Fujitsu Microelectronics Europe User Guide FMEMCU-UG-010003-11 TSC FMA1125 TOUCH SENSOR CONTROLLER SK-TSC-1125S QUICK START GUIDE
SK-TSC-1125S User Guide Revision History Date 2009-11-11 2009-12-15 Issue V1.0, CHa, first official version V1.1, CHa, disclaimer updated, some corrections This document contains 19 pages NOTE: The FMA1125 touch sensor controller is developed and owned by ATLab Inc., South Korea, and is distributed by Fujitsu Microelectronics Europe.
SK-TSC-1125S User Guide Warranty and Disclaimer The use of the deliverables (e.g. software, application examples, target boards, evaluation boards, starter kits, schematics, engineering samples of IC’s etc.) is subject to the conditions of Fujitsu Microelectronics Europe GmbH (“FME”) as set out in (i) the terms of the License Agreement and/or the Sale and Purchase Agreement under which agreements the Product has been delivered, (ii) the technical descriptions and (iii) all accompanying written materials.
SK-TSC-1125S User Guide 0 Contents REVISION HISTORY.............................................................................................................. 2 WARRANTY AND DISCLAIMER ........................................................................................... 3 0 CONTENTS........................................................................................................................ 4 1 OVERVIEW .....................................................................................
SK-TSC-1125S User Guide 1 Overview 1.1 Abstract The SK-TSC-1125S Starter Kit allows easy evaluation of the FMA1125 Touch Sensor Controller. It consists of the following parts: • 1x SK-TSC-1125S-TB touch board with FMA1125 TSC • 1x ADA-16FX-TSC-LCD • 1x 10-pin ribbon cable • 3x FMA1125DC-24S Sample • In order to use the free example software, an SK-16FX-EUROSCOPE Starter Kit is required as host system, which has to be ordered separately.
SK-TSC-1125S User Guide 1.
SK-TSC-1125S User Guide 2 Installation 2.1 Setup (Starter Kit Hardware) Carefully remove the PCBs from the shipping carton. Please follow the steps below to assemble the Starter Kit: 1. Connect the ribbon cable end with the pull relief to X1 on the ADA-16FX-TSC-LCD. Pin1 (Marked on the cable) of the cable must be on the left side close to the pin header X3.
SK-TSC-1125S User Guide 2.2 Setup (PC Software) The installation of the USB driver is described in the SK-16FX-EUROSCOPE documentation. In case the USB connection is only used as power supply, the driver installation is optional. Communication with the demo firmware also is possible using the standard RS232 connector (‘UART A’) on the SK-16FX-EUROSCOPE. The newest version of the demo and tuning firmware can be downloaded at http://www.fujitsu.com/emea/services/microelectronics/tsc/ The .
SK-TSC-1125S User Guide Figure 2: System set-up (LCD and SK-16FX EUROSCOPE not included!) © Fujitsu Microelectronics Europe GmbH -9-
SK-TSC-1125S User Guide 2.4 Jumper settings 2.4.
SK-TSC-1125S User Guide 2.4.
SK-TSC-1125S User Guide 2.
SK-TSC-1125S User Guide 3 Basic Tuning Process using the Command Line Interface and a PC Terminal Program The SK-TSC-1125S kit can also be used together with a demo application running on the SK-16FX-EUROSCOPE to adapt settings like sensitivity and other parameters in the running application and to optimize performance. Here for, only a terminal program is needed on the PC, so it is platform independent.
SK-TSC-1125S User Guide Typically, to start tuning a new application, first of all the Reference Delay and Alpha settings need to be set. For this, the ‘mon2’ monitor mode can help to directly show the effect of changed settings. The Reference Delay is set by the ‘srd nn’ command, where ‘nn’ is the desired value from 0127. A warm reset command is issued automatically to activate the new setting. Typical starting value will be ~50-80, depending on the touch electrodes connected.
SK-TSC-1125S User Guide Figure 3: Monitor Mode (‚mon2’) In mon2 mode, channels with active touch status will be shown with stars ‘*’, those in inactive state are shown with lines ‘|’.
SK-TSC-1125S User Guide 4 Related Products < SK-16FX-EUROSCOPE Evaluation board for the 16FX Family MB96340 Series MCU < SK-TSC-1127-SB Starter Kit for the FMA1127 Touch Sensor Controller with 12 channels - 16 - © Fujitsu Microelectronics Europe GmbH
SK-TSC-1125S User Guide 5 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Touch sensor controllers: http://www.fujitsu.com/emea/services/microelectronics/tsc/ Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/ Linear Products: Power Management, A/D and D/A Converters http://www.fme.fujitsu.com/products/linear/start.
SK-TSC-1125S User Guide 6 China RoHS regulation This starter kit is compliant with China RoHS - 18 - © Fujitsu Microelectronics Europe GmbH
SK-TSC-1125S User Guide 7 Recycling Gültig für EU-Länder: Gemäß der Europäischen WEEE-Richtlinie und deren Umsetzung in landesspezifische Gesetze nehmen wir dieses Gerät wieder zurück. Zur Entsorgung schicken Sie das Gerät bitte an die folgende Adresse: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a D-63225 Langen Valid for European Union Countries: According to the European WEEE-Directive and its implementation into national laws we take this device back.