P3PC-1492-04ENC2 FUJITSU TWAIN 32 Scanner Driver Scanner Utility for Microsoft® Windows® Version 9.20 User's Guide For Use with Microsoft® Windows® 98, Windows® Me, Windows® 2000, Windows® XP and Windows ServerTM 2003 ® ®, (* For Windows 95 and Windows NT 4.0, refer to Version 8.20 User’s Guide.
Introduction ® ® Thank you for purchasing the "Scanner Utility for Microsoft Windows V9.20". This software contains a TWAIN-compliant image scanner driver (simply called "driver" in this guide) and utilities. This guide provides a description summary of the driver, as well as a description of the installation method and procedures for appropriate use. Please read this guide before starting to use the software. In addition, read the README.
Trademarks Microsoft, Windows, Windows NT and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other countries. Intel, MMX, Pentium are registered trademarks of Intel Corporation. Adobe, Acrobat are the trademarks or registered trademarks of Adobe Systems Incorporated. Adaptec is a registered trademark of Adaptec Inc. EZ-SCSI is a trademark of Adaptec Inc. Other product names are the trademarks or registered trademarks of the respective companies.
Organization This manual explains how to install and use this driver, and how to use the TWAIN scanning utility. • Installation This section explains the procedure for installing the environments in which this driver may operate. • Using the Driver This section explains how to use the driver.
Contents 1. Outline .............................................................................................. 1 1.1 Characteristics of this Driver ...........................................................................1 1.2 Operating Environment...................................................................................1 1.3 Explanatory Notes ..........................................................................................2 1.4 Explanation of terms .................................
4.7.6 Filter.....................................................................................................................52 4.7.7 Compression........................................................................................................56 4.8 Setting Advance Options ..............................................................................57 4.8.1 Gray .....................................................................................................................58 4.8.
.2 Device Trouble Related to Operation..........................................................112 7.3 Device Trouble Related to Installation ........................................................113 8. Appendix ...................................................................................... 114 8.1 Relevant Image Scanner Specification .......................................................114 8.2 Maintenance Service ................................................................................
1. Outline 1.1 Characteristics of this Driver • This driver complies with TWAIN regulations V1.9 (the latest version as of June 2006), which are global standards for image scanners. The driver can be used in all TWAINcompliant applications. • This driver also supports an image scanner that has the "double-sided scan" function. If the application supports continuous scan, a double-sided document can be scanned. 1.
® − Windows XP − Windows Server ® TM 2003 • USB port • RAM: 32 MB or more (a minimum of 64 MB is recommended) • Available hard disk space: 10 MB or more (excluding the area for storing images) • CD-ROM drive (required for installation) • Mouse (recommended) 1.3 Explanatory Notes The descriptions in this manual are prepared based on the following rules: ◊ Menus and buttons The menus and buttons used in the program description are enclosed in [].
◊ Notes on operation procedures If some menus need to be operated in a certain order, the procedural order is described as follows: [A] - [B] - [C] In accordance with this description, operation [A] is executed first, followed by [B] and [C] in that order. ◊ Figures ® ® Figures and screen operations in this guide refer to Microsoft Windows 2000. They are also followed when using other operating systems. Note that the expressions may vary with the type of scanner connected. 1.
2. TWAIN 2.1 TWAIN TWAIN is the specification that defines the standard software protocol and application programming interface (API) for data exchange between a software application program and an image input device such as the image scanner. [TWAIN development background] In the past, development of a new scanner inevitably required the development of a compatible driver and a sample (demonstration) program exclusively designed for the new scanner.
2.2 TWAIN Application TWAIN mainly applies to the following three software components: Application software Source manager Source The components are related to each other as shown below. Application software (photo retouching software, etc) Source manager (TWAIN.DLL/TWAIN_32.DLL, etc) Source (Image scanner control of the driver, etc) Image scanner, etc.
3. Installation 3.1 Preparation 1. Make sure that the operating system (OS) is installed correctly. 2. In case of the SCSI connection, confirm that the SCSI adapter is connected to your PC and operating correctly. In case of the USB connection, confirm that the USB port is installed in your PC. 3. Confirm that the hard disk that is the installation destination has enough free space. 4. If old version FUJITSU TWAIN 32 Driver has already been installed on your PC, uninstall it before installation.
3.2 Installing the Scanner Driver The Windows® XP screen samples are shown below. The screen and operations will differ slightly depending on the OS that is being used. 1. Turn on the scanner. ® 2. Turn on your PC and Log on to Windows . When using Windows® 2000, Windows® XP or Windows ServerTM 2003, log on as an administrator. The scanner may be detected automatically, and the "Found New Hardware Wizard" (or “Add New Hardware Wizard”) window is displayed.
In case of Windows® 2000 In case of Windows® XP, Windows ServerTM 2003 3. Insert the Setup CD-ROM into the CD-ROM drive. is displayed. This Dialog is not displayed automatically when "Auto play" setting of your PC is off. In this case, please run “Install.exe” in this CD-ROM directly using “Explore” or “My computer”.
4. Click [INSTALL PRODUCTS]. (* Depending on the scanner model, the different screen may appear.) 5. Click [TWAIN Driver] (* Depending on the scanner model, the different screen may appear.) Depending on the scanner model, the screen which confirms whether “Error Recovery Guide” is installed or not is displayed. In this case, click [OK] button, and install Error Recovery Guide.
6. Select the language you use in [Choose Setup Language], then click [OK] button. 7. Click [Next >] button. 8. Read the information of README File, and then click [Next >] button.
9. Read the License Agreement carefully, and then click [Yes] button if you agree. If you click [No] button, the installation is stopped. 10. Confirm Destination Folder, and then click [Next >] button. Usually, it is not necessary to change Destination Folder. 11. Confirm Components you install, and then click [Next >] button. Usually, it is not necessary to change the selection of Components.
12. Confirm Program Folder, and then click [Next >] button. Usually, it is not necessary to change the Program Folder’s name. 13. Click [Next >] button, and copying files is started. 14. Select “Yes, I want to restart my computer now”, and then click [Finish] button. 15. After the restart, the scanner is detected. Depending on the OS, the following operations may be required.
In case of Windows® 98 ® There is a request to insert a disc. When this happens, insert the Windows 98 CD-ROM in your CD-ROM drive. In case of Windows® 2000 [Digital Signature not Found] is displayed, click [Yes] button. In case of Windows® XP, Windows ServerTM 2003 1) [Found New Hardware Wizard] is displayed, click [Next >] button. 2) If [Hardware Installation] is displayed, click [Continue Anyway] button. 3) Click [Finish] button when the installation is finished.
Now, the installation of scanner driver is completed.
3.3 Uninstall The uninstall process removes the software and returns the hard disk to its pre-installation state. When you want to remove this scanner driver program from your PC, uninstall by the following procedures. ® 1. Turn on your PC and Log on to Windows . When using Windows® 2000, Windows® XP or Windows ServerTM 2003, log on as an administrator. 2. Close all of the applications on Windows ® 3. Select [Control Panel] from [Start] menu. The [Control Panel] is displayed. 4.
4. Using the Driver 4.1 Selecting the Driver To use this driver from the TWAIN application, select "FUJITSU " from the TWAIN data source (driver) selection screen. For general application, the data source selection screen is displayed by selecting the [Select Scanner] or [Acquire ...] menu. Refer to the instruction manual for the application used for details. 4.
4.2.1 Linkage to Image Processing Software Option When the “Enable Software IPC” checkbox is marked after installation of “Image Processing Software Option” (sold separately or included as a standard function)*, there appears setting items of Image Processing Software Option in a part of the Setting Window for TWAIN Driver. (*: Depending on the scanner, the option is installed together with the scanner driver. See "Relevant Image Scanner Specification" in the Appendix.) Mark this checkbox.
4.3 Displaying Driver Information ♦ Image scanner name The model name, option port name, and capacity of internal scanner memory (in units of megabytes) of the connected image scanner are displayed. If no image scanner is connected, this field is blank. The type of IPC option board is displayed if an image-processing option board is installed in the scanner. IPC-3/3D may not be detected normally, as it is affected by the version number of the machine type and device. In this case, "IPC2" is displayed.
