready lamp is lit in the manual start mode, pressing this button starts a scanning operation. Stop When pressed during scanning: The scanning operation immediately stops and the document under transport is ejected to the stacker. A picked document, if any, is ejected to the stacker. The hopper table is lowered to the bottom. When pressed while waiting for Hopper-timer: The hopper table is lowered to the bottom.
LCD Display The scanner is provided with simplex and duplex reading modes. Simplex reading mode The upper line (line 1) displays the current read mode for simplex reading. The lower line (line 2) displays the mode set and messages when the buttons are pressed. 0 Upper line 1 q 2 3 w e 4 5 r 6 7 8 t 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 y u o i !0 Lower line No.
Duplex reading mode The upper line (line 1) displays the current read mode for front-side reading. The displayed messages are the same as those in the simplex reading mode. The lower line (line 2) displays the current read mode for back-side reading. Only the density, halftone processing, photo/linedrawing mode and image processing option can be specified independently. The other mode is the same as that for front-side reading. 0 Upper line 1 M Lower line No.
Operation status Operation status is indicated by the following message: When the lamps are ready to read, the screen changes to the initial screen of the simplex or duplex reading mode. W a X X r m i _ n g u p N o w X X X X X X I N K E M P T Y ! ! X X X The upper line displays the current read mode for front-side reading. The lower line is blinking and displays the ink empty of print head after the scanning operation.
S F A 4 4 0 0 L . > X X X X X X Abrasion counter The abrasion counter is displayed when initial screen. Stop is pressed in the The abrasion counter disappears when: • The next scanning starts. • The valid switches are pressed. • The error is cleared. The abrasion counter is not displayed if Stop is pressed during blinking. The abrasion counter displays the accumulative number of read document.
Operator Panel(M3099GX/GH) The operator panel is located at the upper right hand side of the scanner. The panel consists of an LCD (24 character x 2 line), LEDs and buttons. Operator panel Power Read Check LCD 24 character x 2 line Manual Mode 1 Start Stop Mode 2 1-10 03-Chap. (1) 10 98.2.
Button/LED Function Button name Function Start This button is used to indicate Start to scanner in maintenance mode or SETUP mode at Off-line. This button is disabled while scanner operates in On-line. Stop This button is used to indicate Stop to scanner in maintenance mode or SETUP mode at Off-Line. This button is used to cancel temporary error while operating at On-line. Manual This button is used to select manual feeding mode.
LCD Display When the Power switch is turned on, the following messages appear on LCD at On-line. W a r m i n g _ u p N o w ! ! ✳ S c a n n e r R e a d y M a n u S c a n n a e l r F e e d R e a d y I N K E M P T Y The lower line is blinking and displays the ink empty of print head after the scanning operation.
S c a n n e r R e a d X X X X X X Abrasion counter The abrasion counter is displayed when Stop is pressed in the Ready screen. The abrasion counter displays the accumulative number of read document. This counter can be reset to zero by following the procedure shown in Chapter 7 (page 7-7). The reading counter or abrasion counter disappears when: • The next start commnad is issued. • The valid switches are pressed. • The error is cleared.
Buzzer Functions The scanner has a buzzer to indicate that an error has occurred. Error Function Equipment error Sounds for 3 seconds. The buzzer turns off when any button is pressed or the power is turned off. Even when a button is pressed, the scanner continues to display the error. Temporary error Sounds during 3 seconds with 0.5 second interval. The buzzer turns off when any button is pressed or power is turned off. Even when a button is pressed, the scanner continues to display the error.
CHAPTER 2 INSTALLATIONANDCONNECTIONS The chapter describes how to install and connect the scanner. Precautions Inspection Cable Connection 04-Chap. (2) Cover 1 98.2.
WARNING Place the machine with no portion of the scanner hangs over the desktop. Never attempt to move or relocate the machine without help. And hold the horizontal plane of the scanner bottom. (Not inclined plane) Precautions ACHTUNG Stellen Sie den Scanner sicher auf eine waagerechte, ebene Flache. Bewegen Sie den Scanner nicht ohne Hilfe. This section describes precautions when installing the scanner. Do not install the scanner in the following places and environments.
Inspection This section describes how to check the labels. Make sure that the input voltage indicated on the temporary label agree with your power source. Label C Temporary label Label A Label D Label B After checking the power voltage rating of the scanner with the temporary label, connect the correct power supply to the scanner. Label A (An example) 2-2 05-Chap. (2) 2 98.2.
