2 Technisches Handbuch / Technical Manual Mainboard D1562/D1561 Deutsch / English / Français
Sie haben ... ... technische Fragen oder Probleme? Wenden Sie sich bitte an: • Ihren zuständigen Vertriebspartner • Ihre Verkaufsstelle Aktuelle Informationen und Updates (z. B. BIOS-Update) zu unseren Mainboards finden Sie im Internet: http://www.fujitsu-siemens.com/mainboards Are there ... ... any technical problems or other questions you need clarified? Please contact: • your sales partner • your sales outlet The latest information and updates (e.g.
Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.
Deutsch English Mainboard D1562/D1561 Technisches Handbuch Technical Manual Ausgabe Mai 2003 May 2003 edition Français
Intel, Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt.
Übersicht/Overview Mainboard D1562/61 1= 2= 3= 4= Interne Anschlüsse und Steckplätze / Internal connectors and slots 22 23 1 Channel B Channel A 2 3 4 21 5 6 slot 4 slot 2 slot 3 slot 1 AGP / GPA 7 PCI 1 8 9 PCI 2 20 10 PCI 3 19 18 17 11 16 15 14 13 12 5= 6= 7= 8= 9= 10 = 11 = 12 = 13 = 14 = 15 = 16 = 17 = 18 = 19 = 20 = 21 = 22 = 23 = Diskettenlaufwerk / Floppy disk drive Power On LED II Bedienfeld / Front panel Stromversorgungsüberwachung / Power supply control IDE-Laufwerke 3/4 / I
Contents Mainboard D1562/D1561..................................................................................................................1 Notational conventions ..............................................................................................................1 Important notes..................................................................................................................................2 Information about boards ...........................................................
Mainboard D1562/D1561 Your mainboard is available in different configuration levels. Depending on the configuration chosen, some of the hardware components described may not be available on your mainboard. Additional information Information on the BIOS Setup and additional descriptions of the drivers are contained: • • • in the readme files on your hard disk on the driver floppy disks included on the CD "Drivers & Utilities Collection" or "Drivers & Utilities" or "ServerStart".
Important notes Important notes With the mainboard installed you must open the system to access the mainboard. How to dismantle and reassemble the system is described in the operating manual accompanying the system. Connecting cables for peripherals must be adequately shielded to avoid interference. ! Observe the safety notes in the operating manual of your system. Incorrect replacement of the lithium battery may lead to a risk of explosion.
List of features List of features Onboard features Chipset Board size VGA Audio / 6-channel / S/PDIF 5.1 D1562-A D1561-A Intel 865 G Intel 865 G µATX µATX ü ü ü/-/ü ü/-/ü -/ü -/ü ü/ü/-/ü ü/-/-/- RAID - - FireWireTM - - HI-SPEED USB 2.0 ü ü Buzzer / int.
List of features Internal ports (continued) D1562-A D1561-A SMBus Connector* (Case Temperature) 1 - Intrusion Connector* (Case Open) 1 - 1/1/- 1/1/- D1562-A D1561-A Power Connectors ATX / ATX12V / AGP PRO External ports VGA Audio Line in / Line out / Mic In Game/MIDI LAN (RJ-45) PS/2 mouse/keyboard 1 1 1/1/1 1/1/1 - - 1 1 1/1 1/1 1394 port (FireWireTM) - - USB Ports (2.
List of features Silent Mode and Harddisk Password are activated in the BIOS Setup. Additional information is contained in the "BIOS Setup" manual. Logo Boot A customer-specific logo can be displayed during system booting. The logo is loaded using the LogoFlash tool. The logo can have a size of 640 x 480 pixels with 16 colours. The tool is provided on the CD "Drivers & Utilities" or "Drivers & Utilities enhanced" or is available on the Internet at http://www.fujitsu-siemens.com/mainboards.
Brief instructions on installing mainboard If you have purchased a separate mainboard, you can install the mainboard in your system in accordance with the following brief instructions. The activities described here assume a basic knowledge of PCs and cannot be carried out by a layperson. If you are not sure whether you have the necessary specialised knowledge, then leave this work to an expert. The illustrations of the system show examples of possible cases.
Brief instructions on installing mainboard Ê Should no suitable connection field be provided in the case, then you must install the connection field (1) provided. Ensure the plate is aligned properly so that the connections are suitable for the mainboard later. Ê Set the mainboard on the edge on which the connection field is located (2) and then insert the board in the case (3). Make sure that spacers in the housing are only mounted at points at which there are mounting holes in the mainboard.
Interfaces and connectors The positions of the interfaces and connectors are shown on page "Cover". The components and connectors marked are not necessarily present on the mainboard. External ports The positions of the external ports are shown on page "Cover".
Internal ports and connectors Graphics port - Supported screen resolutions Depending on the operating system used, the screen resolutions in the following table refer to the mainboard screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the operating manual or technical manual supplied with the controller.
