PRIMERGY RX100 S7p System configurator and order-information guide May 2012 Contents Instructions Configuration diagram Configurator 0 System software I Basic unit II Processor III Memory IV Riser Card V Graphics VI Energy Star VII Accessible drives VIII Hard disk drives IX SCSI / SAS controller X Disk array XI Communication/Network XII System Management Products (RemoteView) XIII Miscellaneous XIV Country specific power cord Change report PRIMERGY Server
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 Instructions This document contains basic product and configuration information that will enable you to configure your system via PC-/System-Architect Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to adjust your specific requirements.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 Configuration diagram PRIMERGY RX100 S7p with 3.5" Hard disk drives System unit ( I ) Standard Power Supply Bank 2 Bank 1 Modul 1 Intel CPU Dual- or Quad-core or Modul 3 1. PSU 2. PSU Redundant PSU option Modul 2 Power supply Modul 4 Processor ( II ) Bay for 3,5"x 0,5" CSS or Front VGA 5.25"x0.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 Configuration diagram PRIMERGY RX100 S7p with 2.5" Hard disk drives System unit ( I ) Standard Power Supply Bank 2 Bank 1 Modul 1 Intel CPU Dual- or Quad-core or Modul 3 1. PSU 2. PSU Redundant PSU option Modul 2 Power supply Modul 4 Processor ( II ) Bay for 3,5"x 0,5" CSS or Front VGA 5.25"x0.
PRIMERGY-Software Configurators and Release Lists PRIMERGY RX100 S7p Status 2012-04-30 Start PRIMERGY RX100 S7 SW - Configurator 32 bit with OEM-Software without OEM-Software for PRIMERGY Server VMWare restrictions 1 onboard LAN is supported for PRIMERGY Server SATA RAID is not supported OEM-SW is bound to HW and is not allowed to be ordered separately.
PRIMERGY-Software Configurators and Release Lists PRIMERGY RX100 S7p Status 2012-04-30 Start PRIMERGY RX100 S7p SW - Configurator EM64T with OEM-Software without OEM-Software for PRIMERGY Server for PRIMERGY Server For all SW products please refer to the corresponding software configurator accessible via the Extranet under "Configuration & Tools, -All configurations, -Software, URL see below.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 Start PRIMERGY RX100 S7p Section 1 I Basic unit System unit including: * 1U Housing * 1 power supply (Standard Ps with 300W or hot plug PSU with 450W) * Fans - Fans for Power Supply and Chassis 4x non hot-plug fans in standard PSU base unit, 5 fans with 1 of 5 redundancy in hotplug PSU base unit * Drives / Bays - 2 bays 3.5" for hot-plug HDDs or - 4 bays 2.5" for hot-plug HDDs - 1 bay 0.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 A Basic unit (for 19" racks) with SATA RAID (can be upgraded by Modular SAS RAID) without CPU and Memory - One CPU ( first CPU ) has to be configured additionally for a base configuration - One memory kit has to be configured for a base configuration SAS/SATA LFF (3.5") version with: - 2-port SAS backplane for 2 hot plug LFF (3.5") SAS/SATA HDDs incl.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 B Section 2 II Processor Note**: The CPU is not included in the base unit and has to be configured separately. One of following CPU´s has to be selected for an orderable basic unit Dual-Core CPU`s - 1x 64-bit Intel Celeron (2MB SLC), Pentium (3MB SLC) or Core-i3 (3MB TLC) occupies socket for one CPU Celeron Celeron G530 2.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 Section VI Energy Star S26361-F3301-E112 RX100 S7 E-Star Fam2 for all 69W 4Core CPUs with std. PSU Limits configuration in accordance with Energy Star requirements The following order components out of the specific sections are allowed together with RX100 S7p E-Star Fam2: max. 1x per system SATA/SAS LFF (3.5") Base Unit with std PSU S26361-K1385-V103 Quad-Core CPU`s Xeon E3-1220v2 3.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 C Section 6 VII Accessible drives Setup PRIMERGY RX100 S7p by ServerStart is supported with following configurations: no DVD, no CD: remote installation only ( PXE service & DHCP server required) built in DVD or USB DVD: UNC Network share reachable or USB Floppy or MemoryBird connected If installation is done locally, make sure you have USB stick available for driver installation.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 D Section 7 VIII Hard disk drives Configurations with Eco SATA can only be mixed with BC SATA HDD type SAS and BC SATA drives with the same size can be mixed, but not used in one logical RAID volume SAS/SATA LFF (3.5") Base Units: SAS HDDs Require SAS Controller! see section "internal Disk Array" There is a 6 port SATA controller in the Base Unit for connection of up to 2 SATA LFF (3.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 F Section 8 IX SCSI/SAS-Controller SCSI/SAS-Controller Low Profile Slot suitable for Low Profile PCIe 2 x PCIe G2 x16 / x4 (wired x1 ) SCSI-controller for external drives and peripheral devices S26361-F3270-E201 SCSI U320 Controller Adaptec SCSI Card 29320LPE PCIe x1, Low Profile int: LVD HD68 ext: VHDCI 68pin max. 1x per system Only released for Windows OS Only released for external backup (LT20).
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 G Sections 9 X Disk Array SATA Configuration SATA Base Units contains a 6-port (5 in use) on-board SATA controller supporting RAID Levels 0, 1, 10 SATA RAID is not supported by VMWare SAS Configuration you can choose between three different SAS controllers for the Base Unit: - LSI 1064e / 2008 based Modular RAID 0,1 (IME) - LSI 2108 based Modular RAID 0, 1, 10, 5, 50, 6, 60 if you want to use SAS harddisks one Control
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 Q X Section Fibre Channel No mix and match of different FC Controllers possible. All controllers for the connection of external storage system are delivered without cables. For the configuration of external cabling see the configurator for external storage system.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 H Section # XI Communication / Network Communication / Network Low Profile 2x Gigabit Ethernet Contr. Teaming: Failover, Load Balancing onboard The Intel LAN Controllers 1000GT, 1000MF, 1000PT, 1000PF Intel LAN 82579 (Lewisville) can be used with the on-board controller in Teaming Mode Using VMWare, only one of both onboard LAN Ports is supported.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 I Section # XII System Management Products (RemoteView) S26361-F1790-E242 iRMC3 advanced pack integrated remote mgmt. controller iRMC S3 (integrated Remote Management Controller) onboard server management with dedicated 10/100/1000 Service LAN-port and integrated graphics controller.
System configurator and order-information guide PRIMERGY RX100 S7p Status 2012-04-30 Change Report Date Order number Changes 2012-04-27 2012-04-20 2012-03-29 2012-03-28 2012-03-23 2012-03-23 2012-03-21 2012-01-25 2011-12-21 2011-11-16 2011-10-01 2011-10-01 2011-08-09 2011-07-29 2011-06-30 2011-06-01 S26361-F3301-E112 Update on Energy Star FCOE / FC HBAs / NVS300 / cougar 3 set to as soon as available SSD 32/64 GB removed since EOL Rack Mount Kit F1-C S7 LV (follower for *-E145; G.