Label B (An example) MODEL M3099EH IMAGE SCANNER PART NO. CA02869-B202 AC100-120/200-240V SER. NO. 1 phase DATE 1993-11 FUJITSU LIMITED 2.5/1.25A MADE IN 50/60Hz 65 kgf JAPAN Label C (An example) MODEL NAME HLS-001E PART NO. CA02869-B001 MODEL - 0 1 2 3 4 5 6 7 8 9 REV. - 0 1 2 3 4 5 6 7 8 9 - 0 1 2 3 4 5 6 7 8 9 Label D (An example) Temporary Label (An example) This machine is wired for AC100-120V. To change the Voltage setting, call the service personel.
Cable Connection This section describes how to connect the cables. Connect the cables as follows: Turning the power switch off Press “O” side of the power switch to turn the power off. Power OFF Power switch Power ON Connecting the power cable Connect the power cable to the power inlet of the device and a power outlet. Power inlet Power outlet for North America Power cable for Europe 2-4 05-Chap. (2) 4 98.2.
Connecting the interface cable (M3099EX/EH) Connect the video interface and RS-232C interface cables and secure them with hooks and screws. Connect the other ends to the host machine. [ Back side of the scanner ] Catches Interface cable for RS-232C Screws Interface cable for RS-232C Interface connector for video Interface cable for video To the host machine (M3099GX/GH) Connect the SCSI interface cables and secure them with hooks and connect the other ends to the host machine.
2-6 05-Chap. (2) 6 98.2.
CHAPTER 3 OPERATINGINSTRUCTION This chapter describes how to turn the power on, and also describes button specification and reading mode setting. Refer to Reference Guide about information on loading document and opening/closing the upper transport unit. Turning the Power On Button Specification and Reading Mode Setting (M3099EX/EH) Button Specification (M3099GX/GH) 06-Chap. (3) Cover 1 98.2.
3 Turning the Power On This section describes how to turn the power on. Press “I” side of the power switch. The power goes on and the green Power lamp at the operator panel lights. Operator panel Power OFF Power switch Power ON 3-1 07-Chap. (3) 1 98.2.
Button Specification and Reading Mode Setting (M3099EX/EH) This section describes the button specifications and setup details for each of the simplex (front-side), duplex (front-side) and duplex (back-side) reading modes. When reading mode is set by the command from the host computer, the following button operation is not required. Duplex button This button is used to select simplex or duplex document reading mode.
Simplex (front-side) reading mode setting SF Size A4 400 L. > 400 L. > button Selects a document size. When this button is pressed the lower line is displayed as shown in Screen 3. (M3099EX) Each time this button is pressed, “DLT”, “LT”, “LG”, “A3” or “A4” starts blinking in turn and the size displayed on the upper line changes accordingly. If the direction indicated on the upper line is “ ”, only “LT” or “A4” can be selected.
Density button Selects a density for the read operation. When this button is pressed, the lower line is displayed as shown in Screen 4. Each time this button is pressed, the blinking part in the lower line changes, and the density indicated on the upper line changes according to the blinking part. SF A4 400 Den . : L. > A T ( Au t o ) 2 (Blinking) The lower line is displayed as shown below.
Landscape button (*1) (Portrait) Specifies landscape or portrait mode for reading. When this button is pressed, the lower line is displayed as shown in Screen 6. Each time this button is pressed, the blinking part changes in turn and the_5.5 mode indicated on the upper line changes accordingly. (Landscape) *1; This button is available only for M3099EX. NOTE Landscape mode can be selected only when the document size is LT or A4. (M3099EX) SF A4 400 S i z e : D LT LT LG A3 L.
Half tone button DF Specifies the halftone processing (dither or error diffusion). When this button is pressed, the lower line is displayed as shown in Screen 7. Each time this button is pressed, the blinking part changes in turn, and the halftone indicated on the upper line changes accordingly. H a l f t o n e : OF F H T1 ① With option L. > LP ② ③ (Blinking) Not displayed unless the image processing option is installed.
