P3PC-2242-04EN fi-6670/fi-6770/fi-6750S Thank you for purchasing a fi-6670 / fi-6770 / fi-6750S Color Scanner series. This Getting Started is the startup guide that summarizes the preparatory actions needed before use. Be sure to thoroughly read this manual before you start using the scanner. Contents Introduction....................................................................2 Regulatory Information .................................................3 Conventions.......................................
Introduction Thank you for purchasing our fi-6670/fi-6770/fi-6750S series Color Image Scanner. Scanner Models This manual covers the following three scanner models, each featuring as: Model Description fi-6670 Equipped with an automatic document feeder (ADF) for automatic document feeding and duplex scanning. fi-6770 Equipped with an automatic document feeder (ADF) for automatic document feeding and duplex scanning, and a flatbed for scanning documents such as thin paper or thick books.
Regulatory Information ENERGY STAR® FCC Declaration PFU LIMITED, a Fujitsu company, has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
■ Operating Systems and Software Products Screen Examples in This Manual The OSs and products in this manual are indicated as follows: Product Indication Windows 2000 Professional (Service Pack 4 or later) Windows Windows 2000 *1 Windows® XP Home Edition (Service Pack 3 or later) Windows XP ® The screen examples in this manual are subject to change without notice in the interest of product improvement.
Safety Information Warning Label Warning Indications Used In This Manual The following indications are used in this manual to obviate any change of accident or damage to you and/or the equipment. WARNING This indication alerts operators to an operation that, if not strictly observed, may result in severe injury or death. HOT warning label: The glass surface inside the ADF becomes hot during the operation. Be careful not to touch glass surfaces inside the ADF.
Make sure to ground the scanner. Do not put liquids inside the scanner. Make sure to ground to avoid electric shock. Be sure to ground before plugging into a Power outlet. Unplug from the outlet before removing the ground connection. Do not insert or drop any metal objects into the ADF slot or ventilation ports on the scanner. Do not scan any wet documents or documents with paper clips or staples attached. Do not splash or allow the scanner to get wet.
CAUTION Avoid any contact when scanner is in use. Avoid getting a sleeve, necktie, or hair caught up in any scanner mechanism during scanning since this may cause injuries. The following are important cautions described in this manual Do not install the scanner on an unstable work table. Disconnect the power plug from the Power outlet when the scanner is not in use for a long period of time. When installing the scanner on a work table, make sure that the table is flat and level.
1 Preparation Contents of the Scanner Package When you unpack the scanner package, make sure that all of the following parts are included in the package. Make sure the scanner package contains all the parts listed in the package contents list that is included in the package box. If any parts are missing or defective, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.
Part Names and Functions This section describes the scanner parts and their functions. For information on the function of each part, refer to “Section 1.2 Scanner Parts and Their Functions” in the Operator’s Guide.
■ fi-6770/fi-6750S (Flatbed type) Chute Roller Cover ADF (automatic document feeder) ADF Paper Chute Stacker Paper Chute Extension Stacker Extension Side Guide Side Guide Button Stopper Operator Panel Flatbed Transport Lock Document Cover ADF Lock Screw Handle Document Holding Pad Lock Screw Storage Hole Document Bed ADF Open Button fi-6770 SCSI ID Switch CGA Board Slot SCSI Connector USB Connector fi-6750S Ventilation Port Power Connector Main Power Switch USB Connector 10
■ Model-Common Parts Brake Roller (x1) (consumable) Pick Arm (x1) Brake Roller Holder (x1) Ultrasonic Sensor (x2) (for multifile detection) Feed Roller (x4) Plastic Roller (x4) Chute Roller (x1) (Usually covered with a hood) Glass (x2) Pick Roller Cover (x1) Sheet Guide (x2) Pick Roller (1 x 2 types) (consumable) Functions of the Operator Panel The Operator Panel is comprised of a Function Number Display, buttons, and LEDs, which are used to operate the scanner and to check the scanner status.
■ Flatbed type Check Check LED Function Number Display Function [Function] button Send to [Send to] button Scan / Stop [Scan/Stop] button Power [Power] button/Power LED Name Description Check LED Lights (in orange) when an error occurs. Function Number Display Indicates the scanner status. [Function] button Switches the function activated by the [Send to] button. [Send to] button Launches linked application software for scanning. Resets an error indication.
2 Installing the Scanner The following describes how to install the scanner. 1 Place the scanner at its installation site. The outer dimensions and the spaces required for installing the respective scanner types are as follows: (Unit: mm/inches) ADF type Flatbed type 390 (15.3) 300 (11.8) 432 (17.0) 686 (27.0) 640 (25.1) 342 (13.4) 700 500 (27.5) (19.6) 329 (13.0) 1179 (46.4) 690 (27.1) 1030 (40.5) Outer dimensions Installation space 2 Unlock the Transport Lock (Flatbed type only).
