P3PC-3062-02EN
CONTENTS INTRODUCTION ........................................................................... ii Regulatory Information ........................................................ ii Liability ................................................................................. iii Safety Precautions ............................................................... v Chapter1 PREPARING THE SCANNER.................................. 1 1.1 Checking the Contents of the Scanner Package............. 1 1.
INTRODUCTION Thank you for purchasing the fi-5950 Duplex Color Scanner. This document describes how to use fi-5950 and basic operation methods. Before you start using fi-5950 be sure to thoroughly read this manual to ensure correct use.
■ Liability About the use of mercury READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS. Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state, or federal laws. Hg To avoid unexpected injuries; •Do not put the substance contained in the lamp in your mouth as it has mercury. •Do not breathe the chemical liquid contained in the scanner lamps.
Product Windows Server® 2003, Standard Edition, Windows Server® 2003, Standard x64 Edition, Windows Server® 2003 R2, Standard Edition (Service Pack 2 or later), Windows Server® 2003 R2, Standard x64 Edition (Service Pack 2 or later) Windows Server 2003 Windows Vista® Home Basic (32/64-bit) (Service Pack 1 or later), Windows Vista® Home Premium (32/64-bit) (Service Pack 1 or later), Windows Vista® Business (32/64-bit) (Service Pack 1 or later), Windows Vista® Enterprise (32/64-bit) (Service Pack 1 or late
Screen Examples In This Manual The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen while referring to the User's Manual of the scanner application you are using. The screenshots in this manual were captured from TWAIN driver scanner driver, ScandAll PRO Image Capturing Utility Software, ISIS driver and Adobe® Acrobat®.
Do not install the scanner in the following locations which are subject to high temperature, humidity, less ventilation, or dust. If placed in an area subject to high temperature, the cover may become overheated and deformed, causing the scanner to become hot, resulting in a fire. • A place near heat-radiating devices such as stoves or electric heaters, or flammable items such as volatile inflammable materials or curtain.
CAUTION When installing the scanner on a table, make sure that the table is flat and level. Place the scanner so that none of its parts extend beyond the edge of the table, otherwise it may fall or collapse and cause injuries. Install the scanner away from strong magnetic fields and other sources of electronic noise. Protect the scanner against any static electricity and choose a static-free place to install the scanner. Static electricity can cause the scanner to malfunction.
PREPARING THE SCANNER Chapter1 1.1 Checking the Contents of the Scanner Package No. When you unpack the scanner package, make sure that the package contains all the parts on the list included in the package. If any parts are missing or defective, contact your scanner dealer or an authorized FUJITSU scanner service provider. Handle the scanner and accessories with care. 1.2 Names of Parts This section describes the names of parts.
■ Removable Parts 1.3 Operator Panel The operator panel is located on the right side of the scanner. The panel consists of a Function Number Display, buttons and a LED. Function number display 1 Function Hopper Height Function Function Hoppe r Heig ht Thin Power Hoppe r Heig ht Thickn ess Thick Thin Send Powe r Thickn ess to Thick Scan Send Paper Thickness to Scan T Thin Send to No.
Name Scan ■ Indications on the Function Number Display Function Use this button to start linked application. When this button is pressed during scanning operation, the scanning is cancelled (*About the settings, refer to the "fi5950 Operator’s Guide" on the Setup DVD-ROM). The following shows the indications on the Function Number Display. No. Lights only one time upon turning on the scanner. Use this button to turn the power ON/ OFF. When the power is turned on, the button is illuminated in blue.
Chapter2 INSTALLATION OF THE SCANNER 2.1 Installing the Scanner 2.2 Connecting the Scanner to Your PC 1. Place the scanner at its installation site. Connect either using the USB or SCSI interface. For details on the scanner's dimensions and required installation space, refer to the fi-5950 Operator’s Guide, chapter "10. Scanner Specifications". ATTENTION ATTENTION This scanner is provided with two interfaces: Ultra SCSI and USB 2.0 /1.1. Connect only one of the USB or SCSI cable.
■ Connecting the SCSI interface 3. Set the SCSI ID using the SCSI ID switch on the back of the scanner. When using the scanner with a SCSI interface, the following SCSI cable and SCSI card must be purchased. • SCSI cable Use a SCSI cable whose connector on the scanner side is the 68-pin high-density shielded-type and whose connector on the PC side fits the connector of the SCSI card to use. It is recommended to use a cable of length 1.5 m or shorter. The SCSI ID is initially set to "5" at the factory.
• Kofax VRS 3. When using the SCSI cable, set the SCSI ID using the SCSI ID switch on the back of the scanner. A software program that allows you to generate highquality images with simple operations. The application automatically detects and corrects document skews during scanning, and characters blurred by coloring or shading. (Refer to step 3 in "Connecting the SCSI interface" on page 5.) • ScandAll PRO 4. Press the "I" side of the main power switch to turn on the scanner.