Document button Selects the type of document. When this button is pressed, the lower line is displayed as shown in Screen 8. Each time this button is pressed, “LINE” or “PHOTO” starts blinking in turn and the document selection indication displayed on the upper line changes accordingly. SF DOC . : A4 400 L . ( L i n e) HT 1 P. > P . ( Ph o t o ) (Blinking) Display Explanation P. (Photo) For light adjustment or when there is a dark background color on the document. L.
Manual button This button is used to set or release the manual mode. Pressing this button displays . The manual mode is set and the hopper goes up. Pressing this button again releases the manual mode and lowers the hopper to the bottom position. M SF A4 400 HT 1 L. > (Manual mode set) button pressed Manual SF A4 400 HT 1 L . > (Manual mode released) 3-8 07-Chap. (3) 8 98.2.
Screen transition 400 SF A4 HT1 L .> Size SF S i z e : SF Density Resolution SF 400 M SF HT1 L . > HT1 400 300 240 400 A4 LG 400 A4 HT 1 400 A4 L. (L i ne ) HT1 L . > HT1 L . > LP HT1 L .> P. ( Pho t o) 400 A4 Manual L . > 200 A4 Ha l f t o n e : OF F DO C . : L . > A T ( Au t o ) 2 A4 LT HT1 A4 A4 Si ze : SF Document LG Res . : 4 00 SF Halftone LT De n . : SF Landscape 400 A4 HT1 L.
Duplex (front-side) reading mode setting DF 400 A4 L. > L .> DB Use the following buttons to set the scanner when it reads the front-side of a document in duplex mode. This description applies to the case when reading the back-side except Density, Halftone and Document buttons. Size button This button is used to select a document size. For details, see the explanation of . (M3099EH) DF A4 400 S i z e : LT L.
Landscape button (Portrait) This button is used to select document reading direction in portrait or landscape mode. For details, see the explanation of . (Landscape) NOTE The landscape mode can be selected only when the document size is LT or A4. (M3099EH) DF A4 Si ze: 400 L. > L T LG A4 (Blinking) (M3099EX) DF A4 400 S i z e : D LT LT L G A3 L.
Document button This button is used to select linedrawing mode or photo mode. For details, see the explanation of . Manual button DF DOC . : 400 L . ( L i n e) P. > P . ( Ph o t o ) (Blinking) M DF This button is used to set or release the manual mode. For details, see the explanation of . A4 A4 4 0 0 HT1 L . > DB L . > (Manual mode set) Manual button pressed DF A4 400 DB HT 1 L . > L .
Screen transition DF A4 400 HT1 L.> DB (Blinking) DF A4 Front/ Back 400 DB button pressed HT1 L .> L.> Size DF A4 S i z e : DF Density Resolution DF DO C . : DF Manual HT1 L . > HT1 400 300 240 400 A4 LT L . > A T ( Au t o ) 2 LG 400 A4 A4 HT 1 400 L. ( L i ne ) HT1 L . > HT1 L . > LP HT1 L .> P. ( Pho t o) 400 A4 L . > 200 A4 Ha l f t o n e : OF F DF Document 400 A4 Si ze : HT1 A4 A4 Res .
Duplex (back-side) reading mode setting Density, Halftone and Document buttons are available when reading the back-side. DF 400 A4 L. > L .> DB Density button This button is used to select a reading density. For details, see the explanation of . Half tone (Blinking) Den . : A T ( Au t o ) 2 DB L. > Not displayed unless the image processing option is installed.
Screen transition DF 400 A4 HT1 DF L.> L.> DB A4 Front/ Back button pressed 400 HT1 L.> L.> DB Front/ Back 400 DF A 4 DB button pressed HT1 L .> L.> Density De n . : DB A T ( Au t o ) 2 L . > (Blinking) Half tone Document Ha l f t o n e : O DB DO C . : DB L. (L i ne ) FF HT 1 LP L . > P. ( Pho t o) L .
Start / Stop button Press each button to start or stop reading. Start button Read operation can be started in either manual or automatic start mode. To start reading in manual start mode, press this button while the ready indicator is lit. (*1) *1: Make sure that the LCD is the initial screen of simplex or duplex reading mode. If not, press Stop button once, then press Start button. Manual start mode: Reading is started by Start button.
Button Specification(M3099GX/GH) This section describes the button specifications. Manual button This button is used to select manual feed mode. Pressing this button switches the setting between Manual mode and ADF mode. When this button is pressed, the scanner enters manual feed mode and the hopper goes up. If the button is pressed again, the scanner exits manual feed mode and the hopper goes down. Start / Stop button These buttons are usedd in Off-line mode.