4.4 Setting Information on Image Scanning ♦ Current side When a scanner that allows duplex scanning is used, specifies the page which sets the image scanning information. To scan using the same settings as those for "Front side" and "Back side," clear the checks in the "Individual Setting" checkbox on the "Front" and "Back" tabs. A single "Duplex" tab will be displayed at the left so that the same image scanning information can be set for "Front side" and "Back side.
- Output mode Multi Image Output One scan outputs both a Color/Grayscale and a Binary B/W image. Auto color Detection Outputs either a Color/Grayscale or a Binary B/W image depending on whether the document is color or black and white. - Order (for Multi Image Output) Specify the output order of images when scanning in Multi Image Output mode.
When you use the "Multi Image" function (Multi Image Output and Auto Color Detection) together with the "Filter" function (Page Edge Filter and Digital Endser), the "Filter" setting is common to both Multi Image Output and Auto Color Detection. You cannot configure different "Filter" settings for each. ♦ Resolution Specifies the number of pixels (dots) per inch. Select a predefined resolution or [Custom] from the list. [Customize] enables detailed settings by a pixel unit.
♦ Paper Size Specifies a document size for scanning. Select a standard size or [Custom] size (can be registered up to three) from the list. Window for customizing the paper size will appear when you click on […] button besides the list. On this window, you can change the order of the paper size in the list. [Custom] button : Used for configuration of a custom size. [Up] button : Used for shifting the order of the selected document size upward.
Specifies the start position, width and length for the image scan. The maximum allowable size is the paper size selected previously. In addition, the minimum size is 1.000 inch, 26 millimeters, or pixels (number of dots per inch) according to the unit that has been set.
Long page (Front Side) Scans a document longer than the paper size which can be specified by [Paper Size]. In this case, only the front sides of documents are scanned. When this option is selected, the "Paper Size Setting" dialog box opens. Specify the size of the document to be scanned. * While the "Long page" is specified, the preview window cannot be displayed and the scanning area cannot be specified.
Some versions of the scanner do not support this scanning mode. For details contact the retail store where the device was purchased. 4bit Gray scale Scans data using 16-level monochrome gray scale. Data size is smaller than "Gray scale" selected. Some versions of the scanner do not support this scanning mode. For details contact the retail store where the device was purchased. Automatic separation Scans data distinguishing line drawing from photograph image.
SDTC, DTC mode To enable the auto binary function of the image scanner, specify this option. If this option is selected, the "Threshold" setting will be disabled. In addition, auto binary has two modes: " SDTC Mode" and "DTC Mode". These modes can be set using the "Advance" dialog box. "DTC Mode", however, is limited to the image processing options. Therefore, only scanner models that have image processing options support "DTC Mode". See "Relevant Image Scanner Specification" in the Appendix.
Some scanner models do not support this function. See "Relevant Image Scanner Specification" in Appendix.
♦ Scanning Parameters For fine scan adjustments. Since there is no fixed set of values, set by trial and error. ◊ Brightness: Sets the brightness of the overall image. Specify the brightness with a number in the range of 1 (bright) to 255 (dark). To darken the overall image, increase the value of the setting. To brighten the overall image, decrease the value. This parameter can be set if "Halftone" or "Automatic Separation" is selected for "Image Mode.
4.5 Specifying Driver Operation ♦ [Preview] Scans in a preliminary image based on set values, and displays the image in the preview window. Before actual scanning, the preview function can be used to display the entire document for specifying the desired scan area. Some models do not support this function. See "Relevant Image Scanner Specification". ♦ [Scan] Scans the specified scan range based on set values.
♦ [Help] Displays online help. When the [F1] key is pressed, help information regarding the item on which the cursor is placed is displayed. Note Depending on the application used help information may not be displayable with the [F1] key. This is because the driver operation is controlled through the application and the [F1] key may be used differently in each application program. Help information can be displayed by pressing the [F1] key while holding down the [Ctrl] or [Shift] key.
4.6 Setting "Scanning Area" Specify the scanning area in the preview window as follows: Setting: 1. Press the left mouse button to specify the origin (top left corner) of the scanning area. (The cursor appears as a "+".) 2. Drag the mouse to show the outline of the scanning area. (As the cursor moves, a range frame is shown.) 3. Release the left mouse button again to set the range (bottom right corner) of the scanning area. Movement: 1. Move the cursor into the range frame. (The cursor appears as a hand.
4.7 Setting Options The "option dialog" is used to set device-specific functions and the items that differ depending on whether the scanner used supports them. The option specification is divided into "Rotation", "Job/Cache", "Generic", "Imprinter (Endorser)" , "Start Up", “Filter” and “Compression”. The supported options depend on the scanner. See "Relevant Image Scanner Specification" in the Appendix. ( is displayed for options that cannot be used.) The option dialog in this driver is explained below.
The options are described below: 4.7.1 Rotation Figure Option dialog (Rotation) ♦ Flip Side Rotation Specifies the binding of the document when both sides are scanned using ADF. Book Outputs the scanned image for both sides as is. Select this option to scan documents bound on the left or right side Fanfold Outputs the scanned image of the backside rotated 180 degrees. Select this option to scan documents bound on the top or bottom (Front side and backside are printed conversely.
♦ Rotation Degree Outputs the scanned image rotated to the right or left 90 degrees. 0.0 degree Outputs the scanned image as is. 90.0 degree Outputs the scanned image rotated 90 degrees to the right (clockwise). -90.0 degree Outputs the scanned image rotated 90 degrees to the left (counterclockwise). 180.0 degree Outputs the scanned image rotated 180 degrees (top and bottom reversed). ♦ Automatic Size and Skew detection Disable This option outputs the image as it was scanned.
selected (Double Letter) paper size range is used for scanning, the output will adjust to the page size detected. (However, in case of fi-4860C/fi-4990C/fi-5650C/fi-5750C, this function is not dependent on the setting of [Paper size] because these scanners always scan documents as the maximum paper size and detect the paper size from the scanned data.) This function does not work properly for some applications.
This option may not be supported for some scanners. See "Relevant Image Scanner Specification" in the Appendix.
4.7.2 Job/Cache Figure Option dialog (Job/Cache) ♦ Caching Specifies whether to pre-read (cache) when a document is scanned. This option enables faster scanning. If processing of the application being used slows down and scanning stops, this option can be used to prevent degradation of the scanning speed. (The effect, however, depends on the environment being used.) None Caching is not performed.
Use Both Memory Pre-reads using memory of both Scanner and PC (displayed only if supported by the scanner). ♦ Batch Detection The application can detect documents on a specific type of form (special paper). The application must support this function. None No detection. Scanning is done without change. Include and Continue After the special paper is detected, scanning continues. The data on the special paper is also valid. Include and Stop After the special paper is detected, scanning stops.
Check length The length of the transmitted document is checked by the sensor in the device. A multifeed is detected by detecting changes in the length when more than one document is sent. Check thickness and length The thickness and length of the transmitted document are checked. Check overlapping The overlapping of the transmitted document is checked by the sensor in the device. A multifeed is detected by overlapping when more than one document is sent.
♦ Check Over-skew The skew of the transmitted document is supervised during the ADF scanning. When an over-skew is detected, the scanner is stopped and an error message is displayed. * The image data of the skewed document is deleted. * This functions, only when “Multifeed Detection” is enabled. * Skew Detection is a function used for detecting over-skew to stop feeding skewed documents. If sheets of paper are stapled together, miss-detection may occur.
* − If a blank page is scanned, increase the value set. − If scanning is skipped up to the required document, decrease the value set. When “Black Background” is selected in [Automatic Size and Skew detection], the Blank page skip may not operate properly. When Scanned image has many background noises, the Blank page skip may not operate properly.