Pin assignment of internal ports Pin assignment of internal ports The pin assignment of some internal connections is shown in English in the following. i Some of the following connectors may be optional! Power On/Off Front panel Watch the poling of the LEDs. The positive pole of the connection cables is often indicated with a coloured wire.
Pin assignment of internal ports Pin Signal Pin Signal 1 3 5 7 GND Transmit data negative Receive data negative GND 2 4 6 8 Transmit data positive GND Receive data positive Key 2 ATA interface 1 Pin Signal Pin Signal 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Reset drive (low asserted) Data 7 (high asserted) Data 6 (high asserted) Data 5 (high asserted) Data 4 (high asserted) Data 3 (high asserted) Data 2 (high asserted) Data 1 (high asserted) Data 0 (high asserted) GND DRQ (high
Pin assignment of internal ports Audio S/PDIF 1 Pin Signal 1 2 3 VCC SPDIF out GND 1 CD audio input Pin Signal 1 2 3 4 Left CD audio input CD GND CD GND Right CD audio input AUX audio in 1 Pin Signal 1 2 3 4 Left AUX audio input Analogue GND Analogue GND Right AUX audio input 12 - English A26361-D1562-Z120-2-6319
Pin assignment of internal ports 1 Stromversorgungsüberwachung / Power supply control Pin Signal 1 2 3 4 5 6 7 8 AC Outlet (high asserted) PS FAN Control (low asserted) PS FAN full on (low asserted) PS FAN Sense SMB CLK SMB DATA VCC EEPROM (+3.
Pin assignment of internal ports USB E/F - dual channel 1 2 11 12 (internal or external via special wire) Pin Signal Pin Signal 1 3 5 7 9 11 Key VCC C Data negative C Data positive C GND Key 2 4 6 8 10 12 Chipcard reader on VCC D Data negative D Data positive D GND not connected USB G/H - dual channel (internal or external via special cable) 1 2 11 12 Pin Signal Pin Signal 1 Key 2 Chipcard reader on 3 VCC C 4 VCC D 5 Data negative C 6 Data negative D 7 Data positive C 8
Pin assignment of internal ports Serial port 2 1 2 Pin Signal Pin Signal 1 3 5 7 9 DCD 2 SIN 2 SOUT 2 DTR 2 GND 2 4 6 8 DSR 2 RTS2 CTS 2 RI 2 1 Fan 1 (processor fan - only for 3 pin fans) Pin Signal 1 2 GND Controlled FAN voltage (0V, +6V, ... +12V, max. 1A) or fix Fan voltage (+12 V, max. 1 A) Fan sense 3 1 Fan 2 Pin Signal 1 2 GND Controlled FAN voltage (0V, +6V, ... +12V, max. 1A) or fix Fan voltage (+12 V, max.
Pin assignment of internal ports 1 Power supply ATX 11 Pin Signal Pin Signal 1 2 3 4 5 6 7 8 9 10 +3.3V(P3V3P) +3.3V(P3V3P) GND +5V (VCC) GND +5V (VCC) GND Powergood (high asserted) +5V Auxiliary (VCC Aux) +12V (P12VP) 11 12 13 14 15 16 17 18 19 20 +3.
Pin assignment of internal ports Settings with switches and jumpers Your mainboard is equipped with switches or jumpers. The positions of the switches or jumpers are shown on page "Cover".
Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter! Even when you have switched off the device, parts (e.g. memory modules, AGP and PCI extension boards) are still supplied with power. Replacing processor Technical data • • Pentium 4 with 400/533/800 MHz Processor System Bus in the mPGA478 design.
Replacing processor Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. Otherwise you must apply a very thin layer of heat conducting paste. Heat conducting pads can only be used once. If you remove the heat sink, you must clean it and apply new heat conducting paste before you remount it.
Upgrading main memory Upgrading main memory Technical data Technology: DDR 266, DDR 333 or DDR 400 unbuffered DIMM modules 184-Pin; 2.5 V; 64 Bit, no ECC Size: 128 Mbytes up to 4 Gbyte DDR 266 SDRAM 128 Mbytes up to Gbyte DDR 333 SDRAM 128 Mbytes up to Gbyte DDR 400 SDRAM Granularity: 128, 256, 512 or 1024 Mbyte for one socket A current list of the memory modules recommended for this mainboard is available on the Internet at: www.fujitsu-siemens.com/mainboards.
Upgrading main memory 533 333 333 266 400 266 266 266 Installing a memory module 2 2 Ê Ê Ê Push the holders on each side of the memory slot outwards. Insert the memory module into the location (1). At the same time flip the lateral holders upwards until the memory module snaps in place (2). Removing a memory module 1 1 Ê Ê Push the clips on the right and left of the memory slot outward (1). Pull the memory module out of the memory slot (2).