3-18 07-Chap. (3) 18 98.2.
CHAPTER 4 DOCUMENTSPECIFICATION This capter describes the document size and document guality of the scanner. Document Size Document Quality 08-Chap. (4) Cover 1 98.2.
Document Size The following figure shows document sizes that the scanner can read. A Scanner B Feeding direction Drection Feeding A Maximum B A Minimum B M3099EX/GX 297 (11.7 in) 432 (17 in) 76 (3 in) 63 (2.5 in) M3099EH/GH* 216 (8.5 in) 356 (14 in) 76 (3 in) 63 (2.5 in) (Unit : mm) * The size that M3099EH/GH can read is shown in the table above. However, a document of up to A3 size can be fed. 4-1 09-Chap. (4) 1 98.2.
Document Quality This section describes document types and weights available for the scanner, and precautions. Document type The recommended paper type for document is as follows: NOTE Use the specified paper only. (In rare occasion, double feeding may occur or document damage may occur.) • Fine paper • Plain paper (for example, the paper specified for XEROX4024) • OCR paper When using all other type paper, check that it is successfully fed by ADF before performing a reading operation.
CAUTION Do not feed an important original document to prevent damage to it in rare case. When scanning a translucent document, set the density to light mode. To prevent roller smudging, avoid scanning a document filled out in pencil. Clean the roller as often as possible when scanning many document. Once every 1000 sheets is recommended. The chemical composition of some carbonless papers may react with the roller rubber and damage the rubber. Check the carbonless papers before use.
4-4 09-Chap. (4) 4 98.2.
CHAPTER 5 SPECIFICATIONS This chapter describes the installation specifications, dimensions, consumables, option. Installation Specifications Dimensions Consumables Option 10-Chap. (5) Cover 1 98.2.
Installation Specifications The following table lists the installation specifications of the scanner. Item Specification Width Depth 500 sheet hopper type 610 (24 in) 1000 sheet hopper type 610 (24 in) 680 (26.8 in) 680 (26.8 in) Dimensions (mm) Height 470 (18.5 in) 530 (20.9 in) 55 (121 lb.) for 500 sheet hopper type 65 (143 lb.
11-Chap. (5) 2 530 (1000 sheet hopper type) 470 (500 sheet hopper type) 610 Dimensions 680 (unit: mm) 5-2 98.2.
Consumables The following table lists consumables used for the scanner. Be sure to keep some consumables in stock. Customer is responsible to change these items periodically. The abrasion counter can be used to check the number of scanned documents. (See page 1-9 for M3099EX/EH or page 1-12 for M3099GX/GH.) Name Specification Remark Lamp CA02950-0548 Up to 500 hours or more. Two lamps per scanner. Pick roller CA01023-F242 Up to 300,000 sheets or one year. Requires two per scanner.
Option The following table lists options of the scannera. Name Specification Remark Endorser CA01023-D004 Ink-jet back-side print max. 20 characters (See Chapter 6 ENDORSER.) Contact your Fujitsu sales agent for more information. 5-4 11-Chap. (5) 4 98.2.
CHAPTER 6 ENDORSER This chapter describes the specifications of the endorser and panel operation. Specifications Panel Operation 12-Chap. (6) Cover 1 98.2.
Specifications This section describes the specifications of the endorser. Refer to Reference Guide about information on adjusting the print head position and replacing the print head. The following table lists the endorser specifications. Item Specification Printing method Ink jet printing method Characters Alphabet : A to Z, a to z Number : 0, 1, to 9 Symbol : ! “ # $ % & ‘ ( ) * + - . / : ; < = > ? @ [¥] ^ _ -{|} (blank) Maximum number of characters 20 Character size 2. 9 x 1.5mm (0.11 in x 0.
Panel Operation You can set the following conditions using the operator panel. Other conditions such as print offset or print characters can be set by the host machine. How to set the endorser ON (or OFF) When you use the endorser, you must set the endorser on as follows: 1 While pressing Mode 1 , turn on the power of the scanner. Then the LCD displays SETUP MODE initial screen. 2 Press Mode 1 8 times to display ENDORSER INITIAL screen. Then press Mode 2 .