3) Gently close the Document Cover. 4) Change the position of the ADF. CAUTION • Be careful not to pinch your fingers when moving the ADF. • Never rotate the ADF by more than 180 degree. Doing so may damage the ADF. The ADF can be set to any of the following three positions: After repositioning the ADF, be sure that the ADF is firmly locked to the new position. ■ Traditional (Factory default) ■ Standard (Space-saving type and for right-handed operators) Slide the ADF toward the center of the scanner.
3 Connecting the Cables The following describes how to connect the cables between the scanner and your computer. The type of the connector for the cable depends on the scanner model you use. Confirm the scanner model and use the correct cable.
1 2 3 Make sure that the computer is turned OFF. Open the Cable Cover (ADF type only). Connect the scanner to your computer either with a USB or SCSI cable. • You cannot make both USB and SCSI cable connections at the same time. • You cannot connect multiple computers to the scanner at the same time. • Turn off the scanner and your computer first when you switch the interface cable. The following describes the requirements for connecting with the respective cables.
4 Installing the Scanner Software Brief Information on the Bundled Software To scan documents with this scanner, you must install a scanner driver for operating the scanner as well as scanning software (hereinafter called the "application") for launching the driver and performing a scan. The scanner drivers and applications provided with the scanner are as follows: ■TWAIN Driver Conforms to the TWAIN standard. Used when you operate the scanner using TWAIN-compliant applications.
■QuickScan ProTM (trial) [QuickScan Pro (Trial)] (*1) Conforms to the ISIS standard. By using the ISIS scanner driver together with QuickScan ProTM, you can read scanned documents and create their images. This bundled QuickScan ProTM is a trial version, and can be executed 30 times before it is disabled. You will need to purchase the full product version if you wish to continue using it. ■Manuals Includes Getting Started, and Operator's Guide.
*1: Kofax VRS supports the following Windows Vista versions: - Windows Vista Business - Windows Vista Enterprise - Windows Vista Ultimate Kofax VRS supports the following versions of Windows 7: - Windows 7 Professional - Windows 7 Enterprise *2: Does not support the Windows 64-bit versions.
If an old version of the software is installed already, uninstall it first. For how to uninstall each of the software, refer to “Appendix 5 Uninstalling the Software” in the Operator’s Guide. The following describes how to install the software. 1 Confirm that the scanner is not turned ON. 2 Turn on your computer and log onto Windows. Be sure to log on as a user with "Administrator" privileges. 3 Insert the Setup DVD-ROM into your disk drive. D The [FUJITSU Image Scanner Setup] screen appears.
INSTALL (Custom) This menu lets you select and install the required software programs one by one. The procedure for custom-installing the required software is as follows: If an old version of the software is installed already, uninstall it first. For how to uninstall each of the software, refer to “Appendix 5 Uninstalling the Software” in the Operator’s Guide. 1 Confirm that the scanner is not turned ON. 2 Turn on your computer and log onto Windows.
5 Test-Scanning Documents Using ScandAll PRO, you can test-scan documents to check if they are scanned with the ADF correctly. For how to scan documents with the flatbed, refer to “Chapter 4 Various Documents” in the Operator’s Guide. The following describes how to test-scan a document: 1 Turn on the scanner. 1) Press the “I” side of the main power switch of the scanner. 2) Press the [Power] button on the Operator Panel. The scanner is turned ON, and the Power LED on the Operator Panel lights in green.
4 Load a sheet into the scanner. 1) Load the document on the ADF Paper Chute face down. 2) Align the side guides to the width of the document. 3) Pull out the Stacker to the length of the document, and then raise the Stopper. 5 6 7 8 9 Launch ScandAll PRO. Select the [start] menu D [All Programs] D [Fujitsu ScandAll PRO] D [ScandAll PRO]. Select the [Tool] menu D [Preferences]. D The [Setup] dialog box appears. On the [Scan] tab, select a driver to use, and then click the [OK] button.
When using Kofax VRS for the first time, the [Register Kofax VRS] screen appears. User registration is required to obtain support information from Kofax as well as to upgrade the software, though Kofax VRS can still be used without user registration. To register later, select [Start] menu - [All Programs] - [Kofax VRS] - [Kofax VRS Administration Console], and follow the on-screen instructions.
■ ISIS scanner driver Configure scan settings, and then click the [OK] button. ■ Kofax VRS Configure scan settings, and then click the [OK] button. 14 In the [Scan Settings] dialog box, click the [Scan] button. D The scanned document images are displayed in the ScandAll PRO window. Refer to “Chapter 7 Troubleshooting” in the Operator’s Guide, in case you see a number and an alphabet displayed on the Function Number Display.
fi-6670/fi-6770/fi-6750S Image Scanner Getting Started P3PC-2242-04EN Issue Date: August 2012 Issued by: PFU LIMITED • Copying of the contents of this manual in whole or in part and copying of the scanner application is prohibited under the copyright • The contents of this manual are subject to change without notice. • PFU LIMITED is not liable whatsoever for any damages resulting from use of this scanner and procedures described in this manual, profit due to defects, and any claims by a third party.