4.7.3 Generic Figure Option dialog (Generic) ♦ Unit/Scaling This option selects the unit for the scanning area and preview window. One inch is calculated as 25.4 millimeters. When inches are converted to millimeters, values are rounded off. Note. The TWAIN specifications require that the data width be arranged in units of 32 bits. As a result, a difference of up to 31 dots can be included, depending on the value set.
4.7.4 Imprinter (Endorser) Figure Option dialog (Imprinter) ♦ Enable Imprinter (Endorser) Specifies enabling or disabling the imprinter function of the device. When the option is selected, the scanned documents are imprinted according to the instructions below. This applies only to the imprinter option. Therefore, the function is supported only with the scanner which supports imprinter option(s). See "Relevant Image Scanner Specification" described in the Appendix. Disable Imprinting is not performed.
Post-Imprinter (Printing after scanning, and on the back side of documents) Prints on documents using the imprinter installed in rear part of the scanner. In this case, it prints on the back side of documents after scanning. Therefore, the printing is not included in a scanning result. * [Pre-Imprinter] and [Post-Imprinter] cannot be used at the same time. ♦ Y Offset (Printing) Specifies Y Offset from the edge of the original for the placement of printing.
♦ Initial Value (Counter) Designates the initial count when the Imprinter String is set, including a counter value. See the "Relevant Image Scanner Specification" described in the Appendix since the programmable values range depends on the device. ♦ Counter Step (Counter) Designates the counter increment of the set counter values. In other words, this value is added to or subtracted from the counter each time one original is scanned. An increment of 0, 1, or 2 may be specified.
♦ %MM: The month is printed in two digits; for example, 01 for January and 12 for December. %M: The month is printed using one or two digits; for example, 1 for January and 12 for December. %DD: The day is printed using two digits; for example, 03 for the 3rd day of the month and 26 for the 26th day of the month. %D: The day is printed using one or two digits; for example, 3 for the 3rd day of the month and 26 for the 26th day of the month.
4.7.5 Start Up Set up the Power Mode, Low-Speed Feeding and Scanner Operation Panel. In some scanner models, displayed dialog box or setup item may be different or even [Startup] dialog box may not be displayed.
In case of model fi-5750C In case of model fi-5650C Figure Option dialog (Start Up) 48
In case of model fi-5900C Figure Option dialog (Start Up) ♦ Power Mode Quick Start Mode This mode keeps the lamp on regardless the scanner’s operating condition, which saves times for lamp to become steady. Low Power Mode To save the power consumption, this mode turns the lamp off, if the scanner is not operated for 14 minutes. ♦ Enable Low Speed Feeding This is to specify to obtain a high quality image.
When checking this check box, scanning speed becomes faster, but image quality is slightly deteriorated. Check this check box, when giving priority to scanning speed over image quality. ♦ Scanner Operation Panel − Enable Scanner Panel This is to specify whether the operator panel is enabled or not. If this is checked, button operation on the operator panel becomes effective. (Note that the operator panel is enabled only during the driver is activating.
− Enable [Send to] button Specifies whether the preview is started by pressing the [Send to] button on the device. − Enable FB Scanning Start Specifies whether Scanning is started by closing the Flat bed cover. When setting the document on the Flat bed and closing the Flat bed cover, scanning starts. − Enable [Scan] Button Specifies whether scanning is started by the [Scan] button.
4.7.6 Filter Set the filter processing in this dialog. The filter name is displayed in the list box. While checking the checkbox in the left of the filter name, the filter processing is applied to scanned image. When selecting a filter name and clicking [Property] button, the setting dialog of the filter is displayed. Figure Option dialog (Filter) The type of filter and the setting details are explained below.
♦ Page Edge Filler Eliminates the blemish around the paper edges by covering the area in (Black or White) color. Color Select a color to paint over the image frame. Can select "White" or "Black". Please specify either white or black to match the background color of the document. Filled Area • [Unit] Select a unit from “Inches”, “Millimeters”, and “Pixels” • [Up], [Down], [Left], [Right] Specify the paint area from each side of the scanned image in numbers.
♦ Digital Endorser Character string, such as the alphabet and number, is added on the data of the scanned image. By using this filter, you can attach a name, a date, a time or a serial number on the scanned images and manage them. Printing Specify the beginning position of the character string to output on the scanned image data. X Offset: Specify the position of the width direction from the left end of document. Y Offset: Specify the position of the length direction from the top of document.
Symbols Other : !”#$%&’()*+,-./:;<=>?@[\]^_`{|}~ : (Space) (*The space is ignored when it is entered at the head of [String:].) The following definitions can be used. They may also be selected from the menu, which is displayed by clicking on " ". %YYYY: The year is printed in four digits using the Western calendar. %YYY: The year is printed using the two digits of the Japanese calendar (current, or Heisei era). %YY: The year is printed in the last two digits of the Western calendar.
4.7.7 Compression Click this tab and mark the check box to enable or disable JPEG compression for data transfer from the image scanner. (This function is available only for Color or Grayscale scans.) Figure Option dialog (Compression) ♦ Imprinter String (Endorser) Converts scanned image data into JPEG format for transfer. Because of smaller data size, data transfer time is shorter than that of ordinary method (when the check box is not marked).
4.8 Setting Advance Options The "advance dialog" is used to set items related to image processing. The settings apply to device-specific functions and items that differ according to whether the scanner used supports them. The advance option specification is divided into "Color Variance", "Image Processing", and "Auto Binary". The supported options depend on the scanner. See "Relevant Image Scanner Specification" in the Appendix. ( is displayed for options that cannot be used.
The options are described below: 4.8.1 Gray Figure Advance dialog (Gray) ♦ Gamma Pattern This option corrects distortions from nonlinear image representation. Scanner sensors are generally designed to generate output linear to the density of the light reflected from the document. However, most output terminals do not produce output that has the desired linear relation to the input, and the resulting distortion must be corrected.
Select the gamma pattern download file to be used from the list of file names. Then, press the [OK] button. Correction will then be executed using the selected gamma pattern. If the gamma pattern download file has not been registered in the list of file names, use the [Add] button to register the file. See "Download Pattern File" for information about how to specify the file. When "Custom" is selected, a custom specification can be entered. Entering an arbitrary value between 0.1 and 10.
Original Image A color sample will be shown. The dropout color can be selected by clicking the desired color with your mouse. Dropout Image An image without the dropout color will be shown. Dropout Color Both the color values and the color will be shown. You can change the color by inputting the color values directly or using the [ ] / [ ] buttons. Priority Black Check this check box when you do not want to dropout some characters.
[File] button Displays arbitrary image files (*.bmp format) on the “Original Image”. [Apply] button Reflects the contents that have been set and closes the window. [Cancel] button Discards the contents that have been set and closes the window. These functions may not be supported depending on the scanner model. Refer to “Image scanner specification” attached to the Appendix. ♦ Reverse This option specifies whether to reverse the black and white of a scanned image.
4.8.2 Image Filter Figure Advance dialog (Image Filter) ♦ Edge Processing This option specifies the sharpness of a scanned image. Select "None", "Edge Extract", or "Smoothing (Background Removal)". None Edge processing is not performed. Edge Extract This option outputs an image with the edge extracted. If this option is selected, the boundary between the black part and white part in a closed area is traced and the edge extracted. "DTC Variance" and "Edge Extract" are mutually exclusive.
Emphasis This option outputs an image with the edge emphasized. "Emphasis High", "Emphasis Mid", or "Emphasis Low" can be selected. If "Emphasis High" is selected, the image becomes sharper. If "Emphasis Low" is selected, the image appears less distinct. ♦ Mirror This option specifies whether to flip the scanned image over the scanning axis. If this option is selected, a mirror image of the original image is obtained.
4.8.3 DTC This option is valid only when "DTC Variance" is set. Figure Advance dialog (DTC Mode) ♦ Scan mode This option selects one of the following two scan modes: [for OCR]: This mode is for text recognition applications where irregularity in the image is undesirable. [for Image]: This mode is for image scanning applications that scan images without prior smoothing. The specification changes the specifiable items and members for "Threshold Curve" and "Gamma Curve".