How to set the initial number The initial number is the number which the scanner starts printing or returns after the reset of the print number. 4 In Screen 3, press Mode 1 until the number you want to display appears. (Ex. The initial number is 5 in Screen 4.) E ND O R S E R VA L U E ✳ ON 5 To store the settings in EEPROM, press Mode 1 until ✳ blinks. Then press Mode 2 to change the LCD display into Screen 5. Press Mode 2 to store the settings. Screen 6 appears for about 3 seconds.
How to select the print number reset method You can choose whether to reset or not the print number when “HOPPER EMPTY” is detected. 8 In Screen 1, press Mode 1 9 times to display ENDORSER RESET METHOD screen. 9 Press to display Screen 8. Press Mode 1 to display “ON” or “OFF”. Each time you press Mode 1 , “ON” and “OFF” appear alternately. Select “ON” to reset the print number when “HOPPER EMPTY” appears and select “OFF” not to reset. The setting is automatically stored in EEPROM.
How to reset the print head life counter You must reset the print head life counter when you replace the print head. 13 In Screen 1, press Mode 1 11 times to display INK RESET screen. MO DE > > < < SE T UP 14 Press Mode 2 to display Screen 13. If you want to reset the counter, press Mode 2 . And you can see Screen 14 for 3 seconds. If you do not want it, press Mode 1 to go Screen 12. Go to 7 to close the job.
6-6 13-Chap. (6) 6 98.2.
CHAPTER 7 SETUPMODE This chapter describes the setup mode of the scanner. Activating the Setup Mode Contents of the Setup Mode 14-Chap. (7) Cover 1 98.2.
Activating the Setup Mode This section describes how to activate the setup mode. 1 Turn the power of the scanner on while pressing Mode 1 . The LCD displays Screen 1. Wa r m i n g - u p 2 After a while, LCD displays SETUP MODE initial screen. (In case of M3099EX/EH, pressing Mode 1 after turning power on displays Screen 2.) 3 Press Mode 1 to select the menu of SETUP MODE. Press Stop to go to the readable status. (In case of M3099GX/GH, Screen 3 indicates the readable status.
Contents of the Setup Mode This section describes the contents of the setup mode. The setup mode can be classified into 17 (M3099EX/EH) or 18 (M3099GX/GH) types. Mode Setup type Contents 1 Setting double feed detection Set in EEPROM whether double feed detection is done or not. 2 Setting IPC-2 pre-set Set in EEPROM the pattern No.of IPC-2 pre-set mode. 3 Reset of abrasion counter Reset the abrasion counter after Belt/Roller are exchanged.
Setting double feed detection When you set the using of double feed detection, you must set as follows: 4 In Screen 2, press Mode 1 once to display DOUBLE FEEDCHECK screen . MO DE > > < < SE T UP 5 Press to display Screen 5. Select “ON” to set the error detection when the double feed occurs. Each time Mode 2 is pressed, “ON” and “OFF” appear alternately. Mode 2 D OU B L E F EE D CHE CK F EE D CHE CK 6 Press Mode 1 to display Screen 6.
8 Press Mode 1 and Mode 2 at the same time to display Screen 4. The settings are stored in EEPROM. When you close, press Stop . Mode Details ON/OFF “OFF” is default setting. 1 “1” is default setting. This mode is used when a batch of documents whose length are same is scanned. When a document with tears and wrinkles is scanned, the scanner may also fail to detect the double-feed. 2 This mode is used when a batch of documents whose length and thickness are same is scanned.
3 If you press the Mode 2 at Sccreen 9, you return to screen 8. The setting is stored to EEPROM. If you press the Mode 2 at screen 10, you go to screen 11. (Screen 12 in case of M3099GH/GX) IPC-2 SET X 4 If you press the Mode 1 at screen 11/12, IPC-2 pre-set mode can be not used. Panel/Host Set Ignore Also the setting is changed to “No” No-Mode 1 Yes-Mode 2 obligatory and stored to EEPROM.
NOTE • For patterns “1” to “5” when the power is turned on Scanner checks that IPC-2 for front/back sides are installed during initialization. If IPC-2 for either the font or back side is not installed, the scanner regards as no setting obligatory and changes the memory of EEPROM. • When IPC-2 pre-set is executed in setup mode Scanner checks that IPC-2 for front/back sides are installed when the scanner enters in IPC-2 pre-set.