■ System Requirements ■ Installing the Bundled Software The system requirements for fi-5950 are as follows. The following describes how to install the bundled software from the "Setup DVD-ROM" contained in the scanner package. There are two ways to install the bundled software: [INSTALL (Recommended)] which installs all software programs needed to operate the scanner, or [INSTALL (Custom)] which installs selected software programs one at a time.
■ Installing Adobe® Acrobat® 4. Install the software, following the onscreen instructions. ATTENTION Install Adobe Acrobat using the following procedure from the "Adobe Acrobat DVD-ROM" supplied with the scanner. If Kofax VRS does not support the operating system, the recommended install does not install Kofax VRS. For more details. refer to "System Requirements" (page. 7). You do not have to install Adobe Acrobat if it is already installed on your computer. HINT INSTALL (Custom) 1. 1.
2.4 Checking Scanner Driver Operation 6. In ScandAll PRO, select [Scan] on the menu, and then select [Select Scanner]. 7. Select a scanner in the displayed dialog box. To use TWAIN driver: Select [FUJITSU fi-5950d], and then click the [Select] button. To use ISIS driver: Select [Fujitsu fi-5950], and then click the [Select] button. To use Kofax VRS: Select [Kofax VRS Scanner], and then click the [Select] button.
9. 12. In the [Scan Settings] dialog box, click the [Scan] button. In the [Scan Settings] dialog box, clear the [Save to file] checkbox. ⇒ The document is scanned and the scanned image is displayed in the [ScandAll PRO] window. If the scanned document image is displayed in the window, it means that the scanner driver is installed properly. For further information about how to scan documents, refer to rhe "fi-5950 Operator's Guide" or "ScandAll PRO V2.0 User's Guide" contained in the Setup DVD-ROM. 2.
• To remove FUJITSU Scanner USB HotFix, select "FUJITSU Scanner USB HotFix." HINT • For information about how to uninstall • Image Processing Software Option, refer to the "Image Processing Software Option User’s Guide." For information about how to uninstall Adobe Acrobat, refer to Adobe Acrobat "Read Me." 5. Click the [Change/Remove] button or the [Remove] button. 6. When you see a confirmation dialog box, click the [OK] button or the [Yes] button.
Appendix 1 TROUBLESHOOTING ■ Troubleshooting checklist Symptom Scanner does not turn on. Check this item Remedy Have you pushed the power button on the front of the scanner? Push the power button. Have you pushed the main power switch at the back of the scanner? Push the Main power switch of the scanner. Then push the power button. Is the AC power cable properly connected to the scanner? Correctly connect the AC power able to the scanner adapter. Disconnect the AC power cable, then connect it again.
Symptom Paper is not fed (pick error occurs frequently, or document stops midway). The generated images are elongated. There is a shadow on the leading edge of the generated image. Check this item Remedy Do the documents satisfy the "Document Quality" and the "Multifeed Detection Conditions" in the chapter 7 of the fi-5950 Operator’s Guide? Use the documents that satisfy the "Document Quality" and the "Multifeed Detection Conditions" in chapter 7 of the fi-5950 Operator’s Guide.
■ Temporary error Indication ■ Device alarm (Permanent error) Meaning J0 The paper feeding stopped to protect jammed paper from damage. U1 A paper feed error occurred. U2 A multi feed error occurred. U4 The ADF cover or the pre-imprinter cover is opened. U6 The print cartridge is not set. U8 One of the following error occurred: 1. The document sensors are dirty. 2. The stacker is full. 3. The Brake roller or Separator rollers are not installed properly.
Appendix 2 DAILY CARE CAUTION During its operation, the inside glass of the ADF becomes very hot. Before you clean inside the scanner, turn off its power and unplug the AC adapter from the outlet. Wait for at least 15 minutes. Do not turn off the scanner when you clean the Feed rollers or Eject rollers. ATTENTION It may take long before the cleaner vaporizes if a large quantity is used. When cleaning the scanner parts, dampen a cloth with modest quantities of the cleaner.
Appendix 3 REPLACING CONSUMABLES CAUTION During its operation, the inside glass of the ADF becomes very hot. Before replacing the consumables, turn its power off and unplug the AC adapter from the outlet. Wait at least 15 minutes. The following illustrations show the locations of the consumables. Refer to "5. REPLACEMENT OF CONSUMABLES" in the fi-5950 Operator’s Guide on the Setup DVD-ROM.
■ Pick roller ■ Separator roller Pick roller Separator roller ■ Brake roller Pad Cover Brake roller Cover AP-6
fi-5950 Image Scanner Getting Started P3PC-3062-02EN Issue Date: October, 2011 Issued by: PFU LIMITED Copying of the contents of this manual in whole or in part and copying of the scanner application is prohibited under the copyright law. z The contents of this manual are subject to change without notice. z PFU LIMITED is not liable whatsoever for any damages resulting from use of this scanner and procedures described in this manual, profit loss due to defects, and any claims by a third party.