♦ Threshold Curve This option specifies the relationship between the threshold value and the maximum density. The specification method depends on the [Scan mode] setting. In [for OCR] mode, use the scroll bar to set the inclination and density level between 0 and 5. Click the arrow of the scroll bar or drag the scroll marker to the desired setting position. The current setting is displayed in the center (figure on the left). In [for Image] mode, select [Normal] or [Light] (figure on the right).
♦ OCR Smoothing/ Background Removal The OCR smoothing is the function to make smooth the notched part of line-drawing, and the Background Removal is the function to remove the uneven background. These functions are enabled when it is selected. For further information, please refer to the User’s guide attached to the IPC board since the function to be operated is different by the type of IPC. At IPC-3/3D, [Noise Removal] and [OCR smoothing/ Background removal] is enabled exclusively.
4.8.4 When Color (/Grayscale) is specified For color scanners, when “Color” is selected in the [Image Mode], the [Advance] dialog changes as follows. And in case of some color scanners, when selecting “Grayscale” the [Advance] dialog change as same as selecting “Color”. There are two image samples which are “Sample (before processing)” and “After (after processing)” on this dialog. When you change a setting item, the effect of the setting item is reflected in the image “After”.
♦ Contrast/Brightness (Color / Grayscale) Contrast : Sets the contrast of light and shadow in a scanned image. Specify the contrast with a number in the range of 1 (low [soft]) to 255 (high [sharp]). If this value is increased, the dark part of the image is shown darker and the light part is shown lighter. Some scanner models do not support this function. See "Relevant Image Scanner Specification" in Appendix. Brightness : Sets the brightness of the overall image.
When "Download Pattern" is selected, the above dialog box opens. Select the gamma pattern download file to be used from the list of file names. Then, press the [OK] button. Correction will then be executed using the selected gamma pattern. If the gamma pattern download file has not been registered in the list of file names, use the [Add] button to register the file. See "Download Pattern File" for information about how to specify the file.
Figure Advance dialog ([Quality] / [Gray] tab) ♦ Image Emphasis (Color only) This option specifies the sharpness of a scanned image. Select "None", "De-Screen" or "Emphasis". None Edge processing is not performed. Emphasis This option outputs an image with the edge emphasized. "Emphasis High", "Emphasis Mid", or "Emphasis Low" can be selected. If "Emphasis High" is selected, the image becomes sharper.
♦ White Level Follower (Color) Select this option to scan a document whose background color is not white, such as a newspaper. Select "Auto", "Enable", or "Disable". When "Enable" is selected, the document is scanned using background follow-up (for line drawings). When "Disable" is selected, the document is scanned using the standard basic white background (for photographs). When "Auto" is selected, the option automatically switches to the optimal setting based on the specified "Image Mode".
Original Image A color sample will be shown. The dropout color can be selected by clicking the desired color with your mouse. Dropout Image An image without the dropout color will be shown. Dropout Color Both the color values and the color will be shown. You can change the color by inputting the color values directly or using the [ ] / [ ] buttons. Priority Black Check this check box when you do not want to dropout some characters.
[File] button Displays arbitrary image files (*.bmp format) on the “Original Image”. [Apply] button Reflects the contents that have been set and closes the window. [Cancel] button Discards the contents that have been set and closes the window. These functions may not be supported depending on the scanner model. Refer to “Image scanner specification” attached to the Appendix.
4.9 Setting the Setting Manager Options These options are used to manage the setting files, and switch the basic scan dialog display. Press the [Config...] button of the main dialog to open the [Configuration] dialog box shown below. Figure Configuration dialog box ♦ Setting Files The setting information of the scan conditions can be saved in a “Setting file.” Scan condition settings that have been set in advance in this dialog can be selected from the list of setting files.
♦ FTS File Information The information of the setting file selected in [Setting Files] is displayed. ♦ [Show this dialog next open] checkbox If this checkbox is checked, [Basic Scan Dialog] will be activated the next time the driver is activated. ♦ [OK] button Makes the new setting valid, closes this dialog box, and returns to the main dialog. ♦ [Add] button Adds the setting of the current driver to a setting file. Pressing the [Add] button opens the [File addition] dialog.
♦ [Delete] button Deletes unnecessary setting files. Select the setting file to be deleted and then press the [Delete] button. A confirmation dialog will be displayed. Press the [OK] button to delete the setting file. To cancel, press the [Cancel] button. ♦ [Help] button Displays online help. ♦ [Initialization] button All of scan settings are returned to the initial value.
4.10 Basic Scan Dialog The basic scan dialog contains only the minimum functions required for scanning. The detailed setting functions of the main dialog have been omitted. Scanning can be easily performed by selecting a registered setting file. The basic scan dialog is also useful for avoiding incorrect operations when standard work is performed.
♦ FTS File Information The contents of the selected file are displayed. ♦ [Scan] button Executes scanning based on the contents of the setting file. ♦ [OK] button Terminates without performing the scan operation. ♦ [Adjust] button Switches from the basic scan dialog to the main dialog. ♦ [Help] button Displays online help. ♦ [Show this dialog next open] checkbox If this checkbox is checked, the [Basic Scan Dialog] will be opened at the next startup.
4.11 Download Pattern File The "download pattern file" of this driver is a file that defines the patterns to be used by the scanner to execute various image processing. This file is available in the following two versions. Each version can be selected using the [Download Selection Dialog] that opens when [Download] is selected. The file is a text file that conforms to the following rules. Use an appropriate text editing program (for example, "Note Pad" in the operating system) to edit the file.
Example: In case of 8x8 matrix 8, 8, 128, 128, 128, 128, 128, 128, 128, 128, 255, 128, 128, 128, 128, 128, 128, 128, 255, 255, 128, 128, 128, 128, 128, 128, 255, 255, 255, 128, 128, 128, 128, 128, 255, 255, 255, 255, 128, 128, 128, 128, 255, 255, 255, 255, 255, 128, 128, 128, 255, 255, 255, 255, 255, 255, 128, 128, 255, 255, 255, 255, 255, 255, 255, 128, 8 elements 80 8 elements
♦ Gamma download pattern file Any user defined gamma correction processing can be performed by downloading the pattern from the gamma download file to the scanner. The defined pattern becomes effective when [Download Pattern] is selected for [Gamma Pattern]. Some models do not support this file. See "Relevant Image Scanner Specification" in Appendix. Although the standard extension of the file name is ".
Example 256, 256, 255, 254, 253, 252, 251, 250, 249, 248, 247, 246, 245, 244, 243, 242, 241, 240, 239, 238, 237, 236, 235, 234, 233, 232, 231, 230, 229, 228, 227, 226, 225, 224, 223, 222, 221, 220, 219, 218, 217, 216, 215, 214, 213, 212, 211, 210, 209, 208, 207, 206, 205, 204, 203, 202, 201, 200, 199, 198, 197, 196, 195, 194, 193, 192, 191, 190, 189, 188, 187, 186, 185, 184, 183, 182, 181, 180, 179, 178, 177, 176, 175, 174, 173, 172, 171, 170, 169, 168, 167, 166, 165, 164, 163, 162, 161, 160, 159, 158, 157,
5. Using the Gamma Pattern Editor 5.1 Start-up Click on [Start] and select [Gamma Pattern Editor] from "Scanner Utility for Microsoft Windows" under [Programs].
5.2 [File] menu ♦ [Load...] This menu is used to read the Gamma Download file and display the graph and gradations. The name of the open file is displayed above the graph area. ♦ [Save] The gamma pattern currently being edited is saved in the file whose name is displayed above the graph area. If no filename is displayed, the pattern is named and saved in that file. ♦ [Save As...] The gamma pattern currently being edited is named and saved in that file.
5.4 Gamma Pattern Editing ♦ Graph Area The graph area is a 256-dot x 256-dot white square area bordered by black lines, where the relationship between the input values of 0 to 255 (x axis) and output values of 0 to 255 (y axis) is indicated in blue lines. Each graph dot represents one division (unit). ♦ Gradation The input is displayed in black and white in 256 single-dot steps from 0 at the left border to 255 at the right border. The gamma function of the scanner is displayed.