Reset of abrasion counter When you reset the abrasion counter, you must set as follows: 1 In Screen 2, press Mode 1 3 times to display PAPER COUNT RESET screen. 2 Press Mode 2 to display Screen 14. You may see current paper count. If you want to reset the count,press Mode 2 . And you can see Screen 15 for 3 seconds. If you do not want it, press Mode 1 to go to Screen13. 3 When you close the setup mode, press Stop .
Setting pre-pick When you set the using of buzzer, you must set as follows: 1 In Screen 2, press Mode 1 5 times to display PREPICK SET screen. 2 Press Mode 2 to display Screen 19. Select “ON” to set the pre-picking when the document is fed. Each time Mode 1 is pressed, “ON” and “OFF” appear alternately. The setting is stored in EEPROM automatically. < < SE T UP MO DE > > P R E P I CK SE T P R E P I CK SE T ON 3 Press Mode 2 to return to Screen 18.
Setting pick speed When you set the pick speed, you must set as follows: 1 In Screen 2, press Mode 1 7 times to display PICK SPEED SET screen. 2 Press Mode 2 to display Screen 23. (The default setting is “FAST”.) If “FAST” is displayed, the pick speed is fast. If “SLOW” is displayed, the pick speed is slow. Each time Mode 1 is pressed, “FAST” and “SLOW” appear alternately. The setting is stored in EEPROM automatically.
When the initial value is “00001”. 00001 00002 (1 Page) (2 Page) 65534 65535 (65534 Page) (65535 Page) NOTE • If “depending on operator panel” is not set by host machine, you can not change the setting. • When “depending on operator panel” is selected, printing starts at the position 20 mm back from the top end of the back side. Setting reset method of endorser Before setting, see page 6-2, “Chapter 6 ENDORSER, Panel Operation”.
Setting RS-232C transfer rate (M3099EX/EH) When you set RS-232C transfer rate, you must set as follows: 1 In Screen 2, press Mode 1 12 times to display RS-232C BAUD screen. MO DE > > < < SE T UP 2 Press Mode 2 to display Screen 25. (The default setting is 4800 bps.) 3 In Screen 25, press Mode 1 until the rate you want to select blinks. RS2 32C BA UD 4 Press Mode 2 to display Screen 24. The settings are stored in EEPROM.
Setting Product-ID (M3099GX/GH) When you set Product-ID, you must set as follows: 1 In Screen 2, press Mode 1 13 times to display PRODUCT-ID SET screen. 2 Press to display Screen 29. (The default setting is “M3099GH” in case of M3099GH and “M3099G”in case of M3099GX.) Mode 2 < < SE T UP MO DE > > P R ODUCT - I D SET 3 In Screen 29, press Mode 1 to select ProductID.
Setting picking time When you set the picking time, you must set as follows: 1 In Screen 2, press Mode 1 14 times (15 times for M3099GX/GH) to display PICK TIMER screen. PI CK 2 Press Mode 2 to display Screen 33. (The default setting is 2 seconds.) 3 In Screen 33, press Mode 1 until the digit you want to change blinks. Then press Mode 2 until the value you want to select appears. (The selectable range is from 0.5 to 99.5 seconds in steps of 0.5 seconds.
Setting hopper time When you set the picking time, you must set as follows: 1 In Screen 2, press Mode 1 16 times (17 times for M3099GX/GH) to display HOPPER TIMER screen. < < SE T UP H O P P E R T I ME R 2 Press Mode 2 to display Screen 37. (The default setting is 7 seconds.) 3 In Screen 37, press Mode 1 until the digit you want to change blinks. Then press Mode 2 until the value you want to select appears. (The selectable range is from 0 to 30 seconds in steps of 1 second.
GLOSSARYOFTERMS A4 size A standard paper size used in Japan and other countries. Paper size is 210 x 297 mm (8.25 x 11.6 inches). Abrasion counter Indicates when belts/rollers should be replaced. The number of read document accumulates until an operator resets the counter. It should be reset when consumables are replaced. ASCII The acronym for American Standard Code for Information Interchange.
Double feed detection A function which detects the status when multiple sheets are fed in the transport unit. dpi Dots per inch. Drop-out color A color which is used to the document but does not appear in the read image. Duplex reading mode Both sides of the document are read in this mode. Endorser The unit for printing characters before or after scanning. These character may be used for collation of the documents and the image data. (See Chapter 6 ENDORSER.