Upgrading AGP screen controllers Upgrading AGP screen controllers Technical data: The AGP slot supports the modes 4x/8x with 32 bits and 66 MHz. Only 1.5 V AGP graphics cards are supported. i Some older 3.3 V AGP graphics cards are coded like 1.5 V AGP graphics cards. The installation of such 3.3 V AGP graphics cards can cause serious damage to the mainboard and the AGP graphics cards. Adding PCI cards Technical data: 32 bit / 33 MHz PCI slots 5 V and 3.3 V supply voltage 3.
Adding PCI cards Controller or slot INT Mechanical slot Onboard controller 1 AC97 3 4 1 2 3 PCI slot 2nd 3rd 4th 1 (A) X - - X - - - - - A - - - 2 (B) - - - - - X X X - B - - - 3 (C) - - X - - - - - - - D C A 4 (D) - X - - - - - - - - C D B 5 (E) - - - - - - - - X - - - - 6 (F) - - - - - - - - - - B A C 7 (G) - - - - - - - - - - A B D 8 (H) - - - - X - - - - - - - - LAN Modem Audio A
Adding PCI cards Replacing the lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced.
BIOS update BIOS update When should a BIOS update be carried out? Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. In addition, new BIOS functions can also be integrated. A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software. Where can I obtain BIOS updates? The BIOS updates are available on the Internet at www.fujitsu-siemens.de/mainboards.
Microcode Update Ê Ê Ê Ê Ê Ê Set the switch for "Restore system BIOS" to OFF. Close the casing as described in the operating manual. Remove the floppy disk from the drive. Start the PC and invoke BIOS Setup. Select the menu item Reset Configuration in the menu Advanced and change the setting to Yes. Save the change and terminate BIOS Setup. The BIOS recovery has now been completed. The system restarts.
Drivers Microcode update under DOS with bootable microcode update floppy disk - brief description Ê Ê Ê Ê Ê Ê Download the update file from out website to your PC. Insert an empty floppy disk (1.44 MB). Run the update file under DOS (e.g. 1495101.EXE). A bootable update floppy disk is created. Leave the floppy disk in the drive. Restart the PC. Follow the instructions on screen. To determine whether the latest microcode update has been loaded, the so-called Patch-ID of the processor can be read out.
Annex Electrical Properties Loadability for connections and fuses i Make sure that the connected devices do not overload the connections. Fuse no.
APM and ACPI system status, energy-saving modes APM and ACPI system status, energy-saving modes System status Normal operation Simple energysaving mode ACPI Status )1 G0 G1 Maximum energysaving mode )4 APM Status Power LED I )2 Power LED II )3 Sleep LED Power consum ption Wake-up time S0 On On/Off On Off Normal S1 Standby Off/On flashin g On Almost like normal Almost immediate ly S3 Off/On flashin g RAM, wake-up compon ents ca. 5s S4 Off/Off Off RAM, wake-up components ca.
Mainboard Revision and BIOS Version Mainboard Revision and BIOS Version The compatibility, e.g. with new processors, can be independent of the BIOS version or the revision status of the mainboard used. The CPU and BIOS compatibility lists are available on the Internet at www.fujitsu-siemens.de/mainboards. Mainboard Revision The revision status of the mainboard exactly identifies which mainboard you have.
Error messages This chapter contains error messages generated by the mainboard. Available CPUs do not support the same bus frequency - System halted! Memory type mixing detected Non Fujitsu Siemens Memory Module detected - Warranty void There are more than 32 32 RDRAM devices in the system Check whether the system configuration has changed. If necessary, correct the settings.
Error messages DMA test failed EISA CMOS not writable Extended RAM Failed at offset: nnnn Extended RAM Failed at address line: nnnn Failing Bits: nnnn Fail-Safe Timer NMI failed Multiple-bit ECC error occurred Memory decreased in size Memory size found by POST differed from EISA CMOS Single-bit ECC error occurred Software NMI failed System memory exceeds the CPU’s caching limit System RAM Failed at offset: nnnn Shadow RAM Failed at offset: nnnn Switch the device off and on again.
Error messages Missing or invalid NVRAM token Switch the device off and on again. If the message is still displayed, please contact your sales outlet or customer service centre. Monitor type does not match CMOS - RUN SETUP Correct the entry for the monitor type in the Main menu of the BIOS Setup. On Board PCI VGA not configured for Bus Master In the BIOS Setup, in the Advanced menu, submenu PCI Configuration, set the Shared PCI Master Assignment entry to VGA.
Error messages System battery is dead - Replace and run SETUP Replace the lithium battery on the mainboard and redo the settings in the BIOS Setup. System Cache Error - Cache disabled Switch the device off and on again. If the message is still displayed, please contact your sales outlet or customer service centre. System CMOS checksum bad - - Default configuration used Call the BIOS Setup and correct the previously made entries or set the default entries.
Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described mainboard.