6. Definition of Scanner and Camera Properties 6.1 Displaying Scanner and Camera Properties Double-click the [Scanner and Camera] icon on the [Control Panel] to display the corresponding Properties dialog box. If the scanner driver has been properly installed, the icon of your scanner is displayed. Select ® ® the model name. And double-click the icon (for Windows 98, Windows 2000) or select the ® ® [Properties...] by using right-click (for Windows Me, Windows XP).
6.3 Events Tab On the Events tab, an application can be specified to be started automatically by “Scanner events” such as “pushing buttons on the scanner”. (The Events tab is not displayed if the device does not support this function.) ♦ Scanner events Select a “scanner event” from the list box to start an application. Please select the item to set up from the following events. "Start button" or "Scan button": When pushing the "Start" or the "Scan" button of the scanner.
In Windows® XP or Windows ServerTM 2003, the following “Events” screen may be displayed. (*This screen has the same function as the above screen.) ♦ Select an event Select a “scanner event” from the list box to start an application. Please select the item to set up from the following events. "Start button" or "Scan button": When pushing the "Start" or the "Scan" button on the scanner. "Send to1-9": ♦ When pushing the "SendTo" button of the scanner.
6.4 Diagnostic Tab To perform more detailed diagnostic tests than those provided in the general tab folder, click the [Diagnose] button. ® ® TM In Windows 2000, Windows XP or Windows Server 2003, only a user who has administrator authority can run these tests.
6.5 Device Information Tab A list of the functions compatible with the selected scanner driver is displayed. The items displayed depend on the selected model of scanner. Only hardware functions are displayed. The functions realized by software are not displayed in this tab folder. Therefore, the displayed content may not match the content specified during reading. The contents of this tab folder are not displayed if the scanner driver is either currently in use or not connected to the computer.
6.6 Device Setup Tab Information related to the operation and maintenance of the scanner driver can be displayed and set up. For some scanner models, this tab may not be displayed, or some items cannot be set up (grayed out). Changing the setup activates the Apply button. The changed setup is reflected on the device only if the Apply button or OK button is clicked. The contents of this tab folder are not displayed if the scanner driver is either currently in use or not connected to the computer.
When using a scanner, the following message may be displayed. If this message appears, replace consumables following the instructions below. < If replacing consumables immediately > 1. Check [This message not display again.] 2. In cases where consumables are replaced after completing all documents being scanned, click [Ignore]. In cases where scanning is stopped for an immediate replacement, click [Cancel]. 3. Following the operator’s guide of the device, replace the consumables. 4.
[Power saving mode] button This specifies the power saving mode. If this button is clicked, the following dialog box is displayed. − Quick Start Mode This mode keeps the lamp on regardless the scanner’s operating condition, which saves times for lamp to become steady. − Low Power Mode To save the power consumption, this mode turns the lamp off, if the scanner is not operated for 14 minutes. * This button may not be displayed for some scanner models.
Enable (Detection Area Selection) Vertically select an area where multifeed detection will or will not be conducted. Choose either “Select area for applying Multifeed Detection” or “Select area for not applying Multifeed Detction”. − Select area for applying Multifeed Detection Select an area for multifeed detection. − Select area for not applying Multifeed Detection Select an area not to be detected. − Start Set start position as distance from the document’s top edge.
[Offset] button When this button is clicked, the following dialog box is displayed. Using this dialog box, the offset of the leading edge and magnification for the sub-scanning direction can be changed. − Offset Setting: If the position of the scanned image shifts from the original document, fine adjustment is possible. At shipment, the offset has been adjusted to an optimum value within a certain range. Therefore, adjustment is not generally required. *The maximum size of changes depends on the device.
− [OK] button The adjusted value is written to the EEPROM. * This button may not be displayed depending on the scanner model. The available settings also vary depending on the scanner model. (e.g. For fi-4110CU, only the setting of the ADF part can be changed) Changing this setting affects scanning operation of the scanner device greatly. Care must be taken when changing.
6.7 About Tab The version of this driver and a link to the Fujitsu home page are displayed. 6.8 Color Management Tab Color profiles assigned to the device can be added or deleted from this folder. "sRGB Color Space Profile.icm" is the default driver assigned to this driver.
6.9 Scanning by using “Scanner and Camera Wizard” In case of Windows XP or Windows Server Camera Wizard”. TM 2003, you can scan by using “Scanner and (* It functions when scanning with supported scanner.) Follow below procedure to scan: 1. On the [Start] menu, select [Control Panel] – [Scanners and Cameras]. 2. Double-click on your scanner’s icon. 3. Click [Next] button when Scanner and Camera Wizard appears. 4. Specify the scan settings and click [Next] button on the following window.
5. Specify a file name, a format and a place to save scanned images. And click [Next] button. Scanning starts. (The following window is displayed during scanning.) 6. Select an item of “What do you want to do?” to keep working with your picture. And click [Next] button. Click on this, and Windows Help appears. * Refer to Windows Help for detail. 7. Select “Nothing, I’m finished working with these pictures when you want to finish. And click [Next] button.
8. Click [Finish] button to finish this wizard.
7. Troubleshooting 7.1 Error Messages 7.1.1 Messages from the TWAIN Driver • The input value is outside the range. Cause: A value exceeding the range allowed for an input item was input. User response: Input a value inside the allowed range. Refer to the input item or the image scanner specification for the range. • The input value is not acceptable. Cause: A value exceeding the range allowed for an input item was input. User response: Input a value inside the allowed range.
• The value for custom paper is higher than the maximum scan size. Width needs to equal 279 mm or less and length needs to equal 420 mm or less. • The value for custom paper is higher than the maximum scan size. Width needs to equal 11 inch or less and length needs to equal 16.53 inch or less. • The value for custom paper is higher than the maximum scan size. Width needs to equal xxx pixel or less and length needs to equal xxx pixel or less.
• Cannot specify Individual Setting with Gray Scale. • Cannot specify Long Page Scan with Gray Scale. Cause: Gray Scale and Individual Setting are specified at the same time. Gray Scale and Long Page Scanning are specified at the same time. User response: Uncheck Individual Setting when specifying Gray Scale. At Long Page scanning, select Black/white binary or Half tone for the [Image type]. • Your application using may not support page end detection, or undefined image size function.
• Specified string is too long. Cause: The specified string is too long. Up to 128 en-size characters and up to 64 em-size characters can be specified. User response: User response: Reduce the number of characters in the string so that they do not exceed 128 en-size characters. Then, try scanning again. • Cannot specify next words for filename. \:;?”<> |. Cause: The specified filename contains one or more of the following characters: \:;?”<> |.
User response: 1. Check the power supply of the scanner or connection with PC. 2. Close other application or “Scanner and Camera” in [Control Panel] • An input-output error occurred in the image scanner. Cause: A fault occurred during the scan operation of the image scanner. There may be a fault in the image scanner itself. User response: Turn off the power of all devices, then turn on the power of the computer before turning on the scanner and retry scanning.
• Insufficient buffer memory size of scanner device for current scanning parameters. Please reduce the scanning area or the resolution, or install additional memory in the scanner. Cause: A memory option has not been installed in the image scanner. Otherwise, a large area or resolution that is not supported by the image scanner has been specified. The memory inside the scanner may be insufficient due to the excessive data size of the scanning image. User response: Reduce the scanning area or resolution.
• Ink cartridge is not installed in the imprinter properly. Please check the installation and try again. Cause: The imprinter (Endorser) has no ink cartridge or the ink cartridge may be mounted improperly. User response: Check that the ink cartridge of the imprinter is mounted properly and scan again. • Imprinting position is set out of paper. Please check the imprinting position and try again. Cause: Printing is not available because the printing part is outside the paper width.
• An error occurred in the temporary file. Cause: Accessing the internal temporary file of the scanned image is causing the error. The disk space may be insufficient, the temporary file may be damaged, or other programs may be affecting disk access. User response: Increase the free space of the disk. Check the hard disk (chkdsk and scandsk). Make sure that no other program is accessing the disk.