Front-side reading = Front-side scanning Refers to reading the front-side of the document, specifically in Duplex reading mode. Halftone processing Used to reproduce a photograph which includes a shade as an image composed of dots, namely a binary image. Dithering and error diffusion processing are examples of the halftone processing. Heater control The heater is set to ON or OFF to keep the lamp at a constant temperature and stabilize the intensity of the lamp.
Inversion (Reverse-image reading) In reverse-image reading, data is changed from black to white and vice versa. IPC-2 pre-set mode While reading binary images, it is necessary to set the scanner according to the quality of the sheet to be read. In this mode these settings can be performed in advance by corresponding each setting to a pattern number. IPC II Image processing option of this scanner. IRAS Initialization of the hardware.
Noise removal Isolated noise from an image appearing as black spots in white areas and voids in black areas is removed to improve image quality. Operator panel A panel containing the scanner indicators and buttons. The operator panel is used to control scanner operations such as loading document, selecting features, and changing setup options. Outline extraction The boundary between black and white areas is traced and the outline extracted for closed areas.
Pre-picking A setting in which a document to be read next is placed at the front of the reading unit while the previous document is read. Setting the pre-picking makes the process speedier. Print head A cartridge located in the endorser (optional). It contains the ink reservoirs and creates the ink droplets. It is replaceable by operator. Print head life counter = ink counter A counter which accumulates the number of the printed dots.
Serial interface A standard computer interface. Information is transferred between devices over a single wire (although other wires are used for control). With a serial interface, an interface cable greater than 3 meters (10 feet) can be used. This is often necessary in networking environments, where the scanner may be shared. SETUP mode In this mode, users can view or set a variety of function in Off-line. SFI sensor The document detection sensor. It detects the light that transmits the paper.
GL-8 16-GL 8 98.2.
INDEX A A3 1-6 A4 1-6 Abrasion counter 1-9 Activating the Setup Mode 7-1 ADF mode 1-6 Adjusting LCD contrast 7-8 Ambient condition 5-1 Arrangement 1-4 Assemblies 1-3 B Back-side reading mode 1-6 Belt 5-3 Belt ASY 5-3 Button /LED Function 1-5, 1-11 Specification (M3099GX/GH) 3-17 Specification and Reading Mode Setting (M3099 EX/EH) 3-2 Buzzer functions 1-14 C D Cable Connection 2-4 Checking the Components 1-1 Connecting the interface cable 2-5 the power cable 2-4 Consumables 5-3 Consumable kit 1-1 Cont
L Label A 2-2 B 2-3 C 2-3 D 2-3 Lamp 5-3 Landscape 1-6 Landscape button 3-5, 3-11 LCD 1-4, 1-10 LCD Display 1-6, 1-12 LED 1-5, 1-11 Legal 1-6 Letter 1-6 M Manual button 3-8, 3-12, 3-17 mode 1-6 Mode 1 button 3-17 2 button 3-17 O OCR paper 4-2 Operation Status 1-8 Operator’s Guide 1-1 Operator panel 1-4, 1-10, 3-1 Panel (M3099 EX/EH) 1-4, Panel (M3099 GX/GH) 1-10 Option 5-4 P Pad 5-3 Panel Operation 6-2 Paper weight 4-2 Perface ii Photo/linedrawing mode 1-6, 1-7 Pick roller 5-3 Plain paper 4-2 Portrai
S Scanner 1-1 Screen transition 3-9, 3-13, 3-15 Setting buzzer 7-7 double feed detection 7-3 heater control 7-14 hopper time 7-14 initial value of endorser 7-9 IPC-2 pre-set mode 7-4 pick speed 7-9 picking time 7-13 picking start time 7-12 pre-pick 7-8 product-ID 7-12 reset method of endorser 7-10 RS-232C transfer rate 7-11 SCSI-ID 7-11 time-out limit 7-13 Simplex (front-side) reading 1-6 (front-side) reading mode 3-3 reading mode 1-6 Size 1-6 Size button 3-3, 3-10 Specifications 6-1 Stacker 1-2 Start butt
IN-4 17-INDEX 4 98.2.
18-Dec. of Confermity 1 98.2.
18-Dec. of Confermity 2 98.2.
00-Cover 3 98.2.