• A parameter error has occurred (internally) • The calling procedure is invalid (internally). • The area is specified incorrectly (internally). • The calculation result exceeded the value that can be expressed (internally). • User definition is not registered (internally). • Illegal value is received during communication with scanner. (internally). Cause: This is a program error that occurs during command exchange between the driver and the image scanner.
• An undefined error occurred • Processing cannot be continued because of insufficient memory. • The data source cannot be found. • The driver is connected to a maximum number of applications supported. • An operation error occurred. • An invalid function is specified. • Unpermitted combination of MSG DG DAT. • An invalid value is specified. • An invalid procedure of DG DAT MSG is specified.
7.1.2 Error messages relating to gamma correction pattern editing • Enter a positive decimal value. Cause: A value other than a number has been entered as the gamma correction value. Alternatively, 0 or a negative value has been entered. User response: Reenter a valid value. • The file could not be created. Cause: The file for saving could not be created. There is insufficient space to save the file or the disk to which the file was to be saved is corrupted.
7.2 Device Trouble Related to Operation • The [Scan] button is pressed, but scanning is not performed. Cause: Has the scanner power been turned on? Has the SCSI cable been connected correctly? Has the correct device type been selected using [Select TWAIN Input Device]? • The scanner appears to be operating, but no image is displayed.
7.3 Device Trouble Related to Installation • Can not install the driver. (The installation is stopped on the way.) Cause: User response: Is the older version FUJITSU TWAIN driver .installed in your PC? Please install the driver after uninstalling the old versions. • Though the PC is activated after connecting the scanner device, the scanner device is not detected automatically. Cause: Check the followings 1.
8. Appendix 8.
Individual setting: Disabled Interface: USB 1.
Product: M3091DC (fi-4110C) Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning Light source: Fluorescent tube (White) Basic resolution: 300 dpi 1 Output resolution : 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Color (24bit) output: Enabled 2 ADF scanning speed :
Interface: SCSI-II Preview: Enabled (at ADF scanning) Flip Side Rotation: Enabled Rotation: Enabled Automatic Size and Skew detection: Disabled Overscan: Disabled Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled Batch Detection: Disabled Multifeed detection: Disabled Pre-Pick: Disabled Check Over-skew: Disabled Blank page skip: Enabled (only when ram cache is used) JPEG Transfer (Hardware Compression): D
Product: fi-4110CU Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning Light source: Fluorescent tube (White) Basic resolution: 600 dpi 1 Output resolution : 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Color (24bit) output: Enabled 2 ADF scanning speed : B/W Sin
Interface: USB 1.
Product: fi-4120C Type: Desktop Image sensor: Color CCD (Reduced optical system) Operating method: Automatic Document Feed (ADF), Simultaneous double-sided 1 scanning , Long page scanning Black&White : Max 216mm x 711mm 2 : Max 216mm x 610mm Grayscale, Color Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matr
Gamma pattern: Internal types are not available. (Cannot be downloaded) At custom specification, entering a value enables to set a pattern. Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen, Edge emphasis, 256 Color, 8 Color Individual setting: Disabled Interface: SCSI-II, USB1.
Product: fi-4120C2 Type: Desktop Image sensor: Color CCD (Reduced optical system) Operating method: Automatic Document Feed (ADF), Simultaneous double-sided 1 scanning , Long page scanning : Max 216mm x 864mm Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Color (24
Individual setting: Disabled Imprinter (Endorser): With Imprinter option 1 (Reverse side, minimum left margin printing position of 5mm) Maximum number of characters to be printed: 40 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) Direction(Printing): Top to Bottom Font (orientation) : Vertical / Horizontal Bold font : Enabled Interface: SCSI-II, USB1.1/2.
Product: M3092DC (fi-4210C) Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed Flat bed (FB), Automatic Document Feed (ADF), Simultaneous double-sided scanning Light source: Fluorescent tube (White) Basic resolution: 600dpi (FB), 300 dpi (ADF) 1 Output resolution : 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Col
Interface: SCSI-II Preview: Enabled (at Flat bed scanning, ADF scanning) Flip Side Rotation: Enabled Rotation: Enabled Automatic Size and Skew detection: Disabled Overscan: Disabled Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled Batch Detection: Disabled Multifeed detection: Disabled Pre-Pick: Disabled Check Over-skew: Disabled Blank page skip: Enabled (only when ram cache is used) JPEG Transfer (Hardw
Product: fi-4220C Type: Desktop Image sensor: Color CCD (Reduced optical system) Operating method: Document fixed Flat bed (FB), Automatic Document Feed 1 (ADF), Simultaneous double-sided scanning , Long page scanning Black&White : Max 216mm x 711mm 2 : Max 216mm x 610mm Grayscale, Color Light source: Fluorescent tube (White) Basic resolution: 600dpi Output resolution: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Ha
High light / Shadow : 255 steps (at Color / Grayscale scanning) Gamma pattern: Internal types are not available. (Cannot be downloaded) At custom specification, entering a value enables to set a pattern. Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen, Edge emphasis, 256 Color, 8 Color Individual setting: Disabled Interface: SCSI-II, USB1.
Product: fi-4220C2 Type: Desktop Image sensor: Color CCD (Reduced optical system) Operating method: Document fixed Flat bed (FB), Automatic Document Feed 1 (ADF), Simultaneous double-sided scanning , Long page scanning : Max 216mm x 864mm Light source: Fluorescent tube (White) Basic resolution: 600dpi Output resolution: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded
Gamma pattern: Internal types are not available. (Cannot be downloaded) At custom specification, entering a value enables to set a pattern. Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen, Edge emphasis, 256 Color, 8 Color, 4bit Grayscale Individual setting: Disabled Interface: SCSI-II, USB1.1/2.
1 Product: M3093GX (device name: fi-4320S, VSP210) Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed, scanner unit moving (flat bed), Automatic Document Feeder (ADF) Light source: Xe discharge tube (Green) Basic resolution: 400 dpi Output resolution: Standard: 400, 300, 240, 200 dpi With image processing option: 50 dpi to 800 dpi (at steps of 1 dpi) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither
Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled Batch Detection: Enabled Multifeed detection: Disabled Pre-Pick: Disabled Check Over-skew: Disabled Blank page skip: Enabled (only when ram cache is used) JPEG Transfer (Hardware Compression) : Disabled Filter: Page Edge Filler Drop out color: Disabled sRGB output : Disabled Use Image Processing Software Option: Disabled Scanner and Cameras Wizard: Disabled 1
Product: M3093DG (fi-4320, VSP220) Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed, scanner unit moving (flat bed) Automatic Document Feeder (ADF) Simultaneous double-sided scanning Light source: Xe discharge tube (Green) Basic resolution: 400 dpi Output resolution: Standard: 600 , 400, 300, 240, 200, 150, 100 dpi With image processing option: 50 dpi to 800 dpi (at steps of 1 dpi) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Enabled (8
Rotation: Enabled Automatic Size and Skew detection: End of Page Detection Overscan: Disabled Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled Batch Detection: Enabled Multifeed detection: Disabled Pre-Pick: Disabled Check Over-skew: Disabled Blank page skip: Enabled (only when ram cache is used) JPEG Transfer (Hardware Compression) : Disabled Filter: Page Edge Filler Drop out color: Disabled sRGB output :
Product: fi-4340C Type: Desktop Image sensor: Color CCD, Reduced optical system Operating method: Document fixed Flat bed, Automatic Document Feed(ADF), Simultaneous double-sided scanning Long page scanning (216mm x 1541mm, Black&White only) Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: Standard: 50 dpi to 800 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis, Edge extraction, De-Screen, SEE(Selectable Edge Enhancement), Reverse image, 256 Color, 8 Color With image processing option Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal, Automatic Separation Individual setting: Enabled (Brightness / Threshold / Contrast) Imprinter (Endorser): With imprinter option 1 (Reverse side, minimum left margin printing position of 7 mm) Maximum number of characters to be printed: 40 c
Product: fi-4530C Type: Desktop Image sensor: Color CCD Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning (Resolution free) Black&White : Maximum 297mm x 864mm Grayscale, Color : Maximum 297mm x 864mm Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: 50 - 600 dpi (at steps of 1 dpi) Grayscale levels (internal): 10 bit 1024 levels Gray scale (8 bits) output: Enabled Halftone Patterns: Dither matrix (can
Image processing function: Simplified Dynamic Threshold (SDTC) Edge emphasis, Edge extraction, De-screen, 256 color, 8 color, Reverse image Individual setting: Disabled Imprinter (Endorser): With Imprinter option 1 (Reverse side, minimum left margin printing position of 5mm) Maximum number of characters to be printed: 40 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) Direction(Printing): Top to Bottom Font (orientation) : Vertical / Horizontal 2 B
1 Product: M3096GX (fi-4620S, VSP310) Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed, scanner unit moving (flat bed), Automatic Document Feed (ADF) Light source: Xe discharge tube (Green) Basic resolution: 400 dpi Output resolution: Standard: 400, 300, 240, 200 dpi With image processing option: 50 dpi to 800 dpi (at steps of 1) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be dow
Overscan: Disabled Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled Batch Detection: Enabled Multifeed detection: Disabled Pre-Pick: Disabled Check Over-skew: Disabled Blank page skip: Enabled (only when ram cache is used) JPEG Transfer (Hardware Compression) : Disabled Filter: Page Edge Filler Drop out color: Disabled RGB”s output :w Disabled Use Image Processing Software Option: Disabled Scanner and Came
Product: fi-4640S Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed Flat bed, Automatic Document Feed(ADF) Long page scanning (297mm x 1387mm, Black&White only) Light source: Xe discharge tube(Green) Basic resolution: 400 dpi Output resolution: Standard: 50 dpi to 800 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Flat bed scan
Individual setting: Disabled Imprinter (Endorser): With imprinter option 1 (Reverse side, minimum left margin printing position of 42 mm) Maximum number of characters to be printed: 40 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) Direction (Printing): Top to Bottom, Bottom to Top Interface: SCSI-II Preview: Enabled (at Flat bed scanning only) Flip Side Rotation: Disabled Rotation: Enabled Automatic Size and Skew detection: End of Page Det
Product: M4097D (fi-4750, VSP330) Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed Flat bed, Automatic Document Feed(ADF), Simultaneous double-sided scanning Long page scanning (297mm x 1387mm, Black&White only) Light source: Xe discharge tube(Green) Basic resolution: 400 dpi Output resolution: Standard: 50 dpi to 800 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix
Imprinter (Endorser): With imprinter option 1 (Reverse side, minimum left margin printing position of 42 mm) Maximum number of characters to be printed: 40 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) Direction (Printing): Top to Bottom, Bottom to Top Interface: SCSI-II Preview: Enabled (at Flat bed scanning only) Flip Side Rotation: Enabled Rotation: Enabled Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Dete
Product: fi-4750L Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed Flat bed, Automatic Document Feed(ADF), Simultaneous double-sided scanning Long page scanning (297mm x 1387mm, Black&White only) Light source: Xe discharge tube(Green) Basic resolution: 400 dpi Output resolution: Standard: 50 dpi to 800 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloa
Imprinter (Endorser): With imprinter option 1 (Reverse side, minimum left margin printing position of 42 mm) Maximum number of characters to be printed: 40 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) Direction(Printing): Top to Bottom, Bottom to Top Interface: SCSI-II Preview: Enabled (at Flat bed scanning only) Flip Side Rotation: Enabled Rotation: Enabled Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detec
Product: fi-4750C Type: Desktop Image sensor: LED(RGB) + Reduced optical system Operating method: Document fixed Flat bed, Automatic Document Feed(ADF), Simultaneous double-sided scanning Long page scanning (297mm x 1387mm, Black&White only) Light source: LED (R, G, B) Basic resolution: Horizontal scanning: 400 dpi Vertical scanning: 800,700,600,500, 400, 300, 240, 200, 150, 100 dpi Output resolution: Standard: 50 dpi to 800 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 leve
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis, Edge extraction, De-Screen, SEE(Selectable Edge Enhancement), Reverse image, 256 Color, 8 Color With image processing option Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal, Automatic Separation Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern / Image processing function) Imprinter (Endorser): With imprinter option 1 (Reverse side, minimum left margin printing
1 Product: M3097G Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed, scanner unit moving (flat bed), Automatic Document Feed (ADF) Light source: Fluorescent tube (Green) Basic resolution: 400 dpi Output resolution: Standard: 400, 300, 240, 200 dpi With image processing option: 50 dpi to 1,600 dpi (at steps of 1) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Enabled (8 bits) Some release version of scanner do not support gray-scale output
Automatic Size and Skew detection: Disabled Overscan: Disabled Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled Batch Detection: Enabled Multifeed detection: Disabled Pre-Pick: Disabled Check Over-skew: Disabled Blank page skip: Enabled (only when ram cache is used) JPEG Transfer (Hardware Compression) : Disabled Filter: Page Edge Filler Drop out color: Disabled sRGB output : Disabled Use Image Processing
Product: M3097DG Type: Desktop Image sensor: Reduced optical system Operating method: Document fixed, scanner unit moving (flat bed), Automatic Document Feed (ADF) Simultaneous double-sided scanning Light source: Xe discharge tube (Green) Basic resolution: 400 dpi Output resolution: Standard: 600, 400, 300, 240, 200, 150, 100 dpi With image processing option: 50 dpi to 800 dpi (at steps of 1 dpi) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Enabled (8 bits) Halftone Patt
Rotation: Enabled Automatic Size and Skew detection: End of Page Detection Overscan: Disabled Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled Batch Detection: Enabled Multifeed detection: Disabled Pre-Pick: Disabled Check Over-skew: Disabled Blank page skip: Enabled (only when ram cache is used) JPEG Transfer (Hardware Compression) : Disabled Filter: Page Edge Filler Drop out color: Disabled sRGB output :
Product: fi-4860C Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning (297mm x 878mm, Black&White only) Light source: Fluorescent tube (White) Basic resolution: 400 dpi Output resolution: Monochrome: 400, 300, 240, 200, 150, 100dpi Color: 400, 300, 200, 150, 100dpi Grayscale levels (internal): 10 bit 1024 levels Gray scale (8 bits) output: Enabled Halftone Patterns: Dither matrix, Error
Image processing function: Dynamic Threshold (SDTC, DTC), Edge emphasis, Edge extraction, Automatic separation, Mirror image(Black&White only), Reverse image, 256 Color, 8 Color Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern / Image processing function) Imprinter (Endorser): With Imprinter option (Pre-Imprinter / Post-Imprinter) 1 (Reverse side, minimum left margin printing position of 5 mm) Maximum number of characters to be printed: 40 characters
Product: M4099D (fi-4990) Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning (297mm x 878mm, Black&White only) Light source: Fluorescent tube (White) Basic resolution: 400 dpi Output resolution: Standard: 400, 300, 240, 200, dpi With image processing option: 50 dpi to 400 dpi (at steps of 1 dpi) Grayscale levels (internal): 10 bit 1024 levels Gray scale (8 bits) output: Enabled (200 dpi o
Individual setting: Enabled (Brightness / Threshold / Contrast / Gamma pattern / Image processing function) Imprinter (Endorser): With endorser option 1 (Reverse side, minimum left margin printing position of 20 mm) Maximum number of characters to be printed: 30 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) (There are partly limitations by the revision of the scanner device.
Product: fi-4990C Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning (297mm x 878mm, Black&White only) Light source: Fluorescent tube (White) Basic resolution: 400 dpi Output resolution: Monochrome: 400, 300, 240, 200, 150, 100dpi Color: 400, 300, 200, 150, 100dpi Grayscale levels (internal): 10 bit 1024 levels Gray scale (8 bits) output: Enabled Halftone Patterns: Dither matrix, Error
Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern / Image processing function) Imprinter (Endorser): With endorser option 1 (Reverse side, minimum left margin printing position of 20 mm) Maximum number of characters to be printed: 30 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) (There are partly limitations by the revision of the scanner device.
Product: M3099G, M3099GX Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning Light source: Fluorescent tube (Green) Basic resolution: Horizontal scanning: 200 dpi Output resolution: Standard: 400, 300, 240, 200, dpi With image processing option: 50 dpi to 400 dpi (at steps of 1 dpi) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Disabled Halftone Patterns: Dither matrix (can be downloaded),
image, Reverse image, Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal Individual setting: Enabled (Brightness / Threshold / Contrast / Gamma pattern / Image processing function) Imprinter (Endorser): With imprinter (endorser) option 1 (Reverse side, minimum left margin printing position of 20 mm) Maximum number of characters to be printed: 20 characters Counter display range: 0 to 65535 (5 digits display) Direction (Printing): Top to Bottom Interface: SCSI-II Preview: Disabled Flip Side
Product: M3099GH Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning Light source: Fluorescent tube (Green) Basic resolution: 200 dpi Output resolution: Standard: 400, 300, 240, 200, dpi with image processing option: 50 dpi to 400 dpi (at steps of 1 dpi) Grayscale levels (internal): 8 bit 256 levels Grayscale output: Disabled Halftone Patterns: Dither matrix (can be downloaded), Error diffusion 1 ADF scann
Imprinter (Endorser): With imprinter (endorser) option 1 (Reverse side, minimum left margin printing position of 20 mm) Maximum number of characters to be printed: 20 characters Counter display range: 0 to 65535 (5 digits display) Direction (Printing): Top to Bottom Interface: SCSI-II Preview: Disabled Flip Side Rotation: Enabled Rotation: Enabled Automatic Size and Skew detection: Disabled Overscan: Disabled Buffer scan ([Use Memory on Scanner]) function: Disabled Use Both Memory ( [Ram Cache
Product: fi-5110C Type: Desktop Image sensor: Color CCD (Reduced optical system) Operating method: Automatic Document Feed (ADF), Simultaneous double-sided 1 scanning , Long page scanning: Max 216mm x 863mm Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Color (24bi
Individual setting: Disabled Interface: USB2.
Product: fi-5120C Type: Desktop Image sensor: Color CCD (Reduced optical system) Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning : Max 216mm x 864mm Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Color (24bit)
Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern) Imprinter (Endorser): With Imprinter option 1 (Reverse side, minimum left margin printing position of 5mm) Maximum number of characters to be printed: 40 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits display) Direction(Printing): Top to Bottom Font (orientation) : Vertical (Normal), Horizontal (Normal / Narrow) Bold font : Enabled Interface: SCSI-II, USB1
Product: fi-5220C Type: Desktop Image sensor: Color CCD (Reduced optical system) Operating method: Document fixed Flat bed (FB), Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning : Max 216mm x 864mm Light source: Fluorescent tube (White) Basic resolution: 600dpi Output resolution: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), E
Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen, Edge emphasis, 256 Color, 8 Color, 4bit Grayscale Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern) Interface: SCSI-II, USB1.1/2.
Product: fi-5530C Type: Desktop Image sensor: Color CCD Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning (Resolution free) Black&White : Maximum 297mm x 864mm Grayscale, Color : Maximum 297mm x 864mm Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: 50 - 600 dpi (at steps of 1 dpi) Grayscale levels (internal): 10 bit 1024 levels Gray scale (8 bits) output: Enabled Halftone Patterns: Dither matrix (can
Image processing function: Simplified Dynamic Threshold (SDTC), Advanced DTC, Edge emphasis, Edge extraction, De-screen, 256 color, 8 color, Reverse image Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern) Imprinter (Endorser): With Imprinter option 1 (Reverse side, minimum left margin printing position of 5mm) Maximum number of characters to be printed: 40 characters Counter display range: 0 to 99999 (at 5 digits display) 0 to 16777215 (at 8 digits di
Product: fi-5650C Type: Desktop Image sensor: Color CCD + Reduced optical system Operating method: Document fixed Flat bed(FB), Automatic Document Feed(ADF), Simultaneous double-sided scanning Long page scanning (305mm x 864mm) Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: Standard: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis, Edge extraction, De-Screen, SEE(Selectable Edge Enhancement), Reverse image(at Black & White, Grayscale), 256 Color, 8 Color Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern / Image processing function) Imprinter (Endorser): With Imprinter option 1 (Reverse side, minimum left margin printing position of 5mm) Maximum number of characters to be printed: 40 characters Counter
Product: fi-5750C Type: Desktop Image sensor: Color CCD + Reduced optical system Operating method: Document fixed Flat bed(FB), Automatic Document Feed(ADF), Simultaneous double-sided scanning Long page scanning (305mm x 864mm) Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: Standard: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis, Edge extraction, De-Screen, SEE(Selectable Edge Enhancement), Reverse image(at Black & White, Grayscale), 256 Color, 8 Color Individual setting: Enabled (Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern / Image processing function) Interface: SCSI-II, USB 2.
Product: fi-5900C Type: Desktop Image sensor: Reduced optical system Operating method: Automatic Document Feed (ADF), Simultaneous double-sided scanning, Long page scanning (305mm x 878mm) Light source: Fluorescent tube (White) Basic resolution: 600 dpi Output resolution: Standard: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 10 bit 1024 levels Gray scale (8 bits) output: Enabled Halftone Patterns: Dither matrix, Error diffusion Color 24bit 1 ADF scanning speed :
Edge Enhancement), Mirror image(Black&White only), Reverse image, 256 Color, 8 Color Individual setting: Enabled (Image Mode / Brightness / Threshold / Contrast / High light / Shadow / Gamma pattern / Image processing function) Multi Image: Multi Image Output / Auto color Detection Imprinter (Endorser): With Imprinter option (Pre-Imprinter / Post-Imprinter) 1 (Reverse side, minimum left margin printing position of 5 mm) Maximum number of characters to be printed: 40 characters (When using 8 digits coun
Operator Panel setting: [Scan] / [Send to] button Prefer Scanning Speed setting: Enabled Device set: Consumables replace (Pad / Pick Roller / Break Roller / Separator Roller / Remaining Ink counter clear) Offset Setting, Vertical magnification Adjustment, Power Saving setting Area Selection for Multifeed Detection Scanner and Camera Wizard: Enabled (Windows XP / Windows Server 176 TM 2003 only)
Product: fi-60F Type: Desktop Image sensor: LED(RGB) + Reduced optical system Operating method: Document fixed Flat bed(FB) Light source: LED (R, G, B) Basic resolution: 600 dpi Output resolution: Standard: 50 dpi to 600 dpi (at steps of 1dpi) Grayscale levels (internal): 16 bit 65536 levels Grayscale output: Enabled (8 bits) Halftone Patterns: Dither matrix (can be downloaded), Error diffusion Color output Enabled (24bit) Flat bed scanning speed: B/W : 1.
JPEG Transfer (Hardware Compression) : Disabled Filter: Page Edge Filler, Digital Endorser Drop out color: Enabled sRGB output : Enabled Use Image Processing Software Option: Enabled Device set: Offset Setting, Vertical magnification Adjustment Scanner and Camera Wizard: Enabled (Windows XP / Windows Server 178 TM 2003 only)
8.2 Maintenance Service This section explains briefly how you can help us to provide you with high-quality maintenance service. Since it is practically impossible for the Fujitsu service staff to be aware of every detail of your daily scanning operation, please understand that our staff may sometimes be unable to answer your question immediately.
FUJITSU TWAIN32 Scanner Driver / Utility “Scanner Utility for Microsoft® Windows®” Users Guide 32 bit version First Edition February 2006 2nd Edition March 2006 3rd Edition June 2006 4th Edition June 2006 All Rights Reserved, Copyright © PFU LIMITED 2006 The contents of this document may change for improvements without prior notice. PFU LIMITED takes no responsibilities for infringements of third parties’ patents or other rights that may stem from the use of the data in this document.
